Page 1
INTEGRATED CIRCUITS
DATA SH EET
TDA8564Q
2 × 24 W BTL or 2 × 12 W
single-ended car radio power
amplifier
Product specification
Supersedes data of February 1995
File under Integrated Circuits, IC01
1995 Dec 13
Page 2
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
FEATURES
• Requires very few external components
• High output power
• Flexibility in use - Quad single-ended or stereo BTL
• Low output offset voltage
• Fixed gain
• Diagnostic facility (distortion, short-circuit and
temperature detection)
• Good ripple rejection
• Mode select switch (operating, mute and standby)
• Load dump protection
• AC and DC short-circuit safe to ground and to V
• Low power dissipation in any short-circuit condition
• Thermally protected
• Reverse polarity safe
P
TDA8564Q
• Electrostatic discharge protection
• No switch-on/switch-off plop
• Flexible leads
• Low thermal resistance
• Identical inputs (inverting and non-inverting).
GENERAL DESCRIPTION
The TDA8564Q is an integrated class-B output amplifier in
a 17-lead DIL-bent-SIL power package. It contains
4 × 12 W single-ended or 2 × 24 W bridge amplifiers.
APPLICATIONS
• The device is primarily developed for car radio
applications.
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
P
I
ORM
I
q(tot)
I
stb
operating supply voltage 6.0 14.4 18.0 V
repetitive peak output current −−4A
total quiescent current − 80 − mA
standby current − 0.1 100 µA
Stereo BTL application
P
o
output power RL=4Ω; THD = 10% − 24 − W
SVRR supply voltage ripple rejection − 41 − dB
V
no
input impedance 25 −−kΩ
Z
I
| DC output offset voltage −−250 mV
|∆V
O
noise output voltage Rs=0Ω−200 −µV
Quad single-ended application
P
o
output power RL=4Ω; THD = 10% − 6.4 − W
=2Ω; THD = 10% − 12 − W
R
L
SVRR supply voltage ripple rejection − 41 − dB
V
no
input impedance 50 −−kΩ
Z
I
noise output voltage Rs=0Ω−200 −µV
ORDERING INFORMATION
TYPE NUMBER
TDA8564Q DBS17P plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm) SOT243-1
1995 Dec 13 2
PACKAGE
NAME DESCRIPTION VERSION
Page 3
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
BLOCK DIAGRAM
handbook, full pagewidth
non-inverting
input 1
inverting
input 2
supply voltage
ripple rejection
non-inverting
input 4
1
60
kΩ
180
Ω
60
kΩ
3
180
Ω
x1
4
17
60
kΩ
180
Ω
18 kΩ
18 kΩ
stand-by
switch
VA
15 kΩ
15 kΩ
mute switch
VA
mute switch
VA
V
P
mute switch
VA
C
m
C
m
PROTECTIONS
thermal
short-circuit
mute
reference
voltage
C
m
power stage
power stage
standby
reference
voltage
mute
switch
V
P1
5
13
TDA8564Q
TDA8564Q
V
P2
6
output 1
8
output 2
mode
14
select
switch
16
diagnostic
output
12
output 4
1995 Dec 13 3
inverting
input 3
18 kΩ
mute switch
60
kΩ
15
180
Ω
input
reference
voltage
2711
ground
(signal)
VA
18 kΩ
9
not connected
C
m
GND1 GND2
power stage
power stage
power ground (substrate)
Fig.1 Block diagram.
10
MLC809
output 3
Page 4
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
PINNING
SYMBOL PIN DESCRIPTION
−INV1 1 non-inverting input 1
SGND 2 signal ground
INV2 3 inverting input 2
SVRR 4 supply voltage ripple rejection
V
P1
OUT1 6 output 1
GND1 7 power ground 1
OUT2 8 output 2
n.c. 9 not connected
OUT3 10 output 3
GND2 11 power ground 2
OUT4 12 output 4
V
P2
MODE 14 mode select switch input
INV3 15 inverting input 3
V
DIAG
−INV4 17 non-inverting input 4
FUNCTIONAL DESCRIPTION
The TDA8564Q contains four identical amplifiers which
can be used for single-ended or bridge applications. The
gain of each amplifier is fixed at 40 dB (46 dB in BTL).
Special features of the device are as follows.
5 supply voltage 1
13 supply voltage 2
16 diagnostic output
handbook, halfpage
TDA8564Q
INV1
1
SGND
2
INV2
3
SVRR
4
V
5
P1
OUT1
6
GND1
7
OUT2
8
n.c.
OUT3
GND2
OUT4
V
P2
MODE
INV3
V
DIAG
INV4
Fig.2 Pin configuration.
9
10
11
12
13
14
15
16
17
TDA8564Q
MLC810
Mode select switch (pin 14)
• Low standby current (<100 µA)
• Low switching current (low cost supply switch)
• Mute facility.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during ≥100 ms (charging of the input
capacitors at pins 1, 3, 15 and 17).
This can be achieved by:
• Microcontroller control
• External timing circuit (see Fig.3).
The circuit in Fig.3 slowly ramps up the voltage at the
mode select switch pin when switching on and results in
fast muting when switching off.
In the event of fast switching at mode select pin it is
advised to increase the
1
⁄2VP decoupling capacitor (pin 4)
to 150 µF to avoid switch plops.
1995 Dec 13 4
handbook, halfpage
Fig.3 Mode select switch circuitry.
V
P
10 kΩ 10 kΩ
47 µF
mode
select
switch
100 kΩ
MGA708
Page 5
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
Diagnostic output (pin 16)
D
YNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 16
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 16 is independent of the number of channels that are
clipping (see Figs 4 and 5).
HORT-CIRCUIT PROTECTION
S
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
20 ms after removal of the short-circuit. During this
short-circuit condition, pin 16 is continuously LOW.
When a short-circuit across the load of one or more
channels occurs the output stages are switched off during
TDA8564Q
approximately 20 ms. After that time it is checked during
approximately 50 µs to see whether the short-circuit is still
present. Due to this duty cycle of 50 µs/20 ms the average
current consumption during this short-circuit condition is
very low (approximately 40 mA).
During this short-circuit condition, pin 16 is LOW for 20 ms
and HIGH for 50 µs (see Fig.6).
The power dissipation in any short-circuit condition is
very low.
EMPERATURE DETECTION
T
When the virtual junction temperature Tvj reaches 150 °C,
pin 16 will be active LOW.
PEN-COLLECTOR OUTPUT
O
Pin 16 is an open-collector output, which allows pin 16 of
more devices being tied together.
handbook, halfpage
V
O
0
V
16
V
P
0
MGA705
t
Fig.4 Distortion detector waveform; BTL application.
handbook, full pagewidth
current
in
output
stage
V
15
short-circuit over the load
V
P
handbook, halfpage
Fig.5 Distortion detector waveform;
20 ms
V
O
0
V
16
V
P
0
single-ended application.
MGA706
t
MGA707
t
1995 Dec 13 5
50 µs
t
Fig.6 Short-circuit waveform.
Page 6
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
TDA8564Q
car radio power amplifier
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
V
P
V
psc
V
pr
I
OSM
I
ORM
P
tot
T
stg
T
amb
T
vj
supply voltage
operating − 18 V
non-operating − 30 V
load dump protection during 50 ms; t
≥ 2.5 ms − 45 V
r
AC and DC short-circuit safe voltage − 18 V
reverse polarity − 6V
non-repetitive peak output current − 6A
repetitive peak output current − 4A
total power dissipation − 60 W
storage temperature −55 +150 °C
operating ambient temperature −40 +85 °C
virtual junction temperature − 150 °C
THERMAL CHARACTERISTICS
SYMBOL PARAMETER VALUE UNIT
R
th j-a
R
th j-c
ndbook, halfpage
thermal resistance from junction to ambient in free air 40 K/W
thermal resistance from junction to case (see Figs 7 and 8) 1.3 K/W
virtual junction
output 3 output 4
3.0 K/W
3.0 K/W
0.7 K/W
0.2 K/W
virtual junction
2.2 K/W
output 1 output 2
0.2 K/W
case
MEA861 - 1
handbook, halfpage
output 1 output 2
3.0 K/W
2.2 K/W
0.7 K/W
MEA860 - 2
3.0 K/W
Fig.7 Equivalent thermal resistance network;
BTL application.
1995 Dec 13 6
case
Fig.8 Equivalent thermal resistance network;
single-ended application.
Page 7
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
TDA8564Q
car radio power amplifier
DC CHARACTERISTICS
V
= 14.4 V; T
P
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
V
P
I
q
V
O
DC output offset voltage −−250 mV
∆V
O
Mute select switch
V
14
MUTE CONDITION
V
mute
V
O
DC output offset voltage −−250 mV
∆V
O
STANDBY CONDITION
V
stb
I
stb
I
sw
Diagnostic output (pin 16)
V
DIAG
=25°C; measured in Fig.17; unless otherwise specified.
amb
supply voltage note 1 6.0 14.4 18.0 V
quiescent current see Fig.9 − 80 160 mA
DC output voltage note 2 − 6.9 − V
switch-on voltage level 8.5 −−V
mute voltage 3.3 − 6.4 V
output signal in mute position V
=1V; f=1kHz −−20 mV
I(max)
DC voltage in standby condition 0 − 2V
DC current in standby condition −−100 µA
switch-on current − 12 40 µA
diagnostic output voltage any short-circuit or clipping −−0.6 V
Notes
1. The circuit is DC adjusted at V
= 6 to 18 V and AC operating at VP= 8.5 to 18 V.
P
2. At 18 V < VP< 30 V the DC output voltage ≤1⁄2VP.
1995 Dec 13 7
Page 8
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
TDA8564Q
car radio power amplifier
AC CHARACTERISTICS
V
= 14.4 V; RL=4Ω; f = 1 kHz; T
P
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Stereo BTL application (measured in Fig.17)
P
o
P
o
output power THD = 0.5%; note 1 15 19 − W
output power VP= 13.2 V; THD = 0.5%; note 1 − 16 − W
THD total harmonic distortion P
f
lr
f
hr
G
v
low frequency roll-off at −1 dB; note 2 − 45 − Hz
high frequency roll-off at −1dB 20 −−kHz
closed loop voltage gain 45 46 47 dB
SVRR supply voltage ripple rejection
on note 3 38 41 − dB
mute note 3 42 48 − dB
standby note 3 80 −−dB
input impedance 25 30 38 kΩ
Z
i
V
no
noise output voltage
on R
on R
mute notes 4 and 5 − 180 −µV
α
cs
channel unbalance −−1dB
∆G
v
channel separation Rs=10kΩ 40 −−dB
DYNAMIC DISTORTION DETECTOR
THD total harmonic distortion V16≤ 0.6 V; no short-circuit − 10 − %
=25°C; unless otherwise specified.
amb
THD = 10%; note 1 20 24 − W
= 13.2 V; THD = 10%; note 1 − 20 − W
V
P
=1W − 0.1 − %
o
=0Ω; note 4 − 200 −µV
s
=10kΩ; note 4 − 350 700 µV
s
1995 Dec 13 8
Page 9
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
TDA8564Q
car radio power amplifier
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Quad single-ended application (measured in Fig.18)
P
o
P
o
THD total harmonic distortion P
f
lr
f
hr
G
v
SVRR supply voltage ripple rejection
input impedance 50 60 75 kΩ
Z
i
V
no
α
cs
channel unbalance −−1dB
∆G
v
DYNAMIC DISTORTION DETECTOR
THD total harmonic distortion V16≤ 0.6 V; no short-circuit − 10 − %
output power THD = 0.5%; note 1 4 5 − W
THD = 10%; note 1 5.5 6.4 − W
output power RL=2Ω; THD = 0.5%; note 1 7.5 8.5 − W
=2Ω; THD = 10%; note 1 10 12 − W
R
L
=1W − 0.15 − %
o
low frequency roll-off at −3 dB; note 2 − 45 − Hz
high frequency roll-off at −1dB 20 −−kHz
closed loop voltage gain 39 40 41 dB
on note 3 38 41 − dB
mute note 3 42 48 − dB
standby note 3 80 90 − dB
noise output voltage
on R
on R
=0Ω; note 4 − 200 300 µV
s
=10kΩ; note 4 − 250 −µV
s
mute notes 4 and 5 − 175 −µV
channel separation Rs=10kΩ 40 52 − dB
Notes
1. Output power is measured directly at the output pins of the IC.
2. Frequency response externally fixed.
3. Ripple rejection measured at the output with a source impedance of 0 Ω, maximum ripple amplitude of 2 V (p-p).
4. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz.
5. Noise output voltage independent of Rs(VI= 0 V).
1995 Dec 13 9
Page 10
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
100
handbook, full pagewidth
I
q
(mA)
92
84
76
68
60
8 1012 1416
TDA8564Q
MGA714
V (V)
P
18
10
handbook, full pagewidth
THD
(%)
1
1
10
2
10
1
Fig.9 Quiescent current as a function of supply voltage; RL= ∞.
(1)
10110
P (W)
o
MLC811
2
10
(1) f = 1 kHz.
Fig.10 Total harmonic distortion as a function of output power; VP= 14.4 V; RL=4Ω (BTL).
1995 Dec 13 10
Page 11
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
50
handbook, full pagewidth
P
o
(W)
40
30
20
10
0
810121416
(1) THD = 30%.
(2) THD = 10%.
(3) THD = 0.5%.
(1)
(2)
(3)
TDA8564Q
MGA710
V (V)
P
18
10
handbook, full pagewidth
THD
(%)
1
1
10
2
10
1
Fig.11 Output power as a function of supply voltage (BTL).
(1)
10110
P (W)
o
MLC812
2
10
(1) f = 1 kHz.
Fig.12 Total harmonic distortion as a function of output power; VP= 14.4 V; RL=4Ω (single-ended).
1995 Dec 13 11
Page 12
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
15
handbook, full pagewidth
P
o
(W)
12
9
6
3
0
8 10121416
(1) THD = 30%.
(2) THD = 10%.
(3) THD = 0.5%.
(1)
(2)
(3)
TDA8564Q
MGA716
V (V)
P
18
THD
(%)
10
10
1
1
2
10
handbook, full pagewidth
Fig.13 Output power as a function of supply voltage (single-ended).
(1)
2
10
3
10
4
10
f (Hz)
MLC813
5
10
(1) Po=1W.
Fig.14 Total harmonic distortion as a function of frequency; VP= 14.4 V; RL=4Ω (single-ended).
1995 Dec 13 12
Page 13
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
30
handbook, full pagewidth
α
cs
(dB)
40
50
60
70
80
10
2
10
TDA8564Q
MGA719
3
10
4
10
f (Hz)
5
10
35
handbook, full pagewidth
SVRR
(dB)
40
45
50
55
60
10
Fig.15 Channel separation as a function of frequency.
(1)
2
10
3
10
10
MLC814
4
f (Hz)
5
10
(1) On condition.
Fig.16 Ripple rejection as a function of frequency; VP= 14.4 V; V
1995 Dec 13 13
= 2 V (p-p); Rs=0Ω(single-ended).
ripple
Page 14
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
TEST AND APPLICATION INFORMATION
handbook, full pagewidth
non- inverting
input 1
inverting input 2
ground (signal)
supply voltage
ripple rejection
non-inverting
input 4
220 nF
220 nF
mode
switch
diagnostic
14
TDA8564Q
1
60
kΩ
3
2
4
17
16 5 13
60
kΩ
60
kΩ
10
kΩ
reference
voltage
12
6
8
9
100
nF
not connected
2200
µF
TDA8564Q
V
P
60
kΩ
inverting input 3
15
711
power ground (substrate)
Fig.17 Stereo BTL application circuit diagram.
10
MGC046
1995 Dec 13 14
Page 15
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
handbook, full pagewidth
non- inverting
input 1
inverting
input 2
ground (signal)
supply voltage
ripple rejection
non-inverting
input 4
220 nF
220 nF
220 nF
mode
switch
TDA8564Q
1
3
2
4
1/2V
p
17
14
60
kΩ
60
kΩ
60
kΩ
10
kΩ
16 5 13
reference
voltage
60
kΩ
12
6
8
9
100
nF
not connected
2200
µF
1000 µF
1000 µF
1000 µF
V
P
TDA8564Q
inverting
input 3
220 nF
15
711
power ground (substrate)
10
MGC047
Fig.18 Quad single-ended application circuit diagram 1.
1000 µF
1995 Dec 13 15
Page 16
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
handbook, full pagewidth
non- inverting
input 1
inverting
input 2
ground (signal)
not connected
non-inverting
input 4
220 nF
220 nF
220 nF
mode
switch
TDA8564Q
1
3
2
9
17
14
60
kΩ
60
kΩ
10
kΩ
16 5 13
reference
voltage
60
kΩ
TDA8564Q
V
P
100
µF
2200
µF
(1)
D1
100
nF
6
8
SVRR
4
12
60
kΩ
inverting
input 3
(1) When short-circuiting the single-ended capacitor, the dissipation will be reduced due diode D1.
220 nF
15
711
MGC048
power ground (substrate)
Fig.19 Quad single-ended application circuit diagram 2.
10
2200
µF
1995 Dec 13 16
Page 17
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
PACKAGE OUTLINE
DBS17P: plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm)
non-concave
D
d
x
E
h
D
h
view B: mounting base side
A
2
TDA8564Q
SOT243-1
117
e
Z
DIMENSIONS (mm are the original dimensions)
UNIT A e
mm
A2bpcD
17.0
4.6
4.2
0.75
0.60
15.5
0.48
0.38
1
e
(1)
deD
24.0
20.0
23.6
19.6
w M
b
p
(1)
E
h
12.2
10 2.54
11.8
0 5 10 mm
B
j
L
3
1.27
scale
1
e
5.08
L
E
2
h
6
Q
LL3m
3.4
12.4
3.1
11.0
c
2.4
1.6
e
4.3
m
E
A
2.1
1.8
v M
(1)
v
Qj
0.8
0.4w0.03
Z
x
2.00
1.45
2
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT243-1
1995 Dec 13 17
REFERENCES
IEC JEDEC EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-03-11
Page 18
Philips Semiconductors Product specification
2 × 24 W BTL or 2 × 12 W single-ended
car radio power amplifier
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“IC Package Databook”
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
(order code 9398 652 90011).
TDA8564Q
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
stg max
). If the
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICA TIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1995 Dec 13 18
Loading...