Datasheet ST730C16L3L, ST730C16L3, ST730C16L2L, ST730C16L1L, ST730C16L1 Datasheet (International Rectifier)

DISCRETE POWER DIODES and THYRISTORS

Next Data SheetIndex

Previous Datasheet

To Order

DATA BOOK

D-334

Bulletin I25191/B

Next Data SheetIndex

Previous Datasheet

To Order

ST730C..L SERIES

PHASE CONTROL THYRISTORS Hockey Puk Version

Features

Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AC (B-PUK)

Typical Applications

DC motor controls
Controlled DC power supplies
AC controllers

Major Ratings and Characteristics

Parameters ST730C..L Units

I

T(AV)

@ T

hs

I

T(RMS)

@ T

hs

I

TSM

2

I

t @ 50Hz 1591 KA2s

@ 50Hz 17800 A
@ 60Hz 18700 A

@ 60Hz 1452 KA

990 A

55 °C

2000 A

25 °C

990A

case style TO-200AC (B-PUK)

2

s

V

DRM/VRRM

t

q

T

J

800 to 1800 V

typical 150 µs

- 40 to 125 °C

D-335

ST730C..L Series

To Order

Next Data SheetIndex

Previous Datasheet

ELECTRICAL SPECIFICATIONS

Voltage Ratings

Voltage V

DRM/VRRM

Type number Code peak and off-state voltage repetitive peak voltage

08 800 900
12 1200 1300

ST730C..L 14 1400 1500 80

16 1600 1700
18 1800 1900

On-state Conduction

Parameter ST730C..L Units Conditions

I

Max. average on-state current 990 (375) A 180° conduction, half sine wave

T(AV)

@ Heatsink temperature 55 (85) °C double side (single side) cooled

I

Max. RMS on-state current 2000 DC @ 25°C heatsink temperature double side cooled

T(RMS)

I

Max. peak, one-cycle 17800 t = 10ms No voltage

TSM

non-repetitive surge current 18700 A t = 8.3ms reapplied

2

I

t Maximum I2t for fusing 1591 t = 10ms No voltage Initial TJ = TJ max.

2

I

√t Maximum I2√t for fusing 15910 KA2√s t = 0.1 to 10ms, no voltage reapplied

V

Low level value of threshold

T(TO)

1

voltage

V

High level value of threshold

T(TO)

2

voltage

r

Low level value of on-state

t1

slope resistance

r

High level value of on-state

t2

slope resistance

V

Max. on-state voltage 1.62 V Ipk= 2000A, TJ = TJ max, tp = 10ms sine pulse

TM

I

Maximum holding current 600

H

I

Typical latching current 1000

L

, max. repetitive V

, maximum non- I

RSM

DRM/IRRM

@ TJ = TJ max

V V mA

15000 t = 10ms 100% V
15700 t = 8.3ms reapplied Sinusoidal half wave,

1452 t = 8.3ms reapplied
1125 t = 10ms 100% V

KA2s

1027 t = 8.3ms reapplied

0.98 (16.7% x π x I
V

1.12 (I > π x I

T(AV)

0.32 (16.7% x π x I

mΩ

0.27 (I > π x I

mA

T(AV)

T

= 25°C, anode supply 12V resistive load

J

RRM

RRM

< I < π x I

T(AV)

),TJ = TJ max.

< I < π x I

T(AV)

),TJ = TJ max.

), TJ = TJ max.

T(AV)

), TJ = TJ max.

T(AV)

2222222222222

max.

12

Switching

di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, tr ≤ 1µs

t

d

t

q

Parameter ST730C..L Units Conditions

of turned-on current T

1000 A/µs

Typical delay time 1.0

Typical turn-off time 150

= TJ max, anode voltage ≤ 80% V

J

Gate current 1A, dig/dt = 1A/µs

= 0.67% V

V

d

µs

= 750A, TJ = TJ max, di/dt = 60A/µs, VR = 50V

I

TM

= 20V/µs, Gate 0V 100Ω, tp = 500µs

dv/dt

D-336

DRM, TJ

DRM

= 25°C

ST730C..L Series

To Order

Next Data SheetIndex

Previous Datasheet

Fig. 3 - Current Ratings Characteristics

Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics

Fig. 4 - Current Ratings Characteristics

Fig. 7 - Maximum Non-Repetitive Surge Current

Single and Double Side Cooled

Fig. 8 - Maximum Non-Repetitive Surge Current

Single and Double Side Cooled

D-340

Fig. 9 - On-state Voltage Drop Characteristics

To Order

Next Data SheetIndex

Previous Datasheet

ST730C..L Series

Fig. 10 - Thermal Impedance Z

Fig. 11 - Gate Characteristics

D-341

Characteristics

thJ-hs

Blocking

To Order

Next Data SheetIndex

Previous Datasheet

Parameter ST730C..L Units Conditions

dv/dt Maximum critical rate of rise of

off-state voltage

I

Max. peak reverse and off-state

DRM

I

leakage current

RRM

500 V/µs TJ = TJ max. linear to 80% rated V

80 mA TJ = TJ max, rated V

Triggering

Parameter ST730C..L Units Conditions

PGMMaximum peak gate power 10.0 TJ = TJ max, tp ≤ 5ms
P

Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50

G(AV)

I

Max. peak positive gate current 3.0 A TJ = TJ max, tp ≤ 5ms

GM

+V

Maximum peak positive

GM

gate voltage

-V

Maximum peak negative

GM

gate voltage

20

5.0

TYP. MAX.

DC gate current required

I

GT

to trigger

200 ­100 200

50 -

2.5 -

V

DC gate voltage required

GT

to trigger

I

DC gate current not to trigger 10 mA

GD

1.8 3.0

1.1 -

VGDDC gate voltage not to trigger 0.25 V

W

V

mA T

V T

T

T

T
T

T

T

= TJ max, tp ≤ 5ms

J

= - 40°C

J

= 25°C

J

= 125°C

J

= - 40°C

J

= 25°C

J

= 125°C

J

= TJ max

J

ST730C..L Series

DRM

applied

DRM/VRRM

Max. required gate trigger/ cur­rent/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied

Max. gate current/voltage not to
trigger is the max. value which
will not trigger any unit with rated
V

anode-to-cathode applied

DRM

23

Thermal and Mechanical Specification

T

J

T

stg

R

thJ-hs

R

thC-hs

F Mounting force, ± 10% 14700 N

wt Approximate weight 255 g

Parameter ST730C..L Units Conditions

Max. operating temperature range -40 to 125
Max. storage temperature range -40 to 150

Max. thermal resistance, 0.073 DC operation single side cooled
junction to heatsink 0.031 DC operation double side cooled

Max. thermal resistance, 0.011 DC operation single side cooled
case to heatsink 0.006 DC operation double side cooled

(1500) (Kg)

Case style TO - 200AC (B-PUK) See Outline Table

°C

K/W

K/W

D-3373333

ST730C..L Series

To Order

Next Data SheetIndex

Previous Datasheet

∆R

Conduction

thJ-hs

(The following table shows the increment of thermal resistence R

Conduction angle Units Conditions

180° 0.009 0.009 0.006 0.006
120° 0.011 0.011 0.010 0.011

90° 0.014 0.014 0.015 0.015 K/W T
60° 0.020 0.020 0.021 0.021
30° 0.036 0.036 0.036 0.036

Sinusoidal conduction Rectangular conduction

Single Side Double Side Single Side Double Side

when devices operate at different conduction angles than DC)

thJ-hs

= TJ max.

J

Ordering Information Table

Device Code

1 - Thyristor
2 - Essential part number
3 - 0 = Converter grade
4 - C = Ceramic Puk
5 - Voltage code: Code x 100 = V
6 - L = Puk Case TO-200AC (B-PUK)
7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)

1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)

8 - Critical dv/dt: None = 500V/µsec (Standard selection)

ST 73 0 C 18 L 1

2 3

(See Voltage Rating Table)

RRM

L = 1000V/µsec (Special selection)

51

4

12

7

6

8

2222222222222

D-338

Outline Table

58.5 (2 .3) D IA. M A X .

27 (1 .0 6) M AX.

STRIKE DISTANCE 17.43 (0.686) MIN.

To Order

Next Data SheetIndex

Previous Datasheet

0.7 (0.03) MIN.

34 (1.34) DIA. MAX.

TWO PLACES

PIN RECEPTACLE

AMP. 60598-1

ST730C..L Series

0.7 (0.03) MIN.

53 (2.09) DIA. MAX.

2 HOLES DIA. 3.5 (0.14) x

2.5 (0.1) DEEP

CREPAGE DISTANCE 36.33 (1.430) MIN.

6.2 (0.24) MIN.

36.5 (1.44)

Case Style TO-200AC (B-PUK)

All dimensions in millimeters (inches)

4.7 (0.18)

20°± 5°

23

Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics

D-3393333