Datasheet PM4328 Datasheet (PMC)

Download

Page 1

High Density T1/E1 Framer with Integrated M13 Multiplexer

BLOCK DIAGRAM

PM4328

TECT3

FEATURES

• Integrates 28 T1 framers, 21 E1 framers an d a full featured M13 multiplexer with DS3 framer in a single monolithic device for terminating DS3 multiplexed T1 or E1 streams.

• Four fundamental modes of operation:

• Up to 28 T1 streams M13

multiplexed into a serial DS3.

• Up to 21 E1 streams multiplexed

into a DS3 following the ITU-T G.747 recommendation (using the serial clock and data or H-MVIP system interfaces).

• DS3 M13 Multiple xer wit h ingress or

egress per link monitoring.

• Unchannelized DS3 framer mode

for access to the entire DS3 payload.

• Supports transfer of PCM data to/from

1.544 MHz and 2.048 MHz serial interface system-side devices. Also supports a fractional T1 or E1 system interface with independent ingress/ egress Nx64 Kbps rates. Supports a

2.048 MHz system-side interface for T1 mode without external clock gapping.

• Supports 8 Mbps H-MVIP on the system interface for all T1 or E1 links, a separate 8 Mbps H-MVIP system interface for all T1 or E1 CAS channels and a separate 8 Mbps H-MVIP system interface for all T1 or E1 CCS and V5.1/V5.2 channels.

• Supports a byte serial Scaleable Bandwidth Interconnect (SBI) bus interface for high density system side device interconnection of up to 84 T1 streams or 3 DS3 streams.

• Provides jitter attenuation in the T1 or E1 receive and transmit directions.

• Provides two independent de-jittered T1 or E1 recovered clocks for system timing and redundancy.

• Provides per-DS0 line loopback and per link diagnostic and line loopbacks.

• Provides an on-board programmable binary sequence generator and detector for error testing at DS3 rates. Includes support for patterns recommended in ITU-T O.151.

• Also provides PRBS generators and detectors on each tributary for error testing at DS1, E1 and NxDS0 ra tes as recommended in ITU-T O.151 and O.152.

• Provides robbed bit signaling extraction and insertion on a per-DS0 basis.

• Provides programmable idle code substitution, data and sign inversion, and digital milli watt cod e inse rtio n on a per-DS0 basi s.

• Supports the M 23 a nd C-bi t parity D S3 formats.

• Standalone unc hannelized DS3 framer mode for access to the entire DS3 payload.

• When configured to operate as a DS3 Framer, gapped transmit and receive clocks can be optionally generated for interface to link layer devices which only need access to payload data bits.

• DS3 Transmit clock source can be selected from either an external oscillator or from the recei ve side clo ck (loop-timed).

• Register level compatibility with the PM4388 TOCTL Octal T1 Framer, the PM6388 EOCTL Octal E1 Framer, the PM4351 COMET E1/T1 transceiver and the PM8313 D3MX M13 Multiplexer/Demultiplexer.

DS3

PMC-2011654 (r1) PROPRIETARY AND CONFIDENTIAL TO PMC-SIERRA, INC., AND FOR ITS CUSTOMERS’ INTERNAL USE © Copyright PMC-Sierra, Inc. 2001

DS3

Framer

with

PRBS

M13

Multiplexer

T1/E1

Framer

T1/E1

Transmitter

RJAT

PMON

TJAT

PRBS

28xT1/21xE1 Clock and Data

28xT1/21xE1 on 7 H-MVIP buses

Scaleable Bandwidt Interconnect Bus

19.44 MHz

DS3 Clock and Data

Page 2

High Density T1/E1 Framer with Integrated M13 Multiplexer

PROPRIETARY AND CONFIDENTIAL TO PMC-SIERRA, INC., AND FOR ITS CUSTOMERS’ INTERNAL USE

Utopia L2/

PM4328 TECT3

• Provides a generic 8-bit microprocessor bus interface for configuration, control and status monitoring.

• Provides a standard 5 signal P1149.1 JTAG test port for boundary scan

PACKAGE

• 324-pin fine pitch PBGA package (23 mm x 23 mm).

• Supports industria l temp erat ure rang e

C to 85 oC) operation.

(-40

board test purposes.

VOLTAGE

• Low power 2.5 V/3.3 V CMOS technology. All pins are 5 V tolerant.

APPLICATIONS

• High density T1 interfaces for multiplexers, multi-service switche s, routers and digital modems.

TYPICAL APPLICATIONS

CHANNELIZED DS3 CIRCUIT EMULATION APPLICATION

DS-3

LIU

PM4328

TECT3

SBI

• High density E1 interfaces for multiplexers, multi-ser vice switches, routers and digital modems.

• Frame Relay switches and access devices (FRADS).

• M23 Based M13 Multiplexer.

• C-Bit Parity Based M13 Multiplexer.

• Channelized and Unchannelized DS3 Frame Relay Interfaces.

Any-PHY

PM73122

AAL1gator-32

HIGH DENSITY FRAME RELAY APPLICATION

DS3 LIU

High Density T1/E1 Frame Relay Port Card

Head Office: PMC-Sierra, Inc. 8555 Baxter Place Burnaby, B.C. V5A 4V7 Canada Tel: 604.415.6000 Fax: 604.415.6200

To order documentation, send email to: document@pmc-sierra.com or contact the head office, Attn: Document Coordinator

PM4328

TECT3

PM4328

TECT3

PM4328

TECT3

SBI

PM7384

FREEDM-

84P672

All product documentation is available on our web site at: http://www.pmc-sierra.com For corporate informatio n, send email to: info@pmc-sierra.com

PCI