Page 1
Aluminum Electrolytic Capacitors
Features
‧
105℃, 8,000 ~ 10,000 hours assured
‧
Suitable for switching power supplies, UPS, Ballast
‧
Smaller case size current
‧
RoHS Compliance
SPECIFICATIONS
Items Performance
Category Temperature Range 160 ~ 400V 450V
Capacitance Tolerance
Time after 5 minutes
Leakage Current (at 20℃)
Where, C = rated capacitance in µF V = rated DC working voltage in V
Dissipation Factor Rated Voltage 160 200 250 350 400 450
(Tanδat 120Hz, 20℃)
Low Temperature Rated Voltage 160 200 250 350 400 450
Characteristics (at 120Hz) Impedance
Ratio
Test Time
Endurance Capacitance Change Within ±20% of initial value
Dissipation Factor Less than 200% of specified value
Leakage Current Within specified value
Test Time 1,000 Hrs
Capacitance Change With in ±20% of initial value
Dissipation Factor Less than 200% of specified value
Shelf Life Test Leakage Current Less than 500% of specified value
Ripple Current &
Frequency Multipliers 6.8 ~ 82 1.00 1.75 2.25 2.50
100 up 1.00 1.67 2.05 2.25
Leakage Current
* The above specifications shall be satisfied when the capacitors are restored to 20°C after the rated voltage
applied with rated ripple current for 8,000 / 10,000 hours at 105°C.
* The above specifications shall be satisfied when the capacitors are restored to 20°C after exposing them for 1,000
hours at 105°C without voltage applied. The rated voltage shall be applied to the capacitors before the
measurements (Refer to JIS C 5101-4 4.1).
-40℃ ~ +105℃ -25℃ ~ +105℃
Tanδ(max)
Impedance ratio shall not exceed the values given in the table below.
Cap. (μF)
0.20 0.20 0.20 0.24 0.24 0.24
Z(-25)/Z(+20℃)
Z(-40)/Z(+20℃)
Frequency (Hz)
Sleeve & Marking Color: Black & Golden
±20% (at 120Hz, 20℃)
CV ≦ 1,000
I = 0.03CV＋15(µA)
3 3 3 5 5 6
6 6 6 6 6 -
8,000 Hrs for φD = 10mm;
10,000 Hrs for φD ≥ 12.5mm
120 1k 10k 100k up
CV ＞ 1,000
I = 0.02CV＋25(µA)
RXQ
2011 Version
Page 2
Aluminum Electrolytic Capacitors
RXQ
DIAGRAM OF DIMENSIONS
Unit: mm
Vent 10
≧
LEAD SPACING AND DIAMETER
φ
L+α max
Sleeve
DIMENSION & PERMISSIBLE RIPPLE CURRENT
V.DC
Contents
µ
F
6.8 10×16 110 275 10×16 110 275
10 10×16 125 313 10×16 125 313 10×20 140 350 10×20 140 350 10×20 140 350
22 10×20 200 500 10×20 200 500 10×20 200 500 12.5×20 260 650 12.5×20 260 650
33 10×20 250 625 10×20 260 650 12.5×20 320 800 16×20 360 900 16×20 360 900
47 10×20 300 750 12.5×20 390 975 12.5×20 390 975 16×20 430 1,075
68 12.5×20 470 1,175 12.5×20 470 1,175 16×20 520 1,300
82 12.5×20 510 1,275 16×20 550 1,375 16×20 550 1,375 18×25 610 1,525
100
120 18×31.5 830 1,868 18×35.5 865 1,946
150 16×20 770 1,733 16×25 840 1,890 18×25 860 1,935 18×35.5 960 2,160 18×40 985 2,216
220 16×25 1,020 2,295 18×25 1,050 2,363 18×31.5 1,130 2,543
330 18×31.5 1,390 3,128 18×35.5 1,430 3,218
V.DC
Contents
µ
F
6.8 10×20 110 275
10 12.5×20 180 450
22 16×20 290 725
33
47 18×25 480 1,200
68 18×31.5 630 1,575
82 18×35.5 715 1,788
100 18×40 800 1,800
Remark: The case size of 16×20, 18×20 and 18×25 are used flat type rubber bung
160V (2C) 200V (2D) 250V (2E) 350V (2V) 400V (2G)
φD×L
12.5×25
16×20
φD×L
16×25
18×20
Ripple Current
120 Hz 100k Hz 120 Hz 100k Hz 120 Hz 100k Hz 120 Hz 100k Hz 120 Hz 100k Hz
620
630
450V (2W)
Ripple Current
120 Hz 100k Hz
390
380
φD×L
1,395
16×20 630 1,418 16×25 680 1,530 18×25 700 1,575 18×31.5 765 1,721
1,418
975
950
d
φ
15 min
Ripple Current
φD+β
4 min
max
φD
φd
α
0.5
±
P
β
10 12.5 16 18
P 5.0 7.5
0.6 0.8
1.5
0.5
Dimension: φD × L(mm)
Ripple Current: mA/rms at 105°C
φD×L
Ripple Current
φD×L
16×25
18×20
Ripple Current
560
1,400
550
1,375
φD×L
16×25
18×20
18×25 585 1,463
18×25 610 1,525
Ripple Current
470
1,175
450
1,125
2011 Verison
Loading...