Datasheet SN74LS245H, SN74LS245M, SN74LS245MEL, SN74LS245ML1, SN74LS245ML2 Datasheet (MOTOROLA)

 Semiconductor Components Industries, LLC, 1999

December, 1999 – Rev. 6

1 Publication Order Number:

SN74LS245/D

SN74LS245

Octal Bus Transceiver

The SN74LS245 is an Octal Bus Transmitter/Receiver designed for
8-line asynchronous 2-way data communication between data buses.
Direction Input (DR) controls transmission of Data from bus A to bus
B or bus B to bus A depending upon its logic level. The Enable input
(E

) can be used to isolate the buses.

• Hysteresis Inputs to Improve Noise Immunity

• 2-Way Asynchronous Data Bus Communication

• Input Diodes Limit High-Speed Termination Effects

• ESD > 3500 Volts

LOGIC AND CONNECTION DIAGRAMS DIP (TOP VIEW)

18 17 16 15 14 13

123456

7

20 19

8

V

CC

DIR

E

B1 B2 B3 B5B4 B6

A1 A2 A3 A4 A5 A6 A7

910

A8 GND

12 11

B7 B8

TRUTH TABLE

INPUTS
E DIR

OUTPUT

L L Bus B Data to Bus A
L H Bus A Data to Bus B
H X Isolation

H = HIGH Voltage Level
L = LOW Voltage Level
X = Immaterial

GUARANTEED OPERATING RANGES

Symbol Parameter Min Typ Max Unit

V

CC

Supply Voltage 4.75 5.0 5.25 V

T

A

Operating Ambient

T emperature Range

0 25 70 °C

I

OH

Output Current – High

–3.0 mA

–15 mA

I

OL

Output Current – Low 24 mA

LOW

POWER

SCHOTTKY

Device Package Shipping

ORDERING INFORMATION

SN74LS245N 16 Pin DIP 1440 Units/Box
SN74LS245DW 16 Pin

SOIC
DW SUFFIX
CASE 751D

http://onsemi.com

2500/Tape & Reel

PLASTIC
N SUFFIX
CASE 738

20

1

20

1

SN74LS245

http://onsemi.com

2

DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)

Limits

Symbol Parameter

Min Typ Max

Unit Test Conditions

V

IH

Input HIGH Voltage 2.0 V

Guaranteed Input HIGH Voltage for
All Inputs

V

IL

Input LOW Voltage

0.8
V

Guaranteed Input LOW Voltage for
All Inputs

VT+–V

T–

Hysteresis 0.2 0.4 V VCC = MIN

V

IK

Input Clamp Diode Voltage –0.65 –1.5 V VCC = MIN, IIN = –18 mA

p

2.4 3.4 V VCC = MIN, IOH = –3.0 mA

VOHOutput HIGH Voltage

2.0 V VCC = MIN, IOH = MAX

p

0.25 0.4 V IOL = 12 mA

VCC = VCC MIN,

VOLOutput LOW Voltage

0.35 0.5 V IOL = 24 mA

V

IN

=

V

IL

or

V

IH

per Truth Table

I

OZH

Output Off Current HIGH 20 µA VCC = MAX, V

OUT

= 2.7 V

I

OZL

Output Off Current LOW –200 µA VCC = MAX, V

OUT

= 0.4 V

A or B, DR or
E

20 µA VCC = MAX, VIN = 2.7 V

I

IH

Input HIGH Current

DR or E 0.1 mA VCC = MAX, VIN = 7.0 V
A or B 0.1 mA VCC = MAX, VIN = 5.5 V

I

IL

Input LOW Current –0.2 mA VCC = MAX, VIN = 0.4 V

I

OS

Output Short Circuit Current (Note 1) –40 –225 mA VCC = MAX
Power Supply Current

Total, Output HIGH

70

I

CC

Total, Output LOW 90

mA VCC = MAX

Total at HIGH Z 95

Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.

AC CHARACTERISTICS (T

A

= 25°C, VCC = 5.0 V, T

RISE/TFALL

≤ 6.0 ns)

Limits

Symbol Parameter

Min Typ Max

Unit Test Conditions

t

PLH

t

PHL

Propagation Delay , Data to Output

8.0

8.0

12
12

ns

=

p

t

PZH

Output Enable Time to HIGH Level 25 40 ns

C

L

= 45 F,

R

L

= 667 Ω

t

PZL

Output Enable Time to LOW Level 27 40 ns

t

PLZ

Output Disable Time from LOW Level 15 25 ns

CL = 5.0 pF,

t

PHZ

Output Disable Time from HIGH Level 15 25 ns

L

RL = 667 Ω

SN74LS245

http://onsemi.com

3

P ACKAGE DIMENSIONS

N SUFFIX

PLASTIC PACKAGE

CASE 738–03

ISSUE E

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.

M

L

J

20 PL

M

B

M

0.25 (0.010) T

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A 25.66 27.171.010 1.070
B 6.10 6.600.240 0.260
C 3.81 4.570.150 0.180
D 0.39 0.550.015 0.022

G 2.54 BSC0.100 BSC

J 0.21 0.380.008 0.015

K 2.80 3.550.110 0.140

L 7.62 BSC0.300 BSC
M 0 15 0 15
N 0.51 1.010.020 0.040

____

E

1.27 1.770.050 0.070

1

11

10

20

–A–

SEATING
PLANE

K

N

FG

D

20 PL

–T–

M

A

M

0.25 (0.010) T

E

B

C

F

1.27 BSC0.050 BSC

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751D–05

ISSUE F

20

1

11

10

B20X

H10X

C

L

18X

A1

A

SEATING
PLANE

q

h X 45

_

E

D

M

0.25

M

B

M

0.25

SAS

B

T

e

T

B

A

DIM MIN MAX

MILLIMETERS

A 2.35 2.65

A1 0.10 0.25

B 0.35 0.49
C 0.23 0.32
D 12.65 12.95
E 7.40 7.60
e 1.27 BSC
H 10.05 10.55
h 0.25 0.75
L 0.50 0.90

q

0 7

NOTES:

1. DIMENSIONS ARE IN MILLIMETERS.

2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.

3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION SHALL
BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT
MAXIMUM MATERIAL CONDITION.

__

SN74LS245

http://onsemi.com

4

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes

without further notice to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability ,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly , any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer .

PUBLICATION ORDERING INFORMATION

ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: [phone] (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)

T oll Free from Hong Kong 800–4422–3781

Email: ONlit–[e-mail]
JAPAN: ON Semiconductor, Japan Customer Focus Center

4–32–1 Nishi–Gotanda, Shinagawa–ku, T okyo, Japan 141–8549

Phone: [phone]
Email: [e-mail]

Fax Response Line: 303–675–2167

800–344–3810 Toll Free USA/Canada
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local

Sales Representative.

SN74LS245/D

North America Literature Fulfillment:

Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA

Phone: [phone] or 800–344–3860 T oll Free USA/Canada
Fax: [phone] or 800–344–3867 Toll Free USA/Canada
Email: [e-mail]

N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support

German Phone: [phone] (M–F 2:30pm to 5:00pm Munich Time)

Email: ONlit–[e-mail]

French Phone: [phone] (M–F 2:30pm to 5:00pm Toulouse Time)

Email: ONlit–[e-mail]

English Phone: [phone] (M–F 1:30pm to 5:00pm UK Time)

Email: [e-mail]