MIPS
PR31100
Highly integrated embedded processor
Preliminary specification 1996 Aug 07
INTEGRATED CIRCUITS
Version 1.2
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
Version 1.2
2
1996 Aug 07
GENERAL DESCRIPTION
PR31100 Processor is a single-chip, low-cost, integrated embedded
processor consisting of MIPS R3000 core and system support logic
to interface with various types of devices.
PR31100 consists of a MIPS R3000 RISC CPU with 4 KBytes of
instruction cache memory and 1 KByte of data cache memory, plus
integrated functions for interfacing to numerous system components
and external I/O modules. The R3000 RISC CPU is also augmented
with a multiply/accumulate module to allow integrated DSP
functions, such as a software modem for high-performance standard
data and fax protocols. PR31100 also contains multiple DMA
channels and a high-performance and flexible Bus Interface Unit
(BIU) for providing an efficient means for transferring data between
external system memory, cache memory, the CPU core, and
external I/O modules. The types of external memory devices
supported include dynamic random access memory (DRAM),
synchronous dynamic random access memory (SDRAM), static
random access memory (SRAM), Flash memory, read-only memory
(ROM), and expansion cards (PCMCIA and/or MagicCard).
PR31100 also contains a System Interface Module (SIM) containing
integrated functions for interfacing to numerous external I/O
modules such as liquid crystal displays (LCDs), the UCB1100 (which
handles most of the analog functions of the system, including sound
and telecom codecs and touchscreen ADC), ISDN/high-speed
serial, infrared, wireless peripherals, Magicbus, etc. Lastly, PR31100
contains support for implementation of power management,
whereby various PR31100 internal modules and external
subsystems can be individually (under software control) powered up
and down.
Figure 1 shows an External Block Diagram of PR31100.
FEATURES
•32-bit R3000 RISC static CMOS CPU
•4 KByte instruction cache
•1 KByte data cache
•Multiply/accumulator
•On-chip peripherals with individual power-down
– Multi-channel DMA controller
– Bus interface unit
– Memory controller for ROM, Flash, RAM, DRAM, SDRAM,
SRAM, and PCMCIA and/or MagicCard
– Power management module
– Video module
– Real-time clock 32.760KHz reference
– High-speed serial interface
– Infrared module
– Dual-UART
– SPI bus
•3.3V supply voltage
•208-pin LQFP (Low profile quad flat pack)
•40MHz operation frequency
ORDERING INFORMATION
PART NUMBER TEMPERATURE RANGE (°C) AND PACKAGE
FREQUENCY
(MHz)
DRAWING NUMBER
PR31100ABC 0 to +70, 208-pin Low Profile Quad Flat Pack 40 LQFP208
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
3
R3000 RISC
CPU Core
ICache
4KByte
DCache
1KByte
Bus Interface Unit (BIU) Module
(S)DRAM/PCMCIA/ROM
Data
Addr
Magicbus Module
CHI Module
Addr
Data
Data
Addr
Control
to UCB1100
to LCD
to Magicbus
to high
speed serial
to IR
Timer Module
(+ RTC)
IR Module
UART Module
(dual UART)
MAC
to UART
Power Module
SPI Module
to Power
Supply
IO Moduleto general
purpose I/O
32 KHz
SYSCLK Clock Module
Interrupt Module
System Interface Module (SIM)
to
Memory
CPU
Module
DATA
TAG
ADDR
System Interface Unit (SIU) Module
Arbitration/DMA/AddrDecode
Video Module
SIB Module
Figure 1. PR31100 Block Diagram
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
4
OVERVIEW
Each of the on-chip peripherals consist of:
BIU Module
•System memory and PR31100 Bus Interface Unit (BIU)
– supports up to 2 banks of physical memory
– supports self–refreshing DRAM and SDRAM
– programmable parameters for each bank of DRAM or SDRAM
(row/column address configuration, refresh, burst modes, etc.)
•programmable chip select memory access
– 4 programmable (size, wait states, burst mode control) memory
device and general purpose chip selects
available for system ROM, SRAM, Flash
available for external port expansion registers
– 4 programmable (wait states, burst mode control) MagicCard or
general purpose chip selects
available for (future) MagicCard expansion memory
PR31100 provides the chip select and card detect signals
supports card insertion/removal timeouts
MagicCard requires minimal number of unique control/status
signals per port
•supports up to 2 identical full PCMCIA ports
– PR31100 and UCB1100 provide the control signals and accepts
the status signals which conform to the PCMCIA version 2.01
standard
– appropriate connector keying and level–shifting buffers required
for 3.3V versus 5V PCMCIA interface implementations
SIU Module
•multi–channel 32–bit DMA controller and System Interface Unit
(SIU)
•independent DMA channels for video, Magicbus, SIB to/from
UCB1100 audio/telecom codecs, high–speed serial port, IR UAR T,
and general purpose UART
•address decoding for submodules within System Interface Module
(SIM)
CPU Module
•R3000 RISC central processing unit core
– full 32–bit operation (registers, instructions, addresses)
– 32 general purpose 32–bit registers; 32–bit program counter
– MIPS RISC Instruction Set Architecture (ISA) supported
•on–chip cache
– 4 KByte direct–mapped instruction cache (I–cache)
physical address tag and valid bit per cache line
programmable burst size
instruction streaming mode supported
– 1 KByte data cache (D–cache)
physical address tag and valid bit per cache line
programmable burst size
write–through
– cache address snoop mode supported for DMA
– 4–level deep write buffer
•programmable memory protection
– separate read and write protection control for kernel and user
space
– 8 total protectable regions available, each individually
programmable, using breakpoint address, mask, control, and
status registers
– causes address exception on illegal reads or writes
•high–speed multiplier/accumulator
– on–chip hardware multiplier
– supports 16x16 or 32x32 multiplier operations, with 64–bit
accumulator
– existing multiply instructions are enhanced and new multiply
and add instructions are added to R3000 instruction set to
improve the performance of DSP applications
•CPU interface
– handles data bus, address bus, and control interface between
CPU core and rest of PR31100 logic
Clock Module
•PR31100 supports system–wide single crystal configuration,
besides the 32 KHz RTC XTAL (reduces cost, power, and board
space)
•common crystal rate divided to generate clock for CPU, video,
sound, telecom, UARTs, etc.
•external system crystal rate is vendor–dependent
•independent enabling or disabling of individual clocks under
software control, for power management
CHI Module
•high–speed serial Concentration Highway Interface (CHI) contains
logic for interfacing to external full–duplex serial
time–division–multiplexed (TDM) communication peripherals
•supports ISDN line interface chips and other PCM/TDM serial
devices
•CHI interface is programmable (number of channels, frame rate,
bit rate, etc.) to provide support for a variety of formats
•supports data rates up to 4.096 Mbps
•independent DMA support for CHI receive and transmit
Interrupt Module
•contains logic for individually enabling, reading, and clearing all
PR31100 interrupt sources
•interrupts generated from internal PR31100 modules or from edge
transitions on external signal pins
IO Module
•contains support for reading and writing the 7 bi–directional
general purpose IO pins and the 32 bi–directional multi–function
IO pins
•each IO port can generate a separate positive and negative edge
interrupt
•independently configurable IO ports allow PR31100 to support a
flexible and wide range of system applications and configurations
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
5
IR Module
•IR consumer mode
– allows control of consumer electronic devices such as stereos,
TVs, VCRs, etc.
– programmable pulse parameters
– external analog LED circuitry
•IRDA communication mode
– allows communication with other IRDA devices such as FAX
machines, copiers, printers, etc.
– supported by UART module within PR31100
– external analog receiver preamp and LED circuitry
– data rate = up to 115 Kbps at 1 meter
•IR FSK communication mode
– supported by UART module within PR31100
– external analog IR chip(s) perform frequency modulation to
generate the desired IR communication mode protocol
– data rate = up to 36000 bps at 3 meters
•carrier detect state machine
– periodically enables IR receiver to check if a valid carrier is
present
Magicbus Module
•synchronous, serial 2–wire (clock and data), half–duplex
communications protocol
•supports low–cost, low–power peripherals
•supports maximum data rate of 14.75 Mbps
•DMA support for Magicbus receive and transmit
Power Module
•power–down modes for individual internal peripheral modules
•serial (SPI port) power supply control interface supported
•power management state machine has 4 states: RUNNING,
DOZING, SLEEP, and COMA
Serial Interconnect Bus (SIB) Module
•PR31100 contains holding and shift registers to support the serial
interface to the UCB1100 and/or other optional codec devices
•interface compatible with slave mode 3 of Crystal CS4216 codec
•synchronous, frame–based protocol
•PR31100 always master source of clock and frame frequency and
phase; programmable clock frequency
•each SIB frame consists of 128 clock cycles, further divided into 2
subframes or words of 64 bits each (supports up to 2 devices
simultaneously)
•independent DMA support for audio receive and transmit, telecom
receive and transmit
•supports 8–bit or 16–bit mono telecom formats
•supports 8–bit or 16–bit mono or stereo audio formats
•independently programmable audio and telecom sample rates
•CPU read/write registers for subframe control and status
System Peripheral Interface (SPI) Module
•provides interface to SPI peripherals and devices
•full–duplex, synchronous serial data transfers (data in, data out,
and clock signals)
•PR31100 supplies dedicated chip select and interrupt for an SPI
interface serial power supply
•8–bit or 16–bit data word lengths for the SPI interface
•programmable SPI baud rate
Timer Module
•Real Time Clock (RTC) and Timer
•40–bit counter (30.517 µsec granularity);
maximum uninterrupted time = 388.36 days
•40–bit alarm register (30.517 µsec granularity)
•16–bit periodic timer (0.868 µsec granularity);
maximum timeout = 56.8 msec
•interrupts on alarm, timer, and prior to RTC roll–over
UART Module
•2 independent full–duplex UARTs
•programmable baud rate generator
•UART–A port used for serial control interface to external IR
module
•UART–B port used for general purpose serial control interface
•UART–A and UART–B DMA support for receive and transmit
Video Module
•bit–mapped graphics
•supports monochrome, grey scale, or color modes
•time–based dithering algorithm for grey scale and color modes
•supports multiple screen sizes
•supports split and non–split displays
•variable size and relocatable video buffer
•DMA support for fetching image data from video buffer
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
6
Figure 2 shows a typical system block diagram cosisting of
PR31100 and UCB1100 for a total system solution.
R3000
RISC
CPU
core
I–Cache/RAM
D–Cache/
RAM
32–bit Bus
LCD Interface
Timers
Real–time Clock
Serial I/F and
Magicbus
1–2 PCMCIA Slots
UCB1100
Power Supply
MagicBus
Jack
Main
Backup
(Lithium)
DAA
RF
Xceiver
or
Touchscreen
(Resistive)
Phone Jack
IR
PR31100
AC
Adapter
3.3V
Memory Protection
PCMCIA/ROM I/F
1–64 MBytes
ROM
1–16 MBytes
(S)DRAM
TThermistor
3.3V
32 KHz
SYSCLK
ID ROM
High speed serial port
ISDN
or other
peripherals
LCD
DRAM/SDRAM Interface
Figure 2. System Block Diagram
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
7
PIN CONFIGURATION
208
1
52
53 104
105
156
157
208-PIN
PLASTIC
QUAD FLAT PACK
TOP VIEW
Pin Function
1 V
DD
2 D(0)
3 V
SS
4 D(1)
5 D(2)
6 V
DD
7 D(3)
8 V
SS
9 D(4)
10 V
DD
11 D(5)
12 D(6)
13 V
SS
14 D(7)
15 V
SS
16 D(8)
17 V
DD
18 D(9)
19 D(10)
20 V
SS
21 D(11)
22 V
DD
23 D(12)
24 D(13)
25 V
SS
26 D(14)
27 D(15)
28 V
DD
29
30 MFIO(1)
31 MBUSINT
32 MBUSDATA
33 V
SS
34 MBUSCLK
35 V
DD
36 V
DD
37 SIBMCLK
38 V
SS
39 SIBSCLK
40 SIBSYNC
41 SIBDIN
42 SIBDOUT
43 V
DD
44 SIBIRQ
45 MFIO(0)
46 IO(6)
47 IO(50
48 V
SS
49 chiclk
50 chifs
51 chidin
52 chidout
Pin Function
53 V
DD
54 RXD
55 TXD
56 IO(4)
57
58 IRIN
59 IROUT
60 V
SS
61 V
DD
62 CARDET
63 TXPWR
64 IO(3)
65 IO(2)
66 V
SS
67 SPICLK
68 SPIIN
69 SPIOUT
70 V
DD
71 TESTCPU
72 TESTIN
73 TESTOUT
74 TESTSIU
75 V
SS
76 VCC3
77 BC32K
78 V
DD
79 C32KIN
80 C32KOUT
81 V
SS
82 PWRCS
83 PWRINT
84 PWROK
85
86 ONBUTN
87 /PON
88 /CPURES
89 V
DD
90 DISPON
91 FRAME
92 V
SS
93 DF
94 LOAD
95 CP
96 V
SS
97 V
DD
98 VDAT(0)
99 VDAT(1)
100 VDAT(2)
101 VDAT(3)
102 V
SS
103 IO(1)
104 V
DD
Pin Function
105 /CARD2WAIT
106 /CARD2CSH
107 /CARD2CSL
108 IO(0)
109 V
SS
110 /IORD
111 /IOWR
112 /CARDREG
113 /CARD1WAIT
114 V
DD
115 MFIO(2)
116 V
DD
117 /CARD1CSL
118 /CARD1CSH
119 V
SS
120 /MCS3
121 /MCS2
122 /MCS1
123 /MCS0
124 /CS3
125 /CS2
126 /CS1
127 V
DD
128 SYSCLKIN
129 SYSCLKOUT
130 V
SS
131 V
SS
132 V
DD
133 D(31)
134 D(30)
135 V
SS
136 D(29)
137 V
DD
138 D(28)
139 D(27)
140 V
SS
141 D(26)
142 V
SS
143 D(250
144 V
DD
145 D(24)
146 D(23)
147 V
DD
148 D(22)
149 V
SS
150 D(21)
151 V
DD
152 D(20)
153 D(19)
154 V
SS
155 D(18)
156 V
DD
Pin Function
157 D(17)
158 V
SS
159 D(16)
160 V
DD
161
162 /CS0
163 /RD
164 V
SS
165 V
DD
166 /DGRNT
167 /DREQ
168 ALE
169 /WE
170 V
DD
171 A(12)
172 A(11)
173 V
SS
174 A(10)
175 A(9)
176 V
DD
177 A(8)
178 A(7)
179 V
SS
180 A(6)
181 A(5)
182 V
DD
183 A(4)
184 V
SS
185 A(3)
186 A(2)
187 V
DD
188 A(1)
189 A(0)
190 V
SS
191 V
SS
192 /DCS0
193 /RAS1
194 /RAS0
195 /CAS3
196 V
DD
197 /CAS2
198 /CAS1
199 /CAS0
200 V
SS
201 V
DD
202 DCKE
203 V
SS
204 DCLKIN
205 DCLKOUT
206 V
DD
207 DQMH
208 DQML
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
8
PIN DESCRIPTIONS
Overview
The PR31100 processor contains 208 pins consisting of input, output, bi–directional, and power and ground pins. These pins are used to
support various functions. The following sections will describe the function of each pin including any special power–down considerations for
each pin.
Pins
The PR31100 PROCESSOR contains 208 total pins, consisting of 136 signal pins, 4 spare pins, 34 power pins, and 34 ground pins. Of the 136
signal pins, 32 of them are multi–function and can be independently programmed either as IO ports or for an alternate standard/normal function.
As an IO port, any of these pins can be programmed as an input or output port, with the capability of generating a separate positive and
negative edge interrupt. See Section 2.3 for a summary of the multi–function IO ports versus their standard functions.
PIN #
NAME TYPE NAME AND FUNCTION
Memory Pins
D(31:0) I/O These pins are the data bus for the system. 8–bit SDRAMs should be connected to bits 7:0 and
16–bit SDRAMs and DRAMs should be connected to bits 15:0. All other 16–bit ports should be
connected to bits 31:16. Of course, 32–bit ports should be connected to bits 31:0. These pins are
normally outputs and only become inputs during reads, thus no resistors are required since the
bus will only float for a short period of time during bus turn–around.
A(12:0) O These pins are the address bus for the system. The address lines are multiplexed and can be
connected directly to SDRAM and DRAM devices. To generate the full 26–bit address for static
devices, an external latch must be used to latch the signals using the ALE signal. For static
devices, address bits 25:13 are provided by the external latch and address bits 12:0 (directly
connected from PR31100’s address bus) are held afterward by PR31100 processor for the
remainder of the address bus cycle.
168 ALE O This pin is used as the address latch enable to latch A(12:0) using an external latch, for generating
the upper address bits 25:13.
163 /RD O This pin is used as the read signal for static devices. This signal is asserted for reads from
/MCS3–0, /CS3–0, /CARD2CS and /CARD1CS for memory and attribute space, and for reads
from PR31100 processor accesses if SHOWPR31100 is enabled (for debugging purposes).
169 /WE O This pin is used as the write signal for the system. This signal is asserted for writes to /MCS3–0,
/CS3–0, /CARD2CS and /CARD1CS for memory and attribute space, and for writes to DRAM and
SDRAM.
199 /CAS0 (/WE0) O This pin is used as the CAS signal for SDRAMs, the CAS signal for D(7:0) for DRAMs, and the
write enable signal for D(7:0) for static devices.
198 /CAS1 (/WE1) O This pin is used as the CAS signal for D(15:8) for DRAMs and the write enable signal for D(15:8)
for static devices.
197 /CAS2 (/WE2) O This pin is used as the CAS signal for D(23:16) for DRAMs and the write enable signal for
D(23:16) for static devices.
195 /CAS3 (/WE3) O This pin is used as the CAS signal for D(31:24) for DRAMs and the write enable signal for
D(31:24) for static devices.
194 /RAS0 O This pin is used as the RAS signal for SDRAMs and the RAS signal for Bank0 DRAMs.
193 /RAS1 (/DCS1) O This pin is used as the chip select signal for Bank1 SDRAMs and the RAS signal for Bank1
DRAMs.
192 /DCS0 O This pin is used as the chip select signal for Bank0 SDRAMs.
202 DCKE O This pin is used as the clock enable for SDRAMs.
204 DCLKIN I This pin must be tied externally to the DCLKOUT signal and is used to match skew for the data
input when reading from SDRAM and DRAM devices.
205 DCLKOUT O This pin is the (nominal) 73.728 MHz clock for the SDRAMs.
207 DQMH O This pin is the upper data mask for a 16–bit SDRAM configuration.
208 DQML O This pin is the lower data mask for a 16–bit SDRAM or 8–bit SDRAM configuration.
124–126,
162
/CS3–0 O These pins are the Chip Select 3 through 0 signals. They can be configured to support either
32–bit or 16–bit ports.
120–123 /MCS3–0 O These pins are the MagicCard Chip Select 3 through 0 signals. They only support 16–bit ports.
106, 107 /CARD2CSH,L O These pins are the Chip Select signals for PCMCIA card slot 2.
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
9
PIN # NAME AND FUNCTIONTYPENAME
Memory Pins (continued)
117, 118 /CARD1CSH,L O These pins are the Chip Select signals for PCMCIA card slot 1.
112 /CARDREG O This pin is the /REG signal for the PCMCIA cards.
110 /CARDIORD O This pin is the /IORD signal for the PCMCIA IO cards.
111 /CARDIOWR O This pin is the /IOWR signal for the PCMCIA IO cards.
115 /CARDDIR O This pin is used to provide the direction control for bi–directional data buffers used for the PCMCIA
slot(s). This signal will assert whenever /CARD2CSH or /CARD2CSL or /CARD1CSH or
/CARD1CSL is asserted and a read transaction is taking place.
105 /CARD2WAIT I This pin is the card wait signal from PCMCIA card slot 2.
113 /CARD1WAIT I This pin is the card wait signal from PCMCIA card slot 1.
Bus Arbitration Pins
167 /DREQ I This pin is used to request external arbitration. If the TESTSIU signal is high and the TESTSIU
function has been enabled, then once /DGRNT is asserted, external logic can initiate reads or
writes to PR31100 processor registers by driving the appropriate input signals. If the TESTSIU
signal is low or the TESTSIU function has not been enabled, then PR31100 memory transactions
are halted and certain memory signals will be tri–stated when /DGRNT is asserted in order to allow
an external master to access memory.
166 /DGRNT O This pin is asserted in response to /DREQ to inform the external test logic or bus master that it can
now begin to drive signals.
Clock Pins
128 SYSCLKIN I This pin should be connected along with SYSCLKOUT to an external crystal which is the main
PR31100 clock source.
129 SYSCLKOUT O This pin should be connected along with SYSCLKIN to an external crystal which is the main
PR31100 clock source.
79 C32KIN I This pin along with C32KOUT should be connected to a 32.768 KHz crystal.
80 C32KOUT O This pin along with C32KIN should be connected to a 32.768 KHz crystal.
77 BC32K O This pin is a buffered output of the 32.768 KHz clock.
CHI Pins
50 CHIFS I/O This pin is the CHI frame synchronization signal. This pin is available for use in one of two modes.
As an output, this pin allows PR31100 to be the master CHI sync source. As an input, this pin
allows an external peripheral to be the master CHI sync source and the PR31100 CHI module will
slave to this external sync.
49 CHICLK I/O This pin is the CHI clock signal. This pin is available for use in one of two modes. As an output,
this pin allows PR31100 to be the master CHI clock source. As an input, this pin allows an
external peripheral to be the master CHI clock source and the PR31100 CHI module will slave to
this external clock.
52 CHIDOUT O This pin is the CHI serial data output signal.
51 CHIDIN I This pin is the CHI serial data input signal.
IO Pins
46, 107,
47, 108,
56, 64,
64
IO(6:0) I/O These pins are general purpose input/output ports. Each port can be independently programmed
as an input or output port. Each port can generate a separate positive and negative edge interrupt.
Each port can also be independently programmed to use a 16 to 24 msec debouncer.
30, 45 MFIO(1:0) I/O These pins are multi–function input/output ports. Each port can be independently programmed as
an input or output port, or can be programmed for multi–function use to support vendor–dependent
test signals (for debugging purposes only). Each port can generate a separate positive and
negative edge interrupt. Note that 30 other multi–function pins are available for usage as
multi–function input/output ports. These pins are named after their respective standard/normal
function and are not listed here.
Magicbus Pins
34 MBUSCLK I/O This pin is the bi–directional Magicbus clock signal. MBUSCLK is an input signal whenever
PR31100 is in the slave mode and is an output signal whenever PR31100 is in the master mode.
32 MBUSDATA I/O This pin is the bi–directional Magicbus data signal. MBUSDATA is an input signal whenever
PR31100 is in the slave mode and is an output signal whenever PR31100 is in the master mode.
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
10
PIN # NAME AND FUNCTIONTYPENAME
31 MBUSINT I This pin is the Magicbus interrupt signal. This signal is used to interrupt PR31100 whenever a
peripheral has been attached to or detached from the bus, or whenever a peripheral has initiated
an interrupt event.
Reset Pins
88 /CPURES I This pin is used to reset the CPU core. This pin should be connected to a switch for initiating a
reset in the event that a software problem might hang the CPU core. The pin should also be pulled
up to VSTANDBY through an external pull–up resistor.
87 /PON I This pin serves as the Power On Reset signal for PR31100. This signal must remain low when
VSTANDBY is asserted until VSTANDBY is stable. Once VSTANDBY is asserted, this signal
should never go low unless all power is lost in the system.
Power Supply Pins
86 ONBUTN I This pin is used as the On Button for the system. Asserting this signal will cause PWRCS to set to
indicate to the System Power Supply to turn power on to the system. PWRCS will not assert if the
PWROK signal is low.
82 PWRCS O This pin is used as the chip select for the System Power Supply. When the system is off, the
assertion of this signal will cause the System Power Supply to turn VCCDRAM and VCC3 on to
power up the system. The Power Supply will latch SPI commands on the falling edge of PWRCS.
Power Supply Pins (continued)
84 PWROK I This pin provides a status from the System Power Supply that there is a good source of power in
the system. This signal typically will be asserted if there is a Battery Charger supplying current or
if the Main Battery is good and the Battery Door is closed. If PWROK is low when the system is
powered off, PWRCS will not assert as a result of the user pressing the ONBUTN or an interrupt
attempting to wake up the system. If the device is on when the PWROK signal goes low, the
software will immediately shut down the system since power is about to be lost. When PWROK
goes low, there must be ample warning so that the software can shut down the system before
power is actually lost.
83 PWRINT I This pin is used by the System Power Supply to alert the software that some status has changed
in the System Power Supply and the software should read the status from the System Power
Supply to find out what has changed. These will be low priority events, unlike the PWROK status,
which is a high priority emergency case.
76 VCC3 I This pin provides the status of the power supply for the ROM, UCB1100, system buffers, and other
transient components in the system. This signal will be asserted by the System Power Supply
when PWRCS is asserted, and will always be turned off when the system is powered down.
SIB Pins
41 SIBDIN I This pin contains the input data shifted from UCB1100 and/or external codec device.
42 SIBDOUT O This pin contains the output data shifted to UCB1100 and/or external codec device.
39 SIBSCLK O This pin is the serial clock sent to UCB1100 and/or external codec device. The programmable
SIBSCLK rate is derived by dividing down from SIBMCLK.
40 SIBSYNC O This pin is the frame synchronization signal sent to UCB1100 and/or external codec device. This
frame sync is asserted for one clock cycle immediately before each frame starts and all devices
connected to the SIB monitor SIBSYNC to determine when they should transmit or receive data.
44 SIBIRQ I This pin is a general purpose input port used for the SIB interrupt source from UCB1100. This
interrupt source can be configured to generate an interrupt on either a positive and/or negative
edge.
37 SIBMCLK I/O This pin is the master clock source for the SIB logic. This pin is available for use in one of two
modes. First, SIBMCLK can be configured as a high–rate output master clock source required by
certain external codec devices. In this mode all SIB clocks are synchronously slaved to the main
PR31100 system clock CLK2X. Conversely, SIBMCLK can be configured as an input slave clock
source. In this mode, all SIB clocks are derived from an external SIBMCLK oscillator source,
which is asynchronous with respect to CLK2X. Also, for this mode, SIBMCLK can still be
optionally used as a high–rate master clock source required by certain external codec devices.
SPI Pins
67 SPICLK O This pin is used to clock data in and out of the SPI slave device.
69 SPIOUT O This pin contains the data that is shifted into the SPI slave device.
68 SPIIN I This pin contains the data that is shifted out of the SPI slave device.
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
11
PIN # NAME AND FUNCTIONTYPENAME
UART and IR Pins
55 TXD O This pin is the UART transmit signal from the UARTA module.
54 RXD I This pin is the UART receive signal to the UARTA module.
59 IROUT O This pin is the UART transmit signal from the UARTB module or the Consumer IR output signal if
Consumer IR mode is enabled.
58 IRIN I This pin is the UART receive signal to the UARTB module.
RXPWR O This pin is the receiver power output control signal to the external communication IR analog
circuitry.
62 CARDET I This pin is the carrier detect input signal from the external communication IR analog circuitry.
Video Pins
91 FRAME O This pin is the frame synchronization pulse signal between the Video Module and the LCD, and is
used by the LCD to return it’s pointers to the top of the display. The Video Module asserts FRAME
after all the lines of the LCD have been shifted and transferred, producing a full frame of display.
93 DF O This pin is the AC signal for the LCD. Since LCD plasma tends to deteriorate whenever subjected
to a DC voltage, the DF signal is used by the LCD to alternate the polarity of the row and column
voltages used to turn the pixels on and off. The DF signal can be configured to toggle on every
frame or can be configured to toggle every programmable number of LOAD signals.
94 LOAD O This pin is the line synchronization pulse signal between the Video Module and the LCD, and is
used by the LCD to transfer the contents of it’s horizontal line shift register to the LCD panel for
display. The Video Module asserts LOAD after an entire horizontal line of data has been shifted
into the LCD.
95 CP O This pin is the clock signal for the LCD. Data is pushed by the Video Module on the rising edge of
CP and sampled by the LCD on the falling edge of CP.
101, 100,
99, 98
VDAT(3:0) O These pins are the data for the LCD. These signals are directly connected to the LCD for 4–bit
non–split displays. For 4–bit split and 8–bit non–split displays, an external register is required to
demultiplex the 4–bit data into the desired 8 parallel data lines needed for the LCD.
90 DISPON O This pin is the display–on enable signal for the LCD.
Test Pins
74 TESTSIU I This pin allows external logic to initiate read or write transactions to PR31100 registers. The
TESTSIU mode is enabled by toggling this signal after the device has powered up. Once the
function is enabled, if the TESTSIU pin is high when the bus is arbitrated (using /DREQ and
/DGRNT), then external logic can initiate read and write transactions to PR31100 registers. This
pin is used for debugging purposes only.
71 TESTCPU I This pin allows numerous internal CPU core signals to be brought to external PR31100 pins, in
place of the normal signals assigned to these pins. The CPU core signals assigned to their
respective pins during TESTCPU mode are vendor–dependent. The TESTCPU mode is enabled
by asserting this TESTCPU signal, and this function is provided for generating test vectors for the
CPU core. This pin is used for debugging purposes only.
72 TESTIN I This pin is reserved for vendor–dependent use. This pin is used for debugging purposes only.
73 TESTOUT O This pin is reserved for vendor–dependent use. This pin is used for debugging purposes only.
Spare Pins
NC4–1 No
Connect
These pins are reserved for future use and should be left unconnected.
Power Supply Pins
VDD (34 each) +3.3V These pins are the power pins for PR31100 and should be connected to the digital +3.3V power
supply VSTANDBY.
VSS (34 each) GND These pins are the ground pins for PR31100 and should be connected to digital ground. NOTE:
For some vendor–dependent implementations of PR31100, pin 131 may be used for a filter
capacitor for the SYSCLK oscillator (capacitor connected between pin 131 and digital ground).
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
12
ELECTRICAL CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS
VSS = 0V
SYMBOL
PARAMETER LIMITS UNIT
V
DD
Power supply voltage VSS – 0.5 to 4.5 V
V
IN
Input voltage VSS – 0.5 to VDD + 0.5 V
T
stg
Storage temperature range –55 to +125 °C
Pd Maximum dissipation (T
amb
= 70°C) 1 W
RECOMMENDED OPERATING CONDITION
VSS = 0V
LIMITS
SYMBOL
PARAMETER
MIN TYP MAX
UNIT
V
DD
Power supply voltage 3.0 3.3 3.6 V
V
IN
Input voltage V
SS
– V
DD
V
T
opr
Operating temperature range 0 – 70 °C
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V.
LIMITS
SYMBOL
PARAMETER
CONDITIONS
MIN TYP MAX
UNIT
I
DD
Operating current
VIN = VDD or VSS; VDD = MAX
IOH = IOL = 0
– 110 TBD mA
I
DDS
Static current
VIN = VDD or VSS; VDD = MAX
I
OH
= IOL = 0
– 50 100 µA
I
L
Input leakage current
VDD = MAX; VIH = V
DD
VIL = V
SS
–10 – 10 µA
V
IH1
High level input voltage
1
VDD = 3.6V VDD × 0.8 – VDD + 0.3 V
V
IL1
Low level input voltage
1
VDD = 3.0V –0.3 – VDD × 0.2 V
V
IH2
High level input voltage
2
VDD = 3.6V 2.4 – VDD + 0.3 V
V
IL2
Low level input voltage
2
VDD = 3.0V –0.3 – 0.6 V
V
OH1
High level output voltage
3
VDD = 3.0; IOH = –4mA VDD – 0.6 – – V
V
OL1
Low level output voltage
3
VDD = 3.0; IOL = 4mA – – VSS + 0.4 V
V
OH2
High level output voltage
4
VDD = 3.0; IOH = –8mA VDD – 0.6 – – V
V
OL2
Low level output voltage
4
VDD = 3.0; IOL = 8mA – – VSS + 0.4 V
V
OH3
High level output voltage
5
VDD = 3.0; IOH = –16mA VDD – 0.6 – – V
V
OL3
Low level output voltage
5
VDD = 3.0; IOL = 16mA – – VSS + 0.4 V
V
OH4
High level output voltage
6
VDD = 3.0; IOH = –24mA VDD – 0.6 – – V
V
OL4
Low level output voltage
6
VDD = 3.0; IOL = 24mA – – VSS + 0.4 V
I
OZ
Off-state leakage current
VDD = MAX; VOH = V
DD;
V
OL
= V
SS
TBD – TBD µA
NOTES:
1. SYSVLKIN
2. Other inputs
3. D[31:0], /RAS0, /RAS1, /DCS0, /DCKE, DQMH, DQML, /DREQ, /DGRNT, BC32K, VDAT[3:0], CP, LOAD, DF, FRAME, DISPON, VIDDONE,
PWRCS, TXD, RXD, /CS0∼3, /MCS0∼3, CHIFS, CHICLK, CHIDOUT, CHIDIN, IO[6:0], SPICLK, SPIOUT, SPIIN, SIBSYNC, SIBOUT,
SIBMCLK, SIBCLK, RXPWR, IROUT, /CRAD1WAIT, /CARD2WAIT, MIOX[2:0]
4. A[12:], ALE, /RD, /WE /SAS0∼3, /CARDREG, /IOWR, /CARD1CSL, /CARD1CSH, /CARD2CSL, /CARD2CSH
5. DCLKOUT
6. MBUSCLK, MBUSDATA
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
13
AC ELECTRICAL CHARACTERISTICS
PR31100 TIMING – DEFINITION OF AC SPECIFICATION
0.8V
2.0V
DELAY
SETUP HOLD
2.2V
0.8V
2.2V
0.8V
2.2V
0.8V
OUTPUTS
INPUTS
0.8V
CC
0.2V
CC
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
14
MEMORY INTERFACE
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 DCLKOUT high time – 5 – ns
2 DCLKOUT low time – 5 – ns
3 DCLKOUT period – 12.5 – ns
Rising – 4 ns
4
Delay DCLKOUT to ALE
Falling – 3 ns
4 Delay DCLKOUT to A[12:0] – – 8 ns
4 Delay DCLKOUT to D[31:16] – – 8 ns
4 Delay DCLKOUT to D[15:0] – 1.5 8 ns
Rising – 10 ns
4
Delay DCLKOUT to /CS3–0
Falling – 10 ns
Risng – 8 ns
4
Delay DCLKOUT to /RD
Falling – 7 ns
Rising – 5 ns
4
Delay DCLKOUT to /WE
Falling – 4 ns
Rising – 1.5 ns
4
Delay DCLKOUT to /SAS3–0
Falling – 1.5 ns
Rising – 9 ns
4
Delay DCLKOUT to /CARDxCSx
Falling – 8 ns
Rising – 12 ns
4
Delay DCLKOUT to /CARDDIR
Falling – 11 ns
Rising – 9 ns
4
Delay DCLKOUT to /CARDREG
Falling – 10 ns
Rising – 10 ns
4
Delay DCLKOUT to /IORD
Falling – 9 ns
Rising – 9 ns
4
Delay DCLKOUT to /IOWR
Falling – 9 ns
Rising – 6 ns
4
Delay DCLKOUT to /RAS0
Falling – 6 ns
Rising 1.5 8 ns
4
Delay DCLKOUT to /RAS1
Falling 1.5 9 ns
Rising 1.5 8 ns
4
Delay DCLKOUT to DQMH/L
Falling 1.5 9 ns
Rising 1.5 7 ns
4
Delay DCLKOUT to /DCS0
Falling 1.5 6 ns
Rising 1.5 8 ns
4
Delay DCLKOUT to DCKE
Falling 1.5 8 ns
Rising – 10 ns
4
Delay DCLKOUT to /MCS3–0
Falling – 10 ns
5 D[31:16] to DCLKIN Setup time – 2 – ns
6 D[31:16] to DCLKIN Hold time – 1 – ns
5 D[15:0] to DCLKIN Setup time – 1 – ns
6 D[15:0] to DCLKIN Hold time – 1.5 – ns
7 DCLKOUT to DCLKIN Board Delay time – 0 3 ns
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
15
MEMORY INTERFACE TIMING DIAGRAMS
1
3
2
4
DCLKOUT
MEMORY
OUTPUTS
6
DCLKIN
MEMORY
INPUTS
5
Figure 2. Memory Input Timing
DCLKOUT
DCLKIN
7
Figure 3. DCLKOUT to DCLKIN
Figure 1. Memory Output and Clock Timing
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
16
CHI
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 CHICLK high time – 100 – ns
2 CHICLK low time – 100 – ns
3 CHICLK period – 225 – ns
Rising – 5 ns
4
Delay CHICLK Rising to CHIDOUT (Master)
Falling – 5 ns
Rising – 5 ns
7
Delay CHICLK Falling to CHIDOUT (Master)
Falling – 5 ns
Rising – 5 ns
4
Delay CHICLK Rising to CHIFS (Master)
Falling – 5 ns
Rising – 5 ns
7
Delay CHICLK Falling to CHIFS (Master)
Falling – 5 ns
Rising – 10 ns
4
Delay CHICLK Rising to CHIDOUT (Slave)
Falling – 10 ns
Rising – 10 ns
7
Delay CHICLK Falling to CHIDOUT (Slave)
Falling – 10 ns
Rising – 10 ns
4
Delay CHICLK Rising to CHIFS (Slave)
Falling – 10 ns
Rising – 10 ns
7
Delay CHICLK Falling to CHIFS (Slave)
Falling – 10 ns
5 CHIDIN to CHICLK Rising Setup time (Master) – 20 – ns
6 CHIDIN to CHICLK Rising Hold time (Master) – 20 – ns
8 CHIDIN to CHICLK Falling Setup time (Master) – 20 – ns
9 CHIDIN to CHICLK Falling Hold time (Master) – 20 – ns
5 CHIFS to CHICLK Rising Setup time (Slave) – 20 – ns
6 CHIFS to CHICLK Rising Hold time (Slave) – 20 – ns
8 CHIFS to CHICLK Falling Setup time (Slave) – 20 – ns
9 CHIFS to CHICLK Falling Hold time (Slave) – 20 – ns
5 CHIDIN to CHICLK Rising Setup time (Slave) – 20 – ns
6 CHIDIN to CHICLK Rising Hold time (Slave) – 20 – ns
8 CHIDIN to CHICLK Falling Setup time (Slave) – 20 – ns
9 CHIDIN to CHICLK Falling Hold time (Slave) – 20 – ns
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
17
CHI TIMING DIAGRAMS
1
3
2
4
CHICLK
CHI
OUTPUTS
6
CHICLK
CHI
INPUTS
5
Figure 5. CHI Input Timing (CHIRXEDGE = 1)
7
CHICLK
CHI
OUTPUTS
Figure 6. CHI Output and Clock Timing (CHITXEDGE = 0)
9
CHICLK
CHI
INPUTS
8
Figure 7. CHI Input Timing (CHIRXEDGE = 0)
Figure 4. CHI Output and Clock Timing (CHITXEDGE = 1)
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
18
MAGIC BUS
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 MBUSCLK high time – 10 – ns
2 MBUSCLK low time – 10 – ns
3 MBUSCLK period – 25 – ns
Rising – 2 ns
4
Delay MSBUSCLK Rising to MBUSDATA (Master)
Falling – 2 ns
Rising – 2 ns
7
Delay MSBUSCLK Falling to MBUSDATA (Master)
Falling – 2 ns
5 MBUSDATA to MBUSCLK Rising Setup time (Slave) – 4 – ns
6 MBUSDATA to MBUSCLK Rising Hold time (Slave) – 5 – ns
8 MBUSDATA to MBUSCLK Falling Setup time (Slave) – 4 – ns
9 MBUSDATA to MBUSCLK Falling Hold time (Slave) – 5 – ns
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
19
MAGIC BUS TIMING DIAGRAMS
1
3
2
4
MBUSCLK
MBUSDATA
6
MBUSCLK
MBUSDATA
5
Figure 9. Magic Bus Input Timing (Slave, RCVPHAPOL = 0)
7
MBUSCLK
MBUSDATA
Figure 10. Magic Bus Output and Clock Timing (Master, PHAPOL = 0)
9
MBUSCLK
MBUSDATA
8
Figure 11. Magic Bus Input Timing (Slave, RCVPHAPOL = 1)
Figure 8. Magic Bus Output and Clock Timing (Master, PHAPOL = 1)
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
20
SIB
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 SIBMCLK high time – 20 – ns
2 SIBMCLK low time – 20 – ns
3 SIBMCLK period – 50 – ns
4 Delay SIBMCLK to SIBSCLK Rising – 5 ns
5 Delay SIBMCLK to SIBSCLK Falling – 5 ns
Rising – 2 ns
6
Delay SIBSCLK Rising to SIBSYNC
Falling – 2 ns
Rising – 2 ns
6
Delay SIBSCLK Rising to SIBDOUT
Falling – 2 ns
7 SIBDIN to SIBSCLK Rising Setup time – 20 – ns
8 SIBDIN to SIBSCLK Rising Hold time – 0 – ns
SIB TIMING DIAGRAMS
1
3
2
5
SIBMCLK
SIBSCLK
4
6
SIBSCLK
SIB
OUTPUTS
87
SIBDIN
Figure 13. SIB Timing
Figure 12. SIB CLK Timing
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
21
SPI
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 SPIMCLK high time – 120 – ns
2 SPICLK low time – 120 – ns
3 SPICLK period – 250 – ns
4 Delay SPICLK Rising to SPIOUT Rising – ns
4 Delay SPICLK Rising to SPIOUT Falling – ns
7 Delay SPICLK Falling to SPIOUT Rising – ns
7 Delay SPICLK Falling to SPIOUT Falling – ns
8 SPIIN to SPICLK Rising Setup time – 15 – ns
9 SPIIN to SPICLK Rising Hold time – 15 – ns
5 SPIIN to SPICLK Falling Setup time – 15 – ns
6 SPIIN to SPICLK Falling Hold time – 15 – ns
SPI TIMING DIAGRAMS
4
SPICLK
SPIOUT
65
SPIIN
21
3
Figure 14. SPI Timing (PHAPOL = 1)
7
SPICLK
SPIOUT
98
SPIIN
Figure 15. SPI Timing (PHAPOL = 0)
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
22
VIDEO
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 LOAD Pulse width – 100 1600 ns
2 Delay LOAD Falling to FRAME – 100 3200 ns
3 Delay LOAD Falling to DF – 100 3200 ns
4 Delay LOAD Falling to CP – 100 3200 ns
5 Delay CP Rising to VDAT[3:0] – – 3 ns
6 VDAT to CP Rising Setup – 15 25 ns
7 VDAT to CP Rising Hold – 15 25 ns
NOTE:
Values shown assume a 40MHz clock for the CPU, MIN and MAX values are programmable using Video Control Registers.
VIDEO TIMING DIAGRAMS
2
FRAME
1
LOAD
DF
3
CP
4
5
VDAT[3:0]
7
CP
VDAT[3:0]
6
Figure 17. Video Data Timing, 4 Bit Split LCD and 8 Bit Non-Split LCD
Figure 16. Video Timing, 4 Bit Non-Split LCD
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
23
POWER
T
amb
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 VSTANDBY to /PON Rising – 50 – ns
2 VSTANDBY to ONBUTN delay time – 2 – s
POWER TIMING DIAGRAM
VSTANDBY
ONBUTN
/PON
1
2
LIMITS
ITEM
PARAMETER
RISING/FALLING
MIN MAX
UNIT
1 /CPURES low time – 10 – ns
/CPURES
1
Figure 18.
CPU RESET
T
= 0 to +70°C, VDD = 3.3 ± 0.3V, External Capacitance = 40pF
amb
Figure 19.
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
24
LQFP208: 208-PIN PLASTIC LOW PROFILE QUAD FLAT PACKAGE
30.00
28.00
EJECTOR MARK
156
157
105
104
C 1.0
208
1
INDEX MARK
53
52
0.20 0.50
0.15
0.625
0.625
(1.40)
R0.2
R 0.2
0.50
0.10
0.15
(28.80)
(29.00)
UNIT = mm
(Drawing not to scale)
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
1996 Aug 07
25
NOTES
Philips Semiconductors Preliminary specification
MIPS
PR31100
Highly integrated embedded processor
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation
register eligible circuits under the Semiconductor Chip Protection Act.
Copyright Philips Electronics North America Corporation 1996
All rights reserved. Printed in U.S.A.
Loading...