Page 1
ALUMINUM ELECTROLYTIC CAPACITORS
WITH CONDUCTIVE POLYMER SOLID ELECTROLYTE
Super low E.S.R. and high ripple current are realized.
y
Guarantees 105ƫ,2000 hours .
y
PVX
ɜ SPECIFICATIONS
Item Performance
Category temperature range (ƫ) 55~+105
Tolerance at rated capacitance (%)
Leakage current (PA)
*Note
Tangent of loss angle (tan G)
Characteristics at high
and low temperature
Endurance (105ƫ)
(Applied ripple current)
Bias Humidity
60
ƫ, 90 to 95%
Characteristics of applied
surge voltage
Failure tare
*Note: If any doubt arises, measure the leakage current after following voltage application treatment.
Voltage application treatment: DC rated voltage are appliced to the capacitors for 120 minutes at
RH
CĈRated capacitance (PF)ćVĈRated voltage (V) (20ƫ)
Less than 0.12 (20ƫ, 120Hz)
Impedance ratio (max.)
Z25ƫ/Z+20
Z55ƫ/Z+20
Test time 2000 hours
Leakage current The initial specified value or less
Percentage of capacitance change
Tangent of the loss angle 150% or less of the initial specified value
E.S.R. change 200% or less of the initial specified value
Test time 500 hours
Leakage current The initial specified value or less
Percentage of capacitance change
Tangent of the loss angle 150% or less of the initial specified value
E.S.R. change 200% or less of the initial specified value
The capacitors shall be subject to 1000 cycles each consisting of charge with the surge voltage specified at 15 to 35
30 seconds through a protective resister (Rc = 1k:) in 6 minutes per cycle. Surge voltageŘ1.15 times of rated voltage.
Leakage current The initial specified value or less
Percentage of capacitance change
Tangent of the loss angle 150% or less of the initial specified value
E.S.R. change 200% or less of the initial specified value
1% per 1000 hours maxmum (Confidence level 60% at 105ƫ)
Less than 0.2CV
Within r20% of initial value
Within r20% of initial value
Within r20% of initial value
105
ƫ.
Marking colorĈBlack print
ƫ
r20 (20ƫ, 120Hz)
ƫŘ1.15
(120Hz)
ƫŘ1.25
ƫ for
ɜ OUTLINE DRAWING UnitȈmm
ID
L A B C W P Casing symbol
5 5.7 5.3 5.3 2.7 0.5 to 0.8 1.5 E60
6.3 5.7 6.6 6.6 2.7 0.5 to 0.8 2.0 F60
8 6.7 8.4 8.4 3.0 0.5 to 0.8 3.1 G70
10 7.7 10.4 10.4 3.3 0.7 to 1.1 4.7 H80
NOTE
Design, Specifications are subject to change without notice.
Ask factory for technical specifications before purchase and/or use.
23
Part numbering system (example: 4V150μF)
PVX – 4 V 151 M E60 –
Series code
Rated voltage
symbol
Rated capacitance
symbol
Capacitance
tolerance symbol
Casing
symbol
ș
Ta p i n g
symbol
Page 2
ALUMINUM ELECTROLYTIC CAPACITORS
WITH CONDUCTIVE POLYMER SOLID ELECTROLYTE
ɜ STANDARD RATINGS
PVX
Rated voltage (V)
Rated
capacitance (PF)
100
120
150
220
270
330
390
470
Item
2.5 4 6.3 10
Case ESR
IDuL
(mm)
ǕǕǕǕǕǕ
ǕǕǕǕǕǕǕǕǕ
5u5.7
5u5.7
5u5.7
ǕǕǕ
6.3u5.7
ǕǕǕ
m:
10 3800
10 3800
10 3800
Rated
ripple
current
mArms
6.3u5.7
9 4000
Case ESR
IDuL
(mm)
5u5.7
5u5.7
ǕǕǕǕǕǕǕǕǕ
ǕǕǕ
8u6.7
m:
10 3800
10 3800
Rated
ripple
current
mArms
6.3u5.7
9 4000
8 4300
Case ESR
IDuL
(mm)
5u5.7
5u5.7
ǕǕǕ
8u6.7
8u6.7
m:
15 3100
15 3100
Rated
ripple
current
mArms
9 4000
8 4300
8 4300
Case ESR
IDuL
(mm)
5u5.7
6.3u5.7
ǕǕǕ
8u6.7
8u6.7
ǕǕǕ
10u7.7
m:
15 3100
15 3200
10 3800
10 3800
10 4000
Rated
ripple
current
mArms
560
680
820
1000
1200
(Note) Rate ripple currentĈ105
8u6.7
8u6.7
ǕǕǕǕǕǕ
10u7.7
10u7.7
ƫ, 100kHz ; E.S.R.Ř20ƫ, 100kHz
8 4300
8 4300
8 4600
8 4600
8u6.7
10u7.7
10u7.7
ǕǕǕǕǕǕǕǕǕ
8 4300
8 4600
8 4600
ǕǕǕǕǕǕ
ǕǕǕǕǕǕ
10u7.7
ǕǕǕǕǕǕ
8 4600
ǕǕǕ
NOTE
Design, Specifications are subject to change without notice.
Ask factory for technical specifications before purchase and/or use.
24
Loading...