Page 1
INTEGRATED CIRCUITS
DATA SH EET
TDA1553CQ
2 × 22 W stereo BTL car radio
power amplifier with loudspeaker
protection and 3-state mode switch
Product specification
Supersedes data of July 1994
File under Integrated Circuits, IC01
1996 Jan 07
Page 2
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection
TDA1553CQ
FEATURES
• Few peripheral components
• High output power
• Low output offset voltage
• Fixed gain
• High energy handling capability at the outputs (V
• Electrostatic discharge protection
• No switch-on/switch-off plop
• Flexible leads
• Low thermal resistance.
P
• Loudspeaker protection
• Good ripple rejection
• 3-state mode switch (operating, mute, standby)
• Load dump protection
• AC and DC short-circuit safe to ground and to V
• Thermally protected
P
GENERAL DESCRIPTION
The TDA1553CQ is a monolithic integrated class-B output
amplifier in a 13-lead plastic DIL-bent-SIL power package.
It contains 2 × 22 W amplifiers in BTL configuration.
The device is primarily developed for car radio
applications.
• Reverse polarity safe
QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
P
positive supply voltage
operating 6 14.4 18 V
non-operating −−30 V
load dump −−45 V
I
ORM
I
q
I
stb
|Z
| input impedance 50 −−kΩ
i
T
vj
repetitive peak output current −−4A
total quiescent current − 80 − mA
standby current − 40 100 µA
virtual junction temperature −−150 °C
Stereo application
P
O
SVRR supply voltage ripple rejection R
| DC output offset voltage −−150 mV
|∆V
O
α
cs
|∆G
| channel unbalance −−1dB
v
output power at 4 Ω; THD = 10% − 22 − W
=0Ω; f = 100 Hz to 10 kHz 48 −−dB
s
channel separation 40 −−dB
=0)
ORDERING INFORMATION
TYPE
NUMBER
NAME DESCRIPTION VERSION
TDA1553CQ DBS13P plastic DIL-bent-SIL power package; 13 leads (lead length 12 mm) SOT141-6
1996 Jan 07 2
PACKAGE
Page 3
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
BLOCK DIAGRAM
handbook, full pagewidth
input 1
1
2
kΩ
18 kΩ
mute switch
VA
mute switch
C
m
C
m
power stage
V
P1
3
TDA1553CQ
PROTECTIONS
Load dump
Soar
Thermal
Short - circuit
Reverse polarity
Loudspeaker
V
10
TDA1553CQ
P2
4
output 1A
input 2
6
11
12
9
output 1B
mode switch
loudspeaker
protection
output 2B
18 kΩ
stand-by
switch
VA
x1
18 kΩ
VA
V
P
15 kΩ
15 kΩ
mute switchVAC
mute switch
mute
reference
voltage
C
power stage
stand-by
reference
voltage
mute
switch
m
power stage
m
3-state
interface
loudspeaker
protection
60
kΩ
13
2
kΩ
2
kΩ
1996 Jan 07 3
60
kΩ
input
reference
voltage
VA
2
kΩ
18 kΩ
258
GND1 GND2
ground (signal)
power ground (substrate)
power stage
Fig.1 Block diagram.
MBC991 - 1
7
output 2A
Page 4
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
TDA1553CQ
PINNING
SYMBOL PIN DESCRIPTION
IN1 1 input 1
GND(S) 2 signal ground
V
P1
3 supply voltage
OUT1A 4 output1A
GND1 5 power ground1
OUT1B 6 output1B
OUT2A 7 output2A
GND2 8 power ground2
OUT2B 9 output2B
V
P2
10 supply voltage
MODE 11 mode switch input
LSP 12 loudspeaker protection
IN2 13 input 2
handbook, halfpage
GND(S)
OUT1A
IN1
V
P1
GND1
1
2
3
4
5
FUNCTIONAL DESCRIPTION
The TDA1553CQ contains two identical amplifiers with
differential input stages and can be used for bridge
applications. The gain of each amplifier is fixed at 26 dB.
Special features of the device are:
3-state mode switch
• standby: low supply current (<100 µA)
• mute: input signal suppressed
• operating: normal on condition.
Loudspeaker protection
When a short-circuit to ground occurs, which forces a DC
voltage across the loudspeaker of ≥1 V, a built-in
protection circuit becomes active and limits the DC voltage
across the loudspeaker to ≤1V.
Pin 12 detects the status of the protection circuit (e.g. for
diagnostic purposes).
Short-circuit protection
If any output is short-circuited to ground during the standby
mode, it becomes impossible to switch the circuit to the
mute or operating condition. In this event the supply
current will be limited to a few milliamps.
OUT1B
OUT2A
OUT2B
GND2
V
P2
MODE
LSP
IN2
6
TDA1553CQ
7
8
9
10
11
12
13
MBC993
Fig.2 Pin configuration.
1996 Jan 07 4
Page 5
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
LIMITING VALUES
In accordance with the absolute maximum system (IEC 134).
SYMBOL PARAMETER CONDITION MIN. MAX. UNIT
V
P
I
OSM
I
ORM
T
stg
T
amb
T
vj
V
psc
V
pr
P
tot
positive supply voltage
operating − 18 V
non-operating − 30 V
load dump protection during 50 ms;
≥ 2.5 ms
t
r
non-repetitive peak output current − 6A
repetitive peak output current − 4A
storage temperature range −55 +150 °C
operating ambient temperature range −40 +85 °C
virtual junction temperature − 150 °C
AC and DC short-circuit safe voltage − 18 V
energy handling capability at outputs V
=0 − 200 mJ
P
reverse polarity − 6V
total power dissipation − 60 W
TDA1553CQ
− 45 V
THERMAL CHARACTERISTICS
In accordance with IEC 747-1.
SYMBOL PARAMETER VALUE UNIT
R
th j-a
R
th j-c
handbook, halfpage
thermal resistance from junction to ambient in free air 40 K/W
thermal resistance from junction to case (see Fig.3) 1.5 K/W
output 1 output 2
virtual junction
2.8 K/W
0.1 K/W
case
2.8 K/W
MBG799
Fig.3 Equivalent thermal resistance network.
1996 Jan 07 5
Page 6
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
DC CHARACTERISTICS
V
= 14.4 V; T
P
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
V
P
I
q
Operating condition
V
11
I
11
V
O
|∆V
| DC output offset voltage −−150 mV
O
Mute condition
V
11
I
11
V
O
| DC output offset voltage −−150 mV
|∆V
O
standby condition
|I11| mode switch 3-state leakage current −−10 µA
I
stb
Loudspeaker protection
| or
|∆V
4-6
|∆V
|
7-9
Protection active (|∆V
I
12
V
12
Protection not active (|∆V
V
12
=25°C; measured in Fig.4; unless otherwise specified.
amb
positive supply voltage note 1 6 14.4 18 V
quiescent current
R
= ∞−80 160 mA
L
note 2 − 5.5 − mA
mode switch voltage level 2.2 − 7V
mode switch current V11= 2.2 V − 50 100 µA
DC output voltage note 3 − 6.9 − V
mode switch voltage level 0 − 0.6 V
mode switch current V11= 0.6 V − 50 100 µA
DC output voltage note 3 − 6.9 − V
standby current I11=0µA − 40 100 µA
DC voltage across R
| or |∆V
4-6
| ≥ 1.0 V)
7-9
L
−−1V
current information − 25 −µA
voltage information 3.6 −−V
| and |∆V
4-6
|≤0.15 V)
7-9
voltage information −−0.3 V
TDA1553CQ
Notes
1. The circuit is DC adjusted at V
2. If any output is short-circuited to ground during the standby mode and in this condition the circuit is switched to mute
or operating condition.
3. At 18 V < VP< 30 V the DC output voltage ≤VP/2.
1996 Jan 07 6
= 6 to 18 V and AC operating at VP= 9 to 18 V.
P
Page 7
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
AC CHARACTERISTICS
V
= 14.4 V; RL=4Ω; f = 1 kHz; T
P
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
P
O
output power VP= 14.4 V
THD total harmonic distortion P
P
O
output power VP= 13.2 V
B power bandwidth THD = 0.5%; P
f
l
f
h
G
v
low frequency roll-off at −1 dB; note 1 − 25 − Hz
high frequency roll-off at −1 dB 20 −−kHz
closed loop voltage gain 25 26 27 dB
SVRR supply voltage ripple
rejection
on 48 −−dB
mute 48 −−dB
standby 80 −−dB
| input impedance 50 60 75 kΩ
|Z
i
V
no
noise output voltage note 3
on R
on R
V
no
noise output voltage notes 3 and 4
mute − 60 −µV
α
cs
| channel unbalance −−1dB
|∆G
v
V
O
channel separation RS=10kΩ 40 −−dB
output voltage in mute note 5 −−2mV
=25°C; measured in Fig.4; unless otherwise specified.
amb
THD = 0.5% 15 17 − W
THD = 10% 20 22 − W
=1W − 0.1 − %
O
THD = 0.5% − 12 − W
THD = 10% − 17 − W
= −1 dB;
O
− 20 to
with respect to 15 W
note 2
=0Ω−70 120 µV
S
=10kΩ−100 −µV
S
15000
TDA1553CQ
− Hz
Notes
1. Frequency response externally fixed.
2. Ripple rejection measured at the output with a source-impedance of 0 Ω, maximum ripple amplitude of 2 V (p-p) and
at a frequency between 100 Hz and 10 kHz.
3. Noise measured in a bandwidth of 20 Hz to 20 kHz.
4. Noise output voltage independent of R
5. VI=V
= 1 V RMS.
Imax
1996 Jan 07 7
S(VI
= 0 V).
Page 8
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
APPLICATION INFORMATION
TDA1553CQ
handbook, full pagewidth
loudspeaker
(1)
input 1
ground (signal)
input 2
protection
220 nF
220 nF
mode switch
4.7 µF
12 11 3 10
1
60
kΩ
2
TDA1553CQ
13
60
kΩ
reference
voltage
V
P
100
nF
4
RL = 4 Ω
6
9
RL = 4 Ω
2200
µF
14.4 V
58
power ground (substrate)
(1) With C = 4.7 µF the delay time of the loudspeaker protection is typically 0.5 s.
Fig.4 Stereo BTL application diagram.
1996 Jan 07 8
7
MBC992 -1
Page 9
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
PACKAGE OUTLINE
TDA1553CQ
DBS13P: plastic DIL-bent-SIL power package; 13 leads (lead length 12 mm)
non-concave
x
D
E
h
view B: mounting base side
d
B
j
A
SOT141-6
D
h
2
E
A
113
e
Z
DIMENSIONS (mm are the original dimensions)
UNIT A e
mm
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT141-6
A2bpcD
17.0
4.6
4.2
0.75
0.60
15.5
1
e
(1)
deD
0.48
24.0
23.6
20.0
19.6
0.38
IEC JEDEC EIAJ
b
p
h
10 3.4
w M
0 5 10 mm
(1)
E
12.2
11.8
REFERENCES
scale
1
1.7
e
5.08
L
3
L
E
2
h
6
Q
c
m
LL3m
3.4
12.4
3.1
11.0
e
2
2.4
1.6
PROJECTION
Qj
2.1
4.3
1.8
EUROPEAN
v M
v
0.8
x
0.25w0.03
ISSUE DATE
92-11-17
95-03-11
(1)
Z
2.00
1.45
1996 Jan 07 9
Page 10
Philips Semiconductors Product specification
2 × 22 W stereo BTL car radio power
amplifier with loudspeaker protection and
TDA1553CQ
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“IC Package Databook”
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
(order code 9398 652 90011).
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
stg max
). If the
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1996 Jan 07 10
Loading...