Page 1
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised April 7, 2000
Page 1
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
Description
K Positive supply voltage of 3.5 V, nominal
K Efficiency of 36%, typical, for CDMA average power out of 29 dBm
K Small outline quad package
Features
The RMPA1902-58 is a monolithic high efficiency power amplifier for PCS CDMA personal communication system
applications. The MMIC requires off-chip matching. The amplifier circuit design is a single ended configuration that
utilizes harmonic tuning for increased power added efficiency and linearity. The device uses Raytheon’s
Pseudomorphic High Electron Mobility Transistor (pHEMT) process.
Electrical
Characteristics
1
Parameter Min Typ Max Unit
Frequency Range 1850 1910 MHz
Gain (Small Signal) 30 dB
Gain Variation vs Temp -0.02 dB/°C
Noise Power
(1930-1990 MHz)
(All Power Levels) -137 dBm/Hz
Input VSWR (50Ω) 2.0:1 ---
Stability (All spurious)
2
-70dBc
Harmonics
(Po ≤ 29 dBm)
2fo, 3fo, 4fo -40 dBc
Notes:
1. Specifications are valid for Vdd = 3.5V, load = 50 Ω, and Tc = 25°C as measured in Raytheon’s test fixture unless otherwise stated.
2. Source/Load VSWR ≤ 3:1 (All Angles, -50 dBm<Po<29 dBm) or Load VSWR ³ 20:1 (Out of Band, All Angles, Tc=-30 to +90°C).
3. Po ≤ 29.0 dBm at Vdd=3.5V; CDMA Waveform measured using the ratio of the average power within the 1.23 MHz channel and within a 30
kHz bandwidth at a 1.25 MHz offset.
4. Vgg adjusted for quiescent current. I
dq1,2
=50+/-1 mA, I
dq3
=85+/-2 mA
Absolute
Maximum
Ratings
4
Parameter Symbol Value Unit
Positive DC Voltage Vd1,Vd2, Vd3 + 9 Volts
Negative DC Voltage Vg1,Vg2, Vg3 - 6 Volts
Simultaneous (Vd-Vg) Vdg +12 Volts
RF Input Power (from 50-Ohm source) P
IN
+10 dBm
Operating Case Temperature T
C
-30 to +90 °C
Storage Temperature Range T
Stg
-35 to +110 °C
Thermal Resistance (Channel to case) R
jc
+18 °C/W
Parameter Min Typ Max Unit
Power Out 29 dBm
Efficiency at
Pout = 29 dBm 36 %
ACPR
(Offset ≤ ± 1.25 MHz)
3
49 dBc
Noise Figure (over temp.) 5.5 dB
Quiescent Current 135 mA
Vdd 3.5 Volts
Vgg (<4 mA)
4
-2.0 -0.3 Volts
Case Operating Temp -40 +85 °C
RMPA1902A-58
PCS GaAs MMIC Power Amplifier
Page 2
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised April 7, 2000
Page 2
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
CAUTION: THIS IS AN ESD SENSITIVE DEVICE.
The following describes a procedure for evaluating the RMPA1902-58, a monolithic high efficiency power amplifier,
in a surface mount package, designed for use in Personal Communication Systems (PCS) utilizing Code Division
Multiple Access (CDMA). Figure 1 shows the package outline and the pin designations. Figure 2 shows the
functional block diagram of the packaged product. It should be noted that RMPA1902-58 requires external passive
components for DC bias and RF output matching circuits. A recommended schematic circuit is shown in Figure 3.
The gate biases for the three stages of the amplifier may be set by simple resistive voltage dividers. Figure 4 shows
a typical layout of an evaluation board, corresponding to the schematic circuits of Figure 3. The following
designations should be noted:
(4) Vd1 and Vd2 are the Drain Voltages (positive)
applied at the pins of the package
(5) Vdd1 and Vdd2 are the positive supply voltages at
the evaluation board terminals
Note: The 2 terminals of Vdd1 and Vdd2 may be
tied together.
The base of the package must be soldered on to a heat
sink for proper operation.
Figure 1
Package Outline and
Pin Designations
RF Out/Vd3
RF Out/Vd3
RF Out/Vd3
VD1
GND
VG1
RF Input
GND
VG2
VD2
GND
VG3
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
DescriptionPin #
Dimensions in inches
10
11
1
2
3
456
7
8
9
12
BOTTOM VIEWTOP VIEW
10
11
0.030
A
0.015
1
2
3
456
7
8
9
12
0.200 SQ.
RAY
RMPA
1902A
0.041
13
PLASTIC LID
SIDE SECTION
0.069 MAX.
0.010
0.230
0.246
0.282
Application
Information
(1) Pin designations are as shown in Figure 2.
(2) Vg1 and Vg2 are the Gate Voltages (negative)
applied at the pins of the package
(3) Vgg1 and Vgg2 are the negative supply voltages at
the evaluation board terminals
Note: The 3 terminals of Vgg1, Vgg2 and Vgg3 may
be tied together.
Figure 2
Functional Block
Diagram of
Packaged Product
RF IN
Pin# 7
Vg1
Pin# 6
Vg2
Pin# 9
Vd1
Pin# 4
Vd2
Pin# 10
GND
Pins# 5, 8, 11, 13
Vg3
Pin#12
RF OUT & Vd3
Pins# 1, 2, 3
RMPA1902A-58
PCS GaAs MMIC Power Amplifier
Page 3
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised April 7, 2000
Page 3
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
Figure 3
Schematic of
Application Circuit
showing external
components
Figure 4
Layout of Test
Evaluation Board
(RMPA1902-58-TB)
RMPA1902A-58
PCS GaAs MMIC Power Amplifier
Page 4
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised April 7, 2000
Page 4
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
CAUTION: LOSS OF GATE VOLTAGES (VG1, VG2, VG3) WHILE CORRESPONDING DRAIN VOLTAGES
(VD1,VD2,VD3) ARE PRESENT MAY DAMAGE THE AMPLIFIER.
The following sequence must be followed to properly test the amplifier:
Test Procedure
for the
evaluation board
(RMPA1902-58-TB)
Step 1: Turn off RF input power.
Step 2: Use GND terminal of the evaluation board
for the ground of the DC supplies.
Slowly apply gate supply voltages of typical
-2.0 V to the board terminals
Vgg=Vgg1=Vgg2=Vgg3
Step 3: Slowly apply drain supply voltages of +3.5 V to
the board terminals Vdd=Vdd1=Vdd2=Vdd.
Adjust Vgg to set the total quiescent current
(with no RF applied) Idq to nominal 135 mA.
[Gate supply voltages (Vgg i.e. Vgg1, Vgg2,
Vgg3) may be adjusted, only if quiescent
current (Idq1 to Idq3) values desired are
different from those noted on the data
summary supplied with product samples]
Step 4: After the bias condition is established, RF input
signal may now be applied at the appropriate
frequency band and appropriate power level.
Step 5: Follow turn-off sequence of:
(i) Turn off RF Input Power
(ii) Turn down and off drain voltages
Vdd=Vdd1=Vdd2=Vdd3
(iii) Turn down and off gate voltages
Vgg=Vgg1=Vgg2=Vgg3
RMPA1902A-58
PCS GaAs MMIC Power Amplifier
Page 5
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised April 7, 2000
Page 5
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
D&L Technical Sales
6139 S. Rural Road, #102
Tempe, AZ 85283
480-730-9553
fax: 480-730-9647
Nicholas Delvecchio, Jr.
dlarizona@aol.com
Hi-Peak Technical Sales
P.O. Box 6067
Amherst, NH 03031
866-230-5453
fax: 603-672-9228
sales@hi–peak.com
North
America
Spartech South
2115 Palm Bay Road, NE,
Suite 4
Palm Bay, FL 32904
321-727-8045
fax: 321-727-8086
Jim Morris
jim@spartech-south.com
TEQ Sales, Inc.
920 Davis Road, Suite 304
Elgin, IL 60123
847-742-3767
fax: 847-742-3947
Dennis Culpepper
dculpepper@teqsales.com
Cantec Representatives
8 Strathearn Ave, No. 18
Brampton, Ontario
Canada L6T 4L9
905-791-5922
fax: 905-791-7940
Dave Batten
cantec-ott@cantec-o.net
Sangus OY
Lunkintie 21,
90460 Oulunsalo
Finland
358-8-8251-100
fax: 358-8-8251-110
Juha Virtala
juha.virtala@sangus.fi
ITX Corporation
2–5, Kasumigaseki
3–Chome
Chiyoda–Ku
Tokyo 100-6014 Japan
81-3-4288-7073
fax: 81-3-4288-7243
Maekawa Ryosuke
maekawa.ryosuke@
itx–corp.co.jp
MTI Engineering Ltd.
Afek Industrial Park
Hamelacha 11
New Industrial Area
Rosh Hayin 48091
Israel
972-3-902-5555
fax: 972-3-902-5556
Adi Peleg
adi_p@mti-group.co.il
Sirces srl
Via C. Boncompagni, 3B
20139 Milano
Italy
3902-57404785
fax: 3902-57409243
Nicola Iacovino
nicola.iacovino@sirces.it
Sea Union
9F-1, Building A, No 19-3
San-Chung Road
Nankang Software Park
Taiwan, ROC
Taipei 115
02-2655-3989
fax: 02-2655-3918
Murphy Su
murphy@seaunionweb.com.tw
Globes Elektronik & Co.
Klarastrabe 12
74072 Heilbronn
Germany
49-7131-7810-0
fax: 49-7131-7810-20
Ulrich Blievernicht
hfwelt@globes.de
Headquarters
6321 San Ignacio Drive
San Jose, CA 95119
408-360-4073
fax: 408-281-8802
Art Herbig
art.herbig@avnet.com
Belgium and Luxembourg
Cipalstraat
2440 GEEL
Belgium
32 14 570670
fax: 32 14 570679
sales.be@bfioptilas.avnet.com
United States
(East Coast)
Raytheon
362 Lowell Street
Andover, MA 01810
978-684-8628
fax: 978-684-8646
Walter Shelmet
wshelmet@
rrfc.raytheon.com
Sales Office
Headquarters
978-684-8900 fax: 978-684-5452 customer_support@rrfc.raytheon.com
Customer
Support
Europe
Raytheon
AM Teckenberg 53
40883 Ratingen
Germany
49-2102-706-155
fax: 49-2102-706-156
Peter Hales
peter_j_hales@
raytheon.com
Asia
Raytheon
Room 601, Gook Je Ctr. Bldg
191 Hangang Ro 2-GA
Yongsan-Gu, Seoul,
Korea 140-702
82-2-796-5797
fax: 82-2-796-5790
T.G. Lee
tg_lee@
rrfc.raytheon.com
United States
(West Coast)
Raytheon
362 Lowell Street
Andover, MA 01810
978-684-8919
fax: 978-684-8646
Rob Sinclair
robert_w_sinclair@
rrfc.raytheon.com
United Kingdom
Burnt Ash Road
Aylesford, Kent
England
ME207XB
44 1622882467
fax: 44 1622882469
rfsales.uk@
bfioptilas.avnet.com
France
4 Allee du Cantal
Evry, Cedex
France
33 16079 5900
fax: 33 16079 8903
sales.fr@
bfioptilas.avnet.com
Holland
Chr. Huygensweg 17
2400 AJ ALPHEN AAN DEN
RIJN
The Netherlands
31 172 446060
fax: 33 172 443414
sales.nl@
bfioptilas.avnet.com
Spain
C/Isobel Colbrand, 6 – 4a
28050 Madrid
Spain
34 913588611
fax: 34 913589271
sales.es@
bfioptilas.avnet.com
Europe
Asia
Steward Technology
6990 Village Pkwy #206
Dublin, CA 94568
925-833-7978
fax: 925-560-6522
John Steward
johnsteward1@msn.com
Sangus AB
Berghamnvagen 68
Box 5004
S–165 10 Hasselby
Sweden
Ronny Gustafson
468-0-380210
fax: 468-0-3720954
Worldwide
Distribution
Worldwide Sales
Representatives
Loading...