PREPARED
BY:
DATE:
SHAR
ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION
SPECIFICATION
f DEVICE SPECIFICATION FOR
PHOTOCOUPLER
MODEL No.
I
(Businessdealingname: PC9OOVONSZXl
1. These specification sheets include materfals protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlIned
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions menttoned below.
(Precautions)
(1) This product is designed for use in the following application areas ;
l
OA equipment
- Telecommunication equipment (Terminal)
* Tooling machines - Computers
i
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions gtven in those respective paragraphs.
* Audio visual equipment * Home appliances
PCSOOV
* Measuring equipment
I
1
-+=%An OPTO-ELECTRONIC DEVI
-
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train. automobile etc.)
- Traffic
* Other safety equipment
[
[3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as :
* Space equipment * Telecommunication equipment (for trunk lines)
l
[
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
BY
sigmk
Nuclear power control equipment * Medical equipment
* Gas leakage sensor breakers * Rescue and security equipment
DATE
PRESENTED J
BY
K. Hachimura,
Department General Manager of
Engineering Dept. .I1
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
I
1
F J-p. IJ, ,+a-3
/G&‘&&h
SHRRP CORPORATI
1. Application
This specification applies to the outline and characteristics of photocoupler
Model No. PCSOOV.
2. Outline
Refer to the attached sheet. page 3.
3. Ratings and characteristics
Refer to the attached sheet, page 3 to 5.
4. Reliability
Refer to the attached sheet, page 8.
ON
5. Outgoing inspection
Refer to the attached sheet. page 9.
6. Supplement
Isolation voltage shall be measured in the following method.
6.1
(I) Short among pins 1 to 3 on the primary side and among pins 4 to 6 on
the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
6.2 The business dealing name used for this product when ordered or delivered shall be
PCSOOVONSZX.
6.3 Package specifications
Refer to the attached sheets-2- 1 to 2-3.
SHARP CORPORATION
6.4 UL : Under preparation
6.5 Theory of operation
(1) When the forward current of above the “H+L” threshold input current (Ir,.J
is applied to the input side, the output will go “Low level”.
(2) When the forward current on the input side goes below the “L+H” threshold
input current (I,,,) is applied to the input side, the output will go “High level”.
6.6 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting,diode.
6.7 ODS materials
-
This product shall not contain the following materials.
Also, the following materials shall not be used in the production process for this product.
Materials for ODS : CFC, Halon, Carbon tetrachloride.
6.8 Brominated flame retardants
Specific brominated flame retardants such as the PBBOs and PBB, are not used
in this device at all.
7. Notes
Refer to the attached sheet-l- 1. 2.
1.1.1 -Trichloroethane (Methylchloroform)
SHARP CORPORATION
2. Outline
7.12zto.3
-
Anode inai
m
?I
m
cd
-
\ Lot No. ‘1
regulator
Pin
NOS.
Cathode N. c
Anode
connection diagram
l
7.629~0.3
and inter!‘Ial
l
2.54&O. 25
0.5fO. 1
*l) 2-digit number shall be marked according to
*2) Marking is laser marking
Product mass : Approx. 0.36g
DIN
standard.
Name
UNIT: l/l mm
PCSOOV
Outline Dimensions
(Business dealing
name : PC9OOVONSZX)
SHARP CORPORflTION
Ratings and characteristics
3.1 Absolute maximum ratings
*l The derating factors of absolute maximum ratings due to ambient temperature
are shown in Fig. 1, 2. 3.
*2 Pulse widths 100 ps, Dutyratio : 0.001
*3 AC for 1 min, 40 to 6O%RH
*4 ForlOs
SHARP CORPORATION
3.2 Electra-optical characteristics
Parameter
Forward voltage
Reverse current
Terminal capacitance
Operating supply voltage
range
Low level output voltage
High level output current
Low level supply current
High level supply current
“H-L” threshold input
current *l
-GIN. 1 TYP. 1 MAX. 1 Unit 1 -” Conditions
IR
I -
1 - 1 10 1 PA 1 Ta=25%, V,=3V
Ct ( - I30 1250 1 ,,(~;25;,V=O
vcc 131 -1151vI _
VOL 1 - 1 0.2 1 0.4 1 v 1 ~&6!&nA,Vcc=5”
bH 1 - 1 - 1 100 1 PA 1 g$=l5V
bcL 1 - 1 2.5 1 5.0 1 mA 1 Vcc=5V, 1,=4mA
E
CH I
- 1 1.0 1 5.0 1 mA 1 Vcc=5”, I,=OmA
“L-H” threshold input
current *2
Hysteresis *3
Isolation resistance
“H-L” propagation time
“L-H” propagation time
Fall time
Rise time
‘FLH /IF,,
1 0.5 1 0.7 1 0.9 1 - 1 vcc=5v, Iq=280Q
Rho I5XlO’Ol 10” 1 - 1 R ( T$..~ox$OOV
tPHL
1 3
Ta=25%
t
PLH
2 6
vcc=5v. 1,=4mA
tf
- 0.05 0.5
R,=280 0
tr
0.1 0.5
SHflRP CORPORATION
*1 I,, represents forward current when output goes from “H” to “L”.
” ‘FLH
represents forward current when output goes from “L” to “H”.
‘3 Hysteresis : IFLH/IFHL
*4 Test circuit for response time shall be shown below.
Vobge regulator
tr==tt-0.0
.?0=50n
Test circuit diaffram
output
Timing chart
SHARP CORPORATION
(Fig. 1) Forward current vs.
ambient temperature vs. ambient temperature’- !
-50
$
2 40
z
g 30
2
3 20
2
g 10
0
-25 0 25 50 7585
Ambient temperature Ta (‘c)
(Fig. 3) Total power dissipation
vs. ambient temperature
100 125
$
g
250
8
b
3 100
“a
x 50
5
0 0
(Fig. 2) Output powe
-25 0 25 50 7585
Ambient temperature Ta (‘C)
100 125
5
E
tz 200
13 170
g 150
3
2
‘El b 100
3
ifi 50
-25 0 25 50 7585 100 125
Ambient temperature Ta (‘C)
SHARP CORPOR~ITION
4. Reliability
The reliability
Test Items Test Conditions Failure Judgement Samples In)
Solderability *2 230%. 5 s n=ll, C=O
Soldering heat
Terminal strength
(Tension) 5 s/each terminal
Terminal strength Weight : 2.5N n=ll, C=O
(Bending) *3 2 times/each terminal I,,>UX1.2
Mechanical shock 15km/s’, 0.5ms ICCL>UX 1.2 n=ll, C=O
Variable frequency 100 to 2000 to lOOHz/4min
vibration 200m/sZ
Temperature 1 cycle -40% to +125% n=22,C=O
cycling (30min) (30min)
of products shall be - satisfied with items listed below.
Confidence level : 90%
LTPD : 10%/20%
‘1 Criteria Defective(C)
260%. 10 s
Weight : 5N
3 times/fX. +-Y, fZ direction
4 times/ X. Y. Z direction
20 cycles test
v,>ux 1.2
I,>UX2
vo,>ux1.2 - r
I
ccH>ux 1.2
I,,,>UX1.3
I,,<LXO.7
lFLH /‘FHL~;“x;-“2
n=ll. C=O
n=ll. C=O
n=ll. C=O
High temp. and high +85C. 85%RH. lOOOh
humidity storage
High temp. storage + 125%. lOOOh
Low temp. storage
Operation life I,= 1 OmA, vcc= 15v limit n=22,C=O
* 1 Test method, conforms to EW ED 470 1.
*2 Solder shall adhere at the area of 95% or more of immersed portion of
lead, and pin hole or other holes shall not be concentrated on one portion.
+3 Terminal bending direction is shown below.
m
k-f5 6
-40%. 1 OOOh L : Lower
&= 16mA, Ta=25%. 1 OOOh
U : Upper
specification ’
limit
specification
n=22,C=O
n=22,C=O
n=22,C=O
SHARP CORPOMTION
5. Outgoing inspection
5.1 Inspection items
(1) Electrical characteristics
v, I,. v,,. &. ICC/ ICCH’ I,,. IiqJ+. Rise. visa
(2) Appearance
5.2 Sampling method and Inspection level
A single sampling plan. normal inspection level II based on
IS0 2859 is applied. The AQL according to the inspection
items are shown below.
Defect
Major
defect Unreadable marking
Minor Appearance defect except
defect
Inspection item
Electrical characteristics
the above mentioned.
AQL
0.065
0.25
WI
SHflRP CORPORATION
Precautions for
1 For cleaning
(1) Solvent cleaning : Solvent temperature 45% or less
Immersion for 3 min or less
(2) Ultrasonic cleaning : The effect to device by ultrasonic cleaning differs
by cleaning bath size, ultrasonic power
output, cleaning time, PCB size or device mounting
condition etc. Please test it in actual using condition
and con&n that doesn’t occur any defect before starting
the ultrasonic cleaning.
(3) Applicable solvent : Ethyl alcohol, Methyl alcohol, Isopropyl alcohol
In case when the other solvent is used. there are cases that
the packaging resin is eroded. Please use the other solvent
after thorough coniirmation is performed in actual using condition.
2. Please use the same as normal integration circuit about static
electricity in order that this device is OPIC photocoupler.
3. In order to stabilize power supply line. we recommend to connect
a by-pass capacitor of 0.0 1 p F or more between Vcc and GND near the device.
Photocouplers
4. The detector which is used in this device, has parasitic diode between each pins and GND.
There are cases that miss operation or destruction possibly may be occurred if electric
potential of any pin becomes below GND level even for instant.
Therefore it shall be recommended to design the circuit that electric potential of
any pin does not become below GND level.
5. The LED used in the Photocoupler generally decreases the light emission power
by operation. In case of long operation time, please design the circuit with considering
the decreases of the light emission power of the LED. (500/6/5years)
Please decide the input current which become 2 times of MAX. I,,,
SHARP CORPORATION
6. Precautions for Soldering Photocouplers
(1) In case of soldering
to lead
260%
10 s or less
180
An example of device temperature
vs. soldering time
160
140
120
Device
temperature
- .*-
go -
.#
ed
(Cl
20
-
0’ ’ ’ ’
0 2 4
1
6 8 10 12 14 16
Soldering time (s)
(2) If solder reflow :
It is recommended that only one soldering be done at the temperature
and the time within the temperature profile as shown in the figure below.
230C
*-
*-
-0
I 1 I
18 20
e--
Solder
18OC
25C
(3) Other precautions
An infrared lamp used to heat up for soldering may cause a localized
temperature rise in the resin. So keep the package temperature within
that specified in Item (2). Also avoid immersing the resin part in the solder.
SHflRP CORPORATION
Package specification
1 Package materials
No. Name
Sleeve
1
Materials
Plastfcs with preventing
Products packaged
PUrpOSeS
static electricity
2 Stopper
Packing case Corrugated cardboard Sleeve packaged
3
4 Kraft tape Paper
Rubber Products tied
Lid of packaged case fixed
-
Model No., quantity,
5 Label
Paper inspection date and lot No.
specified
2 Package method
(1) MAX. 5Opcs. of products shall be packaged in a sleeve and
both of sleeve edges shah be fixed by stoppers.
(2) MAX. 20 sleeves above shall be packaged in a packing case
and pack a sheet of cushion at one side.
(3) Model No., quantity, inspection date and lot No. shall be marked on the label
and this label shall be put on the side of the packaging case.
(4) Case shall be closed with the lid and enclosed with kraft tape.
3 Package outline dimensions
(1) Sleeve outline dimensions
Refer to the attached sheets-2-2.
(2) Packaging case outline dimensions
Refer to the attached sheets-2-3.
SHARP CORPORATION
6.7
Length : L=520 f 2mm
Note 1) Thickness : 0.5k0.2mm
2) Outer R: 0.5mm
3) Process with applying antistatic agent.
4) Unless otherwise specified tolerances shall be f0.5mm.
(However except for deformation due to the rubber stopper in sleeve.)
4
Name
Unit : l/ lmm
Sleeve
outline dimensions
SHMiP CORPORRTION
Sleeve
Anode mark or
(With pulled portion)
\
arranged at stopper side
Wthout pulled potion.
-a-
m
I I
I I
/Stopper
mwlout pulled portlon)
20 sleev& (5lines X4sta.M *MAX.
It is impossible to mix
erent model or different
diffi
rank model in one case.
Label
Kraft tape
Name
Unit: l/lmm
Packing
case
outline dimensions
Loading...