Datasheet PCD3330-1P, PCD3330-1T Datasheet (Philips)

INTEGRATED CIRCUITS

DATA SH EET

PCD3330-1

Multistandard repertory
dialler/ringer with EEPROM

Product specification
Supersedes data of September 1992
File under Integrated circuits, IC03

1997 Jan 15

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer
with EEPROM

CONTENTS

1 FEATURES

1.1 Pulse/DTMF dialling

1.2 Number storage

1.3 Ringer

1.4 General
2 GENERAL DESCRIPTION
3 ORDERING INFORMATION
4 PINNING
5 FUNCTIONAL DESCRIPTION

5.1 Inputs/Outputs

5.1.1 COL1 to COL6, keyboard inputs

5.1.2 DMO, dial mode output

5.1.3 HOOK, on/off hook detection input

5.1.4 XTAL1 and XTAL2, oscillator input/output

5.1.5 RESET, reset input

5.1.6 CE/RF, chip enable and ringer-frequency
detect input

5.1.7 ROW1 to ROW6, keyboard outputs

5.1.8 MUTE, mute output

5.1.9 RTO, ringer tone output

5.1.10 DP/FL, pulse dialling and register recall output

5.1.11 VDD and V

5.1.12 TONE, DTMF or ringer tone output

5.1.13 PD/DTMF, pulse/tone mode selection

5.1.14 RVOL1 and RVOL2/LSE, ringer volume
outputs

5.1.15 EARTH, a/b line to earth connection

5.2 Keyboard

5.3 EEPROM organization and programming
procedures

5.3.1 EEPROM organization

5.3.2 EEPROM programming procedures

5.3.2.1 Factory EEPROM programming procedure

5.3.2.2 EEPROM programming procedures via
keyboard

5.4 Operation mode overview

5.5 Pulse/DTMF dialling function

5.5.1 Pulse/DTMF mode selection by pin

5.5.2 Pulse dialling (PD/DTMF = LOW)

5.5.3 Dual tone multi frequency (DTMF) dialling
(PD/DTMF = HIGH)

5.5.4 DTMF dialling in pulse dialling mode (mixed
mode dialling)

5.5.5 Flash or Earth function

5.5.6 Disconnect function

5.5.7 Mute function (M-key)

5.5.8 On-hook dialling control

5.6 Number storage, transmission and redial

5.6.1 Number storage and transmission

SS

PCD3330-1

5.6.2 Last number redial (1 to 24 digits)

5.6.3 Access pause by Cursor method

5.6.4 Access pause by Atlanta procedure

5.6.5 10-number repertory dialling

5.6.5.1 Chain dialling

5.6.6 3-number repertory dialling

5.6.7 Access pause storage

5.6.8 Manual access pauses

5.6.9 Storing repertory numbers

5.7 Ringer function

5.7.1 Ringer output pin selection

5.7.2 Ringer input frequency measurement

5.7.3 Ringer melodies selection

5.7.4 Ringer volume change during conversation and
ringer mode

5.7.5 Ringer repetition rate change during
conversation and ringer mode

6 LIMITING VALUES
7 HANDLING
8 DC CHARACTERISTICS
9 APPLICATION INFORMATION
10 PACKAGE OUTLINES
11 SOLDERING

11.1 Introduction

11.2 DIP

11.2.1 Soldering by dipping or by wave

11.2.2 Repairing soldered joints

11.3 SO

11.3.1 Reflow soldering

11.3.2 Wave soldering

11.3.3 Repairing soldered joints

12 DEFINITIONS
13 LIFE SUPPORT APPLICATIONS

1997 Jan 15 2

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

1 FEATURES

1.1 Pulse/DTMF dialling

• Pulse, DTMF and ‘mixed mode’ dialling

• Mixed mode dialling: start with pulse dial, end with

DTMF dial (e.g. for control of DTMF user equipment via
a pulse network)

• Number of digits per call is infinite (FIFO register)

• Flash or register recall

• Connect a/b to earth function

• Mute functions

• Disconnect function

• Supports 16 dial key: 0 to 9 and ∗, #, A, B, C and D

• Supports up to 6 × 6 keyboard and various function keys

including:
– FLASH: calibrated line-break pulse
– HOOK: toggle on-hook/off-hook or loudspeaker

on/off
– MUTE: activate/deactivate mute output
– TONE: change to DTMF dialling (mixed mode)
– DISconnect: return to on-hook state for calibrated

time

• On-hook dialling control

• Country specifications which can be stored in EEPROM

are:
– ∗ and # to be transmitted/not transmitted when

switching over to DTMF dialling mode
– mark-to-space ratio (3:2or2:1)
– 6 tone time selections (60/90, 70/70, 80/80, 100/100,

100/140 or 140/140 ms)
– 4 flash time selections (100, 115, 270 or 600 ms)
– mute output type selection (M1,
– microphone mute generated via the LSE output
– DTMF keys or Function keys selection

• On-chip voltage reference for stabilized supply and
temperature independent tone output

• On-chip filtering for low output distortion (CEPT
compatible).

M1, M2 or M2)

PCD3330-1

1.2 Number storage

• Redial by ‘cursor’ method (maximum 24 digits) stored in
internal EEPROM

• Storage for 13 repertory dial numbers (16 digits each) or
10 repertory dial numbers (20 digits each) in internal
EEPROM

• Access pause generation and termination: manually or
by ‘Atlanta’ procedure

• Function keys for: LNR, Memory recall, Store, Access
Pause and 1 key repertory

• Country specifications which can be stored in EEPROM
are:

– access pause time selection (1.5/1.0, 2.5/1.5,

3.0/3.5 or 6.0/6.0 s)
– 10 number repertory dialler selection (1 or 2 key)
– two repertory number programming procedures

(General or Germany)
– repertory length (16 or 20 digits)
– generating a keytone during program actions.

1.3 Ringer

• Ringer input frequency detection

• Function key for: Program Ringer

• Three-tone ringer with 4 different ringer frequencies

• Ringer melody generation with four signal speeds and

four output volume steps, keypad controlled

• Country specifications which can be stored in EEPROM
are:

– ringer input frequency detection selection
– ringer output selection (via DTMF tone output or

special ringer tone output)
– 4 possible ringer melodies
– 4 possible ringer repetition rates
– 4 possible ringer volumes.

1.4 General

• On-chip oscillator uses low-cost 3.58 MHz (TV colour
burst) crystal or PXE resonator

• On-chip power-on reset (typically 2.0 V)

• Supply voltage range 1.8 to 6.0 V (2.5 to 6.0 V in

EEPROM erase/write and DTMF and ringer mode).

1997 Jan 15 3

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

2 GENERAL DESCRIPTION

The PCD3330-1 is a mixed-mode multistandard repertory
dialler/ringer IC fabricated in a low threshold voltage
CMOS technology.

The (maximum 13) repertory numbers, redial and various
country specifications are stored in EEPROM so that
memory retention is guaranteed for 10 years without using
a battery back-up.

National telecommunications specifications can be fulfilled
by changing a few bytes in EEPROM which contain the
different telephone timing and dialling procedures.

The two on-chip tone generators are used for Dual Tone
Multi-Frequency (DTMF) dialling, and for generating a
melody during ringing, which is activated when a correct
incoming ringer frequency is detected.

3 ORDERING INFORMATION

TYPE

NUMBER

PCD3330-1P DIP28 plastic dual in-line package; 28 leads (600 mil) SOT117-1
PCD3330-1T SO28 plastic small outline package; 28 leads; body width 7.5 mm SOT136-1

NAME DESCRIPTION VERSION

As an output transducer for the ringer, a loudspeaker
(ringer out via tone output) or a PXE (ringer out via the
special ringer output which generates square wave ringer
tones with a peak-to-peak voltage of V
used.

The operating supply voltage is 1.8 V (2.5 V in EEPROM
erase/write and DTMF and ringer mode) to 6.0 V with a low
current consumption in all operating modes: standby,
conversation, dialling, programming and ringer.

PACKAGE

to VSS) can be

DD

1997 Jan 15 4

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

4 PINNING

SYMBOL PIN DESCRIPTION

COL1 1 sense column keyboard

input/programming EEPROM

COL2 2 sense column keyboard

input/programming EEPROM

COL3 3 sense column keyboard

input/programming EEPROM

COL4 4 sense column keyboard

input/programming EEPROM
COL5 5 sense column keyboard input
COL6 6 sense column keyboard input
DMO 7 dial mode output
HOOK 8 cradle contact input
XTAL1 9 crystal/PXE oscillator input
XTAL2 10 crystal/PXE oscillator output
RESET 11 reset input
CE/RF 12 chip enable and zero crossing for

ringer input
ROW1 13 scanning row keyboard output
ROW2 14 scanning row keyboard output
ROW3 15 scanning row keyboard output
ROW4 16 scanning row keyboard output
ROW5 17 scanning row keyboard output
ROW6 18 scanning row keyboard output
MUTE 19 mute output
RTO 20 ringer melody output
DP/FL 21 dial pulse/flash inverted output
V

SS

TONE 23 DTMF tones or ringer melody

V

DD

PD/DTMF 25 pulse/DTMF dial selection
RVOL1 26 ringer volume output 1
RVOL2/LSE 27 ringer volume output 2

EARTH 28 earth output

22 negative supply

output

24 positive supply

/loudspeaker enable output

handbook, halfpage

COL1

1

COL2

2

COL3

3

COL4

4

COL5

5

COL6

6

DMO

7

PCD3330-1

8

HOOK

XTAL1

9

XTAL2

10

RESET

11

CE/RF

12

ROW1

13

ROW2

MGG571

Fig.1 Pin configuration.

PCD3330-1

EARTH

28

RVOL2/LSE

27

RVOL1

26

PD/DTMF

25

V

24

DD

23

TONE
V

22

SS

21

DP/FL
RTO

20

MUTE

19

ROW6

18

ROW5

17

ROW4

16
1514

ROW3

1997 Jan 15 5

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5 FUNCTIONAL DESCRIPTION

5.1 Inputs/Outputs

5.1.1 COL1
The sense column inputs COL1 to COL6 and the scanning

row outputs ROW1 to ROW6 can be directly connected to
several keyboard layouts, up to a maximum 6 × 6 single
contact keyboard matrix.

Four of the sense columns are used to store the contents
of the EEPROM in the factory (see Section 5.3).

5.1.2 DMO,
This output is HIGH during the make and break times in

pulse dial mode. Its function is to lower the DC line voltage
during these pulses.

This output is LOW during DTMF dialling, during the
inter-digit-pause in pulse dial mode and during
conversation mode.

5.1.3 HOOK,

TO COL6, KEYBOARD INPUTS

DIAL MODE OUTPUT

ON/OFF HOOK DETECTION INPUT

PCD3330-1

network). When the RESET input becomes HIGH it
initializes the IC.

The RESET-pin should not be left open (not-connected) in
any circumstances.

5.1.6 CE/RF,

DETECT INPUT

As chip enable input (active HIGH) it is used to initialize
part of the system, to switch from standby to the ringer or
conversation, programming or dialling mode and to detect
line breaks.

As ringer-frequency input it measures the time between
two LOW-to-HIGH transitions, thus measuring the ringer
frequency.

5.1.7 ROW1
The scanning row outputs ROW1 to ROW6 and the sense

column inputs COL1 to COL6 can directly be connected to
several keyboard layouts (max. a 6 × 6 single contact
keyboard matrix).

CHIP ENABLE AND RINGER-FREQUENCY

TO ROW6, KEYBOARD OUTPUTS

If inputs CE and HOOK are both HIGH then the
conversation, programming or dialling mode is selected.
Switching the HOOK input LOW longer than the
reset-delay-time results in switching to the standby mode.

If CE = HIGH and HOOK = LOW the PCD3330-1 is in the
ringer mode.

5.1.4 XTAL1

AND XTAL2, OSCILLATOR INPUT/OUTPUT

Time base for the PCD3330-1 is a crystal-controlled
on-chip oscillator which is completed by connecting a

3.579545 MHz crystal or ceramic resonator (PXE)
between XTAL1 and XTAL2. The XTAL2 is the oscillator
output and can be used as driver for another oscillator
input. A low-cost quartz crystal from Philips (code number.
4322 143 04401) is available, specially for telephony
applications.
The oscillator starts when VDD reaches the operating
voltage level and CE = HIGH.

5.1.5 RESET,

RESET INPUT

When the RESET pin is connected to VSS, a reset is
generated by an internal power-on-reset circuit, which
produces an internal reset pulse every time that the supply
voltage VDD crosses the power-on-reset voltage level
(typ. 2.0 V).

Depending on the application it can be necessary to
generate a reset via an external circuit (e.g. an external RC

5.1.8 MUTE,

MUTE OUTPUT

The MUTE output is used during dialling. In the
PCD3330-1 the MUTE output has four different selectable
options:

• M1, normally LOW, but HIGH during inter-digit-pause
and make/break in pulse dial mode, during tone-on and
tone-off in DTMF mode, and during flash or earth

• M1, the inverted signal of M1

• M2, normally LOW, HIGH during make/break in pulse

dial mode, during tone-on in DTMF mode, and during
flash or earth

• M2, the inverted signal of M2.

Each time the M-key on the keyboard is pressed the MUTE
output goes to its inverted state.

5.1.9 RTO,

RINGER TONE OUTPUT

This is the special ringer output. When this output is
selected the output of the internal tone generators is not
connected to the TONE output but to this RTO output.
The ringer output signal has a peak to peak square output
voltage of VDD− VSS (this is used with a PXE transducer).

5.1.10

DP/FL, PULSE DIALLING AND REGISTER RECALL

OUTPUT

TheDP/FL output drives an external switching transistor in
pulse dial mode.

1997 Jan 15 6

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

It pulses a calibrated FLASH or register recall pulse
(if selected) when the keyboard input FLASH is pressed.

5.1.11 V
VDD and VSS are the supply terminals.

5.1.12 TONE, DTMF
In DTMF dialling mode the dual tones which are provided

at the output TONE are filtered by an on-chip switched
capacitor filter, followed by an active RC low-pass filter.
Therefore, the total harmonic distortion of the DTMF tones
fulfils the CEPT recommendations. An on-chip reference
voltage provides output tone levels independent of supply
voltages. The impedance is 100 Ω typically.

In ringer mode this TONE output can be used for
generating the ringer output tones. Whether this TONE
output or the special RTO (ringer tone) output is used is
selected via EEPROM.

5.1.13 PD/DTMF,
To select the dialling mode, this input PD/DTMF must be

connected to VDD or VSS.
PD/DTMF = HIGH (VDD) = DTMF mode.

PD/DTMF = LOW (VSS) = pulse mode.
The PCD3330-1 accept the information also during

manual dialling. Switching the input to pin PD/DTMF
changes the dialling mode after finishing the digit in
progress.

DD

AND V

SS

OR RINGER TONE OUTPUT

PULSE/TONE MODE SELECTION

PCD3330-1

microphone mute which is controlled by the M-key.
After off-hook this output is HIGH and will toggle by every
press off the M-key.

5.1.15 EARTH, a/b

The EARTH output drives an external switching transistor.
which connects the a- or b-line to earth.

It pulses a calibrated EARTH pulse (if selected) when the
keyboard input FLASH is pressed.

5.2 Keyboard

The PCD3330-1 is programmed to work with various
keyboards which can be connected to the sense column
inputs COL1 to COL6 and the scanning row outputs
ROW1 to ROW6. In this specification four examples are
given:

• Figure 2. The simplest keyboard. All basic functions are
available but only 2-key abbreviated dialling
(MEM + digit) is possible.

• Figure 3. As Fig.2 but with 3 extra 1-key abbreviated
dialling keys.

• Figure 4. As Fig.2 but the 10 repertory numbers can be
reached via M0 to M9 with 1-key abbreviated dialling.

• Figure 5. The most complex keyboard. A second
possibility for column 4 exists. This column can be
selected via EEPROM.

Keyboard entries are valid 20 ms (debounce time) after
the leading edge of a keyboard entry.

LINE TO EARTH CONNECTION

5.1.14 RVOL1

OUTPUTS

AND RVOL2/LSE, RINGER VOLUME

The RVOL1 and RVOL2 outputs can be used to control the
ringer output volume in four steps. The volume can be
changed via keyboard during ringing or conversation
mode (off-hook). The selected output level is stored in
EEPROM.

During on-hook dialling the RVOL2 output becomes the
LSE output for switching the listening-in amplifier.

When the on-hook dialling option is not selected and the
microphone mute option is active output LSE change to a

1997 Jan 15 7

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

handbook, full pagewidth

ROW 1

ROW 2

ROW 3

ROW 4

ROW 5

ROW 6

COL 1

1

4

7

*

LNR

STO

COL 2

2

5

8

0

AP

MEM M

COL 3 COL 4 COL 5

FLASH

3

6

9

#

PCD3330-1

COL 6

MGG572

handbook, full pagewidth

ROW 1

ROW 2

ROW 3

ROW 4

ROW 5

ROW 6

Fig.2 Basic keyboard.

COL 1 COL 2 COL 3 COL 4 COL 5

1

4

7

*

LNR

STO MEM M E-1 E-2 E-3

AP

2

5

8

0

3

6

9

#

FLASH

COL 6

MGG573

Fig.3 Basic keyboard with 3 extra 1-key abbreviated dialling keys.

1997 Jan 15 8

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

handbook, full pagewidth

ROW 1

ROW 2

ROW 3

ROW 4

ROW 5

ROW 6

COL 1 COL 2 COL 3 COL 4 COL 5

1

4

7

*

LNR

STO MEM M

AP

2

5

8

0

3

6

9

#

FLASH

M0

M2

M4

M6

M8

PCD3330-1

COL 6

M1

M3

M5

M7

M9

MGG574

handbook, full pagewidth

Fig.4 Basic keyboard with 10 extra 1-key abbreviated dialling keys.

ROW 1

ROW 2

ROW 3

ROW 4

ROW 5

ROW 6

COL 1 COL 2 COL 3 COL 4 COL 5

1

4

7

*

LNR

STO MEM M E-1 E-2 E-3

AP

2

5

8

0

3

6

9

#

FLASH

A/TONE

B/DIS

C/PR

D

HOOK

M0

M2

M4

M6

M8

COL 6

M1

M3

M5

M7

M9

MGG575

Fig.5 The most complex keyboard, option for column 4 is programmed into EEPROM.

1997 Jan 15 9

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

Table 1 Function of the keys

SYMBOL DESCRIPTION

0to9,∗and # Standard keyboard. In pulse dialling mode the valid keys are the 10 numeric keys (0 to 9) − the

2 non-numeric dial keys (∗ and #) have no effect on the dialling. In DTMF dialling mode the

10 numeric keys and the 2 non-numeric dial keys are valid.
A to D If selected (EEPROM bit), these keys are only valid in DTMF dialling mode.
TONE If selected, pulse to DTMF switching key (mixed mode dialling).
DIS If selected (EEPROM bit), disconnect key will activate output

telephone set turns to the ON-HOOK state for this calibrated time.
PR If selected (EEPROM bit), program ringer key. With this key the ringer output volume and ringer

repetition rate can be changed.
M0 to M9 One key abbreviated dialling, the 10 repertory numbers are directly accessible via keys M0 to M9.
LNR Last number redial.
AP Access pause key, results in inserting an access pause in the telephone number.
FLASH FLASH/EARTH key, depending on the status programmed this key starts a FLASH or an EARTH

procedure.
HOOK Hook key (for on-hook dialling/loudspeaker on/off); as long as the handset stays on the cradle

activation of this key switches the set off-hook/on-hook. When the handset is not on the cradle

activation of this key switches the loudspeaker on/off (listening-in feature).
STO STORE key.
MEM Two-key abbreviated dialling (MEM + digit), the repertory numbers M0 to M9 are also accessible via

this two-key dialling procedure.
M Mute key, each time this key is pressed and dialling is not active, the mute output goes to HIGH or

LOW depending on the previous state.
E-1 to E-3 One key abbreviated dialling, three extra repertory numbers which are only directly accessible by

keys E-1 to E-3; these numbers can only be used when the repertory length is 16 digits

(programmable in EEPROM).

DP/FL for 800 ms. In this case the

1997 Jan 15 10

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

5.3 EEPROM organization and programming procedures

5.3.1 EEPROM
The dialling, memory, and ringer options and the telephone numbers are all stored in EEPROM. By using EEPROM no

special backup requirement are necessary such as battery, current from the line, or very big capacitors.
Table 2 describes the meaning of each EEPROM byte at a repertory length of 16 and 20 digits.
Table 3 describes the meaning of each bit of all the bytes that do not contain telephone numbers.

Table 2 EEPROM organization

FUNCTION

Redial 13 bytes 0 to 12 13 bytes 0 to 12
M0 or MEM + 0 8 bytes 16 to 23 10 bytes 16 to 25
M1 or MEM + 1 8 bytes 24 to 31 10 bytes 26 to 35
M2 or MEM + 2 8 bytes 32 to 39 10 bytes 36 to 45
M3 or MEM + 3 8 bytes 40 to 47 10 bytes 46 to 55
M4 or MEM + 4 8 bytes 48 to 55 10 bytes 56 to 65
M5 or MEM + 5 8 bytes 56 to 63 10 bytes 66 to 75
M6 or MEM + 6 8 bytes 64 to 71 10 bytes 76 to 85
M7 or MEM + 7 8 bytes 72 to 79 10 bytes 86 to 95
M8 or MEM + 8 8 bytes 80 to 87 10 bytes 96 to 105
M9 or MEM + 9 8 bytes 88 to 95 10 bytes 106 to 115
E-1 8 bytes 96 to 103 not available −
E-2 8 bytes 104 to 111 not available −
E-3 8 bytes 112 to 119 not available −
Options 4bytes 120 to 123 4 bytes 120 to 123
Program Blocking 1 byte 127 1 byte 127

ORGANIZATION

REPERTORY LENGTH IS 16 DIGITS REPERTORY LENGTH IS 20 DIGITS

LENGTH BYTE PLACES LENGTH BYTE PLACES

1997 Jan 15 11

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

Table 3 Option bit status and location

FUNCTION EEPROM BYTE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

Not sending ∗ 120 XXXXXXX0
Sending ∗ 120 XXXXXXX1
Not sending # 120 X X X X X X 0 X
Sending # 120 X X X X X X 1 X
Mark to space ratio 3 : 2 120 X X X X X 0 X X
Mark to space ratio 2 : 1 120 X X X X X 1 X X
Tone/pause 60/90 ms 120 X X 0 0 0 X X X
Tone/pause 70/70 ms 120 X X 0 0 1 X X X
Tone/pause 80/80 ms 120 X X 0 1 0 X X X
Tone/pause 100/100 ms 120 X X 0 1 1 X X X
Tone/pause 100/140 ms 120 X X 1 0 0 X X X
Tone/pause 140/140 ms 120 X X 1 0 1 X X X
Flash duration 100 ms 120 0 0 X X X X X X
Flash duration 115 ms 120 0 1 X X X X X X
Flash duration 270 ms 120 1 0 X X X X X X
Flash duration 600 ms 120 1 1 X X X X X X
Mute is M1 121 X X X X X X 0 0
Mute is
Mute is M2 121 X X X X X X 1 0
Mute is
General program proc. 121 X X 0 X X X X X
General program proc. 121 X X 1 X X X X X
Repertory 16 digits 121 X 0 X X X X X X
Repertory 20 digits 121 X 1 X X X X X X
M1/M2 mute 121 0 X X X X X X X
Microphone mute 121 1 X X X X X X X

M1 121 XXXXXX01

M2 121 XXXXXX11

Access Pause time for pulse dialling (Inter-digit pause not included)

A.P. time 1.5 s 121 X X X 0 0 X X X
A.P. time 2.5 s 121 X X X 0 1 X X X
A.P. time 3.0 s 121 X X X 1 0 X X X
A.P. time 6.0 s 121 X X X 1 1 X X X

Access Pause time for DTMF dialling (Tone-off time not included)

A.P. time 1.0 s 121 X X X 0 0 X X X
A.P. time 1.5 s 121 X X X 0 1 X X X
A.P. time 3.5 s 121 X X X 1 0 X X X
A.P. time 6.0 s 121 X X X 1 1 X X X

1997 Jan 15 12

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

FUNCTION EEPROM BYTE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0

Ringer via pin RTO 122 X X X X X X X 0
Ringer via pin TONE 122 X X X X X X X 1
Ringer melody A 122 X X X X 0 0 X X
Ringer melody B 122 X X X X 0 1 X X
Ringer melody C 122 X X X X 1 0 X X
Ringer melody D 122 X X X X 1 1 X X
Ringer volume 1 122 X X 0 0 X X X X
Ringer volume 2 122 X X 0 1 X X X X
Ringer volume 3 122 X X 1 0 X X X X
Ringer volume 4 122 X X 1 1 X X X X
Ringer repetition 1 122 0 0 X X X X X X
Ringer repetition 2 122 0 1 X X X X X X
Ringer repetition 3 122 1 0 X X X X X X
Ringer repetition 4 122 1 1 X X X X X X
Ringer detection LOW 1 123 X X X X X X 0 0
Ringer detection LOW 2 123 X X X X X X 0 1
Ringer detection LOW 3 123 X X X X X X 1 0
Ringer detection LOW 4 123 X X X X X X 1 1
Ringer detection HIGH 1 123 X X X X 0 0 X X
Ringer detection HIGH 2 123 X X X X 0 1 X X
Ringer detection HIGH 3 123 X X X X 1 0 X X
Ringer detection HIGH 4 123 X X X X 1 1 X X
A to D keys 123 X X X 0 X X X X
Function keys 123 X X X 1 X X X X
Flash keytone 123 X X 0 X X X X X
EARTH function 123 X X 1 X X X X X
No keytone 123 X 0 X X X X X X
Keytone active 123 X 1 X X X X X X
No on-hook dialling 123 0 X X X X X X X
On-hook dialling control 123 1 X X X X X X X

5.3.2 EEPROM PROGRAMMING PROCEDURES
The PCD3330-1 supports four EEPROM programming procedures:

1. LNR is described in Section 5.6.2

2. Repertory numbers is described in Section 5.6.9

3. Via pins 1 to 4 (COL1 to COL4)

4. Via keyboard (can be locked with the Program Blocking byte).
Method 3 is normally used by the setmaker before the set leaves his factory.

Method 4 is most suited for usage in the field (e.g. the shop where the set is purchased).

1997 Jan 15 13

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5.3.2.1 Factory EEPROM programming procedure

The COL1 to COL4 of the PCD3330-1 can be used in the
factory to read or write the contents of the internal
EEPROM. COL1 (pin 1) is the SCL and COL2 (pin 2) is the
SDA of the I2C-bus interface, while COL3 (pin 3) and
COL4 (pin 4) determine the mode selected. In Fig.6 the
principle for this programming procedure is given.

handbook, halfpage

PCD3330-1

1
2
3
4

COL1
COL2
COL3
COL4

S1

Fig.6 Circuit diagram for the EEPROM

programming procedure.

The status of pins COL3 and COL4 is read directly after a
power-on-reset and the status can be changed with
switches S1 and S2 (open: pin is HIGH; closed: pin is
LOW).

Table 4 Function of switches S1 and S2

S1 S2 MODE

open open normal mode
closed open test mode: PCD3330-1 EEPROM write
closed closed test mode: PCD3330-1 EEPROM read

If during the programming mode S1 is opened the
programming stops and the PCD3330-1 goes to the
telephone mode. If now S1 is closed again the set stays in
telephone mode.

In the write mode the PCD3330-1 is able to read the
contents of an external RAM (128 bytes) or the PCF8581
(EEPROM) via COL1 and COL2.

In the read mode the PCD3330-1 sends the contents of its
internal EEPROM via COL1 and COL2 to the external
device.

All 128 bytes of EEPROM are read or written in each read
or write operation.

S2

SCL

SDA

MGG576

6
5

PCA8581

PCD3330-1

5.3.2.2 EEPROM programming procedures via
keyboard

This procedure is only active if EEPROM Program
Blocking byte (number 127 of the internal EEPROM) is
set to ‘FF’ hex. If this byte is ‘00’ hex it is not possible to do
the program procedures described in this chapter.
Byte 127 of the EEPROM can only be set by the factory
EEPROM programming procedure.

In the field all telephone options can be changed easily by
a special program procedure:

• Depress the STO-key (this selects the program mode)

• Depress the LNR-key (switches the program module to

storing EEPROM options

• Depress the first key of a three digit access code (the 1)

• Depress the second key of a three digit access code

(the 6)

• Depress the third key of a three digit access code (the 0)

• Depress the LNR-key again (end the access code)

• Press the byte number (last digit of the EEPROM byte

number given in Table 2)

• Press the number of the bit to change (see Table 2)

• Press 0 or 1 (this changes the EEPROM bit contents)

• Depress the LNR-key, which stores the correction into

EEPROM, now select a new byte or go to end

• End the routine by pressing the STO-key again.

If during this procedure a mistake is made correction is
possible after proper access code by pressing the
LNR-key and during access code only by STO-key.
In all cases the routine can be ended by pressing the
STO-key.

Example:
Change the mark-to-space ratio from 3 : 2 to 2 : 1. Then

bit 2 of EEPROM byte-120 has to be changed from 0 to 1.
The necessary action is as follows:

• Depress the STO-key

• Depress the LNR-key

• Depress the 1-key (first digit access code)

• Depress the 6-key (second digit access code

• Depress the 0-key (third digit access code)

• Depress the LNR-key again (end the access code)

• Press the 0-key (last digit of EEPROM byte-120 is the 0)

• Press the 2-key (bit 2 has to be changed)

• Press the 1 (changes the mark-to-space ratio to2:1)

• Press the LNR or STO-key.

1997 Jan 15 14

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

The STO-key will end the programming procedure,
whereas after the LNR-key a new byte can be selected to
have the required bit changed.

5.4 Operation mode overview

The PCD3330-1 has in total five operation modes:
standby, conversation, ringer, dialling and programming.
The state diagram is given in Fig.7.

When both CE/RF and the HOOK input are LOW the
PCD3330-1 goes to the standby mode, in which the
contents of the redial register is refreshed, the oscillator
switched off and the device enters the low current state.

A HIGH state on the CE/RF and/or the HOOK input will
cause a complete initialization of the PCD3330-1 which
means setting of the I/O pins, clearing of the RAM and
reloading the EEPROM contents into it.

PCD3330-1

5.5 Pulse/DTMF dialling function

5.5.1 P

The PCD3330-1 has two dialling modes, pulse dialling and
Dual Tone Multi Frequency (DTMF). These can be
selected via the PD/DTMF input in the following way:

PD/DTMF = HIGH (VDD) = DTMF mode.
PD/DTMF = LOW (VSS) = pulse mode.

The controller accepts the information also during manual
dialling. Switching the input to the pin PD/DTMF changes
the dialling mode after transmitting the digit in progress.

ULSE/DTMF MODE SELECTION BY PIN

handbook, full pagewidth

CE/RF = HOOK = 0

CE/RF = HOOK = 0

CE/RF = 1
HOOK = 1

STANDBY PROGRAMMING

CE/RF = 0
HOOK = 0

HOOK = 0
CE/RF = AC

CE/RF = HOOK = 0

DIALLING

end dial

CONVERSATION

CE/RF = 1
HOOK = 1

RINGER

start dial

STO-key

STO-key

MGG577

Fig.7 State diagram of the PCD3330-1 dialler/ringer.

1997 Jan 15 15

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5.5.2 PULSE DIALLING (PD/DTMF = LOW)
The keyboard entry initiates a recall of a previously stored

number or is a simultaneous keying-in and pulsing-out
activity, with storing for possible later recall. If in the
recalled number or at keying-in the keys A,B,C or D
(options A to D keys selected) are used these digits are
not transmitted.
If at keying-in the keys ∗ or # are used this results in a
switch over to DTMF dialling. Normally, keying in is faster
than pulsing-out (fed from the redial register). Pulse
sequences start with an inter-digit pause of 840 ms
duration, followed by a sequence of pulses corresponding
to the present digit in store. Each pulse starts with a mark
(line break) followed by space (line make).
The pulse period is 100 ms with a mark-to-space ratio of
3:2or2:1 (mark-to-space ratio selection). After
transmission of a digit, the next digit is processed, again
starting with an inter-digit pause. The pulses are available

DP/FL output and can be used to drive an external

at the
switching transistor in pulse dialling mode.
The transmission IC is put in the dialling mode by means
of output MUTE.

PCD3330-1

Output MUTE has several programmable options, MUTE
can be configured as M1,
timing diagram of these output possibilities is given.
After completion of the number string the circuit changes
from dialling mode to conversation mode.

5.5.3 D

UAL TONE MULTI FREQUENCY (DTMF) DIALLING

(PD/DTMF = HIGH)

The PCD3330-1 converts keyboard inputs into data for the
on-chip DTMF generator. Tones are transmitted via output
TONE with six programmable minimum tone burst/pause
durations of 60/90, 70/70, 80/80, 100/100,
100/140 or 140/140 ms. The maximum tone burst duration
is equal to the key depression time. With redial and
repertory dialling tones are automatically fed at the
programmed rate. Again the MUTE output has several
programmable options namely, M1, M1, M2 and M2.
In Fig.9 the timing diagram of these output possibilities is
given.

M1, M2 and M2. In Fig.8 the

handbook, full pagewidth

KEYBOARD

ENTRY

DP/FL

handset lifted

CE

23

M1

M1

M2

M2

t

m

t

b

t

id

t

m

t

b

t

id

Fig.8 Timing diagram in pulse mode, showing DP/FL and MUTE outputs.

handset replaced

MGG578

1997 Jan 15 16

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

CE

TONE

M1

M1

M2

M2

handset lifted

23

t

on

t

off

handbook, full pagewidth

KEYBOARD

ENTRY

PCD3330-1

handset replaced

t

on

t

off

MGG579

Fig.9 Timing diagram in DTMF mode, showing MUTE outputs.

5.5.4 DTMF DIALLING IN PULSE DIALLING MODE (MIXED

MODE DIALLING

)

If the controller is set to the pulse dial mode (pin PD/DTMF
is LOW), activation of keys TONE, ∗ or # changes the
dialling mode to DTMF.
Its entry is stored in the redial register and it generates
automatically an access pause, after which the following
digits are transmitted in the DTMF mode.
The digits entered after keys TONE, ∗ or # are not
transmitted in the redial mode. The TONE key is never
transmitted in the redial mode.
The TONE key is never transmitted, whether ∗ or # are
transmitted depends on the selected option.
A second touch of the TONE key is ignored. The ∗ or #
keys pressed after a switch over to DTMF dialling are all
transmitted.

If the controller is initially set to the DTMF mode (pin
PD/DTMF is HIGH), activation of TONE is ignored and the
∗ or # are stored in the redial register and transmitted in
DTMF mode.

5.5.5 F

LASH OR EARTH FUNCTION

Whether the Flash or Earth function is activated by the
FLASH key is programmed in the EEPROM.

If the FLASH function is selected a calibrated FLASH pulse
(recall register) is generated on the

DP/FL output and the
MUTE output is active.
The calibrated FLASH time is programmed for 100, 115,
270 or 600 ms in EEPROM.

If the EARTH (‘Connect a/b to earth’) function is selected,
the EARTH output becomes HIGH and the MUTE output
is active. The time of earth connection is 400 ms.

When the FLASH key is pressed the telephone number
entered before the FLASH key is stored in the redial
register (EEPROM).

• After dialling 1-2-3-’FLASH’ - on-hook Redial is

1-2-3

• After dialling 1-2-3-‘FLASH’ - 4 - 5 - 6 - on-hook

Redial is 4 -5-6.

5.5.6 D

ISCONNECT FUNCTION

This DIS (disconnect) key is only available if the function
key option is programmed. Touching the DIS key activates
output DP/FL for 800 ms. In this case the telephone set
turns to the ON-HOOK state for this calibrated time, after
which it comes back to the OFF-HOOK mode.

1997 Jan 15 17

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5.5.7 MUTE FUNCTION (M-KEY)
When no dialling or programming is active, every time this

M-key is pressed the MUTE output goes to the active or
inactive state depending on its previous status.
When the MUTE output is in the active state and another
key is pressed then the MUTE output is switched back to
the inactive state.

When there is the on-hook dialling is not selected and the
Microphone mute flag in EEPROM is HIGH, every press
off the M-key will result in the inverted value of the
RVOL2/LSE output. At off-hook the status of this output is
HIGH.

5.5.8 O
If required, the on-hook dialling control feature can be

selected by programming the corresponding bit in
EEPROM.
When this on-hook dialling feature is selected, the power
supply to the PCD3330-1 must be maintained during
on-hook.

In telephone sets developed for on-hook dialling
(an electronic hook-switch must be present) activation of
the HOOK-key during on-hook results in an off-hook via
the DP/FL output, and the LSE output becomes HIGH.
As long as the handset stays on the cradle a new
activation of the HOOK-key results in an on-hook, and the
LSE output becomes LOW.

When during on-hook dialling the handset is lifted from the
cradle the on-hook dialling mode is switched off and the
LSE output is set to the active (LOW) state.

When the handset is off-hook (not on the cradle) activation
of this HOOK-key switches the loudspeaker on
(LSE = HIGH) or off (LSE = LOW) (listening-in feature).

N-HOOK DIALLING CONTROL

PCD3330-1

Up to 24 digits can be stored in the redial register. After the
work register overflows, a 10 digits First-In-First-Out
register (FIFO) takes over as buffer and the contents of the
work register is now copied to the redial register.
After transmitting the first digit of the FIFO register this
position is automatically cleared to provide space for the
storage of new data. In this way, the total number that can
be transmitted is unlimited, provided the key-in rate is not
excessive. However, if the FIFO register overflows (more
than 10 digits in store) further input is ignored.

Input digits are transmitted immediately with minimum
transmission time. Transmission continues for as long as
digits are input.

5.6.2 L
If the first key pressed and released is LNR, the stored

number in the redial register is recalled and transmitted
immediately.

The LNR key can be used in two other ways, known as the
‘cursor’ method and the ‘Atlanta’ procedure, to allow
external numbers to be redialled from a PABX with an
appropriate access pause.

5.6.3 A
If the first key entered is not LNR but numerical digits,

these digits are compared to those held in store. As long
as the digits entered equal those stored, the redial register
in not cleared and dialling can be continued by pressing
the redial key. The already dialled part is not redialled.
Redial is inhibited as soon an entry is unequal to the digit
at the same position held in store.

This ‘cursor’ method allows an access code to be entered
and access confirmation tone to be received before an
external number is redialled.

AST NUMBER REDIAL (1 TO 24 DIGITS)

CCESS PAUSE BY CURSOR METHOD

5.6 Number storage, transmission and redial

5.6.1 NUMBER STORAGE AND TRANSMISSION
If the first key pressed at off-hook is 0 to 9 in pulse dialling

or 0 to 9,∗ and # in DTMF dialling mode, digits are entered
into the work register and compared with the previous
entries stored in the redial register. As long as the newly
dialled digits are equal to those stored, the contents of the
redial register are unaffected.

When the newly pressed digit is different from the one
stored in the redial register the contents of the work
register are copied to the redial register when going
on-hook (or every other action equal to on-hook).

1997 Jan 15 18

5.6.4 A
If the first key entered is the redial key, but this key is kept

down, then only the first digit held in the redial register is
transmitted. After releasing the redial key the remaining
digits held in the redial register are dialled.

The ‘Atlanta’ procedure allows a single stored access digit
to be transmitted, but redial of the external number to be
delayed until access has been confirmed.

5.6.5 10­The PCD3330-1 includes a 10-number repertory dialler,

16 or 20 digits each, which is accessible with a one or
two-key procedure.

CCESS PAUSE BY ATLANTA PROCEDURE

NUMBER REPERTORY DIALLING

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

The 10 repertory numbers can be recalled with the
M0 to M9 keys or by pressing the MEM key followed by a
numeric digit from 0 to 9.
If the keyboard matrix contains the keys M0 to M9, each of
the 10 repertory numbers can be recalled using the
corresponding single key.
If the keyboard matrix contains the MEM key each of the
10 repertory numbers can be recalled by depressing MEM
followed by the numeric digit 0 to 9.

The maximum length of these repertory numbers is
16 or 20 digits (depending on the programmed repertory
number length) including the manually stored access
pauses.

5.6.5.1

Repertory numbers can be dialled-out after or before
entering manual dialling or last number redial and by
entering the memory locations in successive order (‘chain
dialling’).
During transmission of a number recalled from the
memory location, the controller does not accept keyboard
entries. Dialling can be continued as soon as the number
under transmission is completed.
Note that the last memory location which is transmitted is
stored in the redial register.

Chain dialling

PCD3330-1

The maximum length of these repertory numbers is
16 digits including the manually stored access pauses.
The chain dialling procedure is equal to that explained in
10-number repertory dialling.

5.6.7 A
If during entering a telephone number via keyboard for

normal dialling or during repertory number programming
the AP-key (access pause key) is pressed, then an access
pause is stored in the redial or repertory dial register.

5.6.8 M
The AP-key is used to insert an access pause during

manual dialling. It is possible to select between four
possible access pause times for each dialling mode:

For pulse dialling 1.5, 2.5, 3.0 or 6.0 s (inter-digit pause not
included).
For DTMF dialling 1.0,1.5, 3.5 or 6.0 s (inter-digit pause
not included).

5.6.9 S
When the Keytone active bit in EEPROM is HIGH, every

key activation in programming mode will result in a keytone
of 1046 Hz lasting 200 ms.

CCESS PAUSE STORAGE

ANUAL ACCESS PAUSES

TORING REPERTORY NUMBERS

5.6.6 3­When the repertory length programmed in EEPROM is set

to 16 digits, the PCD3330-1 includes also an additional
3-number repertory dialler.
These repertory numbers are only accessible with the
one-key procedure.

These 3 repertory numbers can only be recalled with the
E-1 to E-3 keys.

Table 5 One-key access repertory number mode (M0 to M9 and E-1 to E-3)

Set in operation mode set in operation mode
Depress STO (store key) depress STO (store key)
Telephone number location (M0 to M9/E-1 to E-3)
Depress STO (store key) telephone number
Location (M0 to M9/E-1 to E-3) STO (store key)

NUMBER REPERTORY DIALLING

GENERAL PROCEDURE GERMAN PROCEDURE

The store mode starts after going off-hook and depressing
the STO-key. With the PCD3330-1 a selection can be
made between two store modes, the ‘General’ and the
‘German’.

Repertory numbers can be stored into EEPROM via the
one-key access or the two-key access method and
following the German or General storing procedures. This
is detailed in Tables 5 and 6.

1997 Jan 15 19

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

Table 6 Two-key access repertory number mode (MEM + 0 to 9)

GENERAL PROCEDURE GERMAN PROCEDURE

Set in operation mode set in operation mode
Depress STO (store key) depress STO (store key)
Telephone number depress MEM (location key)
Depress STO (store key) depress 0 to 9 (real location)
Depress MEM (location key) telephone number
Depress 0 to 9 (real location) depress STO (store key)

Memory locations can be cleared by following the same procedure as for storing a number, without actually entering a
number.

5.7 Ringer function

The PCD3330-1 has a three-tone melody ringer with the following characteristics:

• Ringer output pin selection

• Ringer input frequency measurement

• Ringer melodies selection

• Ringer volume change during conversation and ringer mode

• Ringer repetition rate change during conversation and ringer mode.

In Fig.10 the timing diagram of the ringer function is given.

handbook, full pagewidth

incoming

ringer

CE/RF

power on

reset

melody

max.

200 ms

800 Hz 1067 Hz 1333 Hz 800 Hz 1067 Hz 1333 Hz

T

tone

T

tone

T

tone

max.

200 ms

MGG580

Fig.10 The timing diagram of the ringer function.

1997 Jan 15 20

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5.7.1 RINGER OUTPUT PIN SELECTION
The ringer signal is sent via the special Ringer Tone

Output (RTO) or via the TONE output depending on the
option selected.
When a loudspeaker is used as a transducer, it is better to
use the TONE output. One of the internal tone generators
directly supplies this output with V
The RTO output signal, used for PXE transducers, is a
block with a peak-to-peak output voltage of VDD− VSS.

5.7.2 R
The melody ringer becomes active for all incoming ringer

frequencies higher then the ringer detection LOW
frequency and lower then the ringer detection HIGH
frequency supplied to the CE/RT input of the PCD3330-1.
The ringer detection LOW and ringer detection HIGH
frequencies are selected such that it is possible to use this
PCD3330-1 for both single and double phase rectifier
applications. It is possible to select one out of four ringer
detection LOW and four ringer detection HIGH frequencies
options which are given below:

• Ringer detection LOW 1: 16 Hz

• Ringer detection LOW 2: 20 Hz

• Ringer detection LOW 3: 32 Hz

• Ringer detection LOW 4: 40 Hz

• Ringer detection HIGH 1: 35 Hz

• Ringer detection HIGH 2: 60 Hz

• Ringer detection HIGH 3: 70 Hz

• Ringer detection HIGH 4: 120 Hz.

5.7.3 R
The ringer melody generator can select out of four different

ringer melody options (stored in EEPROM), given in
Table 7.

INGER INPUT FREQUENCY MEASUREMENT

INGER MELODIES SELECTION

RMS

= 181 mV.

PCD3330-1

5.7.4 RINGER VOLUME CHANGE DURING CONVERSATION

AND RINGER MODE

The ringer volume can be controlled by the port pins
RVOL1 and RVOL2 and its value is stored in EEPROM.

The output volume can be changed:

• Via the EEPROM programming procedure (see

Section 5.3.2)

• During conversation mode, when the function keys

option is chosen, with a special key sequence

• During active ringer by a simple key press.
In Conversation mode the procedure is as follows:

• Put the set in conversation mode (supply necessary)

• Depress PR (ringer program key)

• Press one of the four acceptable volume keys (1 to 4);

see Table 8.

Table 8 Ringer volume control, conversation mode

KEY RVOL1 RVOL2

1 0 0 (minimum output power)
210
301
4 1 1 (maximum output power)

The newly selected value is directly stored into EEPROM.
During active ringing the PR key is not used, the procedure

is as follows:

• Activate the ringer (only then this volume correction is

possible)

• Press one of the four acceptable volume keys (1 to 4);

see Table 9.

Table 7 Ringer melody options

RINGER MELODY

Ringer melody A 738 826 925
Ringer melody B 800 1067 1333
Ringer melody C 1455 1621 1810
Ringer melody D 1995 2223 2510

1997 Jan 15 21

FREQ. 1

(Hz)

FREQ. 2

(Hz)

FREQ. 3

(Hz)

Table 9 Ringer volume control, active ringer mode

KEY RVOL1 RVOL2

1 0 0 (minimum output power)
210
301
4 1 1 (maximum output power)

The newly selected value is directly stored into EEPROM.

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

5.7.5 RINGER REPETITION RATE CHANGE DURING

CONVERSATION AND RINGER MODE

The generated melody is built up out of three frequencies.
These frequencies are generated successively in a
selected repeat frequency.
There are four steps and they can be changed:

• Via the EEPROM programming procedure (See
Section 5.3.2)

• During conversation mode, when the function keys
option is chosen, with a special key sequence

• During active ringer by a simple key press.

In conversation mode the procedure is as follows:

• Put the set in conversation (supply necessary)

• Depress PR (ringer program key)

• Press one of the four acceptable repeat frequency keys

(9, ∗, 0 or #) see Table 10.

PCD3330-1

The newly selected value is directly stored into EEPROM.
During active ringing the PR key is not used, the procedure

is as follows:

• Active the ringer (only then this repetition rate correction
is possible)

• Press one of the four acceptable repeat frequency keys
(9, ∗, 0 or #) see Table 11.

Table 11 Ringer repetition rate selection, active ringer

mode

KEY

9 7 47.6
∗ 11 30.3
0 15 22.2
# 20 16.6

FREQUENCY

(Hz)

TONE TIME

(ms)

Table 10 Ringer repetition rate selection, conversation

mode

KEY

9 7 47.6
∗ 11 30.3
0 15 22.2
# 20 16.6

FREQUENCY

(Hz)

TONE TIME

(ms)

The newly selected value is directly stored into EEPROM.

1997 Jan 15 22

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

6 LIMITING VALUES

In according with the Absolute Maximum Rating System (IEC 134).

SYMBOL PARAMETER MIN. MAX. UNIT

V

DD

V

I

I

I

I

O

P

tot

P

O

I

SS

T

stg

T

j

7 HANDLING

Inputs and outputs are protected against electrostatic discharge in normal handling. However, it is good practice to take
normal precautions appropriate to handling MOS devices (see

devices”

supply voltage −0.8 +7 V
all input voltages −0.5 VDD+ 0.5 V
DC input current −10 +10 mA
DC output current −10 +10 mA
total power dissipation − 125 mW
power dissipation per output − 30 mW
ground supply current −50 +50 mA
storage temperature −65 +150 °C
operating junction temperature − 90 °C

Data Handbook IC03, Section: General, Handling MOS

).

8 DC CHARACTERISTICS

= 1.8 to 6 V (note 1); VSS=0V; T

V

DD

≤ 100 Ω; unless otherwise specified.

R

X

= −25 to +70 °C; all voltages with respect to VSS; f

amb

= 3.579545 MHz;

osc

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Supply voltage

V

DD

supply voltage operating; note 1 1.8 − 6V

RAM data retention in

1.0 − 6V

Standby mode

Supply current

I

DD

supply current Dialling/Ringer mode;

− 0.8 1.6 mA

VDD= 3 V; note 2
Conversation/Programming

mode; V

= 3 V; note 2

DD

Standby mode

− 0.35 0.7 mA

− 1.0 5.5 µA

(notes 2 and 3);

= 1.8 V; T

at V

DD

Standby mode

amb

=25°C

−−10 µA
(notes 2 and 3);
at V

= 1.8 V; T

DD

amb

=70°C

1997 Jan 15 23

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

Inputs

V

IL

V

IH

I

LI

LOW level input voltage 0 − 0.3V
HIGH level input voltage 0.7V
input leakage current VSS≤ VI≤ V

DD

−1 − +1 µA

DD

− V

DD

Port outputs

I

OL

I

OH

I

OH1

LOW level output sink current at VDD=3V; VO= 0.4 V 0.7 3.5 − mA
HIGH level output pull-up source

current
HIGH level output push-pull

at VDD=3V; VO= 2.7 V 10 30 −µA

=3V; VO=0V − 140 300 µA

at V

DD

at VDD=3V; VO= 2.6 V 0.7 3.5 − mA

source current
Tone output (notes 1 and 4)
V

HG(RMS)

V

LG(RMS)

output RMS voltage HIGH group 158 181 205 mV

LOW group 125 142 160 mV
∆f frequency deviation −0.6 − +0.6 %
V

DC

 output impedance − 100 500 Ω

Z

O

G

v

DC voltage level −

voltage gain (pre-emphasis) of

1.5 2.0 2.5 dB

1

⁄2V

DD

− V

group

THD total harmonic distortion at T

=25°C; note 5 −−25 − dB

amb

EEPROM (notes 1, 6 and 7)
N

cyc

t

ret

endurance (erase/write cycles) 100000 −−cycles
data retention 10 −−years

Notes to characteristics

1. Tone output, EEPROM erase and EEPROM write require VDD≥ 2.5 V.

2. VIL=VSS, VIH=VDD; open drain outputs connected to VSS; all other outputs open; maximum values: external clock
at XTAL1; XTAL2 open; typical values at T

=25°C; crystal connected between XTAL1 and XTAL2.

amb

3. VIL=VSS, VIL=VDD; RESET, HOOK and CE/RT at VSS; crystal connected between XTAL1 and XTAL2;
open-drain outputs connected to VSS; all other outputs open.

4. Values are specified for DTMF frequencies only (CEPT compatible).

5. Related to the low group frequency component (CEPT compatible).

6. Verified on sampling basis.

7. After final testing the value of each EEPROM bit is typically HIGH, but this state cannot be guaranteed.

DD

V
V

1997 Jan 15 24

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

9 APPLICATION INFORMATION

A block diagram of an electronic feature phone built around the PCD3330-1 is shown in Fig.11. It comprises the following
dedicated telecom ICs:

• TEA1067 speech/transmission IC

• TEA1083A call progress monitor IC

• PCD3330-1 dialler/ringer IC.

handbook, full pagewidth

TEA1083A

CALL PROGRESS

MONITOR

LSE

PCD3330-1

DIALLER/RINGER

a/b

BSP254A

TEA1067
SPEECH

TRANSMISSION

DP/FL

SUPPLY
DTMF

PD
MUTE

b/a

RINGER IN
MELODY OUT

RINGER

HARDWARE

Fig.11 Block diagram of an electronic feature phone.

MGG581

1997 Jan 15 25

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

10 PACKAGE OUTLINES

handbook, full pagewidth

DIP28: plastic dual in-line package; 28 leads (600 mil)

D

seating plane

L

Z

28

e

b

PCD3330-1

SOT117-1

M

E

A

2

A

A

1

w M

b

1

15

c

(e )

1

M

H

pin 1 index

1

0 5 10 mm

scale

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

A

A

A

UNIT

inches

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

max.

mm

1 2

min.

max.

b

1.7

1.3

0.066

0.051

b

0.53

0.38

0.020

0.014

cD E weM

1

0.32

0.23

0.013

0.009

(1) (1)

36.0

35.0

1.41

1.34

14.1

13.7

0.56

0.54

E

14

(1)

L

3.9

3.4

M

15.80

15.24

0.62

0.60

H

E

17.15

15.90

0.68

0.63

0.252.54 15.24

0.010.10 0.60

e

1

0.15

0.13

Z

max.

1.75.1 0.51 4.0

0.0670.20 0.020 0.16

OUTLINE
VERSION

SOT117-1

IEC JEDEC EIAJ

051G05 MO-015AH

REFERENCES

1997 Jan 15 26

EUROPEAN

PROJECTION

ISSUE DATE

92-11-17
95-01-14

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

SO28: plastic small outline package; 28 leads; body width 7.5 mm

D

c

y

Z

28

15

PCD3330-1

SOT136-1

E

H

E

A

X

v M

A

pin 1 index

1

e

0 5 10 mm

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

mm

A

max.

2.65

0.10

A

1

0.30

0.10

0.012

0.004

A2A

2.45

2.25

0.096

0.089

0.25

0.01

b

3

p

0.49

0.32

0.36

0.23

0.019

0.013

0.014

0.009

UNIT

inches

Note

1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.

(1)E(1) (1)

cD

18.1

7.6

17.7

7.4

0.71

0.30

0.69

0.29

14

w M

b

p

scale

eHELLpQ

1.27

0.050

10.65

10.00

0.42

0.39

1.4

0.055

A

2

0.043

0.016

A

1.1

0.4

Q

A

3

θ

ywv θ

Z

0.9

0.4

0.035

0.004

0.016

o

8

o

0

L

p

L

0.25 0.1

0.01

(A )

1

detail X

1.1

0.25

1.0

0.043

0.01

0.039

OUTLINE
VERSION

SOT136-1

IEC JEDEC EIAJ

075E06 MS-013AE

REFERENCES

1997 Jan 15 27

EUROPEAN

PROJECTION

ISSUE DATE

91-08-13

95-01-24

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

11 SOLDERING

11.1 Introduction

There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.

This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our

“IC Package Databook”

11.2 DIP

11.2.1 S

The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.

The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.

11.2.2 R

Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.

11.3 SO

11.3.1 REFLOW SOLDERING

Reflow soldering techniques are suitable for all SO
packages.

OLDERING BY DIPPING OR BY WA VE

EPAIRING SOLDERED JOINTS

(order code 9398 652 90011).

). If the

stg max

PCD3330-1

Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.

Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.

11.3.2 W
Wave soldering techniques can be used for all SO

packages if the following conditions are observed:

• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.

• The longitudinal axis of the package footprint must be
parallel to the solder flow.

• The package footprint must incorporate solder thieves at
the downstream end.

During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.

Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.

A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.

11.3.3 R

Fix the component by first soldering two diagonally­opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.

AVE SOLDERING

EPAIRING SOLDERED JOINTS

Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.

1997 Jan 15 28

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with

PCD3330-1

EEPROM

12 DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.

13 LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.

1997 Jan 15 29

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

NOTES

PCD3330-1

1997 Jan 15 30

Philips Semiconductors Product specification

Multistandard repertory dialler/ringer with
EEPROM

NOTES

PCD3330-1

1997 Jan 15 31

Philips Semiconductors – a worldwide company

Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,

Tel. [phone], Fax. [phone]
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213,

Tel. [phone], Fax. [phone]
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,

220050 MINSK, Tel. [phone], Fax. [phone]

Belgium: see The Netherlands
Brazil: seeSouth America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15thfloor,

51 James Bourchier Blvd., 1407 SOFIA,
Tel. [phone], Fax. [phone]

Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. [phone]

China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. [phone], Fax. [phone]

Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,

Tel. [phone], Fax. [phone]
Finland: Sinikalliontie 3, FIN-02630 ESPOO,

Tel. [phone], Fax. [phone]/xxx
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,

Tel. [phone], Fax. [phone]
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,

Tel. [phone], Fax. [phone]
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,

Tel. [phone], Fax. [phone]

Hungary: seeAustria
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.

Worli, MUMBAI 400 018, Tel. [phone], Fax. [phone]

Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,

Tel. [phone], Fax. [phone]
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180,

Tel. [phone], Fax. [phone]
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,

20124 MILANO, Tel. [phone], Fax. [phone]
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,

Tel. [phone], Fax. [phone]
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,

Tel. [phone], Fax. [phone]
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,

Tel. [phone], Fax. [phone]
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,

Tel. [phone]

Middle East: see Italy

Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,

Tel. [phone], Fax. [phone]
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,

Tel. [phone], Fax. [phone]
Norway: Box 1, Manglerud 0612, OSLO,

Tel. [phone], Fax. [phone]
Philippines: Philips Semiconductors Philippines Inc.,

106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. [phone], Fax. [phone]

Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. [phone], Fax. [phone]

Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,

Tel. [phone], Fax. [phone]
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,

Tel. [phone], Fax. [phone]

Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,

2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. [phone], Fax. [phone]

South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. [phone], Fax. [phone]

Spain: Balmes 22, 08007 BARCELONA,
Tel. [phone], Fax. [phone]

Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. [phone], Fax. [phone]

Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. [phone], Fax. [phone]

Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. [phone], Fax. [phone]

Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. [phone], Fax. [phone]

Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. [phone], Fax. [phone]

Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. [phone], Fax. [phone]

United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. [phone], Fax. [phone]

United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. [phone]

Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,

Tel. [phone], Fax.[phone]

For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. [phone]

© Philips Electronics N.V. 1997 SCA53
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.

Internet: http://www.semiconductors.philips.com

Printed in The Netherlands 417021/1200/02/pp32 Date of release: 1997 Jan 15 Document order number: 9397 750 01631