Page 1
INTEGRATED CIRCUITS
DATA SH EET
TDA3507
Video control combination circuit
with automatic cut-off control
Product specification
File under Integrated Circuits, IC02
November 1987
Page 2
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
GENERAL DESCRIPTION
The TDA3507 is a monolithic integrated circuit which performs video control functions in a PAL/SECAM decoder.
The required input signals are: luminance and negative colour difference −(R−Y) and −(B−Y), and a 3-level sandcastle
pulse for control purposes. Linear RGB signals can be inserted from an external source. RGB output signals are available
for driving the video output stages. This circuit provides automatic cut-off control of the picture tube.
The TDA3507 is the same as the TDA3505 but with RGB channel bandwidths of (typical) 16 MHz and an automatic
cut-off cycle that ends in line 15.
Features
• Capacitive coupling of the colour difference and
luminance input signals with black level clamping in the
input stages
• Linear saturation control acting on the colour difference
signals
• (G−Y) and RGB matrix
• Linear transmission of inserted signals
• Equal black levels for inserted and matrixed signals
• 3 identical channels for the RGB signals
• Linear contrast and brightness controls, operating on
both the inserted and matrixed RGB signals
• Peak beam current limiting input
• Clamping, horizontal and vertical blanking of the three
input signals controlled by a 3-level sandcastle pulse
• 3 DC gain controls for the RGB output signals (white
point adjustment)
• Emitter-follower outputs for driving the RGB output
stages
• Input for automatic cut-off control with compensation for
leakage current of the picture tube
QUICK REFERENCE DATA
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Supply voltage (pin 6) V
Supply current I
Composite video input
signal (peak-to-peak value) V
Colour difference input
signals (peak-to-peak value)
−(B−Y) V
−(R−Y) V
Inserted RGB signals
(black-to-white value) V
Three-level sandcastle pulse V
Control voltage ranges
brightness V
contrast V
saturation V
= V
P
6-24
= I
P
6
15-24(p-p)
18-24(p-p)
17-24(p-p)
12,13,14-24
10-24
20-24
19-24
16-24
− 12 − V
− 100 − mA
− 0,45 − V
− 1,33 − V
− 1,05 − V
− 1,0 − V
− 2,5 − V
− 4,5 − V
− 8,0 − V
1,0 − 3,0 V
2,0 − 4,3 V
2,0 − 4,3 V
PACKAGE OUTLINE
28-lead DIL; Plastic (SOT117); SOT117-1; 1996 November 21.
November 1987 2
Page 3
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
TDA3507
November 1987 3
Fig.1 Part of block diagram, continued in Fig.2.
Page 4
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
TDA3507
November 1987 4
Fig.2 Part of block diagram, continued from Fig.1.
Page 5
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
PINNING
PIN DESCRIPTION
1 red output
2 green storage capacitor for cut-off control
3 green output
4 blue storage capacitor for cut-off control
5 blue output
6 positive supply voltage (+12 V)
7 blue storage for brightness
8 green storage for brightness
9 red storage for brightness
10 sandcastle pulse input
11 fast switch for RGB inputs
12 blue input (external signal)
13 green input (external signal)
14 red input (external signal)
15 luminance input
16 saturation control input
17 −(R−Y) colour difference input
18 −(B−Y) colour difference input
19 contrast control input
20 brightness control input
21 white point adjustment, blue
22 white point adjustment, green
23 white point adjustment, red
24 ground (0 V)
25 control input for peak beam current limiting
26 automatic cut-off control input
27 storage capacitor for leakage current
28 red storage capacitor for cut-off control
TDA3507
November 1987 5
Page 6
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
PARAMETER SYMBOL MIN. MAX. UNIT
Supply voltage (pin 6) V
Voltage ranges
at pins 10, 21, 22, 23, 25, 26 V
at pin 11 V
at pins 16, 19, 20 V
at pins 1, 2, 3, 4, 5, 7, 8, 9,
12, 13, 14, 15, 17, 18, 27, 28 no external DC voltage
Currents
at pins 1, 3, 5 −I
at pin 19 I
at pin 20 I
at pin 25 −I
Total power dissipation P
Storage temperature range T
Operating ambient temperature range T
= V
P
6-24
n-24
11-24
16, 19, 20-24
1, 3, 5
19
20
25
tot
stg
amb
TDA3507
− 13,2 V
0V
P
−0,5 3,0 V
0 0,5V
P
− 3mA
− 10 mA
− 5mA
− 5mA
− 1,7 W
−25 +150 °C
0 +70 °C
V
V
November 1987 6
Page 7
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
CHARACTERISTICS
= V
V
P
measured in Fig.3; nominal settings of brightness, contrast, saturation and white point adjustment; all voltages are
referred to pin 24; unless otherwise specified
Supply (pin 6)
Supply voltage V
Supply current I
Colour difference inputs
−(R−Y) input signal (pin 17) for saturated colour
−(B−Y) input signal (pin 18) for saturated colour
Input current during
Input resistance R
Internal DC voltage due to
Saturation control (pin 16)
Control voltage for
Control voltage for
Control voltage for
Minimum saturation V
Input current I
(G-Y) matrix
Matrixed according to the equation V
= 12,0 V; V
6-24
12, 13, 14(p-p)
= 1,0 V; V
15-24(p-p)
= 0,45 V; V
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
(pins 17, 18)
(peak-to-peak value) bar with 75% of
maximum amplitude
(peak-to-peak value) bar with 75% of
maximum amplitude
scanning I
clamping note 2 V
maximum saturation note 2 V
nominal saturation 6 dB below max.
note 2 V
−26 dB saturation
note 2 V
referred to maximum
= 1,8 V d 46 50 − dB
16
(G−Y)
= −0,51 V
(R−Y)
−0,19 V
17-24(p-p)
= V
P
P
V
17(p-p)
V
18(p-p)
17, 18
17, 18-24
17, 18
16
16
16
16
(B−Y)
= 1,05 V; V
6
10,8 12,0 13,2 V
− 100 130
− 1,05 1,48 V
− 1,33 1,88 V
−−1,0 µA
1,0 −−MΩ
3,8 4,4 4,8 V
4,0 4,2 4,4 V
2,9 3,1 3,3 V
1,9 2,1 2,3 V
−−20 µA
18-24(p-p)
= 1,33 V; T
= 25 °C;
amb
(1)
mA
Luminance input (pin 15)
Composite video input signal
(peak-to-peak value) V
Input resistance R
Input capacitance C
Input current during
scanning I
November 1987 7
15(p-p)
15-24
15-24
15
− 450 630 mV
100 −−kΩ
−−5pF
−−1µA
Page 8
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Linearity nominal settings m 0,85 −−
Internal DC voltage due
to clamping note 2 V
RGB channels
Signal switching input
(pin 11)
Normal state; no insertion V
Level for insertion-on V
Input capacitance C
Input current V
= 0 to 3 V I
11
Signal insertion
(pins 12, 13, 14)
External RGB input signals
(black-to-white value) V
Input current during
scanning I
Internal DC voltage due
to clamping notes 2, 3 V
Contrast control (pin 19)
note 2
Control voltage for
maximum contrast V
Control voltage for
nominal contrast 3 dB below max. V
Control voltage for
−10 dB below max. V
Minimum contrast
referred to max. V
Input current V
= 2V d 182129dB
19
> 6V I
25
Difference between
RGB channels contrast −10 dB
below max.
15
11
11
11-24
11
12, 13, 14
12, 13, 14
12, 13, 14
19
19
19
19
2,5 2,9 3,3 V
0 − 0,4 V
0,9 − 3,0 V
−−10 pF
−100 −+450 µA
− 1,0 1,4 V
−−1,0 µA
4,0 4,5 5,0 V
4,0 4,2 4,4 V
3,4 3,6 3,8 V
2,6 2,8 3,0 V
−−2µA
−−0,6 dB
Peak beam current limiting
(pin 25)
Internal DC bias voltage note 2 V
Input resistance R
Input current at contrast
control input V
Brightness control (pin 20)
Control voltage range V
November 1987 8
= 4,5 V I
25
note 2
25
25-24
19
20
5,3 5,5 5,7 V
− 10 − kΩ
10 20 34 mA
1 − 3V
Page 9
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Input current −I
20
Change of black level in the
control range related to the
= 1 V −±50 − %
∆V
20
luminance signal (black/white)
Tracking 95 −−%
Internal signal limiting
(RGB)
Signal limiting referred to
nominal luminance and nominal
black level
black −−25 − %
white 115 120 125 %
White point adjustment
(pins 21, 22, 23) note 2
AC voltage gain note 4
V
V
V
Input resistance R
= 5,5 V G
21,22,23
= 0 V G
21,22,23
= 12 V G
21,22,23
V
V
V
21,22,23-24
RGB outputs
(emitter follower) (pins 1, 3, 5)
Output voltage; black-to-
white positive V
1,3,5
Black level without
automatic cut-off control note 2
= 10 V V
V
28,2,4
1,3,5
Difference in black level
between RGB channels due to
∆V
1,3,5
variation of contrast control
Cut-off control range note 2 V
Internal current source I
1,3,5
1,3,5
Automatic cut-off control
(pin 26) notes 2, 5
Input voltage range V
26
−−10 µA
− 100 − %
−35 −40 − %
+35 +40 − %
− 20 − kΩ
1,5 2,0 2,5 V
6,1 6,9 7,7 V
−−10 mV
4,0 4,6 − V
2,0 3,0 − mA
0 − 6,5 V
November 1987 9
Page 10
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Voltage difference between
cut-off current
measurement (note 6)
and leakage current
measurement (note 7) V
Input pin 26 switches to ground during horizontal flyback
Gain data
Voltage gain with respect
to luminance input
(pin 15) G
Frequency response of
luminance path 0 to 5 MHz d
Voltage gain with respect
to colour difference inputs
(pins 17 and 18)
Frequency response of
colour difference paths 0 to 2MHz d
Voltage gain with respect
to inserted signals G
Frequency response of
inserted signal paths 0 to 16 MHz d
Frequency response of
inserted signal paths 0 to 13 MHz d
Rise and fall times of RGB
output signals
(pins 1, 3, 5) t
Difference in transit times
between R, G and B channels ∆t
Delay time between signal
switching and signal insertion t
at nominal
brightness, contrast,
saturation and white
point settings
26
1,3,5-15
1,3,5-15
G
5-18
G
1-17
5-18
d
1-17
1-14
G
3-13
G
5-12
1-14
d
3-13
d
5-12
1-14
d
3-13
d
5-12
r,tf
1,3,5
d
TDA3507
0,5 0,64 0,72 V
14 16 18 dB
−−3dB
369dB
−−3dB
468dB
− 3 − dB
−−3dB
− 40 − ns
− 015ns
−25 −+25 ns
November 1987 10
Page 11
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT
Difference in gain between
normal mode and signal insertion
∆G
1,3,5
mode
Sandcastle pulse detector
(pin 10) note 8
Levels for separating the
following pulses:
horizontal and vertical
blanking pulses note 9 V
required pulses (H+V) V
horizontal pulses V
required pulses (H) V
clamping pulses note 10 V
required pulses V
no keying V
Input current −I
10
10
10
10
10
10
10
10
Notes
1. < 115 mA after warm-up.
2. Values are proportional to the supply voltage.
3. When V
< 0,4 V during clamping time the black levels of the inserted RGB signals are clamped on the black
11-24
levels of the internal RGB signals.
When V
> 0,9 V during clamping time the black levels of the inserted RGB signals are clamped on an internal
11-24
DC voltage (correct clamping of the external RGB signals is possible only when they are synchronous with the
sandcastle pulse).
4. When pins 21, 22 and 23 are not connected, an internal bias voltage of 5,5 V is supplied.
5. Automatic cut-off control measurement occurs in the following lines after start of the vertical blanking pulse:
line 12: measurement of leakage current (R + G+ B)
line 13: measurement of red cut-off current
line 14: measurement of green cut-off current
line 15: measurement of blue cut-off current
6. Black level of the measured channel is nominal; the other two channels are blanked to ultra-black.
7. All three channels blanked to ultra-black.
The cut-off control cycle occurs when the vertical blanking part of the sandcastle pulse contains more than 3 line
pulses.
The internal blanking continues until the end of the last measured line.
The vertical blanking pulse is not allowed to contain more than 34 line pulses, otherwise another control cycle begins.
8. The sandcastle pulse is compared with three internal thresholds (proportional to VP) and the given levels separate
the various pulses.
9. Blanked to ultra-black (−25%).
10. Pulse duration ≥ 3,5 µs.
−−10 %
1,0 1,5 2,0 V
2,1 2,5 2,9 V
3,0 3,5 4,0 V
4,1 4,5 5,0 V
6,5 7,0 7,5 V
7,6 − 12,0 V
−−1,0 V
−−110 µA
November 1987 11
Page 12
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
APPLICATION INFORMATION
TDA3507
(1) When supplied via a 75 Ω line.
(2) Capacitor value depends on circuit layout.
November 1987 12
Fig.3 Typical application circuit diagram using the TDA3507.
Page 13
Philips Semiconductors Product specification
Video control combination circuit with
automatic cut-off control
PACKAGE OUTLINE
handbook, full pagewidth
DIP28: plastic dual in-line package; 28 leads (600 mil)
D
seating plane
L
Z
28
e
b
TDA3507
SOT117-1
M
E
A
2
A
A
1
w M
b
1
15
c
(e )
1
M
H
pin 1 index
1
0 5 10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A
A
A
UNIT
inches
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
max.
mm
1 2
min.
max.
b
1.7
1.3
0.066
0.051
b
0.53
0.38
0.020
0.014
cD E weM
1
0.32
0.23
0.013
0.009
(1) (1)
36.0
35.0
1.41
1.34
14.1
13.7
0.56
0.54
E
14
(1)
L
3.9
3.4
M
15.80
15.24
0.62
0.60
H
E
17.15
15.90
0.68
0.63
0.252.54 15.24
0.010.10 0.60
e
1
0.15
0.13
Z
max.
1.75.1 0.51 4.0
0.0670.20 0.020 0.16
OUTLINE
VERSION
SOT117-1
November 1987 13
SOLDERING
REFERENCES
IEC JEDEC EIAJ
051G05 MO-015AH
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-01-14
Page 14
Philips Semiconductors Product specification
Video control combination circuit with
TDA3507
automatic cut-off control
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and
surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for
surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often
used.
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our
“IC Package Databook”
Soldering by dipping or by wave
The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the
joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
be necessary immediately after soldering to keep the temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more
than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to
10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds.
(order code 9398 652 90011).
). If the printed-circuit board has been pre-heated, forced cooling may
stg max
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
November 1987 14
Loading...