Datasheet SP9600KN, SP9600KS, SP9600AN, SP9600AS, SP9600BN Datasheet (Sipex Corporation)

®

SP9600

12–Bit, Low Power Voltage Output D/A Con verter

■ Low Power — 0.5mW

■ Voltage Output, 0.5V to 4.5V Range

■ Single +5 Volt Supply

■ 700kHz Multiplying Bandwidth

(2-Quadrant)

■ Standard 3-Wire Serial Interface

■ 8–pin (0.15") SOIC and Plastic DIP

Packages

DESCRIPTION…

The SP9600 is a very low power 12-Bit Digital-to-Analog Converter. It features 0.5 to 4.5 volt
output swing when using a single +5volt supply. The converter uses a standard 3–wire serial
interface compatible with SPI™, QSPI™ and Microwire™. The output settling-time is specified at
20µs. The SP9600 is available in 8–pin 0.15" SOIC and DIP packages, specified over
commercial and industrial temperature ranges.

V

REF

DAC

REGISTER

LATCH

DAC

+
–

V

OUT

AGND

SHIFT

REGISTER

D

SCLKCS

IN

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

1

ABSOLUTE MAXIMUM RATINGS

These are stress ratings only and functional operation of the device
at these or any other above those indicated in the operation
sections of the specifications below is not implied. Exposure to
absolute maximum rating conditions for extended periods of time
may affect reliability.

VDD - DGND ..................................................................-0.3V,+6.0V

V

- .............................................................................. DGND, V

REF

AGND .......................................................................... DGND, V

DIN..................................................................................DGND, V

Power Dissipation

Plastic DIP .......................................................................... 375mW

(derate 7mW/°C above +70°C)

Small Outline ...................................................................... 375mW

(derate 7mW/˚C above +70˚C)

DD

REF

DD

SPECIFICATIONS

(Typical at 25˚C; T

PARAMETER MIN. TYP. MAX. UNITS CONDITIONS
DIGITAL INPUTS

Logic Levels

2 Quad, Input Coding Binary
REFERENCE INPUTS Note 5

V
AGND Voltage Range 0.5 4.5 Volts
Input Resistance 11 13.9 kΩ DIN = 1365; code dependent

ANALOG OUTPUT

Gain

Initial Offset Bipolar ±0.25 ±3.0 LSB DIN = 0
Voltage Range 0.5 4.5 Volts
Output Current ±1.0 mA

STATIC PERFORMANCE

Resolution 12 Bits
Integral Linearity

Differential Linearity

Monotonicity Guaranteed

DYNAMIC PERFORMANCE

Settling Time

Slew Rate 0.3 V/µs
Multiplying Bandwidth 700 KHz

STABILITY

Gain 15 ppm/˚C t
Scale Zero 15 ppm/˚C t

≤ TA ≤ T

; VDD = +5V, DGND = 0V, V

MIN

MAX

V

IH

V

IL

Voltage Range 0.5 4.5 Volts

REF

= +3.5V; AGND = +1.5V; CMOS logic level digital inputs; specifications apply to all grades unless otherwise noted.)

REF

2.4 Volts

0.8 Volts

-B, -K ±0.5 ±2.0 LSB Note 3

-A, -J ±1.0 ±4.0 LSB Note 3
±1.0 ±5.0 LSB V

= 4.5V; AGND = 0.5V

REF

-B, -K ±0.25 ±0.5 LSB Note 3

-A, -J ±0.5 ±1.0 LSB Note 3
±0.5 LSB V

= 4.5V; AGND = 0.5V

REF

-B, -K ±0.25 ±0.75 LSB

-A, -J ±0.25 ±1.0 LSB

Small Signal 2 µs to 0.012%
Full Scale 20 µs

to 0.012%, V

to t

MIN

to t

MIN

MAX
MAX

= 0.5 to 4.5V

OUT

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

2

SPECIFICATIONS (continued)

(Typical at 25˚C; T

PARAMETER MIN. TYP. MAX. UNITS CONDITIONS
POWER REQUIREMENTS Note 5

V

Power Dissipation 0.5 mW

SWITCHING
CHARACTERISTICS

CS Setup Time
(t

SCLK Fall to CS
Fall Hold Time
(t

SCLK Fall to CS Rise
Hold Time
(t

SCLK High Width
(t

SCLK Low Width
(tCL)40 ns

DIN Setup Time
(tDS)50 ns

DIN Hold Time
(tDH)0 ns

≤ TA ≤ T

; VDD = +5V, DGND = 0V, V

MIN

MAX

DD

-J, -K 0.1 0.18 mA

= +3.5V; AGND = +1.5V; CMOS logic level digital inputs; specifications apply to all grades unless otherwise noted.)

REF

+5V, ±3%; Note 4, 5

-A, -B 0.1 0.25 mA

)25 ns

CSS

)20 ns

CSH0

CSH1)

CH)

0ns

40 ns

CS High Pulse Width
(t

)30 ns

CSW

ENVIRONMENTAL AND
MECHANICAL

Operating Temperature

-J, -K 0 +70 °C

-A, -B -40 +85 °C
Storage -60 +150 °C
Package
–_N 8-pin Plastic DIP
–_S 8-pin 0.15" SOIC

Notes:

1. Integral Linearity, for the SP9600, is measured as the arithmetic mean value of the magnitudes of

the greatest positive deviation and the greatest negative deviation from the theoretical value for any
given input condition.

2. Differential Linearity is the deviation of an output step from the theoretical value of 1 LSB for any two

adjacent digital input codes.

3. 1 LSB = (V

4. V

, AGND = 2.5V.

REF

- AGND)/4,096.

REF

5. The following power up sequence is recommended: VDD (+5V), VREF

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

3

PINOUT – 8-PIN PLASTIC DIP & SOIC

THEORY OF OPERATION

V

OUT

V

DD

SCLK

D

1
2

SP9600

3
4

IN

8
7
6
5

V

REF

AGND
DGND
CS

PIN ASSIGNMENTS

Pin 1- V

- Voltage Output.

OUT

Pin 2- VDD - +5V Power Supply Input.
Pin 3- SCLK - Serial Clock Input.
Pin 4- DIN - Serial Data Input.
Pin 5- CS - Chip Select Input.
Pin 6 - DGND - Digital Ground
Pin 7- AGND - Analog Ground.
Pin 8- V

- Reference Input.

REF

FEATURES...

The SP9600 is a low power 12–Bit Digital-to­Analog Converter. The converter features 0.5 to

4.5 volt output swings with a single +5V supply.
The input coding format used is standard binary,
Table 1.

The SP9600 consists of four main functional
blocks – the input shift register, DAC register,
12-Bit D/A converter and a output buffer
amplifier, Figure 1.

The input shift register is used to convert the
serial input data stream to a parallel 12–Bit
digital word. The input data is shifted on posi­tive clock (SCLK) edges when the Chip Select
(CS) signal is in the “low” state. The MSB is
loaded first and LSB last. No shifting of the
input data occurs when the Chip Select (CS)
signal is in the “high” state.

The DAC register is used to store the digital
word which is sent to the R–2R DAC. Its value
is updated on the positive transition of the Chip
Select (CS) signal.

The 12–Bit D/A converter is an “inverted” R-2R
ladder network. The DAC itself is implemented
with precision thin-film resistors and CMOS
transmission gate switches. The resistor net­work is laser-trimmed to achieve better than 12–
Bit accuracy. The D/A converter is used to
convert the 12-bit input word to a precision
voltage.

The operational amplifier is a rail-to-rail input,
rail-to-rail output CMOS amplifier. It is capable
of supplying 1mA of load current in the 1.5 to

3.5 output voltage range. The initial offset volt­age is laser-trimmed to improve accuracy. Set­tling time is 20 µs for a full scale output transi­tion to 0.012% accuracy.

This Digital-to Analog Converter uses a stan­dard 3–wire interface compatible with SPI™,
QSPI™ and Microwire™. The output settling
time is specified at 20 µs to full 12-bit accuracy
when driving a 10kΩ, 10pF load combination.

The SP9600 Digital-to-Analog Converter is
ideally suited for applications such as ATE,
process controllers, robotics and instrumenta­tion. The SP9600 is available in an 8-pin 0.15"
SOIC and 0.3" PDIP packages, specified over

MSB LSB

1111 1111 1111 V
1111 1111 1110 V
0000 0000 0001 AGND + 1 LSB
0000 0000 0000 AGND

Table 1. Binary Coding

INPUT OUTPUT

- 1 LSB

REF

- 2 LSB

REF

(V

-AGND)

1 LSB =

REF

12

2

commercial and industrial temperature ranges.

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

4

+0.5 lsb
DNLE

-0.5 lsb
+0.5 lsb
INLE

0 CODE 4095

DNLE, INLE Plots

USING THE SP9600

External Reference

The R-2R DAC input resistance is code depen­dent and is minimum (11kΩ) at code 1365 and

2731. And, it is nearly infinite at code 0. Because
of the code-dependent nature of the reference

periods plus the CS high pulse width t
is equal to a 1 µs or 1 MHz update rate. However,
the DAC settling time to 12–Bits is 20 µs, which
for full scale output transitions would limit the

update rate to 50 kHz.
inputs, a high quality, low output impedance
amplifier should be used to drive the V
AGND inputs.

REF

and

Logic Interface

The SP9600 is designed to be compatible with

TTL and CMOS logic levels. However, driving

Serial Clock and Update Rate

The SP9600 maximum serial clock rate (SCLK)
is given by 1/(tCH+tCL) which is approximately

12.5 MHz. The digital word update rate is limited
by the chip select period, which is 12 X SCLK

DAC

DAC

DAC

REGISTER

REGISTER

REGISTER

D

IN

SHIFT

REGISTER

121

LATCH

the digital inputs with TTL level signals will

increase the power consumption of the part by

300 µA. In order to achieve the lowest power

consumption use rail-to-rail CMOS levels to

drive the digital inputs.

V

REF

12

DAC

+
–

-0.5 lsb

. This

CSW

V

OUT

AGND

Figure 1. Detailed Block Diagram

V

OUT

WHERE…

=

V

OUT

=

V

DAC

V

DAC

D

IN

4096

x (V

()

- AGND) + AGND

REF

V

REF

D

IN

+
–

V

AGND

Figure 2. Transfer Function

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

DAC

5

CS

t

CSHO

SCLK

t

DS

DIN

Figure 3. Timing Diagram

DB11

t

t

DB9

CL

DB8

t

CSH1

DB0

t

CH

t

CSS

t

DH

DB10

CSW

Figure 4. Microwire Connection

Figure 5. SPI Connection

SCLK

SP9600

SCLK

SP9600

DIN

CS

DIN

CS

N/C

N/C

SK
SO
I/O
SI

MICROWIRE

PORT

SK
MOSI
I/O
MISO

SPI

PORT

CPOL = 0, CPHA = 0

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

6

D1 = 0.005" min.

(0.127 min.)

D

e = 0.100 BSC

(2.540 BSC)

B1

B

ALTERNATE

END PINS

(BOTH ENDS)

PACKAGE: PLASTIC

DUAL–IN–LINE
(NARROW)

E1

E

A1 = 0.015" min.

(0.381min.)

A = 0.210" max.

(5.334 max).

A2

L

C

Ø

eA = 0.300 BSC

(7.620 BSC)

DIMENSIONS (Inches)

Minimum/Maximum

(mm)
A2

B

B1

C

D

E

E1

L

Ø

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

0.355/0.400

(9.017/10.160)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

0.735/0.775

(18.669/19.685)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

0.780/0.800

(19.812/20.320)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

18–PIN

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

0.880/0.920

(22.352/23.368)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

20–PIN

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

0.980/1.060

(24.892/26.924)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

22–PIN8–PIN 14–PIN 16–PIN

0.115/0.195

(2.921/4.953)

0.014/0.022

(0.356/0.559)

0.045/0.070

(1.143/1.778)

0.008/0.014

(0.203/0.356)

1.145/1.155

(29.083/29.337)

0.300/0.325

(7.620/8.255)

0.240/0.280

(6.096/7.112)

0.115/0.150

(2.921/3.810)

0°/ 15°

(0°/15°)

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

7

D

Be

DIMENSIONS (Inches)

Minimum/Maximum

(mm)
A

A1

B

D

E

e

H

h

L

Ø

EH

A

A1

8–PIN

0.053/0.069

(1.346/1.748)

0.004/0.010

(0.102/0.249

0.014/0.019
(0.35/0.49)

0.189/0.197
(4.80/5.00)

0.150/0.157

(3.802/3.988)

0.050 BSC

(1.270 BSC)

0.228/0.244

(5.801/6.198)

0.010/0.020

(0.254/0.498)

0.016/0.050

(0.406/1.270)

0°/8°

(0°/8°)

PACKAGE: PLASTIC

h x 45°

14–PIN

0.053/0.069

(1.346/1.748)

0.004/0.010

(0.102/0.249)

0.013/0.020

(0.330/0.508)

0.337/0.344

(8.552/8.748)

0.150/0.157

(3.802/3.988)

0.050 BSC

(1.270 BSC)

0.228/0.244

(5.801/6.198)

0.010/0.020

(0.254/0.498)

0.016/0.050

(0.406/1.270)

0°/8°

(0°/8°)

16–PIN

0.053/0.069

(1.346/1.748)

0.004/0.010

(0.102/0.249)

0.013/0.020

(0.330/0.508)

0.386/0.394

(9.802/10.000)

0.150/0.157

(3.802/3.988)

0.050 BSC

(1.270 BSC)

0.228/0.244

(5.801/6.198)

0.010/0.020

(0.254/0.498)

0.016/0.050

(0.406/1.270)

0°/8°

(0°/8°)

SMALL OUTLINE (SOIC)
(NARROW)

Ø

L

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

8

ORDERING INFORMATION

Model .................................................................................. Temperature Range .......................................................................................Package

Monolithic 12-Bit DAC Voltage Output:

SP9600JN ................................................................................ 0˚C to +70˚C .......................................................................... 8-pin, 0.3" Plastic DIP

SP9600KN ...............................................................................0˚C to +70˚C .......................................................................... 8-pin, 0.3" Plastic DIP

SP9600JS ................................................................................ 0˚C to +70˚C ................................................................................. 8–pin, 0.15" SOIC

SP9600KS ............................................................................... 0˚C to +70˚C ................................................................................. 8–pin, 0.15" SOIC

SP9600AN ...............................................................................–40˚C to +85˚C ...................................................................... 8-pin, 0.3" Plastic DIP

SP9600BN ...............................................................................–40˚C to +85˚C ...................................................................... 8-pin, 0.3" Plastic DIP

SP9600AS ............................................................................... –40˚C to +85˚C ............................................................................. 8–pin, 0.15" SOIC

SP9600BS ............................................................................... –40˚C to +85˚C ............................................................................. 8–pin, 0.15" SOIC

Corporation

SIGNAL PROCESSING EXCELLENCE

Sipex Corporation
Headquarters and

Sales Office

22 Linnell Circle
Billerica, MA 01821
TEL: [phone]
FAX: [phone]
e-mail: [e-mail]

Sales Office

233 South Hillview Drive
Milpitas, CA 95035
TEL: [phone]
FAX: [phone]

Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the
application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others.

SP9600DS/04 SP9600 12-Bit, Low Power Voltage Output D/A Converter © Copyright 2000 Sipex Corporation

9