Datasheet T-51410D104J-FW-P-AC Datasheet (OPTREX)

Page 1
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 1/25
LCD Module Technical Specification
T-51410D104J-FW-P-AC
NO. ITEM PAGE
-
Contents 1
1
Application 2
2
Features 2
3
4
Mechanical Drawing of TFT-LCD module 3
5
Input / Output Terminals 4
6
Absolute Maximum Ratings 6
7
Electrical Characteristics 6
8
Power On Sequence 12
9
Optical Characteristics 13
10
Handling Cautions 16
11
Reliability Test 17
12
Indication of Label 17
13
Block Diagram 18
14
Standard 19
15
Packing 24
-
Revision History 25
Checked by (ACI Engineering Div.)
Checked by (Quality Assurance Div.)
Approved by (Production Div.)
Prepared by (Production Div.)
Type No.
Oct 8, 2002
OPTREX
First Edition
Final Revision
******
Page 2
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 2/25
1.Application
This data sheet applies to a color TFT LCD module, T-51410D104J-FW-P-AC. T-51410D104J-FW-P-AC module applies to notebook PC, sub-note-book PC and other OA
product, which require high quality flat panel display.
This module is not designed for aerospace, avionics, medical, F/A, transportation, car or any other products, which require extreme level of reliability.
Prime View assume no responsibility for any damage resulting from the use of the device which dose not comply with the instructions and the precautions in these specification sheet.
2. Features
. Amorphous silicon TFT LCD panel with back-light unit . Pixel in stripe configuration . Slim and compact, designed for O/A application . Display Colors:262,144 colors . Optimum Viewing Direction:6 o’clock . 3.3V LVDS interface standard: DS90CF364 as receiver . +3.3V DC supply voltage for TFT LCD panel driving . Backlight driving DC/AC inverter not included in this module .Long Life Lamp
3.Mechanical Specifications
Parameter Specifications Unit
Screen Size 26.4(diagonal) cm
10.4 (diagonal) inch
Display Format
800× (R, G, B)×600
dot
Display Colors 262,144 Active Area
211.2(H)×158.4 (V)
mm
Pixel Pitch
0.264 (H)×0.264 (V)
mm
Pixel Configuration Stripe Outline Dimension
238.6 (w)×171.0(H)×6.0(typ.) (D)
mm
Weight 310(typ.),320(max.) g Back-light Single CCFL, side-light type Surface treatment Anti-glare and hard-coating Display mode Normally white
Page 3
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 3/25
4. Mechanical Drawing of TFT-LCD Module
Unit: mm
Page 4
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 4/25
5. Input Terminals
5-1) TFT-LCD Panel Driving Connector type: Molex 55177-1491
Pin No. Symbol Function Remark
1 VDD Power supply : +3.3V 2 VDD Power supply : +3.3V 3 GND 4 GND 5 IN0- Pixel data Transmission pair 0 (negative -) 6 IN0+ Pixel data Transmission pair 0 (positive +) 7 IN1- Pixel data Transmission pair 1 (negative -) 8 IN1+ Pixel data Transmission pair 1 (positive +) 9 IN2- Pixel data Transmission pair 2 (negative -)
10 IN2+ Pixel data Transmission pair 2 (positive +)
11 CLK- Sampling Clock (negative -) 12 CLK+ Sampling Clock (positive +) 13 GND 14 GND
Recommended Transmitter (DS90C*363 of National Semiconductor) to T-51410D104J-FW-P-AC interface Assignment:
Input terminal of DS
90C*363
Graphic controller output signal
Output signal
symbol
To T-51410D104J-
FW-P-AC
Interface
terminal(Symbol)
Symbol No. Symbol Function
TIN0 44 R0 Red pixel data (LSB) TIN1 45 R1 Red pixel data TIN2 47 R2 Red pixel data Tout0- No.5 : IN0­TIN3 48 R3 Red pixel data TIN4 1 R4 Red pixel data Tout0+ No.6 : IN0+ TIN5 3 R5 Red pixel data(MSB) TIN6 4 G0 Green pixel data (LSB) TIN7 6 G1 Green pixel data TIN8 7 G2 Green pixel data
TIN9 9 G3 Green pixel data Tout1- No.7 : IN1­TIN10 10 G4 Green pixel data TIN11 12 G5 Green pixel data(MSB) Tout1+ No.8 : IN1+ TIN12 13 B0 Blue pixel data(LSB) TIN13 15 B1 Blue pixel data TIN14 16 B2 Blue pixel data TIN15 18 B3 Blue pixel data TIN16 19 B4 Blue pixel data Tout2- No.9 : IN2­TIN17 20 B5 Blue pixel data(MSB) TIN18 22 NC No connection Tout2+ N0.10 : IN2+ TIN19 23 NC No connection TIN20 25 ENAB Compound Synchronization signal
CLK in 26 NCLK Data sampling clock TCLK out-
TCLK out+
No.11 : CLK IN­ No.12 : CLK IN+
Page 5
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 5/25
Data stream of IN0-/+, IN1-/+ and IN2-/+ for T-51410D104J-FW-P-AC
LVDS Interface Block Diagram
Graphic Controller Circuit
TIN0~TIN5 TIN6~TIN11 TIN12~TIN17
TIN18 TIN19 TIN20
TCLK IN
R0~R5 G0~G5 B0~B5
NC NC ENAB
CLK IN
TTL parallel to LVDS
PLL
DS90C*363
LVDS to TTL parallel
PLL
DS90CF364
IN0­IN0+
RxOUT0~RxOUT5 RxOUT6~RxOUT11 RxOUT12~RxOUT17
RxOUT18 RxOUT19 RxOUT20
CLK OUT
LCD Internal Circuit
IN1­IN1+
IN2­IN2+
CLK­CLK+
T-51410D104J-FW-P-AC module side
Customer system side
5-2) Backlight driving Connector type : “BHR-02VS-1” of Japan Solderless Terminal MFG Co. LTD
PIN NO. Symbol Description Remark
1 VL1 Input Voltage(High) 2 VL2 Input Voltage(Low)
RxOUT6 RxOUT5 RxOUT4 RxOUT3 RxOUT2
RxOUT1
RxOUT0
G0
R5
R4 R3 R2
R1 R0
IN0
RxOUT13 RxOUT12 RxOUT11 RxOUT10 RxOUT9
RxOUT8
RxOUT7
B1
B0
G5 G4 G3
G2 G1
IN1
RxOUT13 RxOUT12 RxOUT11 RxOUT10 RxOUT9
RxOUT8
RxOUT7
ENAB
NC
NC
B5 B4
B3 B2
IN2
Page 6
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 6/25
6. Absolute Maximum Ratings:
GND=0V, Ta=25°C
Parameters Symbol MIN. MAX. Unit Remark
Supply Voltage VDD -0.3 +4.0 V Input Signals Voltage V
IN
-0.3 VDD+0.3 V Note 6-1
Backlight Driving Voltage V
L
- 2000 V
Backlight Driving Frequency F
L
0 100 KHz
Storage Temperature T
ST
-20 +70
°C
Note 6-2
Operating Temperature T
OP
0 +60
°C
Note 6-1: LVDS signal Note 6-2: Humidity : 90% RH Max. at Ta 40
Maximum wet-bulb temperature is at 39,or less at Ta > 40,and no condensation.
7. Electrical Characteristics
7-1) Recommended Operating Conditions: GND = 0V ,Ta = 25°C
Item Symbol Min. Typ. Max. Unit Remark
Supply Voltage VDD 3.0 3.3 3.6 V
Current Dissipation I
DD
- 350 450 mA Note 7-1 LVDS Differential input high threshold VTH - - 100 mV Note 7-2 LVDS Differential input low threshold VTL -100 - - Lamp Current I
FL
3.0 5.0 6.0 mA 5mA : 160 cd/m2 Note 7-3 Note 7-5
Lamp Voltage V
L
500 550 600 Vrms IFL=5mA
Note 7-3
Lamp Initial Voltage V
SFL
- 1200 - Vrms
at Ta=25°C
1000
at Ta=0 °C
Lamp Driving Frequency F
L
- 45 - KHz
Total power consumption (at IFL=5mA) -- 3.91 - W Note 7-4
Note 7-1: To test the current dissipation of VDD, using the “color bars” testing pattern shown
as below.
1234567
8
1.
White
2.
Yellow
3.
Cyan
4.
Green
5.
Magenta
6.
Red
7.
Blue
8.
Black
Idd current dissipation testing pattern
Page 7
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 7/25
Note 7-2: Please refers to DS90CF364 specification by National Semiconductor Corporation.
This LCD module conforms to LVDS standard. Note 7-3: The back-light driving waveform should be as closed to sine-wave as possible. In order to satisfy the quality of B/L , no matter use what kind of inverter , the output lamp current must between Min. and Max. to avoid the abnormal display imagecaused by B/L.
Note 7-4: Not including the efficiency of backlight DC/AC inverter Note 7-5: Lamp current is measured with current meter for high frequency as shown below
Inverter
TFT-LCD Module
~ A
1 2
* Pin 2 is V
low
** Current meter :
Yokogawa 2016-01
7-2) Input / Output signal timing chart (A) Vertical Timing
X,1X,2X,3X,4X,598X,599X,600X,
Y
t1 t2
t
3
t
3
CLK
ENAB
R5 ~R0 G5 ~G0 B5 ~B0
Lamp current dissipation testing configuration
Page 8
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 8/25
(B) Horizontal Timing
t
3
t
4
t
c
CLK
ENAB
R5~R0 G5~G0 B5~B0
1,Y2,Y3,Y4,Y5,Y6,Y7,YX,Y798,Y 800,
Y
797,Y 799,
Y
CLK
t6
t7
t5
VIH(Min):0.8Vcc
VIL(Max):0.2Vcc
ENAB
R5-R0 G5-G0 B5-B0
VALID
DATA
InputSignal
CenterLevel:
0.5Vcc
VIH(Min):0.8Vcc
VIL(Max):0.2Vcc
CLK
a
b
0.5Vcc
Duty(a,b):50±10%
t8 t9
Page 9
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 9/25
D) Timing Specifications
Item Symbol Min. Typ. Max. Unit Remark
Frame Cycling t1
604×t3 628×t3 660×t3
-
- 16.58 17.86 ms
Vertical Display Period t2
600×t3 600×t3 600×t3
-
Horizontal Scanning Time t3
844×t5 1056×t5 1064×t5
-
26.3 26.4 -
μs
Horizontal Display Period t4 -
800×t5
- ­Clock Cycle t5 24.0 25.0 - ns Clock High Level Time t6 9.0 - - ns Clock Low Level Time t7 9.0 - - ns Hold time t8 4.0 - - ns Set-up time t9 5.0 - - ns
Page 10
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 10/25
7-3) Display Color and Gray Scale Reference
Input Color Data
Color Red Green Blue
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Basic Blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Colors Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Red (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Red (02) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Darker
Red
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Brighter Red (61) 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Green (02) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
Darker
Green
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Brighter Green (61) 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 Green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 Green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Blue (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Blue (02) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Darker
Blue
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
Brighter Blue (61) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 Blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 Blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Page 11
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 11/25
7-4) Pixel Arrangement
The LCD module pixel arrangement is the stripe.
RGBRGBRGBRGBRGBRG
B
RGBRGBRGBRGBRGBRGBRGBRGB3
rd Line
2nd Line1
st Line
600th Line599th Line598th LineRGBRG
B
RGB
RGB1st Pixel800th Pixel1 Pixel =RGB
Page 12
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 12/25
8.Power On Sequence
1. The supply voltage for input signals should be same as V
CC.
2. When the power is off , please keep whole signals (Hsync, Vsync, CLK, Data) low level or high impedance
3.0V
3.0V
0s<t<35ms
0s<t<35ms
2t1 0<t1
Signal
Backlight
VCC
Page 13
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 13/25
9. Optical Characteristics
9-1) Specification:
Ta = 25°C
Parameter Symbol Condition MIN. TYP. MAX. Unit Remarks
Horizontal θ ±
35
±
45
- deg
θ
(to 12
o’clock)
10 15 - deg Note 9-1
Viewing Angle
Vertical
θ
(to 6
o’clock)
CR≥10
25 40 - deg
Contrast Ratio CR
Optimum
direction
100 180 - - Note 9-2
Rise Tr - 15 50 ms
Response time
Fall Tf
θ=0°
ϕ=0°
- 25 50 ms
Note 9-4
Luminance L θ=0°/ϕ=0° 130 160 - cd/m2IFL=5mA, Note 9-3 Luminance Uniformity U 55 80 - % Note 9-5
x 0.260 0.310 0.360 ­y 0.290 0.340 0.390 -White Chromaticity
Tc 6400 6600 6800 K Lamp Life Time 30000 40000 - hr IFL=5mA Cross Talk Ratio CTK - - 3.5 % Note 9-6
All the optical measurement shall be executed 30 minutes after backlight being turn-on. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure.
Photometer (TOPCON BM-5A or BM-7 fast)
500 mm +/- 50 mm
TFT-LCD module
DC/AC Inverter
Optical characteristics measuring configuration
Field = 2°
Page 14
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 14/25
Note 9-1’: The definitions of viewing angles are as follows.
12 o’clock
3 o’clock
9 o’clock
6 o’clock
θ
φ
Lamp connector
Note 9-2: The definition of contrast ratio
0 levelgray at Luminance
63 levelgray at Luminance
CR =
Note 9-3: Topcon BM-5A luminance meter 2° field of view is used in the testing (after 30 minutes’
operation). The typical luminance value is measured at lamp current 3.0 mA. The max luminance value is measured at lamp current 6.0 mA.
Note 9-4: Definition of Response Time Tr and Tf:
100%
90%
10%
0%
White White
Brightness
Black
TrT
f
Note 9-5: The uniformity of LCD is defined as
The Minimum Brightness of the 9 testing Points
U =
The Maximum Brightness of the 9 testing Points Luminance meter : BM-5A or BM-7 fast(TOPCON) Measurement distance : 500 mm +/- 50 mm Ambient illumi nation : < 1 Lux Measuring direction : Perpendicular to the surface of module
Page 15
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 15/25
The test pattern is white (Gray Level 63).
25% 50% 75%
25%
50%
75%
YA-YB
Note 8-6: Cross Talk (CTK) =
YA
×100%
YA: Brightness of Pattern A YB: Brightness of Pattern B Luminance meter: BM 5A (TOPCON) Measurement distance: 500 mm +/- 50 mm Ambient illumination: < 1 Lux Measuring direction: Perpendicular to the surface of module
Pattern A
(Gray Level 31)
Pattern B
(Gray Level 31, central
black box exclusive)
: Measuring Point (A and B are at the same point.)
YA
YB
1/3 1/3 1/3
1/3 1/3 1/3
Black
(Gray Level 0)
Page 16
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 16/25
10. Handling Cautions 10-1) Mounting of module
a) Please power off the module when you connect the input/output connector. b) Please connect the ground pattern of the inverter circuit surely. If the connection is not perfect, some following problems may happen possibly.
1.The noise from the backlight unit will increase.
2.The output from inverter circuit will be unstable.
3.In some cases a part of module will heat. c) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. d) Protective film (Laminator) is applied on surface to protect it against scratches and dirts. It is recommended to peel off the laminator before use and taking care of static electricity.
10-2) Precautions in mounting
a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled,
wipe it with soft dry cloth.
b) Wipe off water drops or finger grease immediately. Long contact with water may
cause discoloration or spots.
c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped
on hard surface. Please handle with care.
d) Since CMOS LSI is used in the module. So take care of static electricity and
earth yourself when handling.
10-3) Adjusting module
a) Adjusting volumes on the rear face of the module have been set optimally before
shipment.
b) Therefore, do not change any adjusted values. If adjusted values are changed,
the specifications described may not be satisfied.
10-4) Others
a) Do not expose the module to direct sunlight or intensive ultraviolet rays for many
hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because
of leakage current from approach conductor by to draw lump read lead line around.
d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel.
Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes
or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic
components.
f) Please adjust the voltage of common electrode as material of attachment by 1
module.
Page 17
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 17/25
11. Reliability Test
No Test Item Test Condition Remark
1 High Temperature Storage Test
Ta = +70°C, 240 hrs
2 Low Temperature Storage Test
Ta = -20°C, 240 hrs
3 Low Temperature Operation Test
Ta = 0°C, 240 hrs
4
High Temperature & High Humidity Operation Test
Ta = +60°C, 80%RH, 240 hrs (No Condensation)
5
Thermal Cycling Test (non-operating)
0°C ßà+25°C ßà+60°C, 50 Cycles 1Hr 0.5Hr 1Hr
6
Vibration Test (non-operating)
Frequency:10∼57 H
Z ,
Amplitude: 0.15 mm
58∼500Hz, 1G
Sweep time: 11 min Test Period: 3 hrs(1 hr for each direction of X, Y, Z)
7
Shock Test (non-operating)
80G, 6ms, X,Y, Z 1 times for each direction
Ta: ambient temperature
[Judgement Criteria]
Under the display quality test conditions with normal operation state , there should be no change which may affect practical display function.
12. Indication of Label
a) Indicated contents of the label
Lot number
Products number Contents of lot number : 1st—Process area : class 1000 H
class 100K M 2nd~3rd—Module screen size(in inch) : 1.8”18, 2.5”⇒25…… 5th—Production year : 19999, 2000A, 2001⇒1…….. 6th—Production month : 1, 2, 3,….9, A, B, C
7th~10th—Serial numbers : 0001~9999
b) Indicated contents of the Product number label
T-51382D064J-FW-P-AC MADE IN TAIWAN

XXXXXXXXXXXXXXXXXXXXX
Module Name of Optrex
Ex. T-51382D064J-FW-P-AC
Barcode Symbol
Barcode Number
Production Country
The Module Manufacture Location
OOO-OOOOOO
OD104SL3XX
Page 18
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 18/25
13. Block Diagram
123
599598600
4212400
Control Circuit
EN A B C LK
IN0-/ + IN1-/ +
IN2-/ +
TFT-LCD
Display Area
B ack-l ig h t(L a m p 1 )
VL1 VL2
3
S ource D ri v e r
G
ate
Dr
i
v
e
r
LVDS Interface (DS90C364)
Pow e r M odule
V DD
E N A B C L K
R 0 R 1
G 0 G 1 1
B 0 B 1
R 5
G 5
B 5
Page 19
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 19/25
14. Standard
14-1) Inspection condition
Viewing Angle (Major axis x)
θ < 45° inspection under non-operating condition θ < 5° inspection under operating condition
TFT-LCD Module
Back-Light Unit
35cm or more
Viewing Zone
14-2) Environment condition
Ambient Temperature: 25°C ±5°C
Ambient Humidity: 65±5%RH
Ambient Luminance: 20 watts fluorescent lamp (about 500 lux)
14-3) Sampling condition
Unless otherwise agreed in written, the sampling inspection shall be applied to the incoming inspection of customer.
Lot size: Quantity of shipment lot per model.
Sampling type: Normal inspection, single sampling
Sampling Level: Level II
Sampling table: ISO 2859 (Also known as MIL-STD-105E).
14-4) Acceptance Quality Level (AQL)
The AQL for major and minor defects is defined as follows:
Major defect: 0.65%
Minor defect: 1.5%
14-5) Classification of defects
Defects and classified as either a major or minor defect defined as bellows:
Major defect: It is a defect that is likely to result in failure or to reduce materially the usability of the product for the intended function.
M inor defect:
Page 20
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 20/25
It is a defect that will not result in functioning problem with deviation classified.
14-6) Inspection Instrument:
DC Power supply: DC 12V
Luminance color meter: Topcon BM –7
Others: Micrometer, Microscope, and Caliper.
Page 21
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 21/25
14-7) Cosmetic Specification
Item Specification/Description Classification Note
Display function
No Display
Malfunction
Major
Flickering Visible at display area Minor
Contrast ratio
(Black, White)
Does not meet specified
range in the spec.
Major
Line defect
Vertical and Horizontal Line defect in bright, dark
Major
Point defect (Red, Green, Blue, Dark)
Minor 1
Image retention
After displaying fixed pattern for 30 minutes, the afterimage is visible after 10 seconds.
Minor
Display
Inspection
(operating)
Non-uniformity
Visible through 2 % ND Filter.
Minor
Dimension Outline Major
Bezel appearance
Out of mechanical spec regarding bending area.
Minor
Scratch on the polarizer
N=5 max (W0.1 or L≤10) N=0 (W>0.1 or L>10)
Minor 2
Dent or Bubble on the polarizer ( in available viewing area )
N=5 max (W0.5 and L≤10) N=0 (W>0.5 or L>1.0)
Minor 2
Foreign material on polarizer
(W >1/4L) N=4 max (0.1L<D≤0.4)
N disregard (W ≤1/4L) N=4 max (0.03 <W≤0.10 and 0.3<L ≤2.1)
N=0 (W>0.1orL>2.1)
Minor 3
Plastic frame Break or modification Minor 2
External
Inspection
(non-operating)
Wrinkle on polarizer
Serious wrinkle is not allowed
Item Number Total
Bright
(Green)
3
Bright 10
10
12
Page 22
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 22/25
Cable The metal wire is exposed Minor 2 Connector (signal input)
Break Major
(W-Width in mm, L-Length in mm, N-Number, D-Average Diameter in mm,) Remark: Major: Defect that is likely to result in failure or to reduce materially the usability of the product for the intended function.
Minor: Defect that will not result in functioning problem with deviation as classified.
Page 23
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 23/25
Note: 1. (a) Bright point defect is defined as point defect of R, G, B with area >1/2 pixel
Respectively and is not visible by using 5% ND filter.
(b) Definition of distribution of point defect is as follows:
within 20mm diameter, it is allowed 4 dark points or 3 bright and dark points max.
(c) Definition of joined bright point defect is as follows:
-Three joined bright point must be nil.
-Joined bright point is 3 pairs maximum.
(d) Definition of joined dark point defect is as follows:
-Three jointed dark point must be nil.
-Coupling of one dark and one bright point in junction is counted as one dark and one bright spot.
-Two dark point in junction is counted as one dark point.
Note: 2. The external inspection is conducted at the distance 30cm minimum between the
eyes of inspector and the panel. The inspection area is defined as full screen.
Note: 3. W: Width of foreign material
L: Length of foreign material (Take larger value of L1 and L2)
4A:
Page 24
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 24/25
15. Packing
Page 25
T-51410D104J-FW-P-AC (AC) No. 2002-0203 OPTREX CORPORATION Page 25/25
Revision History
Rev. Issued Date Revised Content
1.0 Apr. 03, 2002 New
1.1 Jun. 03, 2002 Add
Page 18 : Indication of Lot Number Label
Loading...