Datasheet PFC375-1012, PFC375-1015, PFC375-1024, PFC375-1028, PFC375-1048 Datasheet (POWER-ONE)

1

PerFormanCe POWER PFC375

The PFC375 products of the PerFormanCe Power series
incorporate high performance midrange power, active Power
Factor Correction (PFC), and high reliability to meet varied
commercial and industrial requirements.

Providing tightly regulated DC power in a wide variety of single
and multiple output configurations, the PFC375 is designed to
provide full output power with only 300 Linear Feet per Minute

(LFM) forced-air cooling (factory installed fan optional).Other
features include remote sense, power fail, logic level inhibit, and
DC power good. Main channel current sharing is provided for
redundant applications. The PFC375 is available with SAE
mountings or optional metric mountings.

The PFC375 product line is approved to the latest international
regulatory standards, and displays the CE Mark.

FEATURES

• Power Factor Correction (PFC) Meets EN61000-3-2

• Fully Regulated Outputs

• Main Output Remote Sense

• Current Share, Power Fail, and Power Good Signals

• Overtemperature, Overvoltage, and Overcurrent Protected

• Available with Metric and SAE Mountings

• Input Transient & ESD Compliance to EN61000-4-2/-3/-4/-5

• Fan Output Voltage and Optional Fan

MULTIPLE OUTPUT MODEL SELECTION CHART -

ISOLATED V3 AND V4 CAN BE USED AS POSITIVE OR NEGATIVE OUTPUTS

MODEL

OUTPUT ADJUSTMENT OUTPUT PEAK OUTPUT LINE LOAD RIPPLE & NOISE INITIAL SETTING

VOLTAGE RANGE CURRENT (NOTE 1) CURRENT (NOTE 2) REGULATION REGULATION %p-p (NOTE 3) ACCURACY

+5V 4.5V to 5.5V 3.5 - 40A 40A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4000

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

12V 11.3V to 12.6V 6A 6A 0.9% 0.9% 1% 11.9V to 12.1V

5V Fixed 3A 3A 2% 2% 2.4% 4.9V to 5.1V

+5V 4.5V to 5.5V 3.5 - 40A 40A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4001

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

12V 11.3V to 12.6V 6A 6A 0.9% 0.9% 1% 11.9V to 12.1V
12V 11.0V to 16.0V 3A 3A 0.9% 0.9% 1% 11.9V to 12.1V
+5V 4.5V to 5.5V 3.5 - 40A 40A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4002

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

12V 11.3V to 12.6V 6A 6A 0.9% 0.9% 1% 11.9V to 12.1V
24V 22.0V to 28.0V 3A 3A 0.5% 0.8% 1% 23.8V to 24.2V
+5V 4.5V to 5.5V 3.5 - 40A 40A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4004

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

15V 14.2V to 15.8V 4A 4A 0.7% 0.7% 1% 14.9V to 15.1V
15V 14.2V to 15.8V 4A 4A 0.7% 0.7% 1% 14.9V to 15.1V

SINGLE OUTPUT MODEL SELECTION CHART

MODEL

OUTPUT ADJUSTMENT MAXIMUM OUTPUT LINE LOAD RIPPLE & NOISE INITIAL SETTING

VOLTAGE RANGE CURRENT (NOTE 1) REGULATION REGULATION %p-p (NOTE 2) ACCURACY

PFC375-1012 12V 10.8V to 13.5V 30A 0.2% 0.8% 1% 11.94V to 12.06V
PFC375-1015 15V 12.0V to 17.0V 25A 0.2% 0.6% 1% 14.94V to 15.06V
PFC375-1024 24V 21.6V to 26.4V 15A 0.5% 0.8% 1% 23.88V to 24.12V
PFC375-1028 28V 25.2V to 30.8V 13.4A 0.5% 0.9% 0.9% 27.86V to 28.14V
PFC375-1048 48V 46.0V to 56.0V 7.8A 0.5% 1.0% 1% 47.52V to 48.48V

NOTES: 1) Output currents ratings are expressed with 300 LFM forced air.

2) Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth.

REV. 07/01

2

PerFormanCe POWER PFC375

MULTIPLE OUTPUT MODEL SELECTION CHART (CONT.) - ISOLATED V3 AND V4 CAN BE USED AS POSITIVE OR NEGATIVE OUTPUTS

MODEL

OUTPUT ADJUSTMENT OUTPUT PEAK OUTPUT LINE LOAD RIPPLE & NOISE INITIAL SETTING

VOLTAGE RANGE CURRENT (NOTE 1) CURRENT (NOTE 2) REGULATION REGULATION %p-p (NOTE 3) ACCURACY

+5V 4.5V to 5.5V 3.5 - 40A 40A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4005

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

(Note 4) 24V 22.0V to 28.0V 3A 3A 0.5% 0.8% 1% 23.8V to 24.2V

24V 22.0V to 28.0V 3A 3A 0.5% 0.8% 1% 23.8V to 24.2V

+24V 21.5V to 26.4V 1 - 10A 10A 0.5% 0.8% 1% 23.8V to 24.2V

PFC375-4200

+5V 4.5V to 5.5V 10A 16A 0.4% 0.8% 1% 4.98V to 5.02V
12V 11.4V to 12.6V 4A 4A 0.5% 1% 1% 11.9V to 12.1V
12V 11.4V to 12.6V 4A 4A 0.5% 1% 1% 11.9V to 12.1V

+24V 21.5V to 26.4V 1 - 10A 10A 0.5% 0.8% 1% 23.8V to 24.2V

PFC375-4201

+5V 4.5V to 5.5V 10A 16A 0.4% 0.8% 1% 4.98V to 5.02V
15V 14.2V to 16.0V 4A 4A 0.5% 0.8% 1% 14.9V to 15.1V
15V 13.7V to 16.0V 4A 4A 0.5% 0.8% 1% 14.9V to 15.1V

+5V 4.5V to 5.5V 3.5 - 50A 50A 0.4% 0.8% 1% 4.98V to 5.02V

PFC375-4500

+12V 11.3V to 12.6V 10A 16A 0.9% 0.9% 1% 11.9V to 12.1V

12V 11.3V to 12.6V 6A 6A 0.9% 0.9% 1% 11.9V to 12.1V

5V 4.5V to 5.5V 3A 3A 2% 0.9% 1% 4.9V to 5.1V

NOTES: 1) Output currents ratings are expressed with 300 LFM forced air.

2) Peak loads up to 450 Watts for 60 seconds or less are acceptable, (10% duty cycle max.). Peak power must not exceed 450 Watts.

3) Maximum peak-to-peak noise expressed as a percentage of output voltage, 20 MHz bandwidth.

4) V3 and V4 may be series connected to obtain 48V.

INPUT SPECIFICATIONS

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Input Voltage - AC Continuous input range. 85 264 VAC
Input Frequency AC Input. 47 63 Hz
Brown Out Protection Lowest AC input voltage that regulation is maintained with full rated loads. 85 VAC
Hold-Up Time Over full AC input voltage range at full rated load. 20 mS
Input Current 85 VAC at full rated load. 6ARMS
Input Protection Non-user serviceable internally located AC input line fuse, F10A, 250V.
Inrush Surge Current Internally limited by thermistor, one cycle, 25°C. 110 VAC 35

APK

220 VAC 65
Power Factor Per EN61000-3-2. 0.98 W/VA
Operating Frequency Switching frequency of main transformer. 100 kHz

OUTPUT SPECIFICATIONS

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Efficiency Full rated load, 110 VAC. Varies with distribution of loads among outputs. 68 %
Minimum Loads Single output models. 0

Multiple output models, 5V main output only. 3.5 Amps

Multiple output models, 24V main output only. 1
Ripple and Noise Full load, 20MHz bandwidth. See Model Selection Charts
Output Power 300 LFM forced air cooling required for operation. See optional fan.

Continuous power, multiple output models. 375

Watts

Peak power, all models. 450
Overshoot / Undershoot Output voltage overshoot/undershoot at turn-on. 0 V
Regulation Varies by output. Total regulation includes: line changes from 85-132 VAC or

See Model Selection Charts

170-264 VAC, changes in load starting at 20% load and changing to 100% load.
Transient Response Recovery time, to within 1% of initial set point due to a 50-100% load change,

1mS

3% max. deviation. (Main output only on multi-output units).
Turn-On Delay Time required for initial output voltage stabilization. 1 Sec
Turn-On Rise Time Time required for output voltage to rise from 10% to 90%. 10 mS

3

PerFormanCe POWER PFC375

INTERFACE SIGNALS AND INTERNAL PROTECTION

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Overvoltage Protection Provided on single output units and the main output only of multiple output units.

PFC375-30XX, PFC375-40XX, PFC375-45XX 6.0 6.4

PFC375-1012 13.5 15.5
PFC375-1015 17.0 19.5
PFC375-1024 27.0 30.7 V
PFC375-1028 30.8 35.0
PFC375-1048 60.0 70.0

PFC375-42XX 27.0 30.7
Overload Protection Fully protected against output overload and short circuit. Automatic recovery upon removal of overload condition.
Overtemperature Protection System shutdown due to excessive internal temperature, automatic reset.
Remote Sense Total voltage compensation for cable losses with respect to the main output. 250 mV
Current Share Accuracy of shared current with up to 6 parallel units. 10 %
Inhibit TTL compatible logic signal will inhibit outputs by the application of a logic low signal.

An open circuit or external TTL high signal allows normal operation.

Input Power TTL compatible logic signal. Time before regulation dropout due to

5mS

Fail Warning loss of input power at 110 VAC.
Power Good TTL compatible signal. Signal is low if main output is greater or less than 10% of nominal.
Fan Voltage Provides 170 mA current to user-supplied fan, if fan option is not selected. 12 V

SAFETY, REGULATORY, AND EMI SPECIFICATIONS

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Agency Approvals UL1950.

CSA 22.2 NO. 234/950. Approved

EN60950 (TÜV).
Dielectric Withstand Voltage Input to output. 2600 VDC
Electromagnetic Interference FCC CFR title 47 Part 15 Sub-Part B - Conducted. B

Class

EN55022 / CISPR 22 Conducted. B
ESD Susceptibility Per EN61000-4-2, level 4. 8 kV
Radiated Susceptibility Per EN61000-4-3, level 3. 10 V/M
EFT/Burst Per EN61000-4-4, level 4. ±4 kV
Input Transient Protection Per EN61000-4-5 class 3. Line to Line 1

kV

Line to Ground 2
Insulation Resistance Input to output. 10 M⍀
Leakage Current Per EN60950, 264 VAC. 2.0 mA

ENVIRONMENTAL SPECIFICATIONS

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Altitude Operating. 10k ASL Ft.

Non-Operating. 40k ASL Ft.

Operating Temperature At 100% load 0 50 °C

Derate linearly above 50°C by 2.5% per °C. At 50% load 0 70 °C
Storage Temperature -55 85 °C
Forced Air Cooling Forced air cooling of 300 LFM is required if the internal fan option is not specified.

Cooling air velocity is measured 1/4" above, at the middle of the chassis.

Airflow direction is from the input section to the output section.
Temperature Coefficient 0°C to 70°C (after 15-minute warmup). ±0.02 ±0.05 %/°C
Relative Humidity Non-Condensing. 5 95 %RH
Shock Operating: 10±3mS, 3 axis, Halfsine. 20

G

Non-operating: 10±3mS, 3 axis, Halfsine. 40
Vibration Operating: 5-32 Hz 0.02 in (DA)

32-2000 Hz Sinusoidal 1 G

RMS

Non-operating: 6.15 GRMS

4

OPTIONS

DESCRIPTION NOTES SIZE IMPACT

Fan Add “F” as a suffix to the model number to order integral fan. 10.50" x 5.00" x 2.50"

(provides required 300 LFM of forced air cooling). (266.7mm x 127.0mm x 63.5mm)

Metric Mounting Add “M” as a suffix to the model number to order chassis with 9.00" x 5.00" x 2.50"

M4 x 0.7 mounting inserts. (228.6mm x 127.0mm x 63.5mm)

PerFormanCe POWER PFC375

OVERALL SIZE: 9.00" x 5.00" x 2.50" (228.6mm x 127.0mm x 63.5mm)

OVERALL LENGTH WITH FAN: 10.50" (266.7mm)

WEIGHT: 4.3 LBS (1.95 kg)

INPUT & OUTPUT CONNECTIONS: 6-32 SCREW TERMINAL ON 0.375" (9.5mm) CENTERS

BUS BAR MAIN OUTPUT, E1 & E2, 10-32 SCREW TERMINAL

CHASSIS: 0.090" (2.3mm) ALUMINUM ALLOY, WITH CLEAR FINISH