Datasheet SCN68681E1A44, SCN68681E1N40, SCN68681C1A44 Datasheet (Philips)

Download

Page 1

INTEGRATED CIRCUITS

SCN68681

Dual asynchronous receiver/transmitter (DUART)

Product specification Supersedes data of 1995 May 01 IC19 Data Handbook

 

1998 Sep 04

Page 2

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

DESCRIPTION

The Philips Semiconductors SCN68681 Dual Universal Asynchronous Receiver/Transmitter (DUART) is a single-chip MOS-LSI communications device that provides two independent full-duplex asynchronous receiver/transmitter channels in a single package. It is compatible with other S68000 family devices, and can also interface easily with other microprocessors. The DUART can be used in polled or interrupt driven systems.

The operating mode and data format of each channel can be programmed independently. Additionally, each receiver and transmitter can select its operating speed as one of eighteen fixed baud rates, a 16X clock derived from a programmable counter/timer, or an external 1X or 16X clock. The baud rate generator and counter/timer can operate directly from a crystal or from external clock inputs. The ability to independently program the operating speed of the receiver and transmitter make the DUART particularly attractive for dual-speed channel applications such as clustered terminal systems.

Each receiver is quadruply buffered to minimize the potential of receiver overrun or to reduce interrupt overhead in interrupt driven systems. In addition, a flow control capability is provided to disable a remote DUART transmitter when the buffer of the receiving device is full.

Also provided on the SCN68681 are a multipurpose 6-bit input port and a multipurpose 8-bit output port. These can be used as general purpose I/O ports or can be assigned specific functions (such as clock inputs or status/interrupt outputs) under program control.

FEA TURES

•S68000 bus compatible

•Dual full-duplex asynchronous receiver/transmitter

•Quadruple buffered receiver data registers

•Programmable data format

– 5 to 8 data bits plus parity – Odd, even, no parity or force parity – 1, 1.5 or 2 stop bits programmable in 1/16-bit increments

•Programmable baud rate for each receiver and transmitter

selectable from:

– 22 fixed rates: 50 to 115.2k baud – Non-standard rates to 115.2kb – Non-standard user-defined rate derived from programmable

counter/timer

– External 1X or 16X clock

•16-bit programmable Counter/Timer

•Parity, framing, and overrun error detection

•False start bit detection

•Line break detection and generation

•Programmable channel mode

– Normal (full-duplex) – Automatic echo – Local loopback – Remote loopback

•Multi-function programmable 16-bit counter/timer

•Multi-function 6-bit input port

– Can serve as clock or control inputs – Change-of-state detection on four inputs – 100kΩ typical pull-up resistors

•Multi-function 8-bit output port

– Individual bit set/reset capability – Outputs can be programmed to be status/interrupt signals

•Versatile interrupt system

– Single interrupt output with eight maskable interrupting

conditions

– Interrupt vector output on interrupt acknowledge – Output port can be configured to provide a total of up to six

separate wire-ORable interrupt outputs

•Maximum data transfer rates:

1X - 1MB/sec, 16X - 125kB/sec

•Automatic wake-up mode for multidrop applications

•Start-end break interrupt/status

•Detects break which originates in the middle of a character

•On-chip crystal oscillator

•Single +5V power supply

•Commercial and industrial temperature ranges available

•DIP and PLCC packages

ORDERING INFORMATION

COMMERCIAL INDUSTRIAL

DESCRIPTION

40-Pin Ceramic Dual In-Line Package (cerdip) Not available SCN68681E1F40 0590B 40-Pin Plastic Dual In-Line Package (DIP) SCN68681C1N40 SCN68681E1N40 SOT129-1 44-Pin Plastic Leaded Chip Carrier (PLCC) SCN68681C1A44 SCN68681E1A44 SOT187-2

1998 Sep 04 853–1083 19970

VCC = +5V +5%,

= 0°C to +70°C

VCC = +5V +10%,

TA = 40°C to +85°C

DWG #

Page 3

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

PIN CONFIGURATIONS

IP3

IP1

IP0

R/WN

DTACKN

RxDB TxDB

OP1

OP3 OP5 OP7

D1 D3 D5

GND

1 2 3

4 5

6 7

8 9

DIP

11 12

13 14 15 16 17 18

40 39 38

37 36

35 34

33 32 31 30 29

28 27 26 25 24 23

22 2120

IP4 IP5

IACKN IP2

CSN RESETN

X2 X1/CLK RxDA TxDA OP0

OP2 OP4 OP6 D0 D2 D4

D6 INTRN

1 NC 16 OP5 31 OP2 2 A1 17 OP7 32 OP0 3 IP3 18 D1 33 TxDA 4A2 19D3 34NC 5 IP1 20 D5 35 RxDA 6 A3 21 D7 36 X1/CLK 7 A4 22 GND 37 X2 8 IP0 23 NC 38 RESETN 9 R/WN 24 INTRN 39 CSN 10 DTACKN 25 D6 40 IP2 11 RxDB 26 D4 41 IACKN 12 NC 27 D2 42 IP5 13 TxDB 28 D0 43 IP4

14 OP1 29 OP6 44 V 15 OP3 30 OP4

PLCC

PIN/FUNCTION

SD00107

Figure 1. Pin Configurations

ABSOLUTE MAXIMUM RATINGS

SYMBOL

T T

STG

Operating ambient temperature range Storage temperature range -65 to +150 °C All voltages with respect to ground

PARAMETER RATING UNIT

See Note 4 °C

-0.5 to +6.0 V

NOTES:

1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condition above those indicated in the operation section of this specification is not implied.

2. For operating at elevated temperatures, the device must be derated based on +150

C maximum junction temperature.

3. This product includes circuitry specifically designed for the protection of its internal devices from damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying any voltages larger than the rated maxima.

4. Parameters are valid over specified temperature range. See Ordering information table for applicable operating temperature range and V supply range.

1998 Sep 04

Page 4

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

BLOCK DIAGRAM

D0–D7

R/WN

DTACKN

CSN

A1–A4

RESETN

INTRN

IACKN

BUS BUFFER

OPERATION CONTROL

ADDRESS

DECODE

R/W CONTROL

INTERRUPT CONTROL

IMR ISR IVR

TIMING

BAUD RATE

GENERATOR

CLOCK

SELECTORS

CONTROL

TIMING

INTERNAL DATABUS

CHANNEL A

TRANSMIT

HOLDING REG

TRANSMIT

SHIFT REGISTER

RECEIVE

HOLDING REG (3)

RECEIVE

SHIFT REGISTER

MR1, 2

CRA SRA

CHANNEL B (AS ABOVE)

INPUT PORT

CHANGE OF

STATE

DETECTORS (4)

IPCR

ACR

TxDA

RxDA

TxDB

RxDB

IP0-IP5

X1/CLK

COUNTER/

TIMER

XTAL OSC

CSRA

CSRB

ACR

CTLR CTLR

OUTPUT PORT

FUNCTION

SELECT LOGIC

OPCR

OPR

OP0-OP7

GND

SD00108

Figure 2. Block Diagram

1998 Sep 04

Page 5

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

PIN DESCRIPTION

SYMBOL TYPE NAME AND FUNCTION

D0-D7 I/O Data Bus: Bidirectional 3-State data bus used to transfer commands, data and status between the DUART and the

CSN I Chip Select: Active-Low input signal. When Low, data transfers between the CPU and the DUART are enabled on

R/WN I Read/Write: A High input indicates a read cycle and a Low input indicates a write cycle, when a cycle is initiated by

A1-A4 I Address Inputs: Select the DUART internal registers and ports for read/write operations. RESETN I Reset: A Low level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), initializes the IVR to hex 0F, puts

DTACKN O Data Transfer Acknowledge: Three-state active Low output asserted in write, read, or interrupt cycles to indicate

INTRN O Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the eight maskable

IACKN I Interrupt Acknowledge: Active-Low input indicating an interrupt acknowledge cycle. In response, the DUART will

X1/CLK I Crystal 1: Crystal connection or an external clock input. A crystal of a clock the appropriate frequency (nominally

X2 I Crystal 2: Crystal connection. See Figure 9. If a crystal is not used it is best to keep this pin not connected although

RxDA I Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low. RxDB I Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High, “space” is Low. TxDA O Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the

TxDB O Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output is held in the

OP0 O Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be deactivated

OP1 O Output 1: General purpose output or Channel B request to send (RTSBN, active-Low). Can be deactivated

OP2 O Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A receiver 1X clock

OP3 O Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B transmitter 1X clock

OP4 O Output 4: General purpose output or Channel A open-drain, active-Low, RxRDYA/FFULLA output. OP5 O Output 5: General purpose output or Channel B open-drain, active-Low, RxRDYB/FFULLB output. OP6 O Output 6: General purpose output or Channel A open-drain, active-Low, TxRDYA output. OP7 O Output 7: General purpose output, or Channel B open-drain, active-Low, TxRDYB output. IP0 I Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN). Pin has an internal V

IP1 I Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN). Pin has an internal V

IP2 I Input 2: General purpose input, or Channel B receiver external clock input (RxCB), or counter/timer external clock

IP3 I Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the external clock is

IP4 I Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external clock is used

IP5 I Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the external clock is

GND I Ground:

CPU. D0 is the least significant bit.

D0-D7 as controlled by the R/WN, RDN and A1-A4 inputs. When High, places the D0-D7 lines in the 3-State condition.

assertion of the CSN input.

OP0-OP7 in the High state, stops the counter/timer, and puts Channel A and B in the inactive state, with the TxDA and TxDB outputs in the mark (High) state. Clears Test modes, sets MR pointer to MR1.

proper transfer of data between the CPU and the DUART.

interrupting conditions are true.

place the interrupt vector on the data bus and will assert DTACKN if it has an interrupt pending.

3.6864 MHz) must be supplied at all times. For crystal connections see Figure 9, Clock Timing.

it is permissible to ground it.

“mark” condition when the transmitter is disabled, idle or when operating in local loopback mode. “Mark” is High, “space” is Low.

‘mark’ condition when the transmitter is disabled, idle, or when operating in local loopback mode. ‘Mark’ is High, ‘space’ is Low.

automatically on receive or transmit.

output.

output, or Channel B receiver 1X clock output.

pull-up device supplying 1 to 4 A of current.

input. When the external clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an internal V

pull-up device supplying 1 to 4 A of current.

used by the transmitter, the transmitted data is clocked on the falling edge of the clock. Pin has an internal V pull-up device supplying 1 to 4 A of current.

by the receiver, the received data is sampled on the rising edge of the clock. Pin has an internal VCC pull-up device supplying 1 to 4 A of current.

used by the transmitter, the transmitted data is clocked on the falling edge of the clock. Pin has an internal V pull-up device supplying 1 to 4 A of current.

I Power Supply: +5V supply input.

1998 Sep 04

Page 6

Philips Semiconductors Product specification

SYMBOL

PARAMETER

TEST CONDITIONS

UNIT

µA

SCN68681Dual asynchronous receiver/transmitter (DUART)

DC ELECTRICAL CHARACTERISTICS T

= -40°C to +85°C, VCC = 5.0V ± 10%1, 2,

LIMITS

Min Typ Max

X1L

X1H

X2L

X2H

IOC I

Input low voltage 0.8 Input high voltage (except X1/CLK) Input high voltage (except X1/CLK)

5 4

2.5

Input high voltage (X1/CLK) 4 Output low voltage IOL = 2.4mA 0.4

Output high voltage (except o.d. outputs) Output high voltage (except o.d. outputs)

Input leakage current VIN = 0 to V Data bus 3-State leakage current VO = 0.4 to V

X1/CLK low input current VIN = 0, X2 grounded X1/CLK high input current VIN = VCC, X2 grounded

5 4

IOH = -400µA 2.4 V IOH = -400µA 2.9

VIN = 0, X2 floated

VIN = VCC, X2 floated

–10 10 –10 10

-4

-3

-1 0

-2

-1.5

0.2

3.5

0 0

mA mA

mA X2 low input current VIN = 0, X1/CLK floated -100 -30 0 µA X2 high input current VIN = VCC, X1/CLK floated 0 +30 100 µA

Open-collector output leakage current Power supply current 0°C to +70°C version

-40°C to +85°C version

VO = 0.4 to V

–10

150 175

µA

NOTES:

1. Parameters are valid over specified temperature range. See Ordering information table for applicable operating temperature range and V supply range.

2. All voltage measurements are referenced to ground (GND). For testing, all inputs except X1/CLK swing between 0.4V and 2.4V with a transition time of 20ns maximum. For X1/CLK this swing is between 0.4V and 4.4V . All time measurements are referenced at inpu t voltages of 0.8V and 2.0V as appropriate.

3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.

< 0°C

4. T

5. T

> 0°C

1998 Sep 04

Page 7

Philips Semiconductors Product specification

SYMBOL

PARAMETER

UNIT

SCN68681Dual asynchronous receiver/transmitter (DUART)

AC CHARACTERISTICS T

= -40°C to +85°C, VCC = 5.0V ± 10%

1, 2, 3, 4

LIMITS

Min Typ

Max

Reset Timing (See Figure 3)

RES

RESETN pulse width 200 ns

Bus Timing (See Figures 4, 5, 6)

RWS

RWH

CSW

CSD

DAL

DCR

DCW

DAH

DAT

CSC

A1-A4 setup time to CSN Low 10 ns A1-A4 hold time from CSN Low 100 ns RWN setup time to CSN High 0 ns RWN holdup time to CSN High 0 ns CSN High pulse width 90 ns

CSN or IACKN High from DTACKN Low 20 ns Data valid from CSN or IACKN Low 175 ns Data bus floating from CSN or IACKN High

100 ns Data setup time to CLK High 100 ns Data hold time from CSN High 20 ns DTACKN Low from read data valid 0 ns DTACKN Low (read cycle) from CLK High 125 ns DTACKN Low (write cycle) from CLK High 125 ns DTACKN High from CSN or IACKN High 100 ns DTACKN High impedance from CSN or IACKN High 125 ns

CSN or IACKN setup time to clock High 90 ns

Port Timing (See Figure 7)

Port input setup time to CSN Low 0 ns Port input hold time from CSN High 0 ns Port output valid from CSN High 400 ns

Interrupt Reset Timing (See Figure 8)

INTRN or OP3-OP7 when used as interrupts negated from:

Read RHR (RxRDY/FFULL interrupt) 300 ns Write THR (TxRDY interrupt) 300 ns

Reset command (delta break interrupt) 300 ns Stop C/T command (counter interrupt) 300 ns Read IPCR (input port change interrupt) 300 ns Write IMR (clear of interrupt mask bit) 300 ns

Clock Timing (See Figure 9)

CLK

CTC

X1/CLK High or Low time 100 ns

X1/CLK frequency 0 3.6864 4.0 MHz CTCLK High or Low time 100 ns CTCLK frequency 0 4.0 MHz RxC High or Low time 220 ns RxC frequency (16X)

(1X)

0 0

2.0

1.0 TxC High or Low time 220 ns TxC frequency (16X)

(1X)

0 0

2.0

1.0

MHz MHz

Transmitter Timing (See Figure 10)

TXD

TCS

TxD output delay from TxC external clock input on IP pin 350 ns Output delay from TxC low at OP pin to TxD data output 150 ns

Receiver Timing (See Figure 1 1)

RXS

RXH

RxD data setup time before RxC high at external clock input on IP pin 240 ns RxD data hold time after RxC high at external clock input on IP pin 200 ns

NOTES:

1. Parameters are valid over specified temp. range. See Ordering information table for applicable operating temp. and V

2. All voltage measurements are referenced to ground (GND). For testing, all inputs except X1/CLK swing between 0.4V and 2.4V with

supply range.

a transition time of 20ns maximum. For X1/CLK this swing is between 0.4V and 4.4V . All time measurements are referenced at input voltages of 0.8V and 2.0V as appropriate.

3. Typical values are at +25°C, typical supply voltages, and typical processing parameters.

4. Test conditions for outputs: C

5. This specification will impose maximum 68000 CPU CLK to 6MHz. Higher CPU CLK can be used if repeating bus reads are not performed.

= 150pF, except interrupt outputs. Test condition for interrupt outputs: CL = 50pF, R

= 2.7kΩ to VCC.

Consecutive write operations to the same command register require at least three edges of the X1 clock between writes.

6. This specification imposes a lower bound on CSN and IACKN Low, guaranteeing that it will be Low for at least 1 CLK period. This requirement is made on CSN only to insure assertion of DTACKN and not to guarantee operation of the part.

7. This spec is made only to insure that DTACKN is asserted with respect to the rising edge of the X1/CLK pin as shown in the timing diagram, not to guarantee operation of the part. If setup time is violated, DTACKN may be asserted as shown, or may be asserted 1 clock cycle later.

8. Operation to 0MHz is assured by design. Minimum test frequency is 2.0MHz.

1998 Sep 04

Page 8

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

BLOCK DIAGRAM

The SCN68681 DUART consists of the following eight major sections: data bus buffer, operation control, interrupt control, timing, communications Channels A and B, input port and output port. Refer to the Block Diagram.

Data Bus Buffer

The data bus buffer provides the interface between the external and internal data buses. It is controlled by the operation control block to allow read and write operations to take place between the controlling CPU and the DUART.

Operation Control

The operation control logic receives operation commands from the CPU and generates appropriate signals to internal sections to control device operation. It contains address decoding and read and write circuits to permit communications with the microprocessor via the data bus buffer. The DTACKN output is asserted during write and read cycles to indicate to the CPU that data has been latched on a write cycle, or that valid data is present on the bus on a read cycle.

Interrupt Control

A single active-Low interrupt output (INTRN) is provided which is activated upon the occurrence of any of eight internal events. Associated with the interrupt system are the Interrupt Mask Register (IMR) and the Interrupt Status Register (ISR), the Auditory Control Register(ACR) and the Interrupt Vector Register (IVR). The IMR may be programmed to select only certain conditions to cause INTRN to be asserted. The ISR can be read by the CPU to determine all currently active interrupting conditions. When IACKN is asserted, and the DUART has an interrupt pending, the DUART responds by placing the contents of the IVR register on the data bus and asserting DTACKN.

Outputs OP3-OP7 can be programmed to provide discrete interrupt outputs for the transmitter, receivers, and counter/timer.

Timing Circuits

The timing block consists of a crystal oscillator, a baud rate generator, a programmable 16-bit counter/timer, and four clock selectors. The crystal oscillator operates directly from a crystal connected across the X1/CLK and X2 inputs. If an external clock of the appropriate frequency is available, it may be connected to X1/CLK. The clock serves as the basic timing reference for the Baud Rate Generator (BRG), the counter/timer, and other internal circuits. A clock signal within the limits specified in the specifications section of this data sheet must always be supplied to the DUART. If an external is used instead of a crystal, X1 should be driven using a configuration similar to the one in Figure 9.

The baud rate generator operates from the oscillator or external clock input and is capable of generating 18 commonly used data communications baud rates ranging from 50 to 38.4k baud. The clock outputs from the BRG are at 16X the actual baud rate. The counter/timer can be used as a timer to produce a 16X clock for any other baud rate by counting down the crystal clock or an external clock. The four clock selectors allow the independent selection, for each receiver and transmitter, of any of these baud rates or external timing signal.

Counter/Timer (C/T)

The counter timer is a 16 bit programmable divider that operates one of three modes: Counter, T imer or Time Out mode. In all three modes it uses the 16-bit value loaded to the CTUR and CTLR registers. (Counter timer upper and lower preset registers).

•In the timer mode it generates a square wave.

•In the counter mode it generates a time delay.

•In the time out mode it monitors the receiver data flow and signals

data flow has paused. In the time out mode the receiver controls the starting/stopping of the C/T.

The counter operates as a down counter and sets its output bit in the ISR (Interrupt Status Register) each time it passes through 0. The output of the counter/timer may be seen on one of the OP pins or as an Rx or Tx clock.

The Timer/Counter is controlled with six (6) “commands”; Start C/T, Stop C/T, write C/T, preset registers, read C/T value, set or reset time out mode.

Please see the detail of the commands under the Counter/Timer register descriptions.

Communications Channels A and B

Each communications channel of the SCN68681 comprises a full-duplex asynchronous receiver/transmitter (DUART). The operating frequency for each receiver and transmitter can be selected independently from the baud rate generator, the counter timer, or from an external input.

The transmitter accepts parallel data from the CPU, converts it to a serial bit stream, inserts the appropriate start, stop, and optional parity bits and outputs a composite serial stream of data on the TxD output pin. The receiver accepts serial data on the RxD pin, converts this serial input to parallel format, checks for start bit, stop bit, parity bit (if any), or break condition and sends an assembled character to the CPU.

The input port pulse detection circuitry uses a 38.4kHz sampling clock derived from one of the baud rate generator taps. This results in a sampling period of slightly more than 25µs (assuming that the clock input is 3.6864MHz). The detection circuitry, in order to guarantee a true change in level has occurred, requires that two successive samples at the new logic level be observed. As a consequence, the minimum duration of the signal change is 25µs if the transition occurs coincident with the first sample pulse. The 50µs time refers to the situation in which the change of state is just missed and the first change of state is not detected until 25µs later.

Input Port

The inputs to this unlatched 6-bit port can be read by the CPU by performing a read operation at address H‘D’. A High input results in a logic 1 while a Low input results in a logic 0. D7 will always read as a logic 1 and D6 will reflect the level of IACKN. The pins of this port can also serve as auxiliary inputs to certain portions of the DUART logic.

Four change-of-state detectors are provided which are associated with inputs IP3, IP2, IP1 and IP0. A High-to-Low or Low-to-High transition of these inputs, lasting longer than 25 - 50µs, will set the corresponding bit in the input port change register. The bits are cleared when the register is read by the CPU. Any change-of-state can also be programmed to generate an interrupt to the CPU.

All the IP pins have a small pull-up device that will source 1 to 4 A of current from V

connections if they are not used.

Output Port

The 8-bit multipurpose output port can be used as a general purpose output port, in which case the outputs are the complements

. These pins do not require pull-up devices or

1998 Sep 04

Page 9

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

of the Output Port Register (OPR). OPR[n] = 1 results in OP[n] = Low and vice versa. Bits of the OPR can be individually set and reset. A bit is set by performing a write operation at address H’E’ with the accompanying data specifying the bits to be reset (1 = set, 0 = no change). Likewise, a bit is reset by a write at address H’F’ with the accompanying data specifying the bits to be reset (1 = reset, 0 = no change).

Outputs can be also individually assigned specific functions by appropriate programming of the Channel A mode registers (MR1A, MR2A), the Channel B mode registers (MR1B, MR2B), and the Output Port Configuration Register (OPCR).

Please note that these pins drive both high and low. HOWEVER when they are programmed to represent interrupt type functions (such as receiver ready, transmitter ready or counter/timer ready) they will be switched to an open drain configuration in which case an external pull-up device would be required.

OPERATION Transmitter

The SCN68681 is conditioned to transmit data when the transmitter is enabled through the command register. The SCN68681 indicates to the CPU that it is ready to accept a character by setting the TxRDY bit in the status register. This condition can be programmed to generate an interrupt request at OP6 or OP7 and INTRN. When a character is loaded into the Transmit Holding Register (THR), the above conditions are negated. Data is transferred from the holding register to transmit shift register when it is idle or has completed transmission of the previous character. The TxRDY conditions are then asserted again which means one full character time of buffering is provided. Characters cannot be loaded into the THR while the transmitter is disabled.

The transmitter converts the parallel data from the CPU to a serial bit stream on the TxD output pin. It automatically sends a start bit followed by the programmed number of data bits, an optional parity bit, and the programmed number of stop bits. The least significant bit is sent first. Following the transmission of the stop bits, if a new character is not available in the THR, the TxD output remains High and the TxEMT bit in the Status Register (SR) will be set to 1. Transmission resumes and the TxEMT bit is cleared when the CPU loads a new character into the THR. If the transmitter is disabled, it continues operating until the character currently being transmitted is completely sent out. The transmitter can be forced to send a continuous Low condition by issuing a send break command.

The transmitter can be reset through a software command. If it is reset, operation ceases immediately and the transmitter must be enabled through the command register before resuming operation. If CTS operation is enable, the CTSN input must be Low in order for the character to be transmitted. If it goes High in the middle of a transmission, the character in the shift register is transmitted and TxDA then remains in the marking state until CTSN goes Low. The transmitter can also control the deactivation of the RTSN output. If programmed, the RTSN output will be reset one bit time after the character in the transmit shift register and transmit holding register (if any) are completely transmitted, if the transmitter has been disabled.

Receiver

The SCN68681 is conditioned to receive data when enabled through the command register. The receiver looks for a High-to-Low (mark-to-space) transition of the start bit on the RxD input pin. If a transition is detected, the state of the RxD pin is sampled each 16X

clock for 7-1/2 clocks (16X clock mode) or at the next rising edge of the bit time clock (1X clock mode). If RxD is sampled High, the start bit is invalid and the search for a valid start bit begins again. If RxD is still Low, a valid start bit is assumed and the receiver continues to sample the input at one bit time intervals at the theoretical center of the bit, until the proper number of data bits and parity bit (if any) have been assembled, and one stop bit has been detected. The least significant bit is received first. The data is then transferred to the Receive Holding Register (RHR) and the RxRDY bit in the SR is set to a 1. This condition can be programmed to generate an interrupt at OP4 or OP5 and INTRN. If the character length is less than 8 bits, the most significant unused bits in the RHR are set to zero.

After the stop bit is detected, the receiver will immediately look for the next start bit. However, if a non-zero character was received without a stop bit (framing error) and RxD remains Low for one half of the bit period after the stop bit was sampled, then the receiver operates as if a new start bit transition had been detected at that point (one-half bit time after the stop bit was sampled).

The parity error, framing error, and overrun error (if any) are strobed into the SR at the received character boundary, before the RxRDY status bit is set. If a break condition is detected (RxD is Low for the entire character including the stop bit), a character consisting of all zeros will be loaded into the RHR and the received break bit in the SR is set to 1. The RxD input must return to high for two (2) clock edges of the X1 crystal clock for the receiver to recognize the end of the break condition and begin the search for a start bit. This will

usually require a high time of one X1 clock period or 3 X1 edges since the clock of the controller is not synchronous to the X1 clock.

Receiver FIFO

The RHR consists of a First-In-First-Out (FIFO) stack with a capacity of three characters. Data is loaded from the receive shift register into the topmost empty position of the FIFO. The RxRDY bit in the status register is set whenever one or more characters are available to be read, and a FFULL status bit is set if all three stack positions are filled with data. Either of these bits can be selected to cause an interrupt. A read of the RHR outputs the data at the top of the FIFO. After the read cycle, the data FIFO and its associated status bits (see below) are ‘popped’ thus emptying a FIFO position for new data.

Receiver Status Bits

In addition to the data word, three status bits (parity error, framing error, and received break) are also appended to each data character in the FIFO (overrun is not). Status can be provided in two ways, as programmed by the error mode control bit in the mode register. In the ‘character’ mode, status is provided on a character-by-character basis; the status applies only to the character at the top of the FIFO. In the ‘block’ mode, the status provided in the SR for these three bits is the logical-OR of the status for all characters coming to the top of the FIFO since the last ‘reset error’ command was issued. In either mode reading the SR does not affect the FIFO. The FIFO is ‘popped’ only when the RHR is read. Therefore the status register should be read prior to reading the FIFO.

If the FIFO is full when a new character is received, that character is held in the receive shift register until a FIFO position is available. If an additional character is received while this state exits, the contents of the FIFO are not affected; the character previously in the shift register is lost and the overrun error status bit (SR[4]) will be set-upon receipt of the start bit of the new (overrunning) character).

1998 Sep 04

Page 10

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

The receiver can control the deactivation of RTS. If programmed to operate in this mode, the RTSN output will be negated when a valid start bit was received and the FIFO is full. When a FIFO position becomes available, the RTSN output will be re-asserted automatically. This feature can be used to prevent an overrun, in the receiver, by connecting the RTSN output to the CTSN input of the transmitting device.

Receiver Reset and Disable

Receiver disable stops the receiver immediately – data being assembled if the receiver shift register is lost. Data and status in the FIFO is preserved and may be read. A re-enable of the receiver after a disable will cause the receiver to begin assembling characters at the next start bit detected. A receiver reset will discard the present shift register data, reset the receiver ready bit (RxRDY), clear the status of the byte at the top of the FIFO and re-align the FIFO read/write pointers. This has the appearance of “clearing or flushing” the receiver FIFO. In fact, the FIFO is NEVER cleared! The data in the FIFO remains valid until overwritten by another received character. Because of this, erroneous reading or extra reads of the receiver FIFO will miss-align the FIFO pointers and result in the reading of previously read data. A receiver reset will re-align the pointers.

Multidrop Mode

The DUART is equipped with a wake up mode for multidrop applications. This mode is selected by programming bits MR1A[4:3] or MR1B[4:3] to ‘11’ for Channels A and B, respectively. In this mode of operation, a ‘master’ station transmits an address character followed by data characters for the addressed ‘slave’ station. The slave stations, with receivers that are normally disabled, examine the received data stream and ‘wake up’ the CPU (by setting RxRDY) only upon receipt of an address character. The CPU compares the received address to its station address and enables the receiver if it wishes to receive the subsequent data characters. Upon receipt of another address character, the CPU may disable the receiver to initiate the process again.

A transmitted character consists of a start bit, the programmed number of data bits, and Address/Data (A/D) bit, and the programmed number of stop bits. The polarity of the transmitted A/D bit is selected by the CPU by programming bit MR1A[2]/MR1B[2]. MR1A[2]/MR1B[2] = 0 transmits a zero in the A/D bit position, which identifies the corresponding data bits as data while MR1A[2]/MR1B[2] = 1 transmits a one in the A/D bit position, which identifies the corresponding data bits as an address. The

CPU should program the mode register prior to loading the corresponding data bits into the THR.

In this mode, the receiver continuously looks at the received data stream, whether it is enabled or disabled. If disabled, it sets the RxRDY status bit and loads the character into the RHR FIFO if the received A/D bit is a one (address tag), but discards the received character if the received A/D bit is a zero (data tag). If enabled, all received characters are transferred to the CPU via the RHR. In either case, the data bits are loaded into the data FIFO while the A/D bit is loaded into the status FIFO position normally used for parity error (SRA[5] or SRB[5]). Framing error, overrun error, and break detect operate normally whether or not the receive is enabled.

PROGRAMMING

The operation of the DUART is programmed by writing control words into the appropriate registers. Operational feedback is provided via status registers which can be read by the CPU. The addressing of the registers is described in Table 1.

The contents of certain control registers are initialized to zero on RESET. Care should be exercised if the contents of a register are changed during operation, since certain changes may cause operational problems.

For example, changing the number of bits per character while the transmitter is active may cause the transmission of an incorrect character. In general, the contents of the MR, the CSR, and the OPCR should only be changed while the receiver(s) and transmitter(s) are not enabled, and certain changes to the ACR should only be made while the C/T is stopped.

Mode registers 1 and 2 of each channel are accessed via independent auxiliary pointers. The pointer is set to MR1x by RESET or by issuing a ‘reset pointer’ command via the corresponding command register. Any read or write of the mode register while the pointer is at MR1x, switches the pointer to MR2x. The pointer then remains at MR2x, so that subsequent accesses are always to MR2x unless the pointer is reset to MR1x as described above.

Mode, command, clock select, and status registers are duplicated for each channel to provide total independent operation and control. Refer to Table 2 for register bit descriptions. The reserved registers at addresses H‘02’ and H‘OA’ should never be read during normal operation since they are reserved for internal diagnostics.

T able 1. SCN68681 Register Addressing

A4 A3 A2 A1 READ (R/WN = 1) WRITE (R/WN = 0)

0 0 0 0 Mode Register A (MR1A, MR2A) Mode Register A (MR1A, MR2A) 0 0 0 1 Status Register A (SRA) Clock Select Register A (CSRA) 0 0 1 0 BRG Test Command Register A (CRA) 0 0 1 1 Rx Holding Register A (RHRA) Tx Holding Register A (THRA) 0 1 0 0 Input Port Change Register (IPCR) Aux. Control Register (ACR) 0 1 0 1 Interrupt Status Register (ISR) Interrupt Mask Register (IMR) 0 1 1 0 Counter/Timer Upper Value (CTU) C/T Upper Preset Value (CRUR) 0 1 1 1 Counter/Timer Lower Value (CTL) C/T Lower Preset Value (CTLR) 1 0 0 0 Mode Register B (MR1B, MR2B) Mode Register B (MR1B, MR2B) 1 0 0 1 Status Register B (SRB) Clock Select Register B (CSRB) 1 0 1 0 1X/16X Test Command Register B (CRB) 1 0 1 1 Rx Holding Register B (RHRB) Tx Holding Register B (THRB) 1 1 0 0 Interrupt Vector Register (IVR) Interrupt Vector Register (IVR) 1 1 0 1 Input Ports IP0 to IP6 Output Port Conf. Register (OPCR) 1 1 1 0 Start Counter Command Set Output Port Bits Command 1 1 1 1 Stop Counter Command Reset Output Port Bits Command

* See Table 6 for BRG Test frequencies in this data sheet, and

SCC68681 and SCC2698B”

1998 Sep 04

in application notes elsewhere in this publication

“Extended baud rates for SCN2681, SCN68681, SCC2691, SCC2692,

Page 11

Philips Semiconductors Product specification

MR1A

MR2A

CSRB

SRB

SCN68681Dual asynchronous receiver/transmitter (DUART)

Table 2. Register Bit Formats

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

RxRTS

CONTROL

MR1B

NOTE:

*In block error mode, block error conditions must be cleared by using the error reset command (command 4x) or a receiver reset.

MR2B

NOTE:

*Add 0.5 to values shown for 0 - 7 if channel is programmed for 5 bits/char.

0 = No 1 = Yes

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

CHANNEL MODE

00 = Normal 01 = Auto-Echo 10 = Local loop 11 = Remote loop

RxINT

SELECT

0 = RxRDY 1 = FFULL

ERROR MODE*

0 = Char 1 = Block

TxRTS

CONTROL

0 = No 1 = Yes

PARITY MODE

00 = With Parity 01 = Force Parity 10 = No Parity 11 = Multidrop Mode

CTS

ENABLE Tx

0 = 0.563 4 = 0.813 8 = 1.563 C = 1.813 0 = No 1 = Yes

1 = 0.625 5 = 0.875 9 = 1.625 D = 1.875

2 = 0.688 6 = 0.938 A = 1.688 E = 1.938

3 = 0.750 7 = 1.000 B = 1.750 F = 2.000

PARITY

TYPE

0 = Even

1 = Odd

STOP BIT LENGTH*

BITS PER

CHARACTER

00 = 5 01 = 6 10 = 7 11 = 8

CSRA

NOTE:

* See Table 6 for BRG Test frequencies in this data sheet, and “Extended baud rates for SCN2681, SCN68681, SCC2691, SCC2692, SCC68681 and SCC2698B” in application notes elsewhere in this publication

CRA CRB

NOTE:

*Access to the upper four bits of the command register should be separated by three (3) edges of the X1 clock. A disabled transmitter cannot be loaded.

SRA

NOTE:

*These status bits are appended to the corresponding data character in the receive FIFO. A read of the status provides these bits (7:5) from the top of the FIFO together with bits (4:0). These bits are cleared by a “reset error status” command. In character mode they are discarded when the corresponding data character is read from the FIFO. In block error mode, block error conditions must be cleared by using the error reset command (command 4x) or a receiver reset.

OPCR

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

RECEIVER CLOCK SELECT TRANSMITTER CLOCK SELECT

See Text See Text

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

MISCELLANEOUS COMMANDS DISABLE Tx ENABLE Tx DISABLE Rx ENABLE Rx

Not used – should be 0

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

RECEIVED

BREAK*

0 = No 1 = Yes

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

OP7 OP6 OP5 OP4 OP3 OP2

0 = OPR[7] 1 = TxRDYB

FRAMING

ERROR*

0 = No 1 = Yes

0 = OPR[6] 1 = TxRDYA

See Text 0 = No

PARITY

ERROR*

0 = No 1 = Yes

0 = OPR[5] 1 = RxRDY/ FFULLB

OVERRUN

ERROR

0 = No 1 = Yes

0 = OPR[4] 1 = RxRDY/ FFULLA

1 = Yes

0 = No 1 = Yes

TxEMT TxRDY FFULL RxRDY

0 = No 1 = Yes

00 = OPR[3] 01 = C/T OUTPUT 10 = TxCB(1x) 11 = RxCB(1x)

0 = No 1 = Yes

00 = OPR[2] 01 = TxCA(16x) 10 = TxCA(1x) 11 = RxCA(1x)

0 = No 1 = Yes

OPR BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

OPR bit 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1

OP pin 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0

NOTE:

The level at the OP pin is the inverse of the bit in the OPR register.

1998 Sep 04

Page 12

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

Table 2. Register Bit Formats (Continued)

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

ACR

IPCR

ISR

BRG SET

SELECT

0 = set 1 1 = set 2

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

DELTA

IP3

0 = No 1 = Yes

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

INPUT

PORT

CHANGE

0 = No 1 = Yes

DELTA

0 = No 1 = Yes

DELTA

BREAK B

0 = No 1 = Yes

COUNTER/TIMER

MODE AND SOURCE

See Table 4

DELTA

IP2

0 = No 1 = Yes

RxRDY/

FFULLB

0 = No 1 = Yes

IP1

DELTA

IP0

0 = No 1 = Yes

TxRDYB

0 = No 1 = Yes

DELTA IP3 INT

0 = Off 1 = On

IP3 IP2 IP1 IP0

0 = Low 1 = High

COUNTER

READY

0 = No 1 = Yes

DELTA

IP2 INT

0 = Off 1 = On

0 = Low 1 = High

DELTA

BREAK A

0 = No 1 = Yes

DELTA

IP1 INT

0 = Off 1 = On

0 = Low 1 = High

RxRDY/

FFULLA

0 = No 1 = Yes

DELTA IP0 INT

0 = Off 1 = On

0 = Low 1 = High

TxRDYA

0 = No 1 = Yes

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

IN. PORT

IMR

CTUR C/T[15] C/T[14] C/T[13] C/T[12] C/T[11] C/T[10] C/T[9] C/T[8]

CTLR C/T[7] C/T[6] C/T[5] C/T[4] C/T[3] C/T[2] C/T[1] C/T[0]

IVR IVR[7] IVR[6] IVR[5] IVR[4] IVR[3] IVR[2] IVR[1] IVR[0]

CHANGE

INT

0 = Off 1 = On

BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

MR1A – Channel A Mode Register 1

MR1A is accessed when the Channel A MR pointer points to MR1. The pointer is set to MR1 by RESET or by a ‘set pointer’ command applied via CRA. After reading or writing MR1A, the pointer will point to MR2A.

MR1A[7] – Channel A Receiver Request-to-Send Control

This bit controls the deactivation of the RTSAN output (OP0) by the receiver. This output is normally asserted by setting OPR[0] and negated by resetting OPR[0]. MR1A[7] = 1 causes RTSAN to be negated upon receipt of a valid start bit if the Channel A FIFO is full. However, OPR[0] is not reset and RTSAN will be asserted again when an empty FIFO position is available. This feature can be used for flow control to prevent overrun in the receiver by using the RTSAN output signal to control the CTSN input of the transmitting device.

MR1A[6] – Channel A Receiver Interrupt Select

This bit selects either the Channel A receiver ready status (RxRDY) or the Channel A FIFO full status (FFULL) to be used for CPU interrupts. It also causes the selected bit to be output on OP4 if it is programmed as an interrupt output via the OPCR.

DELTA

BREAK B

INT

0 = Off 1 = On

RxRDY/

FFULLB

INT

0 = Off 1 = On

TxRDYB

INT

0 = Off 1 = On

COUNTER

READY

INT

0 = Off 1 = On

MR1A[5] – Channel A Error Mode Select

This bit select the operating mode of the three FIFOed status bits (FE, PE, received break) for Channel A. In the ‘character’ mode, status is provided on a character-by-character basis; the status applies only to the character at the top of the FIFO. In the ‘block” mode, the status provided in the SR for these bits is the accumulation (logical-OR) of the status for all characters coming to the top of the FIFO since the last ‘reset error’ command for Channel A was issued.

MR1A[4:3| – Channel A Parity Mode Select

If ‘with parity’ or ‘force parity’ is selected a parity bit is added to the transmitted character and the receiver performs a parity check on incoming data MR1A[4:3] = 11 selects Channel A to operate in the special multidrop mode described in the Operation section.

MR1A[2] – Channel A Parity Type Select

This bit selects the parity type (odd or even) if the ‘with parity’ mode is programmed by MR1A[4:3], and the polarity of the forced parity bit if the ‘force parity’ mode is programmed. It has no effect if the ‘no parity’ mode is programmed. In the special multidrop mode it selects the polarity of the A/D bit.

DELTA

BREAK A

INT

0 = Off 1 = On

RxRDY/

FFULLA

INT

0 = Off 1 = On

TxRDYA

INT

0 = Off 1 = On

1998 Sep 04

Page 13

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

MR1A[1:0] – Channel A Bits Per Character Select

This field selects the number of data bits per character to be transmitted and received. The character length does not include the start, parity, and stop bits.

MR2A – Channel A Mode Register 2

MR2A is accessed when the Channel A MR pointer points to MR2, which occurs after any access to MR1A. Accesses to MR2A do not change the pointer.

MR2A[7:6] – Channel A Mode Select

Each channel of the DUART can operate in one of four modes. MR2A[7:6] = 00 is the normal mode, with the transmitter and receiver operating independently. MR2A[7:6] = 01 places the channel in the automatic echo mode, which automatically re-transmits the received data. The following conditions are true while in automatic echo mode:

1. Received data is re-clocked and re-transmitted on the TxDA output.

2. The receive clock is used for the transmitter.

3. The receiver must be enabled, but the transmitter need not be enabled.

4. The Channel A TxRDY and TxEMT status bits are inactive.

5. The received parity is checked, but is not regenerated for transmission, i.e. transmitted parity bit is as received.

6. Character framing is checked, but the stop bits are retransmitted as received.

7. A received break is echoed as received until the next valid start bit is detected.

8. CPU to receiver communication continues normally, but the CPU to transmitter link is disabled.

Two diagnostic modes can also be configured. MR2A[7:6] = 10 selects local loopback mode. In this mode:

1. The transmitter output is internally connected to the receiver input.

2. The transmit clock is used for the receiver.

3. The TxDA output is held High.

4. The RxDA input is ignored.

5. The transmitter must be enabled, but the receiver need not be enabled.

6. CPU to transmitter and receiver communications continue normally.

The second diagnostic mode is the remote loopback mode, selected by MR2A[7:6] = 11. In this mode:

1. Received data is re-clocked and re-transmitted on the TxDA output.

2. The receive clock is used for the transmitter.

3. Received data is not sent to the local CPU, and the error status conditions are inactive.

4. The received parity is not checked and is not regenerated for transmission, i.e., transmitted parity is as received.

5. The receiver must be enabled.

6. Character framing is not checked, and the stop bits are retransmitted as received.

7. A received break is echoed as received until the next valid start bit is detected.

The user must exercise care when switching into and out of the various modes. The selected mode will be activated immediately upon mode selection, even if this occurs in the middle of a received or transmitted character. Likewise, if a mode is deselected the device will switch out of the mode immediately. An exception to this is switching out of autoecho or remote loopback modes: if the de-selection occurs just after the receiver has sampled the stop bit (indicated in autoecho by assertion of RxRDY), and the transmitter is enabled, the transmitter will remain in autoecho mode until the entire stop has been re-transmitted.

MR2A[5] – Channel A Transmitter Request-to-Send Control

CAUTION: When the transmitter controls the OP pin (usually used for the RTSN signal) the meaning of the pin is not RTSN at all! Rather, it signals that the transmitter has finished the transmission (i.e., end of block).

This bit allows deactivation of the RTSN output by the transmitter. This output is manually asserted and negated by the appropriate commands issued via the command register. MR2[5] set to 1 caused the RTSN to be reset automatically one bit time after the character(s) in the transmit shift register and in the THR (if any) are completely transmitted (including the programmed number of stop bits) if a previously issued transmitter disable is pending. This feature can be used to automatically terminate the transmission as follows:

1. Program the auto-reset mode: MR2[5]=1

2. Enable transmitter, if not already enabled

3. Assert RTSN via command

4. Send message

5. After the last character of the message is loaded to the THR, disable the transmitter. (If the transmitter is underrun, a special case exists. See note below.)

6. The last character will be transmitted and the RTSN will be reset one bit time after the last stop bit is sent.

NOTE: The transmitter is in an underrun condition when both the TxRDY and the TxEMT bits are set. This condition also exists immediately after the transmitter is enabled from the disabled or reset state. When using the above procedure with the transmitter in the underrun condition, the issuing of the transmitter disable must be delayed from the loading of a single, or last, character until the TxRDY becomes active again after the character is loaded.

MR2A[4] – Channel A Clear-to-Send Control

If this bit is 0, CTSAN has no effect on the transmitter. If this bit is a 1, the transmitter checks the state of CTSAN (IP0) each time it is ready to send a character. If IP0 is asserted (Low), the character is transmitted. If it is negated (High), the TxDA output remains in the marking state and the transmission is delayed until CTSAN goes low. Changes in CTSAN while a character is being transmitted do not affect the transmission of that character.

MR2A[3:0] – Channel A Stop Bit Length Select

This field programs the length of the stop bit appended to the transmitted character. Stop bit lengths of 9/16 to 1 and 1-9/16 to 2 bits, in increments of 1/16 bit, can be programmed for character lengths of 6, 7, and 8 bits. For a character lengths of 5 bits, 1-1/16 to 2 stop bits can be programmed in increments of 1/16 bit. The receiver only checks for a ‘mark’ condition at the center of the first stop bit position (one bit time after the last data bit, or after the parity bit is enabled), in all cases.

1998 Sep 04

Page 14

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

If an external 1X clock is used for the transmitter, MR2A[3] = 0 selects one stop bit and MR2A[3] = 1 selects two stop bits to be transmitted.

MR1B – Channel B Mode Register 1

MR1B is accessed when the Channel B MR pointer points to MR1. The pointer is set to MR1 by RESET or by a ‘set pointer’ command applied via CRB. After reading or writing MR1B, the pointer will point to MR2B.

The bit definitions for this register are identical to MR1A, except that all control actions apply to the Channel B receiver and transmitter and the corresponding inputs and outputs.

MR2B – Channel B Mode Register 2

MR2B is accessed when the Channel B MR pointer points to MR2, which occurs after any access to MR1B. Accesses to MR2B do not change the pointer.

The bit definitions for mode register are identical to the bit definitions for MR2A, except that all control actions apply to the Channel B receiver and transmitter and the corresponding inputs and outputs.

CSRA – Channel A Clock Select Register

CSRA[7:4] – Channel A Receiver Clock Select

This field selects the baud rate clock for the Channel A receiver. The field definition is shown in Table 3.

CSRA[3:0] – Channel A Transmitter Clock Select

This field selects the baud rate clock for the Channel A transmitter. The field definition is as shown in Table 3, except as follows:

CSRA[3:0]

1110 1111

ACR[7] = 0 Baud Rate ACR[7] = 1

IP3-16X IP3-1X

The transmitter and receiver clock is always a 16X clock except for 1111 selection.

Table 3. Baud Rate Clock = 3.6864 MHz

CSRA[7:4] ACR[7] = 0 Baud Rate ACR[7] = 1

0000 50 75 0001 110 110 0010 134.5 134.5 0011 200 150 0100 300 300 0101 600 600 0110 1,200 1,200

0111 1,050 2,000 1000 2,400 2,400 1001 4,800 4,800 1010 7,200 1,800 1011 9,600 9,600 1100 38.4k 19.2k 1101 Timer Timer

1110 IP4-16X IP4-16X

1111 IP4-1X IP4-1X

See Table 6.

CSRB – Channel B Clock Select Register

CSRB[7:4] – Channel B Receiver Clock Select

This field selects the baud rate clock for the Channel B receiver. The field definition is as shown in Table 3, except as follows:

CSRB[7:4]

1110 1111

ACR[7] = 0 Baud Rate ACR[7] = 1

IP2-16X IP2-1X

The receiver clock is always a 16X clock except for CSRB[7:4] =

1111.

CSRB[3:0] – Channel B Transmitter Clock Select

This field selects the baud rate clock for the Channel B transmitter. The field definition is as shown in Table 3, except as follows:

CSRB[3:0]

1110 1111

ACR[7] = 0 Baud Rate ACR[7] = 1

IP5-16X IP5-1X

The transmitter clock is always a 16X clock except for CSRB[3:0] =

1111.

CRA – Channel A Command Register

CRA is a register used to supply commands to Channel A. Multiple commands can be specified in a single write to CRA as long as the commands are non-conflicting, e.g., the ‘enable transmitter’ and ‘reset transmitter’ commands cannot be specified in a single command word.

CRA[7] – Not Used

Should be set to zero for upward compatibility with newer parts.

CRA[6:4] – Miscellaneous Commands

The encoded value of this field may be used to specify a single command as follows:

CRA[6:4] – COMMAND

NOTE: Access to the upper four bits of the command register should be separated by three (3) edges of the X1 clock.

000 No command. 001 Reset MR pointer. Causes the Channel A MR pointer to point to MR1. 010 Reset receiver. Resets the Channel A receiver as if a hardware reset had been ap-

plied. The receiver is disabled and the FIFO is flushed.

011 Reset transmitter. Resets the Channel A transmitter as if a hardware reset had been

applied.

100 Reset error status. Clears the Channel A Received Break, Parity Error, and Overrun

Error bits in the status register (SRA[7:4]). Used in character mode to clear OE status (although RB, PE and FE bits will also be cleared) and in block mode to clear all error status after a block of data has been received.

101 Reset Channel A break change interrupt. Causes the Channel A break detect

change bit in the interrupt status register (ISR[2]) to be cleared to zero.

110 Start break. Forces the TxDA output Low (spacing). If the transmitter is empty the

start of the break condition will be delayed up to two bit times. If the transmitter is active the break begins when transmission of the character is completed. If a character is in the THR, the start of the break will be delayed until that character, or any other loaded subsequently are transmitted. The transmitter must be enabled for this command to be accepted.

111 Stop break. The TxDA line will go High (marking) within two bit times. TxDA will

remain High for one bit time before the next character, if any, is transmitted.

CRA[3] – Disable Channel A Transmitter

This command terminates transmitter operation and reset the TxDRY and TxEMT status bits. However, if a character is being transmitted or if a character is in the THR when the transmitter is disabled, the transmission of the character(s) is completed before assuming the inactive state.

CRA[2] – Enable Channel A Transmitter

Enables operation of the Channel A transmitter. The TxRDY status bit will be asserted.

CRA[1] – Disable Channel A Receiver

This command terminates operation of the receiver immediately – a character being received will be lost. The command has no effect

1998 Sep 04

Page 15

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

on the receiver status bits or any other control registers. If the special multidrop mode is programmed, the receiver operates even if it is disabled. See Operation section.

CRA[0] – Enable Channel A Receiver

Enables operation of the Channel A receiver. If not in the special wake up mode, this also forces the receiver into the search for start-bit state.

CRB – Channel B Command Register

CRB is a register used to supply commands to Channel B. Multiple commands can be specified in a single write to CRB as long as the commands are non-conflicting, e.g., the ‘enable transmitter’ and ‘reset transmitter’ commands cannot be specified in a single command word.

The bit definitions for this register are identical to the bit definitions for CRA, except that all control actions apply to the Channel B receiver and transmitter and the corresponding inputs and outputs.,

SRA – Channel A Status Register

SRA[7] – Channel A Received Break

This bit indicates that an all zero character of the programmed length has been received without a stop bit. Only a single FIFO position is occupied when a break is received further entries to the FIFO are inhibited until the RxDA line to the marking state for at least one-half a bit time two successive edges of the internal or external 1X clock. This will usually require a high time of one X1

clock period or 3 X1 edges since the clock of the controller is not synchronous to the X1 clock.

When this bit is set, the Channel A ‘change in break’ bit in the ISR (ISR[2]) is set. ISR[2] is also set when the end of the break condition, as defined above, is detected.

The break detect circuitry can detect breaks that originate in the middle of a received character. However, if a break begins in the middle of a character, it must persist until at least the end of the next character time in order for it to be detected.

SRA[6] – Channel A Framing Error

This bit, when set, indicates that a stop bit was not detected when the corresponding data character in the FIFO was received. The stop bit check is made in the middle of the first stop bit position.

SRA[5] – Channel A Parity Error

This bit is set when the ‘with parity’ or ‘force parity’ mode is programmed and the corresponding character in the FIFO was received with incorrect parity.

In the special multidrop mode the parity error bit stores the receive A/D bit.

SRA[4] – Channel A Overrun Error

This bit, when set, indicates that one or more characters in the received data stream have been lost. It is set upon receipt of a new character when the FIFO is full and a character is already in the receive shift register waiting for an empty FIFO position. When this occurs, the character in the receive shift register (and its break detect, parity error and framing error status, if any) is lost.

This bit is cleared by a ‘reset error status’ command.

SRA[3] – Channel A Transmitter Empty (TxEMTA)

This bit will be set when the transmitter underruns, i.e., both the TxEMT and TxRDY bits are set. This bit and TxRDY are set when the transmitter is first enabled and at any time it is re-enabled after either (a) reset, or (b) the transmitter has assumed the disabled

state. It is always set after transmission of the last stop bit of a character if no character is in the THR awaiting transmission.

It is reset when the THR is loaded by the CPU, a pending transmitter disable is executed, the transmitter is reset, or the transmitter is disabled while in the underrun condition.

SRA[2] – Channel A Transmitter Ready (TxRDYA)

This bit, when set, indicates that the THR is empty and ready to be loaded with a character. This bit is cleared when the THR is loaded by the CPU and is set when the character is transferred to the transmit shift register. TxRDY is reset when the transmitter is disabled and is set when the transmitter is first enabled, viz., characters loaded into the THR while the transmitter is disabled will not be transmitted.

SRA[1] – Channel A FIFO Full (FFULLA)

This bit is set when a character is transferred from the receive shift register to the receive FIFO and the transfer causes the FIFO to become full, i.e., all three FIFO positions are occupied. It is reset when the CPU reads the RHR. If a character is waiting in the receive shift register because the FIFO is full, FFULL will not be reset when the CPU reads the RHR.

SRA[0] – Channel A Receiver Ready (RxRDY A)

This bit indicates that a character has been received and is waiting in the FIFO to be read by the CPU. It is set when the character is transferred from the receive shift to the FIFO and reset when the CPU reads the RHR, if after this read there are not more characters still in the FIFO.

SRB – Channel B Status Register

The bit definitions for this register are identical to the bit definitions for SRA, except that all status applies to the Channel B receiver and transmitter and the corresponding inputs and outputs.

OPCR – Output Port Configuration Register

OPCR[7] – OP7 Output Select

This bit programs the OP7 output to provide one of the following: 0: The complement of OPR[7].

1: The Channel B transmitter interrupt output which is the comple-

ment of TxRDYB. When in this mode OP7 acts as an opendrain output. Note that this output is not masked by the contents of the IMR.

OPCR[6] – OP6 Output Select

This bit programs the OP6 output to provide one of the following: 0: The complement of OPR[6].

1: The Channel A transmitter interrupt output which is the comple-

ment of TxRDYA. When in this mode OP6 acts as an opendrain output. Note that this output is not masked by the contents of the IMR.

OPCR[5] – OP5 Output Select

This bit programs the OP5 output to provide one of the following: 0: The complement of OPR[5].

1: The Channel B transmitter interrupt output which is the comple-

ment of ISR[5]. When in this mode OP5 acts as an open-drain output. Note that this output is not masked by the contents of the IMR.

OPCR[4] – OP4 Output Select

This field programs the OP4 output to provide one of the following: 0: The complement of OPR[4].

1998 Sep 04

Page 16

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

1: The Channel A receiver interrupt output which is the complement

of ISR[1]. When in this mode OP4 acts as an open-drain output.

Note that this output is not masked by the contents of the IMR.

OPCR[3:2] – OP3 Output Select

This bit programs the OP3 output to provide one of the following: 00: The complement of OPR[3].

01: The counter/timer output, in which case OP3 acts as an open-

drain output. In the timer mode, this output is a square wave at the programmed frequency. In the counter mode, the output remains High until terminal count is reached, at which time it goes Low. The output returns to the High state when the counter is stopped by a stop counter command. Note that this output is not masked by the contents of the IMR.

10: The 1X clock for the Channel B transmitter, which is the clock

that shifts the transmitted data. If data is not being transmitted, a free running 1X clock is output.

11: The 1X clock for the Channel B receiver, which is the clock that

samples the received data. If data is not being received, a free running 1X clock is output.

OPCR[1:0] – OP2 Output Select

This field programs the OP2 output to provide one of the following: 00: The complement of OPR[2].

01: The 16X clock for the Channel A transmitter. This is the clock

selected by CSRA[3:0], and will be a 1X clock if CSRA[3:0] = 1111.

10: The 1X clock for the Channel A transmitter, which is the clock

that shifts the transmitted data. If data is not being transmitted, a free running 1X clock is output.

11: The 1X clock for the Channel A receiver, which is the clock that

samples the received data. If data is not being received, a free running 1X clock is output.

Table 4. Bit Rate Generator Characteristics

Crystal or Clock = 3.6864MHz

NORMAL RATE

(BAUD)

50 0.8 0 75 1.2 0

110 1.759 -0.069

134.5 2.153 0.059 150 2.4 0 200 3.2 0 300 4.8 0 600 9.6 0

1050 16.756 -0.260 1200 19.2 0 1800 28.8 0 2000 32.056 0.175 2400 38.4 0 4800 76.8 0 7200 115.2 0 9600 153.6 0

14.4K 230.4 0

19.2k 307.2 0

28.8K 460.8 0

38.4k 614.4 0

57.6K 921.6 0

115.2K 1843.2K 0

NOTE:

Duty cycle of 16x clock is 50% ± 1%.

ACTUAL 16x

CLOCK (kHz)

ERROR (%)

Asynchronous UART communications can tolerate frequency error of 4.1% to 6.7% in a “clean” communications channel. The percent of error changes as the character length changes. The above percentages range from 5 bits not parity to 8 bits with parity and one stop bit. The error with 8 bits no parity and one stop bit is 4.6%. If a stop bit length of 9/16 is used, the error tolerance will approach 0 due to a variable error of up to 1/16 bit time in receiver clock phase alignment to the start bit.

Table 5. ACR 6:4 Field Definition

ACR [6:4]

000 Counter External (IP2)* 001 Counter TxCA – 1x clock of Channel

010 Counter TxCB – 1x clock of Channel 011 Counter Crystal or external clock 100 Timer (square wave) External (IP2)*

101 Timer (square wave) External (IP2) divided by 16* 110 Timer (square wave) Crystal or external clock

111 Timer (square wave)

NOTE:

* In these modes, the Channel B receiver clock should normally be

generated from the baud rate generator. Timer mode generates squarewave.

MODE CLOCK SOURCE

A transmitter B transmitter (x1/CLK) divided by 16

(X1/CLK) Crystal or external clock (X1/CLK) divided by 16

ACR – Auxiliary Control Register

ACR[7] – Baud Rate Generator Set Select

This bit selects one of two sets of baud rates to be generated by the BRG:

Set 1: 50, 110, 134.5, 200, 300, 600, 1.05k, 1.2k, 2.4k, 4.8k, 7.2k,

9.6k, and 38.4k baud.

Set 2: 75, 110, 134.5, 150, 300, 600, 1.2k, 1.8k, 2.0k, 2.4k, 4.8k,

9.6k, and 19.2k baud.

The selected set of rates is available for use by the Channel A and B receivers and transmitters as described in CSRA and CSRB. Baud rate generator characteristics are given in Table 4.

ACR[6:4] – Counter/Timer Mode And Clock Source Select

This field selects the operating mode of the counter/timer and its clock source as shown in Table 5.

ACR[3:0] – IP3, IP2, IP1, IP0 Change-of-State Interrupt Enable

This field selects which bits of the input port change register (IPCR) cause the input change bit in the interrupt status register (ISR[7]) to be set. If a bit is in the ‘on’ state the setting of the corresponding bit in the IPCR will also result in the setting of ISR[7], which results in the generation of an interrupt output if IMR[7] = 1. If a bit is in the ‘off’ state, the setting of that bit in the IPCR has no effect on ISR[7].

IPCR – Input Port Change Register

IPCR[7] – IP3, IP2, IP1, IP0 Change-of-State

These bits are set when a change-of-state, as defined in the input port section of this data sheet, occurs at the respective input pins. They are cleared when the IPCR is read by the CPU. A read of the IPCR also clears ISR[7], the input change bit in the interrupt status register. The setting of these bits can be programmed to generate an interrupt to the CPU.

1998 Sep 04

Page 17

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

IPCR[3:0] – IP3, IP2, IP1, IP0 Current State

These bits provide the current state of the respective inputs. The information is unlatched and reflects the state of the input pins at the time the IPCR is read.

ISR – Interrupt Status Register

This register provides the status of all potential interrupt sources. The contents of this register are masked by the Interrupt Mask Register (IMR). If a bit in the ISR is a ‘1’ and the corresponding bit in the IMR is also a ‘1’, the INTRN output will be asserted (Low). If the corresponding bit in the IMR is a zero, the state of the bit in the ISR has no effect on the INTRN output. Note that the IMR does not mask the reading of the ISR – the true status will be provided regardless of the contents of the IMR. The contents of this register

are initialized to 00

ISR[7] – Input Port Change Status

This bit is a ‘1’ when a change-of-state has occurred at the IP0, IP1, IP2, or IP3 inputs and that event has been selected to cause an interrupt by the programming of ACR[3:0]. The bit is cleared when the CPU reads the IPCR.

ISR[6] – Channel B Change In Break

This bit, when set, indicates that the Channel B receiver has detected the beginning or the end of a received break. It is reset when the CPU issues a Channel B ‘reset break change interrupt’ command.

ISR[5] – Channel B Receiver Ready or FIFO Full

The function of this bit is programmed by MR1B[6]. If programmed as receiver ready, it indicates that a character has been received in Channel B and is waiting in the FIFO to be read by the CPU. It is set when the character is transferred from the receive shift register to the FIFO and reset when the CPU reads the RHR. If after this read there are more characters still in the FIFO the bit will be set again after the FIFO is ‘popped’. If programmed as FIFO full, it is set when a character is transferred from the receive holding register to the receive FIFO and the transfer caused the Channel B FIFO to become full; i.e., all three FIFO positions are occupied. It is reset when the CPU reads the RHR. If a character is waiting in the receive shift register because the FIFO is full, the bit will be set again when the waiting character is loaded into the FIFO.

ISR[4] – Channel B Transmitter Ready

This bit is a duplicate of TxRDYB (SRB[2]).

ISR[3] – Counter Ready.

In the counter mode, this bit is set when the counter reaches terminal count and is reset when the counter is stopped by a stop counter command.

In the timer mode, this bit is set once each cycle of the generated square wave (every other time that the counter/timer reaches zero count). The bit is reset by a stop counter command. The command, however, does not stop the counter/timer.

ISR[2] – Channel A Change in Break

This bit, when set, indicates that the Channel A receiver has detected the beginning or the end of a received break. It is reset when the CPU issues a Channel A ‘reset break change interrupt’ command.

ISR[1] – Channel A Receiver Ready Or FIFO Full

The function of this bit is programmed by MR1A[6]. If programmed as receiver ready, it indicates that a character has been received in

when the DUART is reset.

Channel A and is waiting in the FIFO to be read by the CPU. It is set when the character is transferred from the receive shift register to the FIFO and reset when the CPU read the RHR. If after this read there are more characters still in the FIFO the bit will be set again after the FIFO is ‘popped’. If programmed as FIFO full, it is set when a character is transferred from the receive holding register to the receive FIFO and the transfer caused the Channel A FIFO to become full; i.e., all three FIFO positions are occupied. It is reset when the CPU reads the RHR. If a character is waiting in the receive shift register because the FIFO is full, the bit will be set again when the ISR[0] and IMR waiting character is loaded into the FIFO.

ISR[0] – Channel A Transmitter Ready

This bit is a duplicate of TxRDYA (SRA[2]).

IMR – Interrupt Mask Register

The programming of this register selects which bits in the ISR causes an interrupt output. If a bit in the ISR is a ‘1’ and the corresponding bit in the IMR is also a ‘1’ the INTRN output will be asserted. If the corresponding bit in the IMR is a zero, the state of the bit in the ISR has no effect on the INTRN output. Note that the IMR does not mask the programmable interrupt outputs OP3-OP7 or the reading of the ISR.

CTUR and CTLR – Counter/Timer Registers

The CTUR and CTLR hold the eight MSBs and eight LSBs, respectively, of the value to be used by the counter/timer in either the counter or timer modes of operation. The minimum value which may be loaded into the CTUR/CTLR registers is 000216. Note that these registers are write-only and cannot be read by the CPU.

In the timer (programmable divider) mode, the C/T generates a square wave with a period of twice the value (in clock periods) of the CTUR and CTLR. If the value in CTUR and CTLR is changed, the current half-period will not be affected, but subsequent half periods will be. In this mode the C/T runs continuously. Receipt of a start counter command (read with A4-A1) = 1110) causes the counter to terminate the current timing cycle and to begin a new cycle using the values in CTUR and CTLR. The waveform so generated is often used for a data clock. The formula for calculating the divisor n to load to the CTUR and CTLR for a particular 1X data clock is shown below:

CT Clock Frequency

n 

2  16  Baud rate desired

Often this division will result in a non-integer number; 26.3, for

example. One can only program integer numbers in a digital divider.

Therefore, 26 would be chosen. This gives a baud rate error of

0.3/26.3 which is 1.14%; well within the ability asynchronous mode of operation.

The counter ready status bit (ISR[3]) is set once each cycle of the square wave. The bit is reset by a stop counter command (read with A4-A1 = 111 1). The command, however, does not stop the C/T. The generated square wave is output on OP3 if it is programmed to be the C/T output.

On power-up and after reset, the counter/timer runs in timer mode and can only be restarted. Because it cannot be shut off or stopped, and runs continuously in timer mode, it is recommended that at initialization, the output port, OP3, should be masked off through the OPCR[3:2} = 00 until the C/T is programmed to the desired operational state.

1998 Sep 04

Page 18

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

In the counter mode, the C/T counts down the number of pulses loaded into CTUR and CTLR by the CPU. Counting begins upon receipt of a start counter command. Upon reaching terminal count

, the counter ready interrupt bit (ISR[3]) is set. The counter

0000

continues counting past the terminal count until stopped by the CPU.

If OP3 is programmed to be the output of the C/T, the output remains High until terminal count is reached, at which time it goes Low. The output returns to the High state and ISR[3] is cleared when the counter is stopped by a stop counter command. The CPU may change the values of CTUR and CTLR at any time, but the new count becomes effective only on the next start counter commands. If new values have not been loaded, the previous count values are preserved and used for the next count cycle

In the counter mode, the current value of the upper and lower 8 bits of the counter (CTU, CTL) may be read by the CPU. It is recommended that the counter be stopped when reading to prevent potential problems which may occur if a carry from the lower 8 bits to the upper 8 bits occurs between the times that both halves of the counter are read. However, note that a subsequent start counter command will cause the counter to begin a new count cycle using the values in CTUR and CTLR.

IVR – Interrupt Vector Register

This register contains the interrupt vector. The register is initialized to H‘0F’ by RESET. The contents of the register are placed on the data bus when the DUART responds to a valid interrupt acknowledge cycle.

1998 Sep 04

Page 19

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

RESETN

RES

SD00109

Figure 3. Reset Timing

CSC

X1/CLK

A1–A4

RWN

CSN

D0–D7

DTACKN

X1/CLK

A1–A4

RWN

CSN

RWS

DAL

DCR

Figure 4. Bus Timing (Read Cycle)

CSC

RWS

CSD

DAT

CSW

RWH

DAH

RWH

SD00110

D0–D7

DTACKN

NOTE:

DACKN requires two rising edges of X1 clock after CEN is low.

1998 Sep 04

DCW

CSD

Figure 5. Bus Timing (Write Cycle)

DAT

DAH

SD00111

Page 20

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

X1/CLK

INTRN

IACKN

CSC

DAH

DAT

SD00112

D0–D7

DTACKN

CSD

DAL

DCR

Figure 6. Interrupt Cycle Timing

CSN

IP0–IP5

CSN

OP0–OP7

OLD DATA

NEW DATA

1998 Sep 04

RxC

(1X INPUT)

RxD

Figure 7. Port Timing

RXS

RXH

Figure 8. Receive Timing

SD00113

SD00114

Page 21

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

CLK

CTC

X1/CLK CTCLK

RxC TxC

When using an external clock it is preferred to drive X2 and leave X1 open. X2 is the input to the internal driver, while X1 is the output. R1 is only required if U1 will not drive to X2 high level. Previous specifications indicated X2 should be grounded and X1 should be driven. This is still acceptable. It is electrically easier to drive the amplifier input than to overdrive its output.

CLK

CTC

DRIVING FROM

EXTERNAL SOURCE

R1: 100K - 1Meg (See design note) C1 = C2: 0-5pF + (STRAY < 5pF)

OPEN

1KΩ

+5V

3.6864MHz

CRYSTAL SERIES RESISTANCE3 SHOULD BE LESS THAN 180Ω

R2 = 50kΩ to 150kΩ

74LS04

SCN2681

+5V

TO THE REST OF THE DUART CIRCUITS

Figure 9. Clock Timing

CSN

(READ OR

WRITE)

INTERRUPT

NOTES:

1. INTRN or OP3 – OP7 when used as interrupt outputs.

2. The test for open drain outputs is intended to guarantee switching of the output transistor. Measurement of this response is referenced from the mid point of the switching signal, V a point 0.5 volts above V pronounced and can greatly affect the resultant measurement.

. This point represents noise margin that assures true switching has occurred. Beyond this level, the effects of external circuitry and test environment are

OUTPUT

+0.5V

CLOCK TO OTHER CHIPS

SD00115

SD00116

, to

TxC

(INPUT)

TxC

(1X OUTPUT)

Figure 10. Interrupt Timing

1 BIT TIME

(1 OR 16 CLOCKS)

TXD

TxD

TCS

Figure 11. Transmit Timing

SD00117

1998 Sep 04

Page 22

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

RxC

(1X INPUT)

TxD D1 D2 D3 D4 D6BREAK

TRANSMITTER

ENABLED

TxRDY

(SR2)

CSN

(WRITE)

CTSN

(IP0)

RTSN

(OP0)

NOTES:

1. Timing shown for MR2(4) = 1.

2. Timing shown for MR2(5) = 1.

RxD

RXS

RXH

SD00093

Figure 12. Receive Timing

D1 D2 D3 D4 D6START

OPR(0) = 1 OPR(0) = 1

BREAK

STOP

BREAK

D5 WILL NOT BE

TRANSMITTED

Figure 13. Transmitter Timing

SD00118

RxD

RECEIVER

ENABLED

RxRDY

(SR0)

FFULL

(SR1)

RxRDY/

FFULL

(OP4)

CSN

(READ)

OVERRUN

(SR4)

RTS

(OP0)

NOTES:

1. Timing shown for MR1(7) = 1.

2. Shown for OPCR(4) and MR1(6) = 0.

1998 Sep 04

D1 D2 D3 D4 D5 D6 D7 D8

D6, D7, D8 WILL BE LOST

STATUS DATA

OPR(0) = 1

STATUS DATAD2STATUS DATAD3STATUS DATA

D5 WILL BE LOST

Figure 14. Receive Timing

RESET BY COMMAND

SD00119

Page 23

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

TxD

TRANSMITTER

ENABLED

TxRDY

(SR2)

CSN

(WRITE)

RxD

RECEIVER

ENABLED

RxRDY

(SR0)

CSN

MASTER STATION

MR1(4+3) = 11

MR1(2) = 1

PERIPHERAL STATION

MR1(4:3) = 11 ADD#1

ADD#1MR1(2) = 0 D0 MR1(2) = 1 ADD#2

BIT 9

ADD#1

ADD#1 1

BIT 9

D0 0

BIT 9

Figure 15. Wake-Up Mode

BIT 9

D0 0

BIT 9

STATUS DATA

ADD#2 1

BIT 9

STATUS DATA

ADD#2

SD00120

Output Port Notes

The output ports are controlled from three places: the OPCR register, the OPR register, and the MR registers. The OPCR register controls the source of the data for the output ports OP2 through OP7. The data source for output ports OP0 and OP1 is controlled by the MR and CR registers. When the OPR is the source of the data for the output ports, the data at the ports is inverted from that in the OPR register. The content of the OPR register is controlled by the “Set Output Port Bits Command”. These commands are at E and F, respectively. When these commands are used, action takes place only at the bit locations where ones exist. For example, a one in bit location 5 of the data word used with the

“Set Output Port Bits” command will result in OPR5 being set to one.

The OP5 would then be set to zero (V

). Similarly, a one in bit

position 5 of the data word associated with the “Reset Output Ports Bits” command would set OPR5 to zero, and hence, the pin OP5 to a one (V

The CTS, RTS, CTS Enable Tx signals

CTS (Clear To Send) is usually meant to be a signal to the transmitter meaning that it may transmit data to the receiver. The CTS input is on pin MPI. The CTS signal is active low; thus, it is called CTS.

RTS is usually meant to be a signal from the receiver indicating that the receiver is ready to receive data. It is also active low and is, thus, called RTSN. RTSN is on pin MP0. A receiver’s RTS output will usually be connected to the CTS input of the associated transmitter. Therefore, one could say that RTS and CTS are different ends of the same wire!

MR2(4) is the bit that allows the transmitter to be controlled by the CTS pin (MPI). When this bit is set to one AND the CTS input is

driven high, the transmitter will stop sending data at the end of the present character being serialized. It is usually the RTS output of the receiver that will be connected to the transmitter’s CTS input. The receiver will set RTS high when the receiver FIFO is full AND the start bit of the fourth character is sensed. Transmission then stops with four valid characters in the receiver. When MR2(4) is set to one, CTSN must be at zero for the transmitter to operate. If MR2(4) is set to zero, the MP pin will have no effect on the operation of the transmitter.

MR1(7) is the bit that allows the receiver to control MP0. When MP0 is controlled by the receiver, the meaning of that pin will be RTS. However, a point of confusion arises in that MP0 may also be controlled by the transmitter. When the transmitter is controlling this pin, its meaning is not RTS at all. It is, rather, that the transmitter has finished sending its last data byte. Programming the MP0 pin to be controlled by the receiver and the transmitter at the same time is allowed, but would usually be incompatible.

RTS is expressed at the MP0 pin which is still an output port. Therefore, the state of MP0 should be set low for the receiver to generate the proper RTS signal. The logic at the output is basically a NAND of the MP0 bit register and the RTS signal as generated by the receiver. When the R TS flow control is selected via the MR(7) bit the state of the MP0 register is not changed. Terminating the use of “Flow Control” (via the MR registers) will return the MP0 pin to the control of the MP0 register.

Transmitter Disable Note

The sequence of instructions enable transmitter — load transmit holding register — disable transmitter will result in nothing being sent if the time between the end of loading the transmit holding register and the disable command is less that 3/16 bit time in the

1998 Sep 04

Page 24

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

16x mode or one bit time in the 1x mode. Also, if the transmitter, while in the enabled state and underrun condition, is immediately disabled after a single character is loaded to the transmit holding register, that character will not be sent.

In general, when it is desired to disable the transmitter before the last character is sent AND the TxEMT bit is set in the status register (TxEMT is always set if the transmitter has underrun or has just

been enabled), be sure the TxRDY bit is active immediately before issuing the transmitter disable instruction. TxRDY sets at the end of the “start bit” time. It is during the start bit that the data in the transmit holding register is transferred to the transmit shift register.

Non-standard baud rates are available as shown in Table 6 below, via the BRG Test function.

Table 6. Baud Rates Extended

Normal BRG BRG Test

CSR[7:4] ACR[7] = 0 ACR[7] = 1 ACR[7] = 0 ACR[7] = 1

0000 50 75 4,800 7,200 0001 110 110 880 880 0010 134.5 134.5 1,076 1,076 0011 200 150 19.2K 14.4K 0100 300 300 28.8K 28.8K 0101 600 600 57.6K 57.6K 0110 1,200 1,200 115.2K 115.2K 0111 1,050 2,000 1,050 2,000 1000 2,400 2,400 57.6K 57.6K 1001 4,800 4,800 4,800 4,800 1010 7,200 1,800 57.6K 14.4K 1011 9,600 9,600 9,600 9,600 1100 38.4K 19.2K 38.4K 19.2K 1101 Timer Timer Timer Timer 1110 I/O2 – 16X I/O2 – 16X I/O2 – 16X I/O2 – 16X 1111 I/O2 – 1X I/O2 – 1X I/O2 – 1X I/O2 – 1X

NOTE: Each read on address H‘2’ will toggle the baud rate test mode. When in the BRG test mode, the baud rates change as shown to the left. This change affects all receivers and transmitters on the DUART. See

SCC68681 and SCC2698B”

The test mode at address H‘A’ changes all transmitters and receivers to the 1x mode and connects the output ports to some internal nodes.

in application notes elsewhere in this publication.

“Extended baud rates for SCN2681, SCN68681, SCC2691, SCC2692,

A condition that occurs infrequently has been observed where the receiver will ignore all data. It is caused by a corruption of the start bit generally due to noise. When this occurs the receiver will appear to be asleep or locked up. The receiver must be reset for the UART to continue to function properly.

Reset in the Normal Mode (Receiver Enabled)

Recovery can be accomplished easily by issuing a receiver software reset followed by a receiver enable. All receiver data, status and programming will be preserved and available before reset. The reset will NOT affect the programming.

Reset in the Wake-Up Mode (MR1[4:3] = 11)

Recovery can also be accomplished easily by first exiting the wake-up mode (MR1[4:3] = 00 or 01 or 10), then issuing a receiver software reset followed by a wake-up re-entry (MR1[4:3] = 11). All receiver data, status and programming will be preserved and available before reset. The reset will NOT affect the programming.

The receiver has a digital filter designed to reject “noisy” data transitions and the receiver state machine was designed to reject noisy start bits or noise that might be considered a start bit. In spite of these precautions, corruption of the start bit can occur in 15ns window approximately 100ns prior to the rising edge of the data clock. The probability of this occurring is less than 10

A corrupted start bit may have some deleterious effects in ASYNC operation if it occurs within a normal data block. The receiver will tend to align its data clock to the next ‘0’ bit in the data stream, thus potentially corrupting the remainder of the data block. A good design practice, in environments where start bit corruption is possible, is to monitor data quality (framing error, parity error, break change and received break) and “data stopped” time out periods. Time out periods can be enabled using the counter/timer in the SCC2691, SCC2692, SCC2698B and SC68692 products. This monitoring can indicate a potential start bit corruption problem.

1998 Sep 04

–5

at 9600 baud.

SD00097

Page 25

1998 Sep 04

853–0590B 06688

0590B 40-PIN (600 mils wide) CERAMIC DUAL IN-LINE (F) PACKAGE (WITH WINDOW (FA) PACKAGE)

Philips Semiconductors Product specification

– E –

PIN # 1

– D –

– T –

SEATING

PLANE

0.098 (2.49)

0.040 (1.02)

0.100 (2.54) BSC

0.070 (1.78)

0.050 (1.27)

0.023 (0.58)

0.015 (0.38)

2.087 (53.01)

2.038 (51.77)

0.010 (0.254)TED

SEE NOTE 6

0.098 (2.49)

0.040 (1.02)

0.598 (15.19)

0.571 (14.50)

0.225 (5.72) MAX.

0.165 (4.19)

0.125 (3.18)

NOTES:

1. Controlling dimension: Inches. Millimeters are shown in parentheses.

2. Dimension and tolerancing per ANSI Y14. 5M-1982.

3. “T”, “D”, and “E” are reference datums on the body and include allowance for glass overrun and meniscus on the seal line, and lid to base mismatch.

4. These dimensions measured with the leads constrained to be perpendicular to plane T.

5. Pin numbers start with Pin #1 and continue counterclockwise to Pin #40 when viewed from the top.

6. Denotes window location for EPROM products.

0.620 (15.75)

0.590 (14.99) (NOTE 4)

0.175 (4.45)

0.145 (3.68)

0.055 (1.40)

0.020 (0.51)

0.015 (0.38)

0.010 (0.25)

BSC

0.600 (15.24) (NOTE 4)

0.695 (17.65)

0.600 (15.24)

SCN68681Dual asynchronous receiver/transmitter (DUART)

Page 26

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

DIP40: plastic dual in-line package; 40 leads (600 mil) SOT129-1

1998 Sep 04

Page 27

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

PLCC44: plastic leaded chip carrier; 44 leads SOT187-2

1998 Sep 04

Page 28

Philips Semiconductors Product specification

SCN68681Dual asynchronous receiver/transmitter (DUART)

Data sheet status

Objective specification

Preliminary specification

Product specification

Product status

Development

Qualification

Production

Definition

This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice.

This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product.

This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.

[1]

[1] Please consult the most recently issued datasheet before initiating or completing a design.

Definitions

Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For

detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one

or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.

Disclaimers

Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can

reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.

Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.

Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381

 Copyright Philips Electronics North America Corporation 1998

Date of release: 09-98

Document order number: 9397 750 04364

 

1998 Sep 04

Datasheet SCN68681E1A44, SCN68681E1N40, SCN68681C1A44 Datasheet (Philips)

Specifications and Main Features

Frequently Asked Questions

User Manual