Datasheet R46KR410000M1M, R46KN322000M1M, R46KI322000M2M, R46 series Specification

Download

Page 1

09/2008

150

Loose Taped

Fig.1 Fig.2

Insulated rigid leads Insulated exible leads 0.5mm

Ø d ±0.05

*See size table. All dimensions are in mm.

p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5

0.6 or 0.8* 0.8 1

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm.

Plates: metal layer deposited by evaporation under vacuum.

Winding: non-inductive type.

tinned wire.

eads:

Protection:

Box material is solvent resistant and ame retardant according to

UL94 V0.

arking:

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/110/56 IEC 60068-1

plastic case, thermosetting resin lled.

Manufacturer’s logo, series, capacitance, tolerance,

Operating temperature range: -40 to +110°C

Related documents: IEC 60384-14, EN 60384-14.

ELECTRICAL CHARACTERISTICS

Rated voltage (V

300Vac (50/60Hz) / 630 Vdc

Capacitance range: 0.01

): 275Vac (50/60Hz) / 560 Vdc

µF to 10µF

Capacitance values: E6 series (IEC 60063 Norm).

Capacitance tolerances (measured at 1 kHz):

±10% (K); ±20% (M);

tolerance

±5% (J) available upon request

Dissipation factor (DF):

tgδ 10-4 at +25°C ±5°C: ≤10 (6)* at 1kHz * Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C Voltage charge time: 1 min Voltage charge: 100 Vdc

Performance

≥1x10

MΩ (5x105 MΩ )* for C≤0.33µF

≥30000 s (150000 s

)

* for C>0.33µF

* Typical value

Test voltage between terminations (on all pieces):

1500Vac for 1 s + 2200Vdc for 1 s at +25°C

±5°C

R.46

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

Typical applications: interference suppression and «across-the-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock.

ODUCT CODE: R46

Not for use in series with the mains. See www.kemet.com for more information.

Note: R.46 series has replaced the 1.40 series and 1.47 series.

For new design we suggest the use of the R.46 series.

Pitch Box thickness (B) Maximum dimensions (mm) (mm) (mm) B max H max L max

10.0 All B +0.2 H +0.1 L +0.2

15.0 <7.5 B +0.2 H +0.1 L +0.3

15.0 ≥7.5 B +0.2 H +0.1 L +0.5

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C ± 2°C Relative humidity (RH): 93% Test duration: 56 days

Test conditions 2nd

Temperature: +60°C ± 2°C Relative humidity (RH): 95% Test duration: 500 hours

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change |

∆C/C|: ≤5%

Insulation resistance:

Endurance:

Test conditions

Temperature: +110°C ± 2°C Test duration: 1000 h Voltage applied: 1.25 x V

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change |

∆C/C|: ≤10%

Insulation resistance:

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C ± 5°C Dipping time (with heat screen):10 s

Performance

Capacitance change |∆C/C|: ≤2%

Winding scheme

single sided metallized

polypropylene lm

±2%

(d.c.)/1 min

≥50% of initial limit.

+1000Vac 0.1 s/h

(d.c.)/1 min

≥50% of initial limit.

± 1 s

Page 2

Rated Cap. 275 Vac / 560 Vdc

0.010 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2100 - - N0

0.015 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2150 - - N0

0.022 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2220 - - N0

0.033 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2330 - - M1

0.047 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2470 - - N0

0.068 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 2680 - - M1

0.10 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3100 - - M1

0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2100 - - 01

0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2150 - - 01

0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2220 - - 01

0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2330 - - 01

0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2470 - - 01

0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2680 - - 01

0.10 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 3100 - - M1

0.15 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3150 - - M2

0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3150 - - L2

0.22 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3220 - - M2

0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3220 - - L2

0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3220 - - 02

0.33 µF 8.5 14.5 18.0 15.0 0.6 400 R46 KI 3330 - - N0

0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3330 - - M1

0.33 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3330 - - N1

0.33 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3330 - - 02

0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 KI 3330 - - 01

0.47 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3470 - - 02

0.47 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3470 - - N0

0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3470 - - M1

0.56 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3560 - - N0

0.60 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3600 - - N0

0.15 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3150 - - 01

0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3220 - - M1

0.33 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3330 - - N0

0.47 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3470 - - N0

0.68 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 3680 - - M2

1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4100 - - N2

1.0 µF 11.0 20.0 26.5 22.5 0.8 200 R46 KN 4100 - - N1

0.47 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3470 - - 01

0.68 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3680 - - M1

1.0 µF 11.0 20.0 32.0 27.5 0.8 150 R46 KR 4100 - - M1

1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46 KR 4150 - - M1

2.2 µF 13.0 25.0 32.0 27.5 0.8 150 R46 KR 4220 - - M2

2.2 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4220 - - M1

3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4330 - - M2

4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4470 - - M2

4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R46 KR 4470 - - M1

1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4150 - - M1

2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4220 - - M2

2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46 KW 4220 - - M1

3.3 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW

4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4470 - - M2

4.7 µF 19.0 32.0 41.5 37.5 1.0 100 R46 KW 4470 - - M1

6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46 KW 4680 - - M2

6.8 µF 24.0 44.0 41.5 37.5 1.0 100 R46 KW 4680 - - M1

10.0 µF 30.0 45.0 41.5 37.5 1.0 100 R46 KW 5100 - - M1

Std dimensions

B H L p

Ø d Max

dv/dt at 390Vdc

(V/

Part

µs)

4330 - - M1 -

Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%)

umber

R.46

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

APPROVALS

ENEC

Approved according to IEC 60384-14

According to IEC 60065

(**) ENEC mark has replaced all the following European

National marks:

Table 1

Note: Ammo-pack is the preferred packaging for taped version.

IEC 60384-14

(**)

1414 (up to 1µF, 85°C; 250Vac)

CSA

- C22.2 No.1 (up to 1µF, 85°C; 250Vac)

1283

UL (310 Vac)

CSA

- C22.2 No.8 (310 Vac)

GB/T 14472 Class X2

Standard

packaging style

AMMO-PACK AMMO-PACK

Ø500mm

REEL

Ø500mm

Loose, short leads Loose, long leads Loose, long leads

Loose, insulated rigid leads

Loose, insulated

exible leads

Class X2 File

Across-the-line File No.E97797

Across-the-line

certied for

Canada

Electromagnetic Interference Filters

Electromagnetic Interference

Filters certied

for Canada

Lead

aping style Ordering

length

(mm)

(No.)

Fig.

12.70

19.0512

12.70

19.0512

-1/+2

±5

150

For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHO CHOOSE THE RIGHT FILM CAPACITORS” at pag. 178 and contact our Technical Service for choosing the safest solution.

No.V4413

File No.E97797

No.E85238

File

File No.E85238

File CQC03001008199 CQC03001008842

Pitch (mm)

10.0/15.0

22.5

10.0/15.0

22.5/27.5

RT GUIDE TO

code

(Digit 10 to

DQ DQ

CK CK

00 50 40

All dimensions are in mm

E12 Series available upon request

151

09/2008

Page 3

09/2008

152

Rated Cap. 275 Vac / 560 Vdc

0.033 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2330 - - P0

0.047 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2470 - - P0

0.068 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2680 - - P0

0.1 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 3100 - - P1

0.1 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3100 - - P0

0.15 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3150 - - P0

0.15 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 3150 - - P0

0.22 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3220 - - P0

0.33 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3330 - - P0

0.33 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3330 - - P1

0.33 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3330 - - P2

0.47 µF 8.5 14.5 18.0 15.0 0.6 400 R46 KI 3470 - - P0

0.47 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3470 - - P1

0.47 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3470 - - P2

0.47 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3470 - - P3

0.68 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3680 - - P1

0.68 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3680 - - P0

0.82 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3820 - - P0

0.47 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3470 - - P1

0.56 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3560 - - P1

0.56 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3560 - - P0

0.68 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3680 - - P0

1.0 µF 8.5 17.0 26.5 22.5 0.8 200 R46 KN 4100 - - P1

1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4100 - - P0

1.5 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4150 - - P1

1.5 µF 11.0 20.0 26.5 22.5 0.8 200 R46 KN 4150 - - P0

2.2 µF 13.0 22.0 26.5 22.5 0.8 200 R46 KN 4220 - - P0

1.0 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 4100 - - P0

1.5 µF 11.0 20.0 32.0 27.5 0.8 150 R46 KR 4150 - - P0

2.2 µF 13.0 22.0 32.0 27.5 0.8 150 R46 KR 4220 - - P0

3.3 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4330 - - P0

4.7 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4470 - - P1

4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4470 - - P0

6.8 µF 22.0 37.0 32.0 27.5 0.8 150 R46 KR 4680 - - P0

2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4220 - - P0

3.3 µF 13.0 24.0 41.5 37.5 1.0 100 R46 KW 4330 - - P0

4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4470 - - P0

6.8 µF 19.0 32.0 41.5 37.5 1.0 100 R46 KW 4680 - - P0

10.0 µF 20.0 40.0 41.5 37.5 1.0 100 R46 KW 5100 - - P0

Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%)

Std dimensions

B H L p (V/ µs)

Ø d Max

dv/dt at 390Vdc

Part

umber

R.46

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

APPROVALS

ENEC IEC 60384-14

(**)

Approved according to IEC 60384-14 According to IEC 60065

Not for use in series with the mains. See www.kemet.com for more information.

. (**) ENEC mark has replaced all the following European

National marks:

Table 1

packaging style

AMMO-PACK AMMO-PACK

REEL

Loose, short leads Loose, long leads Loose, long leads

Loose, insulated rigid leads

Loose, insulated

exible leads

UL 1414 (up to 1µF, 85°C; 250Vac)

- C22.2 No.1

CSA (up to 1µF, 85°C; 250Vac)

1283

UL (310 Vac)

- C22.2 No.8

CSA (310 Vac)

GB/T 14472 Class X2

Standard

Lead

length

(mm)

Ø500mm Ø500mm

-1/+2

±5

150

Note: Ammo-pack is the preferred packaging for taped version.

Class X2 File

Across-the-line File No.E97797

Across-the-line

certied for

File No.E97797

Canada

Electromagnetic Interference

File

Filters

Electromagnetic Interference

Filters certied

File

for Canada

File CQC03001008199 CQC03001008842

aping style Ordering

(mm)

(No.)

12.70

19.0512

12.70

19.0512

Fig.

Pitch (mm)

10.0/15.0

22.5

10.0/15.0

22.5/27.5

No.V4413

No.E85238

code

(Digit

10 to 11)

DQ DQ

CK CK

00 50 40

All dimensions are in mm

E12 Series available upon request

For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHO

RT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS” at pag. 178 and contact our Technical Service for choosing the safest solution.

Page 4

Rated Cap. 300 Vac / 630 Vdc

0.010 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2100 - - N0

0.015 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2150 - - N0

0.022 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2220 - - N0

0.033 µF 5.0 11.0 13.0 10.0 0.6 500 R46 3F 2330 - - M1

0.047 µF 5.0 11.0 13.0 10.0 0.6 500 R46 3F 2470 - - N0

0.068 µF 6.0 12.0 13.0 10.0 0.6 500 R46 3F 2680 - - M1

0.10 µF 6.0 12.0 13.0 10.0 0.6 500 R46 3F 3100 - - M1

0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2100 - - 01

0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2150 - - 01

0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2220 - - 01

0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2330 - - 01

0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2470 - - 01

0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2680 - - 01

0.10 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 3100 - - M1

0.15 µF 6.0 12.0 18.0 15.0 0.6 400 R46 3I 3150 - - M2

0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 3I 3150 - - L2

0.22 µF 7.5 13.5 18.0 15.0 0.6 400 R46 3I 3220 - - M2

0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 3I 3220 - - L2

0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 3I 3220 - - 02

0.33 µF 8.5 14.5 18.0 15.0 0.6 400 R46 3I 3330 - - N0

0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 3I 3330 - - M1

0.33 µF 7.5 18.5 18.0 15.0 0.8 400 R46 3I 3330 - - 02

0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 3I 3330 - - 01

0.47 µF 10.0 16.0 18.0 15.0 0.8 400 R46 3I 3470 - - N0

0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3470 - - M1

0.56 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3560 - - N0

0.60 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3600 - - N0

0.15 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3150 - - 01

0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3220 - - M1

0.33 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3330 - - N0

0.47 µF 7.0 16.0 26.5 22.5 0.8 200 R46 3N 3470 - - N0

0.68 µF 10.0 18.5 26.5 22.5 0.8 200 R46 3N 3680 - - M2

1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 3N 4100 - - N2

1.0 µF 11.0 20.0 26.5 22.5 0.8 200 R46 3N 4100 - - N1

0.47 µF 9.0 17.0 32.0 27.5 0.8 150 R46 3R 3470 - - 01

0.68 µF 9.0 17.0 32.0 27.5 0.8 150 R46 3R 3680 - - M1

1.0 µF 11.0 20.0 32.0 27.5 0.8 150 R46 3R 4100 - - M1

1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46 3R 4150 - - M1

2.2 µF 13.0 25.0 32.0 27.5 0.8 150 R46 3R 4220 - - M2

2.2 µF 14.0 28.0 32.0 27.5 0.8 150 R46 3R 4220 - - M1

3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R46 3R 4330 - - M2

4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 3R 4470 - - M2

4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R46 3R 4470 - - M1

1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46 3W 4150 - - M1

2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 3W 4220 - - M2

2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46 3W 4220 - - M1

3.3 µF 16.0 28.5 41.5 37.5 1.0 100 R46 3W 4330 - - M1

4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 3W 4470 - - M2

4.7 µF 19.0 32.0 41.5 37.5 1.0 100 R46 3W

6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46 3W 4680 - - M2

6.8 µF 24.0 44.0 41.5 37.5 1.0 100 R46 3W 4680 - - M1

10.0 µF 30.0 45.0 41.5 37.5 1.0 100 R46 3W 5100 - - M1

Std dimensions

B H L p

Ø d Max

dv/dt at 390Vdc

(V/

Part

µs)

4470 - - M1 -

Rated voltage (3=300Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%)

umber

R.46

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

Not for use in series with the mains.

APPROVALS

Approved according to IEC 60384-14

According to IEC 60065

(**) ENEC mark has replaced all the following European

National marks:

Table 1

AMMO-PACK

REEL

Loose, short leads

Loose, long leads

Loose, insulated

rigid leads

Loose, insulated

exible leads

Note: Ammo-pack is the preferred packaging for taped version.

ENEC IEC 60384-14

(**)

1414 (up to 1µF, 85°C; 250Vac)

CSA

- C22.2 No.1 (up to 1µF, 85°C; 250Vac)

1283

UL (310 Vac)

- C22.2 No.8

CSA (310 Vac)

GB/T 14472 Class X2

Standard

packaging style

Ø500mm Ø500mm

See www.kemet.com for more information.

No.V4413

File No.E97797

File No.E85238

FileCQC03001008199 CQC03001008842

Pitch (mm)

10.0/15.0

22.5

10.0/15.0

22.5/27.5

Lead

length

(mm)

25 30

150

Class X2 File

Across-the-line File No.E97797

Across-the-line

certied for

Canada

Electromagnetic Interference Filters

Electromagnetic Interference

Filters certied for

Canada

aping style Ordering

Fig.

(mm)

(No.)

12.70

19.0512

12.70

19.0512

-1/+2

±5

(Digit

code

10 to 11)

DQ DQ

CK CK

00 50 40

All dimensions are in mm

E12 Series available upon request

For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS” at pag. 178 and contact our Technical Service for choosing the safest solution.

153

09/2008

Page 5

09/2008

154

NEW 125°C

Loose Taped

Ø d ±0.05

p ≤15 p = 22.5

0.6 or 0.8* 0.8

*See size table. All dimensions are in mm.

Fig.1 Fig.2

R.46

X2 CLASS (IEC 60384-14) - MKP

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

Typical applications: interference suppression and «acrossthe-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock.

ODUCT CODE: R46

Not for use in series with the mains. See www.kemet.com for more information.

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm. Plates: metal layer deposited by evaporation under vacuum. Winding: non-inductive type. L

eads:

tinned wire.

Protection: plastic case, thermosetting resin lled. Box material is solvent resistant and ame retardant according to UL94 V0.

Marking:

Manufacturer’s logo, series, capacitance, tolerance,

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/125/56 IEC 60068-1 Operating temperature range:

-40 to +125°C

Related documents: IEC 60384-14; EN 60384-14

ELECTRICAL CHARACTERISTICS

Rated voltage (VR): 275 Vac (50/60Hz) / 560 Vdc Capacitance range: 0.01µF to 1µF

TEST METHOD AND PERFORMANCE Endurance:

Test conditions

Temperature: +125°C±2°C Test duration:

Voltage applied: 1.25 x V

1000 h

+1000Vac 0.1 s/h

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change |∆C/C|: ≤ 10% Insulation resistance: ≥

PPR

OVALS

ENEC IEC 60384-14

(**)

1414 (up to 1µF, 85°C; 250Vac)

- C22.2 No.1

CSA (up to 1µF, 85°C; 250Vac)

1283 (310 Vac)

CSA

- C22.2 No.8

(310 Vac)

(d.c.)/1 min

50% of initial limit.

Class X2 File

Across-the-line File No.E97797

Across-the-line

certied for

Canada

Electromagnetic Interference Filters

Electromagnetic Interference

Filters certied

for Canada

File

No.CA08.00063

No.E97797

No.E85238

Approved according to IEC 60384-14 According to IEC 60065

(**) ENEC mark has replaced all the following European National marks:

Ø d

M dv/dt at 390Vdc

µs)

(V/

Part Number

275 Vac / 560 Vdc

Rated

Cap.

0.010

µF 5.0 11.0 13.0 10.0 0.6 500 R46 K F 2100 - - H1

0.015 µF 5.0 11.0 13.0 10.0 0.6 500 R46 K F 2150 - - H1

0.022 µF 5.0 11.0 13.0 10.0 0.6 500 R46 K F 2220 - - H1

0.033 µF 5.0 11.0 13.0 10.0 0.6 500 R46 K F 2330 - - H1

0.047 µF 6.0 12.0 13.0 10.0 0.6 500 R46 K F 2470 - - H1

0.068 µF 6.0 12.0 13.0 10.0 0.6 500 R46 K F 2680 - - H1

0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2100 - - H1

0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2150 - - H1

0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2220 - - H1

0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2330 - - H1

0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2470 - - H1

0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 K I 2680 - - H1

0.10 µF 6.0 12.0 18.0 15.0 0.6 400 R46 K I 3100 - - H1

0.15 µF 6.0 17.5 18.0 15.0 0.6 400 R46 K I 3150 - - H2

0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 K I 3150 - - H3

0.15 µF 7.5 13.5 18.0 15.0 0.6 400 R46 K I 3150 - - H1

0.22 µF 8.5 14.5 18.0 15.0 0.6 400 R46 K I 3220 - - H1

0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 K I 3220 - - H2

0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 K I 3220 - - H3

0.22 µF 7.5 18.5 18.0 15.0 0.8 400 R46 K I 3220 - - H4

0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 K I 3330 - - H1

0.33 µF 7.5 18.5 18.0 15.0 0.8 400 R46 K I 3330 - - H2

0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 K I 3330 - - H3

0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 K I 3470 - - H1

0.15 µF 6.0 15.0 26.5 22.5 0.8 200 R46 K N 3150 - - H1

0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 K N 3220 - - H1

0.33 µF 7.0 16.0 26.5 22.5 0.8 200 R46 K N 3330 - - H1

0.47 µF 10.0 18.5 26.5 22.5 0.8 200 R46 K N 3470 - - H1

0.68 µF 11.0 20.0 26.5 22.5 0.8 200 R46 K N 3680 - - H1

1.0 µF 13.0 22.0 26.5 22.5 0.8 200 R46 K N 4100 - - H1

Std dimensions

B H L p

Rated voltage (K=275Vac) Mechanical version and packaging (Table 1)

Tolerance: K (±10%); M (±20%)

300Vac available upon request E12 Series available upon request

All dimensions are in mm

Page 6

Loose Taped

Ø d ±0.05

*See size table. All dimensions are in mm.

p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5

0.6 or 0.8* 0.8 1.0

Fig.1 Fig.2

R.46 SVERSION

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

Typical applications: This special R46 release is designed for applications in series with the main .

DUCT CODE: R46

PRO

Not for use in series with the mains. See www.kemet.com for more information.

Pitch Box thickness (B) Maximum dimensions (mm)

(mm) (mm) B max H max L max

10.0 All B +0.2 H +0.1 L +0.2

15.0 <7.5 B +0.2 H +0.1 L +0.3

15.0 ≥7.5 B +0.2 H +0.1 L +0.5

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm.

Plates: metal layer deposited by evaporation under vacuum.

Winding: non-inductive type.

tinned wire.

eads:

L Protection: plastic case, thermosetting resin lled.

Box material is solvent resistant and ame retardant according to

UL94 V0.

Marking:

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/110/56 IEC 60068-1

Manufacturer’s logo, series, capacitance, tolerance,

Operating temperature range: -40 to +110°C

Related documents: IEC 60384-14, EN 60384-14.

ELECTRICAL CHARACTERISTICS

Rated voltage (V

Capacitance range: 0.022

): 275Vac (50/60Hz) / 560 Vdc

µF to 10µF

Capacitance values: E6 series (IEC 60063 Norm).

Capacitance tolerances (measured at 1 kHz):

±10% (K); ±20% (M).

tolerance

±5% (J) available upon request

Dissipation factor (DF):

tgδ 10-4 at +25°C ±5°C: ≤15 (8)* at 1kHz * Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C Voltage charge time: 1 min Voltage charge: 100 Vdc

Performance

≥1x10

MΩ (5x105 MΩ )* for C≤0.33µF

≥30000 s (150000 s

)

* for C>0.33µF

* Typical value

Test voltage between terminations (on all pieces):

1500Vac for 1 s + 2200Vdc for 1 s at +25°C

±5°C

TEST METHOD AND PERFORMANCE

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C ± 2°C Relative humidity (RH): 93%

±2%

Test duration: 56 days

Test conditions 2nd

Temperature: +60°C ± 2°C Relative humidity (RH): 95%

±2%

Test duration: 500 hours

Test conditions 3rd

Temperature: +40°C ± 2°C Relative humidity (RH): 93%

±2%

Test duration: 500 hours Voltage value: 230 Vac, 50 Hz

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change | Insulation resistance:

Endurance:

Test conditions

∆C/C|: ≤5%

≥50% of initial limit.

Temperature: +110°C ± 2°C Test duration: 1000 h Voltage applied: 1.25 x V

Performance

+1000Vac 0.1 s/h

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change | Insulation resistance:

Resistance to soldering heat:

Test conditions

∆C/C|: ≤10%

≥50% of initial limit.

Solder bath temperature: +260°C ± 5°C Dipping time (with heat screen):10 s

Performance

± 1 s

Capacitance change |∆C/C|: ≤2%

(d.c.)/1 min

155

09/2008

Page 7

09/2008

156

Rated Cap.

(*)

0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2100 - - S0

0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2150 - - S0

0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2220 - - S0

0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2330 - - S0

0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2470 - - S1

0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2680 - - S0

0.10 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 3100 - - S1

0.10 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3100 - - S0

0.15 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3150 - - S1

0.15 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3150 - - S0

0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3150 - - S3

0.22 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3220 - - S1

0.22 µF 8.5 14.5 18.0 15.0 0.6 400 R46 KI 3220 - - S0

0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3220 - - S2

0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3220 - - S3

0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 KI 3330 - - S1

0.33 µF 8.5 14.5 18.0 15.0 0.8 400 R46 KI 3330 - - S3

0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3330 - - S0

0.33 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3330 - - S2

0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3470 - - S0

0.47 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3470 - - S1

0.56 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3560 - - S0

0.68 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3680 - - S0

0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3220 - - S0

0.33 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3330 - - S1

0.33 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3330 - - S0

0.47 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3470 - - S1

0.47 µF 8.5 17.0 26.5 22.5 0.8 200 R46 KN 3470 - - S0

0.68 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 3680 - - S0

1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4100 - - S2

1.0 µF 11.0 20.0 26.5 22.5 0.8 200 R46 KN 4100 - - S1

1.2 µF 13.0 22.0 26.5 22.5 0.8 200 R46 KN 4120 - - S0

0.47 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3470 - - S0

0.68 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3680 - - S1

1.0 µF 11.0 20.0 32.0 27.5 0.8 150 R46 KR 4100 - - S1

1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46 KR 4150 - - S1

2.2 µF 13.0 25.0 32.0 27.5 0.8 150 R46 KR 4220 - - S2

3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4330 - - S2

4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4470 - - S2

1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4150 - - S1

2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4220 - - S2

2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46 KW 4220 - - S1

3.3 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4330 - - S1

4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4470 - - S2

4.7 µF 19.0 32.0 41.5 37.5 1.0 100 R46 KW 4470 - - S1

6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46 KW 4680 - - S2

10.0 µF 30.0 45.0 41.5 37.5 1.0 100 R46 KW 5100 - - S1

275 Vac / 560 Vdc

Std dimensions

B H L p (V/ µs)

Ø d Max

dv/dt at 390Vdc

Part

Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%)

umber

R.46 SVERSION

X2 CLASS (IEC60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

APPROVALS

ENEC IEC 60384-14

(**)

Approved according to IEC 60384-14

According to IEC 60065

(**) ENEC mark has replaced all the following European

National marks:

Table 1

packaging style

AMMO-PACK AMMO-PACK

REEL

Loose, short leads Loose, long leads Loose, long leads

Loose, insulated rigid leads

Loose, insulated

exible leads

Note: Ammo-pack is the preferred packaging for taped version.

1414 (up to 1µF, 85°C; 250Vac)

CSA

- C22.2 No.1 (up to 1µF, 85°C; 250Vac)

1283

(310 Vac)

- C22.2 No.8

CSA (310 Vac)

GB/T 14472 Class X2

Standard

Ø500mm Ø500mm

Not for use in series with the mains. See www.kemet.com for more information.

No.V4413

No.E97797

File

File No.E85238

File CQC03001008199 CQC03001008842

Pitch (mm)

10.0/15.0

22.5

10.0/15.0

22.5/27.5

Lead

length

(mm)

25 30

150

Class X2 File

Across-the-line File No.E97797

Across-the-line

certied for

Canada

Electromagnetic Interference Filters

Electromagnetic Interference

Filters certied

for Canada

aping style Ordering

Fig.

(mm)

(No.)

12.70

19.0512

12.70

19.0512

-1/+2

±5

(Digit

code

10 to 11)

DQ DQ

CK CK

00 50 40

300Vac Available upon request E12 Series available upon request

All dimensions are in mm

Page 8

Loose Taped

Pitch Box thickness (B) Maximum dimensions (mm) (mm) (mm) B max H max L max

22.5 All B +0.2 H +0.1 L +0.3

27.5 All B +0.2 H +0.1 L +0.3

37.5 All B +0.3 H +0.1 L +0.3

TEST METHOD AND PERFORMANCE

Fig.1 Fig.2

Insulated rigid leads Insulated exible leads 0.5mm

Ø d ±0.05

All dimensions are in mm.

P= 22.5 to 27.5 p = 37.5

0.8 1

GENERAL TECHNICAL DATA

Dielectric: polypropylene lm.

Plates: metal layer deposited by evaporation under vacuum.

Winding: non-inductive type.

tinned wire.

eads:

L Protection: plastic case, thermosetting resin lled.

Box material is solvent resistant and ame retardant according to

UL94 V0.

Marking:

rated voltage, capacitor class, dielectric code, climatic category,

passive ammability category, manufacturing date code, approvals,

manufacturing plant.

Climatic category: 40/110/56 IEC 60068-1

Manufacturer’s logo, series, capacitance, tolerance,

Operating temperature range: -40 to +110°C

Related documents: IEC 60384-14, EN 60384-14.

ELECTRICAL CHARACTERISTICS

Rated voltage (V

300Vac (50/60Hz) / 630 Vdc

Capacitance range: 0.22

): 275Vac (50/60Hz) / 560 Vdc

µF to 10µF

Capacitance values: E6 series (IEC 60063 Norm).

Capacitance tolerances (measured at 1 kHz):

±10% (K); ±20% (M).

Dissipation factor (DF):

tgδ 10-4 at +25°C ±5°C: ≤10 (6)* at 1kHz * Typical value

Insulation resistance:

Test conditions

Temperature: +25°C±5°C Voltage charge time: 1 min Voltage charge: 100 Vdc

Performance

≥1x10

MΩ (5x105 MΩ )* for C≤0.33µF

≥30000 s (150000 s

)

* for C>0.33µF

* Typical value

Test voltage between terminations (on all pieces):

R.46+R

Capacitors with discharge resistor

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

Typical applications: interference suppression and «across-the-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock.

ODUCT CODE: R46

Not for use in series with the mains. See www.kemet.com for more information.

Damp heat, steady state:

Test conditions 1st

Temperature: +40°C ± 2°C Relative humidity (RH): 93% Test duration: 56 days

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change |

∆C/C|: ≤5%

Insulation resistance:

Endurance:

Test conditions

Temperature: +110°C ± 2°C Test duration: 1000 h Voltage applied: 1.25 x V

Performance

Dielectric strength: no dielectric breakdown or

ashover at 4.3 x V

Capacitance change |

∆C/C|: ≤10%

Insulation resistance:

Resistance to soldering heat:

Test conditions

Solder bath temperature: +260°C ± 5°C Dipping time (with heat screen):10 s

Performance

Capacitance change |∆C/C|: ≤2%

APPROVALS

ENEC IEC 60384-14

1283

(310Vac-105°C)

- C22.2 No.8

CSA (310Vac-105°C)

Approved according to IEC 60384-14 According to IEC 60065.

Class X2 File

Electromagnetic Interference Filters

Electromagnetic Interference

Filters certied

for Canada

±2%

(d.c.)/1 min

≥50% of initial limit.

+1000Vac 0.1 s/h

(d.c.)/1 min

≥50% of initial limit.

± 1 s

No.V4413

No.E85238

File

No.E85238

File

157

09/2008

Page 9

09/2008

158

R.46+R

Capacitors with discharge resistor

X2 CLASS (IEC 60384-14) - MKP Series

METALLIZED POLYPROPYLENE FILM CAPACITOR

SELF-HEALING PROPERTIES

PRODUCT CODE: R46

Not for use in series with the mains. See www.kemet.com for more information.

Rated

Cap. (*)

0.22 µ

0.33 µF 8.5 17.0 26.5 22.5 0.8 200 R46KN 3330 - - 01

0.47 µF 10.0 18.5 26.5 22.5 0.8 200 R46KN 3470 - - 01

0.68 µF 11.0 20.0 26.5 22.5 0.8 200 R46KN 3680 - - 01

0.47 µF 11.0 20.0 32.0 27.5 0.8 150 R46KR 3470 - - 01

0.68 µF 11.0 20.0 32.0 27.5 0.8 150 R46KR 3680 - - M1

1.0 µF 13.0 22.0 32.0 27.5 0.8 150 R46KR 4100 - - M1

1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46KR 4150 - - M1

2.2 µF 14.0 28.0 32.0 27.5 0.8 150 R46KR 4220 - - M1

3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R46KR 4330 - - M2

4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R46KR 4470 - - M1

1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46KW 4150 - - M1

2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46KW 4220 - - M1 - x

3.3

4.7

6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46KW 4680 - - M2

10.0 µF 24.0 44.0 41.5 37.5 1.0 100 R46KW 5100 - - M1

275 Vac / 560 Vdc

Std dimensions

B H L p

F 7.0 16.0 26.5 22.5 0.8 200 R46KN 3220 - - 01

µF 16.0 28.5 41.5 37.5 1.0 100 R46KW 4330 - - M1 - x

µF 19.0 32.0 41.5 37.5 1.0 100 R46KW 4470 - - M1

Ø d

Max dv/dt at 390Vdc

(V/ µs)

Part

umber

Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%) Value of discharge resistor (Table 2)

Rated

Cap. (*)

0.22 µ

0.33 µF 8.5 17.0 26.5 22.5 0.8 200 R463N 3330 - - 01

0.47 µF 10.0 18.5 26.5 22.5 0.8 200 R463N 3470 - - 01

0.68 µF 11.0 20.0 26.5 22.5 0.8 200 R463N 3680 - - 01

0.47 µF 11.0 20.0 32.0 27.5 0.8 150 R463R 3470 - - 01

0.68 µF 11.0 20.0 32.0 27.5 0.8 150 R463R 3680 - - M1

1.0 µF 13.0 22.0 32.0 27.5 0.8 150 R463R 4100 - - M1

1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R463R 4150 - - M1

2.2 µF 14.0 28.0 32.0 27.5 0.8 150 R463R 4220 - - M1

3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R463R 4330 - - M2

4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R463R 4470 - - M1

1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R463W 4150 - - M1

2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R463W 4220 - - M1 - x

3.3

4.7

6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R463W 4680 - - M2

10.0 µF 24.0 44.0 41.5 37.5 1.0 100 R463W 5100 - - M1

300 Vac / 630 Vdc

Std dimensions

B H L p

F 7.0 16.0 26.5 22.5 0.8 200 R463N 3220 - - 01

µF 16.0 28.5 41.5 37.5 1.0 100 R463W 4330 - - M1 - x

µF 19.0 32.0 41.5 37.5 1.0 100 R463W 4470 - - M1

Ø d

Max dv/dt at 390Vdc

(V/ µs)

Part

umber

Rated voltage (3=300Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%) Value of discharge resistor (Table 2)

Table 1

Standard

packaging style

- x

Ø500mm

REEL

Loose, short leads Loose, long leads Loose, long leads

Loose, insulated rigid leads

Loose, insulated

exible leads

PRODUCT CODE SYSTEM

The part number, comprising 15 digits, is formed as follows:

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Lead

length

(mm)

25 30

150

-1/+2

±5

aping style Ordering

Fig.

(mm)

(No.)

19.05 2 22.5/27.5 CK

Pitch

(mm)

R 4 6

- x

Digit 1 to 3 Series code.

- x

Digit 4 a.c. rated voltage:

- x

K = 275Vac; 3 = 300Vac Digit 5 Pitch: N = 22.5; R = 27.5; W = 37.5 mm

Digit 6 to 9 Digits 7 - 8 - 9 indicate the rst three digits of

Capacitance value and the 6th digit indicates the number of zeros that must be added to obtain the Rated Capacitance in pF. Digit 10 to 11 Mechanical version and/or packaging (table 1)

Digit 12 Identies the dimensions and electrical

- x

characteristics.

- x

Digit 13 Internal use

- x

Digit 14 Capacitance tolerance:

- x

Digit 15 Value of the discharge resistor (tolerance

- x

according to the following table*:

- x

Table 2

- x

R code (x)

470 kΩ E

680 kΩ F

1 MΩ G

1.2 MΩ L

1.5 MΩ N

2.2 MΩ P

3.3 MΩ Q

- x

4.7 MΩ S

- x

6.8 MΩ T

- x

10 MΩ V

All dimensions are in mm

±10%; M=±20%

*Other resistors are avaible upon request.

code

(Digit 10 to 1

00 50 40

- -

±10%)

Datasheet R46KR410000M1M, R46KN322000M1M, R46KI322000M2M, R46 series Specification

Specifications and Main Features

Frequently Asked Questions

User Manual