Datasheet SL339D, SL339N Datasheet (SLS)

Quad Single Supply Comparator

The SL339 consists of four independent precision voltage
comparators with an offset voltage specification as low as 2.0 mV max
for four comparators which were designed specifically to operate from a
single power supply over a wide range of voltages.

Application areas include limit comparators, simple analog to digital
converters; pulse, squarewave and time delay generators; wide range
VCO; MOS clock timers; multivibrators and high voltage digital logic
gates.

• Single or Split Supply Operation

• Low Input Bias Current

• Low Input Offset Current

• Input Common Mode Voltage Range to Gnd

• Low Output Saturation Voltage

• TTL and CMOS Compatible

SL339

ORDERING INFORMATION

SL339N Plastic

SL339D SOIC

TA = 0° to 70° C for all packages.

LOGIC DIAGRAM

PIN 3 = VCC

PIN 12 = GND

PIN ASSIGNMENT

System Logic

SLS

Semiconductor

SL339

MAXIMUM RATINGS*

Symbol Parameter Value Unit

VCC Power Supply Voltages

Single Supply
Split Supplies

V

Input Differential Voltage Range 36 V

IDR

V

Input Common Mode Voltage Range (1) -0.3 to VCC V

ICR

36

±18

ISC Output Short Circuit to Ground Continuous
IIN Input Current, per pin (2) 50 mA

TJ Junction Temperature

Plastic Packages

150

Tstg Storage Temperature -65 to +150 °C

TL Lead Temperature, 1mm from Case for 10 Seconds 260 °C
PD Power Dissipation @TA=25°C

Plastic Package
Derate above 25°C

*

Maximum Ratings are those values beyond which damage to the device may occur.

1.0

8.0

mW/°C

Functional operation should be restricted to the Recommended Operating Conditions.
Notes:

1. Split Power Supplies.

2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative.

V

°C

W

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit

VCC DC Supply Voltage ±2.5 or

5.0

TA Operating Temperature, All Package Types 0 +70 °C

This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, VIN and V
GND≤(VIN or V

OUT

)≤VCC.

should be constrained to the range

OUT

Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC).
Unused outputs must be left open.

±15 or

30

V

System Logic

SLS

Semiconductor

SL339

DC ELECTRICAL CHARACTERISTICS(T

=0 to +70°C)

A

Guaranteed Limit

Symbol Parameter Test Conditions Min Typ Max Unit

VIO Input Offset Voltage V0=1.4V

- 9.0 mV
VCC=5.0-30V;RS≤100Ω
V

=0V - (VCC-1.5)V

ICR

IIB Input Bias Current V0=1.4V

- 400 nA
VCC=5.0-30V
V

=0V - (VCC-1.5)V

ICR

IIO Input Offset Current V0=1.4V

- ±150 nA
VCC=5.0-30V
V

=0V - (VCC-1.5)V

ICR

V

Input Common Mode

ICR

VCC=5.0-30V 0 VCC-2.0V V

Voltage Range

ICC Supply Current RL=∞,VCC=5.0

RL=∞,VCC=30V

A

Voltage Gain VCC=15V, RL=15KΩ - 200* - V/mV

VOL

t1 Large Signal

Response Time

VIN=TTL Logic Swing,
V

=1.4V, VCC=5.0V,

ref

-

-

2.0*

2.5*

- 300* - ns

RL=5.1KΩ, VRL=5.0V

mA

t2 Response Time VCC=5.0V, RL=5.1KΩ,

VRL=5.0V

I

Output Sink Current VI(-)=1.0V, VI(+)=0V, V0≤1.5V,

sink

VCC=5.0V

V

Saturation Voltage VI(-)=1.0V, VI(+)=0V,

sat

I

≤4.0mA, VCC=5.0V

sink

IOL Output Leakage

Current

V

Differential Input

IDR

Voltage Range

VI(+)=1.0V, VI(-)=0V, V0=5.0V
V0=30V

All VIN≥GND or V -Supply (if
used)

*=@25°C

- 1.3* - µs

6.0* - - mA

- - 700 mV

0.1*
1000

nA

VCC* V

System Logic

SLS

Semiconductor

SL339

TYPICAL PERFORMANCE CHARACTERISTICS

(VCC=1.5V, TA=+25°C, (each comporator))

Figure 1. Normalized Input Offset Voltage

Figure 3. Output Sink Current versus

Output Saturation Voltage

Figure 2. Input Bias Current

System Logic

SLS

Semiconductor