Datasheet SN74LS145D, SN74LS145DR2, SN74LS145M, SN74LS145MEL, SN74LS145ML1 Datasheet (MOTOROLA)
...Page 1
Semiconductor Components Industries, LLC, 1999
December, 1999 – Rev. 6
1 Publication Order Number:
SN74LS145/D
SN74LS145
1-of-10 Decoder/Driver
Open-Collector
The SN74LS145, 1-of-10 Decoder/Driver, is designed to accept
BCD inputs and provide appropriate outputs to drive 10-digit
incandescent displays. All outputs remain off for all invalid binary
input conditions. It is designed for use as indicator/relay drivers or as
an open-collector logic circuit driver. Each of the high breakdown
output transistors will sink up to 80 mA of current. Typical power
dissipation is 35 mW. This device is fully compatible with all TTL
families.
• Low Power Version of 74145
• Input Clamp Diodes Limit High Speed Termination Effects
GUARANTEED OPERATING RANGES
Symbol Parameter Min Typ Max Unit
V
CC
Supply Voltage 4.75 5.0 5.25 V
T
A
Operating Ambient
T emperature Range
0 25 70 °C
V
OH
Output Voltage – High 15 V
I
OL
Output Current – Low 24 mA
LOW
POWER
SCHOTTKY
Device Package Shipping
ORDERING INFORMATION
SN74LS145N 16 Pin DIP 2000 Units/Box
SN74LS145D 16 Pin
SOIC
D SUFFIX
CASE 751B
http://onsemi.com
2500/Tape & Reel
PLASTIC
N SUFFIX
CASE 648
16
1
16
1
Page 2
SN74LS145
http://onsemi.com
2
CONNECTION DIAGRAM DIP (TOP VIEW)
BCD Inputs
Outputs
P0, P1, P2, P
3
Q0 – Q
9
0.5 U.L.
Open Collector
0.25 U.L.
15 U.L.
NOTES:
a) 1 TTL Unit Load (U.L.) = 40 mA HIGH/1.6 mA LOW.
HIGH LOW
(Note a)LOADING
PIN NAMES
V
CC
= PIN 16
GND = PIN 8
LOGIC SYMBOL
15 14 13 12
P
0P1P2P3
Q0Q1Q2Q3Q4Q6Q7Q8Q
9
Q
5
123456791011
14 13 12 11 10 9
123456
7
16 15
8
V
CC
Q
0
P0P1P2P
3
Q
8
Q
9
Q
7
Q1Q2Q3Q4Q5Q6GND
Page 3
SN74LS145
http://onsemi.com
3
LOGIC DIAGRAM
INPUTS
INPUT
INVERTERS
DECODE/DRIVER
GATES
OUTPUTS
P
0
P
1
P
2
P
3
01230 1 2 3
Q0Q1Q2Q3Q4Q5Q6Q7Q8Q
9
TRUTH TABLE
INPUTS OUTPUTS
P3P2P1P0Q0Q1Q2Q3Q4Q5Q6Q7Q8Q
9
L L L L L H H H H H H H H H
L LLHHLHHHHHHHH
L LHLHHLHHHHHHH
L LHHHHHLHHHHHH
L HLLHHHHLHHHHH
L HLHHHHHHLHHHH
L HHLHHHHHHLHHH
L HHHHHHHHHHLHH
H LLLHHHHHHHHLH
H LLHHHHHHHHHHL
H LHLHHHHHHHHHH
H LHHHHHHHHHHHH
H HLLHHHHHHHHHH
H HLHHHHHHHHHHH
H HHLHHHHHHHHHH
H HHHHHHHHHHHHH
H = HIGH Voltage Level
L = LOW Voltage Level
Page 4
SN74LS145
http://onsemi.com
4
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits
Symbol Parameter
Min Typ Max
Unit Test Conditions
V
IH
Input HIGH Voltage 2.0 V
Guaranteed Input HIGH Voltage for
All Inputs
V
IL
Input LOW Voltage
0.8
V
Guaranteed Input LOW Voltage for
All Inputs
V
IK
Input Clamp Diode Voltage –0.65 –1.5 V VCC = MIN, IIN = –18 mA
I
OH
Output HIGH Current 250 µA VCC = MIN, VOH = MAX
0.25 0.4 V IOL = 12 mA
=
V
OL
Output LOW Voltage
0.35 0.5 V IOL = 24 mA
V
CC
=
V
CC
MIN
,
V
IN
= VIL or V
IH
2.3 3.0 V IOL = 80 mA
per Truth Table
p
20 µA VCC = MAX, VIN = 2.7 V
IIHInput HIGH Current
0.1 mA VCC = MAX, VIN = 7.0 V
I
IL
Input LOW Current –0.4 mA VCC = MAX, VIN = 0.4 V
I
CC
Power Supply Current 13 mA VCC = MAX, VIN = GND
AC CHARACTERISTICS (T
A
= 25°C)
Limits
Symbol Parameter
Min Typ Max
Unit T est Conditions
t
PHL
t
PLH
Propagation Delay
P
n
Input to Qn Output
50
50
ns
VCC = 5.0 V
C
L
= 45 pF
AC WAVEFORMS
Figure 1. Figure 2.
V
IN
V
OUT
1.3 V
t
PHL
1.3 V
1.3 V
t
PLH
1.3 V
V
IN
V
OUT
1.3 V
t
PHL
1.3 V
1.3 V
t
PLH
1.3 V
Page 5
SN74LS145
http://onsemi.com
5
P ACKAGE DIMENSIONS
N SUFFIX
PLASTIC PACKAGE
CASE 648–08
ISSUE R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A–
B
F
C
S
H
G
D
J
L
M
16 PL
SEATING
18
916
K
PLANE
–T–
M
A
M
0.25 (0.010) T
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0 10 0 10
S 0.020 0.040 0.51 1.01
____
Page 6
SN74LS145
http://onsemi.com
6
P ACKAGE DIMENSIONS
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
18
16 9
SEATING
PLANE
F
J
M
R
X 45
_
G
8 PLP
–B–
–A–
M
0.25 (0.010) B
S
–T–
D
K
C
16 PL
S
B
M
0.25 (0.010) A
S
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
____
Page 7
SN74LS145
http://onsemi.com
7
Notes
Page 8
SN74LS145
http://onsemi.com
8
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability ,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly , any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer .
PUBLICATION ORDERING INFORMATION
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
T oll Free from Hong Kong 800–4422–3781
Email: ONlit–asia@hibbertco.com
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, T okyo, Japan 141–8549
Phone: 81–3–5487–8345
Email: r14153@onsemi.com
Fax Response Line: 303–675–2167
800–344–3810 Toll Free USA/Canada
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
SN74LS145/D
North America Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 T oll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 2:30pm to 5:00pm Munich Time)
Email: ONlit–german@hibbertco.com
French Phone: (+1) 303–308–7141 (M–F 2:30pm to 5:00pm Toulouse Time)
Email: ONlit–french@hibbertco.com
English Phone: (+1) 303–308–7142 (M–F 1:30pm to 5:00pm UK Time)
Email: ONlit@hibbertco.com
Loading...