Page 1
www.vishay.com
TO-220AB
G
D
S
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
Power MOSFET
PRODUCT SUMMARY
VDS (V) 600
R
()V
DS(on)
Q
max. (nC) 49
g
Q
(nC) 13
gs
Q
(nC) 20
gd
Configuration Single
= 10 V 0.75
GS
D
FEATURES
• Low gate charge Qg results in simple drive
requirement
• Improved gate, avalanche and dynamic dV/dt
ruggedness
• Fully characterized capacitance and avalanche voltage
and current
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
G
S
N-Channel MOSFET
• Switch mode power supply (SMPS)
• Uninterruptible power supply
• High speed power switching
APPLICABLE OFF LINE SMPS TOPOLOGIES
• Active clamped forward
•Main switch
ORDERING INFORMATION
Package TO-220AB
Lead (Pb)-free
SnPb
IRFB9N60APbF
SiHFB9N60A-E3
IRFB9N60A
SiHFB9N60A
Available
Available
ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)
PARAMETER SYMBOL LIMIT UNIT
Drain-Source Voltage V
Gate-Source Voltage V
T
= 25 °C
Continuous Drain Current V
Pulsed Drain Current
a
at 10 V
GS
C
= 100 °C 5.8
C
DS
± 30
GS
I
D
IDM 37
Linear Derating Factor 1.3 W/°C
Single Pulse Avalanche Energy
Repetitive Avalanche Current
Repetitive Avalanche Energy
Maximum Power Dissipation T
Peak Diode Recovery dV/dt
Operating Junction and Storage Temperature Range T
Soldering Recommendations (Peak temperature)
b
a
a
= 25 °C P
c
d
C
for 10 s 300
E
AS
I
AR
E
AR
D
dV/dt 5.0 V/ns
, T
J
stg
Mounting Torque 6-32 or M3 screw
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. Starting T
c. I
SD
= 25 °C, L = 6.8 mH, Rg = 25 , IAS = 9.2 A (see fig. 12).
J
9.2 A, dI/dt 50 A/μs, VDD VDS, TJ 150 °C.
d. 1.6 mm from case.
S16-0763-Rev. D, 02-May-16
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
600
9.2
290 mJ
9.2 A
17 mJ
170 W
-55 to +150
10 lbf · in
1.1 N · m
Document Number: 91103
V
AT
°C
Page 2
IRFB9N60A, SiHFB9N60A
S
D
G
www.vishay.com
THERMAL RESISTANCE RATINGS
PARAMETER SYMBOL TYP. MAX. UNIT
Maximum Junction-to-Ambient R
Maximum Junction-to-Case (Drain) R
thJA
thCS
thJC
-62
0.50 -
-0.75
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Static
Drain-Source Breakdown Voltage V
V
Temperature Coefficient VDS/TJ Reference to 25 °C, ID = 1 mA - 660 - mV/°C
DS
Gate-Source Threshold Voltage V
Gate-Source Leakage I
Zero Gate Voltage Drain Current I
Drain-Source On-State Resistance R
Forward Transconductance g
DS
GS(th)
V
GSS
DSS
VGS = 10 V ID = 5.5 A
DS(on)
fs
Dynamic
Input Capacitance C
Output Capacitance C
Reverse Transfer Capacitance C
Output Capacitance C
Effective Output Capacitance C
Total Gate Charge Q
Gate-Drain Charge Q
Turn-On Delay Time t
Rise Time t
Turn-Off Delay Time t
Fall Time t
Gate Input Resistance R
iss
- 180 -
oss
-7.1-
rss
oss
eff. VDS = 0 V to 480 V - 96 -
oss
g
--13
gs
--20
gd
d(on)
r
-30-
d(off)
-22-
f
g
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode Current I
Pulsed Diode Forward Current
a
Body Diode Voltage V
Body Diode Reverse Recovery Time t
Body Diode Reverse Recovery Charge Q
Forward Turn-On Time t
S
I
SM
SD
rr
rr
on
MOSFET symbol
showing the
integral reverse
p - n junction diode
TJ = 25 °C, IF = 9.2 A, dI/dt = 100 A/μs
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. Pulse width 300 μs; duty cycle 2 %.
effective is a fixed capacitance that gives the same charging time as C
c. C
oss
VGS = 0 V, ID = 250 μA 600 - - V
VDS = VGS, ID = 250 μA 2.0 - 4.0 V
= ± 30 V - - ± 100 nA
GS
VDS = 600 V, VGS = 0 V - - 25
= 480 V, VGS = 0 V, TJ = 125 °C - - 250
V
DS
b
VDS = 50 V, ID = 5.5 A 5.5 - - S
VGS = 0 V,
= 25 V,
V
DS
f = 1.0 MHz, see fig. 5
= 1.0 V, f = 1.0 MHz - 1957 -
V
DS
= 0 V
V
GS
= 10 V
V
GS
R
= 9.1 , RD = 35.5 , see fig. 10
g
V
= 480 V, f = 1.0 MHz - 49 -
DS
= 9.2 A, VDS = 400 V
I
D
see fig. 6 and 13
= 300 V, ID = 9.2 A
V
DD
b
b
f = 1 MHz, open drain 0.5 - 3.2
TJ = 25 °C, IS = 9.2 A, VGS = 0 V
b
b
Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
while VDS is rising from 0 % to 80 % VDS.
oss
Vishay Siliconix
°C/WCase-to-Sink, Flat, Greased Surface R
- - 0.75
- 1400 -
--49
-13-
-25-
--9.2
--37
--1.5V
- 530 800 ns
-3.04.4μC
μA
pF
nC Gate-Source Charge Q
ns
A
S16-0763-Rev. D, 02-May-16
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
For technical questions, contact: [email protected]
2
Document Number: 91103
Page 3
www.vishay.com
0.1
1
10
100
0.1 1 10 100
20µs PULSE WIDTH
T = 25 C
J
°
TOP
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.7V
V , Drain-to-Source Voltage (V)
I , Drain-to-Source Current (A)
DS
D
4.7V
-60 -40 -20 0 20 40 60 80 100 120 140 160
0.0
0.5
1.0
1.5
2.0
2.5
3.0
T , Junction Temperature ( C)
R , Drain-to-Source On Resistance
(Normalized)
J
DS(on)
°
V =
I =
GS
D
10V
9.2A
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
Fig. 1 - Typical Output Characteristics
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
100
°
T = 150 C
J
10
°
T = 25 C
J
1
D
I , Drain-to-Source Current (A)
V = 50V
DS
0.1
4.0 5.0 6.0 7.0 8.0 9.0 10.0
V , Gate-to-Source Voltage (V)
GS
Fig. 3 - Typical Transfer Characteristics
20µs PULSE WIDTH
100
10
D
I , Drain-to-Source Current (A)
1
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.7V
1 10 100
V , Drain-to-Source Voltage (V)
DS
Fig. 2 - Typical Output Characteristics
4.7V
20µs PULSE WIDTH
°
T = 150 C
J
Fig. 4 - Normalized On-Resistance vs. Temperature
S16-0763-Rev. D, 02-May-16
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
3
For technical questions, contact: [email protected]
Document Number: 91103
Page 4
www.vishay.com
1
10
100
1000
10000
100000
1 10 100 1000
C, Capacitance (pF)
DS
V , Drain-to-Source Voltage (V)
A
V = 0V, f = 1MHz
C = C + C , C SHORTED
C = C
C = C + C
GS
iss gs gd ds
rss gd
oss ds gd
C
iss
C
oss
C
rss
0 10 20 30 40 50
0
4
8
12
16
20
Q , Total Gate Charge (nC)
V , Gate-to-Source Voltage (V)
G
GS
FOR TEST CIRCUIT
SEE FIGURE
I =
D
13
9.2A
V = 120V
DS
V = 300V
DS
V = 480V
DS
400V
0.1
1
10
100
0.2 0.5 0.7 1.0 1.2
V ,Source-to-Drain Voltage (V)
I , Reverse Drain Current (A)
SD
SD
V = 0 V
GS
T = 25 C
J
°
T = 150 C
J
°
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage
Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage
Fig. 7 - Typical Source-Drain Diode Forward Voltage
1000
OPERATION IN THIS AREA LIMITED
100
10
D
I , Drain Current (A)I , Drain Current (A)
1
°
= 25 C
C
T T= 150 C
Single Pulse
0.1
10 100 1000 10000
°
J
V , Drain-to-Source Voltage (V)
DS
BY R
DS(on)
10us
100us
1ms
10ms
Fig. 8 - Maximum Safe Operating Area
S16-0763-Rev. D, 02-May-16
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4
For technical questions, contact: [email protected]
Document Number: 91103
Page 5
www.vishay.com
25 50 75 100 125 150
0.0
2.0
4.0
6.0
8.0
10.0
T , Case Temperature ( C)
I , Drain Current (A)
°
C
D
V
DS
Pulse width ≤ 1 µs
Duty factor ≤ 0.1 %
R
D
V
GS
R
G
D.U.T.
10V
+
-
V
DD
0.01
0.1
1
0.00001 0.0001 0.001 0.01 0.1 1
Notes:
1. Duty factor D = t / t
2. Peak T =P x Z + T
1 2
J DM thJC C
P
t
t
DM
1
2
t , Rectangular Pulse Duration (s)
Thermal Response (Z )
1
thJC
0.01
0.02
0.05
0.10
0.20
D = 0.50
SINGLE PULSE
(THERMAL RESPONSE)
Fig. 9 - Maximum Drain Current vs. Case Temperature
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
Fig. 10a - Switching Time Test Circuit
V
DS
90 %
10 %
V
GS
t
d(on)tr
Fig. 10b - Switching Time Waveforms
t
d(off)tf
Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case
S16-0763-Rev. D, 02-May-16
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
For technical questions, contact: [email protected]
5
Document Number: 91103
Page 6
www.vishay.com
R
G
I
AS
0.01 W
t
p
D.U.T.
L
V
DS
+
-
V
DD
Driver
A
15 V
20 V
Q
G
Q
GS
Q
GD
V
G
Charge
10 V
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
V
DS
t
p
I
AS
Fig. 12a - Unclamped Inductive Test Circuit
600
500
400
300
200
100
AS
E , Single Pulse Avalanche Energy (mJ)
0
25 50 75 100 125 150
Starting T , Junction Temperature ( C)
Fig. 12c - Maximum Avalanche Energy vs. Drain Current
Fig. 12b - Unclamped Inductive Waveforms
I
TOP
D
4.1A
5.8A
BOTTOM
J
9.2A
°
Current regulator
Same type as D.U.T.
50 kΩ
0.2 µF
12 V
V
GS
0.3 µF
D.U.T.
3 mA
I
G
Current sampling resistors
I
D
+
V
DS
-
Fig. 13a - Basic Gate Charge Waveform Fig. 13b - Gate Charge Test Circuit
S16-0763-Rev. D, 02-May-16
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
6
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
For technical questions, contact: [email protected]
Document Number: 91103
Page 7
www.vishay.com
IRFB9N60A, SiHFB9N60A
Vishay Siliconix
Peak Diode Recovery dV/dt Test Circuit
D.U.T.
+
-
R
g
Driver gate drive
P.W.
+
-
Period
Circuit layout considerations
• Low stray inductance
• Ground plane
• Low leakage inductance
current transformer
• dV/dt controlled by R
• Driver same type as D.U.T.
I
controlled by duty factor “D”
•
SD
• D.U.T. - device under test
-
D =
g
P.W.
Period
+
+
V
DD
-
V
= 10 Va
GS
D.U.T. l
waveform
SD
Reverse
recovery
current
Re-applied
voltage
D.U.T. V
Inductor current
Note
a. V
waveform
DS
= 5 V for logic level devices
GS
Body diode forward
current
dI/dt
Diode recovery
dV/dt
Body diode forward drop
Ripple ≤ 5 %
V
DD
I
SD
Fig. 14 - For N-Channel
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?91103
S16-0763-Rev. D, 02-May-16
.
7
Document Number: 91103
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Page 8
www.vishay.com
M
*
3
2
1
L
L(1)
D
H(1)
Q
Ø P
A
F
J(1)
b(1)
e(1)
e
E
b
C
Package Information
Vishay Siliconix
TO-220-1
DIM.
A 4.24 4.65 0.167 0.183
b 0.69 1.02 0.027 0.040
b(1) 1.14 1.78 0.045 0.070
c 0.36 0.61 0.014 0.024
D 14.33 15.85 0.564 0.624
E 9.96 10.52 0.392 0.414
e 2.41 2.67 0.095 0.105
e(1) 4.88 5.28 0.192 0.208
F 1.14 1.40 0.045 0.055
H(1) 6.10 6.71 0.240 0.264
J(1) 2.41 2.92 0.095 0.115
L 13.36 14.40 0.526 0.567
L(1) 3.33 4.04 0.131 0.159
Ø P 3.53 3.94 0.139 0.155
Q 2.54 3.00 0.100 0.118
ECN: X15-0364-Rev. C, 14-Dec-15
DWG: 6031
Note
• M* = 0.052 inches to 0.064 inches (dimension including
protrusion), heatsink hole for HVM
MILLIMETERS INCHES
MIN. MAX. MIN. MAX.
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Revison: 14-Dec-15
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ASE Xi’an
For technical questions, contact: [email protected]
Package Picture
1
Document Number: 66542
Page 9
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Revision: 13-Jun-16
1
Document Number: 91000
Loading...