Datasheet TDA8351 Datasheet (Philips)

INTEGRATED CIRCUITS

DATA SH EET

TDA8351

DC-coupled vertical deflection
circuit

Preliminary specification
Supersedes data of June 1992
File under Integrated Circuits, IC02

Philips Semiconductors

January 1995

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

FEATURES

• Few external components

• Highly efficient fully DC-coupled vertical output bridge

circuit

• Vertical flyback switch

GENERAL DESCRIPTION

The TDA8351 is a power circuit for use in 90° and 110°
colour deflection systems for field frequencies of 50 to
120 Hz. The circuit provides a DC driven vertical deflection
output circuit, operating as a highly efficient class G
system.

• Guard circuit

• Protection against:

– short-circuit of the output pins (7 and 4)
– short-circuit of the output pins to V

P

• Temperature (thermal) protection

• High EMC immunity because of common mode inputs

• A guard signal in zoom mode.

QUICK REFERENCE DATA

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

DC supply

V

P

I

q

supply voltage 9 − 25 V
quiescent supply current − 30 − mA

Vertical circuit

I

O(p-p)

output current

−−3A

(peak-to-peak value)

I

diff(p-p)

differential input current

− 600 −µA

(peak-to-peak value)

V

diff(p-p)

differential input voltage

− 1.5 1.8 V

(peak-to-peak value)

Flyback switch

I

M

V

FB

peak output current −−±1.5 A
flyback supply voltage −−50 V

note 1 −−60 V

Thermal data (in accordance with IEC 747-1)

T

stg

T

amb

T

vj

storage temperature −55 − +150 °C
operating ambient temperature −25 − +75 °C
virtual junction temperature −−150 °C

Note

1. A flyback supply voltage of>50 V up to 60 V is allowed in application. A 220 nF capacitor in series with a 22 Ω resistor
(dependent on I

and the inductance of the coil) has to be connected between pin 7 and ground. The decoupling

O

capacitor of VFB has to be connected between pin 6 and pin 3. This supply voltage line must have a resistance of
33 Ω (see application circuit Fig.6).

January 1995 2

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

ORDERING INFORMATION

TYPE NUMBER

TDA8351 SIL9P plastic single-in-line power package; 9 leads SOT131-2

BLOCK DIAGRAM

handbook, full pagewidth

NAME DESCRIPTION VERSION

V

P

36

V

P

TDA8351

I

drive(pos)

I

drive(neg)

1

2

V

V

O(guard)

8

CURRENT

SOURCE

I

S

I

S

I

T

I

T

PACKAGE

V

FB

V

P

V

V

O(A)

P

7

V

O(A)

9

V

I(fb)

5
GND

Fig.1 Block diagram.

January 1995 3

V

O(B)

MBC988- 1

4

V

O(B)

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

PINNING

SYMBOL PIN DESCRIPTION

I

drive(pos)

I

drive(neg)

V

P

V

O(B)

1 input power-stage (positive);

includes I

signal bias

I(sb)

2 input power-stage (negative);

includes I

signal bias

I(sb)

3 operating supply voltage

4 output voltage B
GND 5 ground
V

FB

V

O(A)

V

O(guard)

V

I(fb)

handbook, 2 columns

I

drive(pos)

I

drive(neg)

V

6 input flyback supply voltage

7 output voltage A

8 guard output voltage

9 input feedback voltage

1
2

V

3

P

V

O(B)

4

GND

5

TDA8351

V

6

FB

V

O(guard)

O(A)

V

I(fb)

7
8
9

FUNCTIONAL DESCRIPTION

The vertical driver circuit is a bridge configuration. The
deflection coil is connected between the output amplifiers,
which are driven in phase opposition. An external resistor
(RM) connected in series with the deflection coil provides
internal feedback information. The differential input circuit
is voltage driven. The input circuit has been adapted to
enable it to be used with the TDA9150, TDA9151B,
TDA9160A, TDA9162, TDA8366 and TDA8376 which
deliver symmetrical current signals. An external resistor
(R

) connected between the differential input

CON

determines the output current through the deflection coil.
The relationship between the differential input current and
the output current is defined by: I

diff

× R

CON=Icoil

× RM.
The output current is adjustable from 0.5 A (p-p) to 3 A
(p-p) by varying RM. The maximum input differential
voltage is 1.8 V. In the application it is recommended that
V

= 1.5 V (typ). This is recommended because of the

diff

spread of input current and the spread in the value of
R

.

CON

The flyback voltage is determined by an additional supply
voltage VFB. The principle of operating with two supply
voltages (class G) makes it possible to fix the supply
voltage VP optimum for the scan voltage and the second
supply voltage VFB optimum for the flyback voltage. Using
this method, very high efficiency is achieved.

The supply voltage VFB is almost totally available as
flyback voltage across the coil, this being possible due to
the absence of a decoupling capacitor (not necessary, due
to the bridge configuration). The output circuit is fully
protected against the following:

• thermal protection

• short-circuit protection of the output pins (pins 4 and 7)

• short-circuit of the output pins to VP.

MBC989

Metal block connected to substrate pin 5.
Metal on back.

Fig.2 Pin configuration.

January 1995 4

A guard circuit V

is provided. The guard circuit is

O(guard)

activated at the following conditions:

• during flyback

• during short-circuit of the coil and during short-circuit of

the output pins (pins 4 and 7) to VP or ground

• during open loop

• when the thermal protection is activated.

This signal can be used for blanking the picture tube
screen.

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

LIMITING VALUES

In accordance with the Absolute Maximum Rating System (IEC 134).

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

DC supply

V

P

V

FB

Vertical circuit

I

O(p-p)

V

O(A)

Flyback switch

I

M

Thermal data (in accordance with IEC 747-1)

T

stg

T

amb

T

vj

R

th vj-c

R

th vj-a

t

sc

supply voltage non-operating − 40 V

− 25 V

flyback supply voltage − 50 V

note 1 − 60 V

output current (peak-to-peak value) note 2 − 3A
output voltage (pin 7) − 52 V

note 1 − 62 V

peak output current −±1.5 A

storage temperature −55 +150 °C
operating ambient temperature −25 +75 °C
virtual junction temperature − 150 °C
resistance vj-case − 4 K/W
resistance vj-ambient in free air − 40 K/W
short-circuiting time note 3 − 1hr

Notes

1. A flyback supply voltage of>50 V up to 60 V is allowed in application. A 220 nF capacitor in series with a 22 Ω resistor
(dependent on I

and the inductance of the coil) has to be connected between pin 7 and ground. The decoupling

O

capacitor of VFB has to be connected between pin 6 and pin 3. This supply voltage line must have a resistance of
33 Ω (see application circuit Fig.6).

2. IO maximum determined by current protection.

3. Up to VP=18V.

January 1995 5

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

CHARACTERISTICS

VP= 17.5 V; T
specified.

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

DC supply

V

P

V

FB

I

P

Vertical circuit

V

O

LE linearity error I

V

O

V

DF

|I

| output offset current I

os

| offset voltage at the input of the

|V

os

∆V

T output offset voltage as a function

os

V

O(A)

G

vo

V

R

f

res

G

I

T current gain drift as a function of

∆G

c

I

I(sb)

I

FB

PSRR power supply ripple rejection note 7 − 80 − dB
V

I(DC)

V

I(CM)

I

bias

I

O(CM)

=25°C; VFB= 45 V; fi= 50 Hz; I

amb

= 400 µA; measured in test circuit of Fig.3; unless otherwise

I(sb)

operating supply voltage 9.0 − 25 V
flyback supply voltage V

note 1 V

P
P

− 50 V

− 60 V

supply current no signal; no load − 30 55 mA

output voltage swing (scan) I

= 0.6 mA (p-p);

diff

V

= 1.8 V (p-p);

diff

19.8 −−V

IO= 3 A (p-p)

= 3 A (p-p); note 2 − 12%

O

I

= 50 mA (p-p); note 2 − 12%

O

output voltage swing (flyback)
V

O(A)-VO(B)

forward voltage of the internal
efficiency diode (V

O(A)-VFB

feedback amplifier (V

)

I(fb)-VO(B)

I

= 0.3 mA;

diff

IO= 1.5 A (M)
IO= −1.5 A (M);

I

= 0.3 mA

diff

=0;

diff

I

=50to500µA

I(sb)

I

=0;

diff

)

I

=50to500µA

I(sb)

I

=0 −−72 µV/K

diff

− 39 − V

−−1.5 V

−−30 mA

−−18 mV

of temperature
DC output voltage I
open-loop voltage gain (V

7-4/V1-2

open loop voltage gain
(V

voltage ratio V

7-4/V9-4

; V

1-2

=0)

1-2/V9-4

= 0; note 3 − 8.0 − V

diff

) notes 4 and 5 − 80 − dB

note 4 − 80 − dB

− 0 − dB
frequency response (−3 dB) open loop; note 6 − 40 − Hz
current gain (IO/I

) − 5000 −

diff

−−10

−4

K

temperature
signal bias current 50 400 500 µA
flyback supply current during scan −−100 µA

DC input voltage − 2.7 − V
common mode input voltage I
input bias current I
common mode output current ∆I

=0 0 − 1.6 V

I(sb)

=0 − 0.1 0.5 µA

I(sb)

= 300 µA (p-p);

I(sb)

fi= 50 Hz; I

diff

=0

− 0.2 − mA

January 1995 6

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Guard circuit

I

O

V

O(guard)

output current not active;

V

O(guard)

active; V

=0V

O(guard)

= 4.5 V 1 − 2.5 mA
output voltage on pin 8 IO= 100 µA −−5.5 V
allowable voltage on pin 8 maximum leakage

current = 10 µA;

Notes

1. A flyback supply voltage of>50 V up to 60 V is allowed in application. A 220 nF capacitor in series with a 22 Ω resistor
(dependent on IO and the inductance of the coil) has to be connected between pin 7 and ground. The decoupling
capacitor of VFB has to be connected between pin 6 and pin 3. This supply voltage line must have a resistance of
33 Ω (see application circuit Fig.6).

2. The linearity error is measured without S-correction and based on the same measurement principle as performed on
the screen. The measuring method is as follows:
Divide the output signal I

4-I7(VRM

) into 22 equal parts ranging from 1 to 22 inclusive. Measure the value of two
succeeding parts called one block starting with part 2 and 3 (block 1) and ending with part 20 and 21 (block 10). Thus
part 1 and 22 are unused. The equations for linearity error for adjacent blocks (LEAB) and not adjacent blocks (NAB)
are given below

–

a

LEAB

kak1+()

= NAB

----------------------------- ­a

3. Referenced to V

avg

;

.

P

=

–

a

maxamin

----------------------------- ­a

avg

4. V values within formulae, relate to voltages at or between relative pin numbers, i.e. V
pins 7 and 4 divided by voltage value across pins 1 and 2.

5. V

6. Frequency response V

7. At V

AC short-circuited.

9-4

= 500 mV eff; measured across RM; fi= 50 Hz.

(ripple)

is equal to frequency response V

7-4/V9-4

7-4/V1-2

−−50 µA

−−40 V

7-4/V1-2

= voltage value across

.

January 1995 7

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

handbook, full pagewidth

I

I(sb)

signal

bias

I

drive(pos)

I

drive(neg)

signal

bias

I

I(sb)

R

CON

3 kΩ

V

O(guard)

TDA8351

1

I

diff

2

V

2.2 kΩ

86

FEEDBACK

INPUT

5

GND

MBC987 - 1

Fig.3 Test diagram.

V

FB

3

7

9

4

V

P

R = 6.0 Ω

R = 0.7 Ω

M

handbook, full pagewidth

I

diff

I

sb

0

I

diff

I

sb

0

Fig.4 Input currents.

January 1995 8

diff

I

sb

1

R

CON

I

sb

TDA8351

2

MLA776

I

sb

I

diff

I

I

diff

I

sb

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

APPLICATION INFORMATION

handbook, full pagewidth

VP= 14 V; I

O(p-p)

I

I(sb)

signal

bias

I

drive(pos)

I

drive(neg)

signal

bias

I

I(sb)

= 2.14 A; I

= 400 µA; I

I(sb)

R

CON
3 kΩ

diff(p-p)

V

O(guard)

86

TDA8351

1

I

diff

2

V

= 500 µA; VFB= 42 V; tFB= 0.6 ms.

Fig.5 Application diagram.

FEEDBACK

5

GND

INPUT

3

7

9

4

MBC986 - 1

V

V

V

O(A)

I(fb)

O(B)

100

nF

I

(coil)

V

FB

V

P

deflection coil
AT6005/31
L = 8.63 mH
R = 5.0 Ω

R = 0.7 Ω

M

January 1995 9

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

handbook, full pagewidth

signal

signal

VP= 14 V; I

O(p-p)

= 2.14 A; I

I

I(sb)

bias

bias
I

I(sb)

I

I

drive(pos)

drive(neg)

I(sb)

R

CON
3 kΩ

= 400 µA; I

V

O(guard)

86

TDA8351

1

I

diff

2

V

= 500 µA; VFB= 60 V; tFB= 0.4 ms.

diff(p-p)

FEEDBACK

5

GND

INPUT

MLA777

3

7

9

4

100
nF

V

O(A)

V

I(fb)

R = 0.7 Ω

M

V

O(B)

I

(coil)

30

V

P

220 nF

20 Ω

V

FB

deflection coil
AT6005/31
L = 8.63 mH
R = 5.0 Ω

Fig.6 Application circuit; 50 V ≤ VFB≤ 60 V.

January 1995 10

Philips Semiconductors Preliminary specification



DC-coupled vertical deflection circuit TDA8351

PACKAGE OUTLINE

24.4

handbook, full pagewidth

12.4

11.6

3.4

3.1

0.05 convex

987654321

23.6

20.0

19.6
10

,

mounting
base

6

seating plane

4.7

4.1

17.2

16.5

Dimensions in mm.

2.20

1.45

0.75

0.60

0.25 M
(9x)

2.54
(8x)

MBC360

Fig.7 Plastic single-in-line power package; 9 leads (SIL9P; SOT131-2).

0.55

0.35

2.1

1.8

January 1995 11

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

SOLDERING
Plastic single in-line packages

Y DIP OR WAVE

B
The maximum permissible temperature of the solder is

260 °C; this temperature must not be in contact with the
joint for more than 5 s. The total contact time of successive
solder waves must not exceed 5 s.

The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of this specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.

specified storage maximum. If the printed-circuit board has
been pre-heated, forced cooling may be necessary
immediately after soldering to keep the temperature within
the permissible limit.

R

EPAIRING SOLDERED JOINTS

Apply the soldering iron below the seating plane (or not
more than 2 mm above it. If its temperature is below
300 °C, it must not be in contact for more than 10 s; if
between 300 and 400 °C, for not more than 5 s.

Application information

Where application information is given, it is advisory and does not form part of the specification.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

January 1995 12

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

NOTES

January 1995 13

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

NOTES

January 1995 14

Philips Semiconductors Preliminary specification

DC-coupled vertical deflection circuit TDA8351

NOTES

January 1995 15

Philips Semiconductors – a worldwide company

Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)

BUENOS AIRES, Tel. [phone], Fax. [phone]

Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,

Tel. [phone], Fax. [phone]

Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,

Tel. [phone], Fax. [phone]

Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,

Tel. [phone], Fax. [phone]

Brazil: Rua do Rocio 220 - 5

CEP: 04552-903-SÃO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Tel. [phone], Fax. [phone]

Canada: PHILIPS SEMICONDUCTORS/COMPONENTS:

Tel. [phone], Fax. [phone]

Chile: Av. Santa Maria 0760, SANTIAGO,

Tel. [phone], Fax. [phone]

Colombia: IPRELENSO LTDA, Carrera 21 No. 56-17,

77621 BOGOTA, Tel. [phone],
Fax. [phone]

Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,

Tel. [phone], Fax. [phone]

Finland: Sinikalliontie 3, FIN-02630 ESPOO,

Tel. [phone], Fax. [phone]

France: 4 Rue du Port-aux-Vins, BP317,

92156 SURESNES Cedex,
Tel. [phone], Fax. [phone]

Germany: P.O. Box 10 63 23, 20043 HAMBURG,

Tel. [phone], Fax. [phone].

Greece: No. 15, 25th March Street, GR 17778 TAVROS,

Tel. [phone] 911, Fax. [phone]

Hong Kong: PHILIPS HONG KONG Ltd., 6/F Philips Ind. Bldg.,

24-28 Kung Yip St., KWAI CHUNG, N.T.,
Tel. [phone], Fax. [phone]

India: Philips INDIA Ltd, Shivsagar Estate, A Block ,

Dr. Annie Besant Rd. Worli, Bombay 400 018
Tel. [phone], Fax. [phone]

Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,

P.O. Box 4252, JAKARTA 12950,
Tel. [phone], Fax. [phone]

Ireland: Newstead, Clonskeagh, DUBLIN 14,

Tel. [phone], Fax. [phone]

Italy: PHILIPS SEMICONDUCTORS S.r.l.,

Piazza IV Novembre 3, 20124 MILANO,
Tel. [phone], Fax. [phone]

Japan: Philips Bldg13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,

Tel. [phone], Fax. [phone]

Korea: (Republic of) Philips House, 260-199 Itaewon-dong,

Yongsan-ku, SEOUL, Tel. [phone], Fax. [phone]

Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,

SELANGOR, Tel. [phone], Fax. [phone]

Mexico: 5900 Gateway East, Suite 200, EL PASO, TX 79905,

Tel. [phone], Fax. [phone]

Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB

Tel. [phone], Fax. [phone]

New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,

Tel. [phone], Fax. [phone]

Norway: Box 1, Manglerud 0612, OSLO,

Tel. [phone], Fax. [phone]

th

floor, Suite 51,

Pakistan: Philips Electrical Industries of Pakistan Ltd.,

Exchange Bldg. ST-2/A, Block 9, KDA Scheme 5, Clifton,
KARACHI 75600, Tel. [phone],
Fax. [phone].

Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,

106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. [phone], Fax. [phone]

Portugal: PHILIPS PORTUGUESA, S.A.,

Rua dr. António Loureiro Borges 5, Arquiparque - Miraflores,
Apartado 300, 2795 LINDA-A-VELHA,
Tel. [phone], Fax. [phone].

Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,

Tel. [phone], Fax. [phone]

South Africa: S.A. PHILIPS Pty Ltd.,

195-215 Main Road Martindale, 2092 JOHANNESBURG,
P.O. Box 7430 Johannesburg 2000,
Tel. [phone], Fax. [phone].

Spain: Balmes 22, 08007 BARCELONA,

Tel. [phone], Fax. [phone]

Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,

Tel. [phone], Fax. [phone]

Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,

Tel. [phone], Fax. [phone]

Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66, Chung Hsiao West

Road, Sec. 1. Taipeh, Taiwan ROC, P.O. Box 22978,
TAIPEI 100, Tel. [phone], Fax. [phone].

Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,

209/2 Sanpavuth-Bangna Road Prakanong,
Bangkok 10260, THAILAND,
Tel. [phone], Fax. [phone].

Turkey:Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,

Tel. [phone], Fax. [phone]

United Kingdom: Philips Semiconductors LTD.,

276 Bath Road, Hayes, MIDDLESEX UB3 5BX,
Tel. [phone], Fax. [phone]

United States:811 East Arques Avenue, SUNNYVALE,

CA 94088-3409, Tel. [phone], Fax. [phone]

Uruguay: Coronel Mora 433, MONTEVIDEO,

Tel. [phone], Fax. [phone]

For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BE-p,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. [phone]

SCD36 © Philips Electronics N.V. 1994

All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.

Printed in The Netherlands

533061/1500/02/pp16 Date of release: January 1995
Document order number: 9397 745 10011

Philips Semiconductors