Page 1
TOSHIBA RF POWER AMPLIFIER MODULE
r
r
y
t
y
r
S−AU68M
UHF BAND FM POWER AMPLIFIER MODULE
MAXIMUM RATINGS
CHARACTERISTIC SYMBOL RATING UNIT
DC Supply Voltage VDD 7 V
DC Supply Voltage VGG 6 V
Input Power Pi 50 mW
Output Power Po 2 W
Total Current IT 3 A
Operating Case Temperature Range T
Storage Temperature Range T
(Tc=25°C)
30~00 °C
c (opr)
40~0 °C
stg
JEDEC —
EIAJ —
TOSHIBA 523E
Weight: 3.5g
SAU68M
Unit in mm
000707EAA
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general
can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the
buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and
to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury o
damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the
most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling
Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal
equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are
neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction o
failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energ
control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control
instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this documen
shall be made at the customer’s own risk.
· The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed b
TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its
use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION o
others.
· The information contained herein is subject to change without notice.
200-02-02 /4
Page 2
SAU68M
ELECTRICAL CHARACTERISTICS
CHARACTERISTIC SYMBOL TEST CONDITION
Frequency Range f
Output Power () Po () VDD=9.6V 7 — —
Output Power (2) Po (2)
Total Efficiency T 40 — — %
Input VSWR VSWRin — — 2.5 —
Harmonics HRM
Load Mismatch —
Stability —
(Tc=25°C)
— 450 — 470 MHz
range
V
= 4V, Pi = 20mW
GG
Z
=50
G=ZL
= 9.6V, Pi = 20mW
V
DD
P
= 7W (V
o
Z
= ZL = 50
G
= 5V, Pi = 20mW
V
DD
Po = 7W (V
VSWR LOAD 20: ALL PHASE
= 3.5~5.7V, V
V
DD
Po<2W, Pi = 20mW
VSWR LOAD 3: ALL PHASE
GG
GG
= adjust)
= adjust)
GG
=6.0V 2.7 — —
V
DD
= 0~4V
MIN. TYP. MAX. UNIT
— — 25 dB
No Degradation —
All spurious output than
60dB below desired
signal
W
—
CAUTION
· This product has intersetting cap. Please pay attention for exceeding stress and foreign matter in your application.
And not to take away the cap.
· Do not intermingle with normal industrial or domestic waste.
· This product is electrostatic sensitivity, please handle with caution.
200-02-02 2/4
Page 3
SCHEMATIC
SAU68M
TEST FIXTURE
200-02-02 3/4
Page 4
SAU68M
CAUTION
These are only typical curves and devices are not necessarily guaranteed at these curves.
200-02-02 4/4
Loading...