Page 1
SN74LS76A
Dual JK Flip-Flop
with Set and Clear
The SN74LS76A offers individual J, K, Clock Pulse, Direct Set and
Direct Clear inputs. These dual flip-flops are designed so that when
the clock goes HIGH, the inputs are enabled and data will be accepted.
The Logic Level of the J and K inputs will perform according to the
Truth Table as long as minimum set-up times are observed. Input data
is transferred to the outputs on the HIGH-to-LOW clock transitions.
MODE SELECT – TRUTH TABLE
OPERATING
MODE
Set
Reset (Clear)
*Undetermined
Toggle
Load “0” (Reset)
Load “1” (Set)
Hold
* Both outputs will be HIGH while both SD and CD are LOW, but the output
states are unpredictable if S
H, h = HIGH Voltage Level
L, I = LOW Voltage Level
X = Immaterial
l, h (q) = Lower case letters indicate the state of the referenced input
i, h (q) = (or output) one setup time prior to the HIGH–to–LOW clock transition
S
D
L
H
L
H
H
H
H
INPUTS OUTPUTS
C
D
H
L
L
H
H
H
H
and CD go HIGH simultaneously.
D
J K Q Q
X
X
X
h
l
h
l
X
X
X
h
h
l
l
H
L
H
q
L
H
q
L
H
H
q
H
L
q
http://onsemi.com
LOW
POWER
SCHOTTKY
16
1
PLASTIC
N SUFFIX
CASE 648
16
1
SOIC
D SUFFIX
CASE 751B
GUARANTEED OPERATING RANGES
Symbol Parameter Min Typ Max Unit
V
CC
T
I
OH
I
OL
Semiconductor Components Industries, LLC, 1999
December, 1999 – Rev. 6
Supply Voltage 4.75 5.0 5.25 V
Operating Ambient
A
T emperature Range
Output Current – High –0.4 mA
Output Current – Low 8.0 mA
0 25 70 °C
1 Publication Order Number:
ORDERING INFORMATION
Device Package Shipping
SN74LS76AN 16 Pin DIP 2000 Units/Box
SN74LS76AD 16 Pin
2500/Tape & Reel
SN74LS76A/D
Page 2
SN74LS76A
VOLOutput LOW Voltage
V
V
V
IIHInput HIGH Current
PLH
Clock, Clear, Set to Output
C
L
F
V
V
CLEAR (C
LOGIC DIAGRAM
Q
)
D
J
Q
SET (S
K
16
1
4
)
D
LOGIC SYMBOL
S
D
KQ
CP
JQ
C
3 8
15
14
D
VCC = PIN 5
GND = PIN 13
CLOCK (CP
)
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits
Symbol Parameter
V
IH
V
IL
V
IK
V
OH
Input HIGH Voltage 2.0 V
Input LOW Voltage
Input Clamp Diode Voltage –0.65 –1.5 V VCC = MIN, IIN = –18 mA
Output HIGH Voltage
p
J, K
Clear
Clock
p
J, K
Clear
Clock
I
IL
I
OS
I
CC
Input LOW Current
Short Circuit Current (Note 1) –20 –100 mA VCC = MAX
Power Supply Current 6.0 mA VCC = MAX
J, K
Clear, Clock
Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.
AC CHARACTERISTICS (T
= 25°C, VCC = 5.0 V)
A
Symbol Parameter
f
MAX
t
PLH
t
PHL
Maximum Clock Frequency 30 45 MHz
p
Min Typ Max
Unit Test Conditions
Guaranteed Input HIGH Voltage for
All Inputs
0.8
Guaranteed Input LOW Voltage for
V
All Inputs
2.7 3.5 V VCC = MIN, IOH = MAX, VIN = V
or VIL per Truth Table
0.25 0.4 V IOL = 4.0 mA
0.35 0.5 V IOL = 8.0 mA
20
60
µA VCC = MAX, VIN = 2.7 V
80
0.1
0.3
mA VCC = MAX, VIN = 7.0 V
0.4
–0.4
–0.8
mA VCC = MAX, VIN = 0.4 V
Limits
Min Typ Max
Unit Test Conditions
15 20 ns
15 20 ns
12
KQ
6
CP
9
JQ
VCC = VCC MIN,
IN
per Truth Table
VCC = 5.0 V
= 15 pF
15
C
=
72
S
D
11
C
D
10
IH
or
IL
IH
AC SETUP REQUIREMENTS (T
Symbol Parameter
t
W
t
W
t
s
t
h
= 25°C)
A
Limits
Min Typ Max
Unit Test Conditions
Clock Pulse Width High 20 ns
Clear Set Pulse Width 25 ns
Setup Time 20 ns
Hold Time 0 ns
http://onsemi.com
2
CC
= 5.0
Page 3
P ACKAGE DIMENSIONS
–A–
916
B
18
F
H
G
D
16 PL
0.25 (0.010) T
C
S
–T–
K
M
A
SN74LS76A
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
L
SEATING
PLANE
J
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM MIN MAX MIN MAX
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC 2.54 BSC
M
H 0.050 BSC 1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0 10 0 10
S 0.020 0.040 0.51 1.01
MILLIMETERSINCHES
____
–T–
–A–
16 9
–B–
18
G
K
C
SEATING
PLANE
D
16 PL
0.25 (0.010) A
M
S
B
T
S
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
8 PLP
M
0.25 (0.010) B
M
S
X 45
R
_
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
DIM MIN MAX MIN MAX
F
J
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
____
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
INCHESMILLIMETERS
http://onsemi.com
3
Page 4
SN74LS76A
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability ,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly , any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer .
PUBLICATION ORDERING INFORMATION
North America Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 2:30pm to 5:00pm Munich Time)
Email: ONlit–german@hibbertco.com
French Phone: (+1) 303–308–7141 (M–F 2:30pm to 5:00pm Toulouse Time)
Email: ONlit–french@hibbertco.com
English Phone: (+1) 303–308–7142 (M–F 1:30pm to 5:00pm UK Time)
Email: ONlit@hibbertco.com
http://onsemi.com
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
T oll Free from Hong Kong 800–4422–3781
Email: ONlit–asia@hibbertco.com
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, T okyo, Japan 141–8549
Phone: 81–3–5487–8345
Email: r14153@onsemi.com
Fax Response Line: 303–675–2167
800–344–3810 Toll Free USA/Canada
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
SN74LS76A/D
4
Loading...