Datasheet PGB0040805MR, PGB0040805NR Datasheet (LITTELFUSE)

Download

Page 1

PulseGuard®Suppressors

180

www.littelfuse.com

Polymeric ESD Suppressors

PGB Series 0805 Surface Mount ESD Suppressor

Product Overview

PulseGuard ESD Suppressors help protect sensitive electronic equipment against electrostatic discharge (ESD). They supplement the on-chip protection of integrated circuitry and are best suited for lowvoltage, high-speed applications where low capacitance is important. Data ports utilizing such high-speed protocols as USB 2.0, IEEE1394 and InfiniBandSMcan benefit from this new technology. PulseGuard suppressors use polymer composite materials to suppress fast-rising ESD transients (as specified in IEC 61000-4-2 and MIL-STD-883E).

Features

• Ultra-low capacitance

• Low leakage current

• Fast response time

• 4-lines of protection

• Bi-directional

• Withstands multiple ESD strikes

• Based on industry standard 2012 package

• Compatible with pick-and-place processes

• Available in 1,000 and 5,000 piece reels (EIA-RS481)

Typical Applications

• Servers

• Laptop/Desktop Computers

• Network Hardware

• Computer Peripherals

• Digital Cameras

• External Storage

Electrical Characteristics

Trigger Voltage1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,000 V, typical

Clamping Voltage

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150V, typical

Rated Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24VDC, max

Capacitance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.055 pF

Response Time1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 1ns

Leakage Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 1nA

ESD Pulse Withstand1. . . . . . . . . . . . . . . . . . . 1,000 pulses, minimum

NOTES:

1. 8 kV direct discharge method, per IEC 61000-4-2.

2. Measured at 1 MHz.

3. Measured at 6 VDC. Testing at fast ESD pulse rates (1-20Hz) may cause a change in leakage current performance (6µA, max).

Physical Specifications

Materials:

Body: Glass Epoxy

Terminations: Tin-Lead

Soldering Parameters:

Wave solder -- 260°C, 10 seconds maximum

Reflow solder -- 260°C, 30 seconds maximum

Operating Temperature Range:

-65°C to 125°C

Ordering Information

CATALOG NUMBER PIECES PER REEL

PGB0040805MR 1,000

PGB0040805NR 5,000

Design Consideration

Because of the fast rise-time of the ESD transient, placement of PulseGuard suppressors is a key design consideration. To achieve optimal ESD suppression, the devices should be placed on the circuit board as close to the source of the ESD transient as possible. Install PulseGuard suppressors directly behind the connector so that they are the first board-level circuit component encountered by the ESD transient. They are connected from signal/data line to ground.

Page 2

PGB Series 0805 Surface Mount ESD Suppressor

PulseGuard®Suppressors

Polymeric ESD Suppressors

181

www.littelfuse.com

PULSEGUARD

SUPPRESSORS

Definitions

Trigger Voltage: The measured peak voltage across the ESD suppressor before it transitions from high to low resistance. It is manifested as a “spike” before the clamping voltage is achieved. This voltage is typically well below the damage threshold of on-chip IC protection.

Clamping Voltage: The voltage level to which the ESD impulse voltage is reduced. This is the voltage that the suppressor holds at, until the ESD transient energy is dissipated.

ESD Impulse Voltage: Also known as the ESD Threat Voltage. This is the voltage that is “zapped” into the circuit. Voltages generated by people can exceed 15 kV. The IEC 61000-4-2 defines four levels of impulse voltage for testing purposes:

SEVERITY LEVEL

AIR DISCHARGE

2 kV

4 kV

8 kV

15 kV

DIRECT

DISCHARGE

2 kV

4 kV

6 kV

8 kV

Carrier Tape Specifications

Parts are delivered on 7" (178mm) reel, paper carrier tape

DESCRIPTION

Ct- Cover tape thickness

Dd- Drive hole diameter

Ds- Drive hole spacing

- Pocket depth

- Pocket height

s - Pocket spacing

Pw- Pocket width

Tt- Carrier tape thickness

Tw- Carrier tape width

MEASUREMENT (MM)

0.06

1.50

4.00

0.58

2.21

4.00

1.45

0.65

8.00

Generalized PulseGuard Suppressor Response to ESD

(Positive and Negative Polarity ESD Pulses)

Generalized I-V Curve

(Positive and Negative Polarity ESD Pulses)

Capacitance vs. Frequency

Trigger Voltage

Voltage (V)

Clamping Voltage

Time (ns)

++++

Current (A)

Clamping Voltage

Voltage (V)

Capacitance (fF)

Frequency (GHz)

** Note: 1,000 fF = 1 pF

1.0

Trigger Voltage

2.01.50.5

Page 3

Polymeric ESD Suppressors

PGB Series 0805 Surface Mount ESD Suppressor

PulseGuard®Suppressors

182

www.littelfuse.com

Note: Pins 2 and 5 (Common) are typically connected to chassis ground. However since PulseGuard suppressors are electrically bi-directional, the system voltage bus can also be used as the ESD “dump”.

Test Set-up for IEC 61000-4-2 Waveform, 2kV-15kV

Recommended Pad Layout:

Device Dimensions:

Equivalent Circuit:

Reference Schematics:

ABCDEFG

SOLDER METHOD INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM

Wave Solder 0.029 0.74 0.029 0.74 0.028 0.71 0.050 1.27 0.025 0.635 0.020 0.51 0.011 0.279

Reflow Solder 0.029 0.74 0.029 0.74 0.028 0.71 0.050 1.27 0.025 0.635 0.020 0.51 0.011 0.279

Device under test

Tek P6156 Probe (Voltage measurement)

KeyTek pulser

2,000- 15,000 V

Ground return

Brown tip (x100)

x10

Faraday cage

.5 ohm shunt (10-5 ohms in parallel)

x10

Tektronic TDS 684B

Blue tip (x10)

Tek P6156 Probe (Current measurement)

1.27

(0.050")

0.44

(0.037")

* Dimension “a” is: 0.456 (.016") * Dimension “b” is: 0.660 (.026")

2.03

(0.080")