Page 1
VER C
.
3
XXeeoonn 55 PPoowweerr LLEEDD
■
Features
●
Highest Luminous Flux
●
Super Energy Efficiency
●
Long Lifetime Operation
●
Superior ESD protection
●
Superior UV Resistance
■
Applications
●
Read lights (car, bus, aircraft)
●
Portable (flashlight, bicycle)
●
Bollards / Security / Garden
●
Traffic signaling / Beacons
●
In door / Out door Commercial lights
●
Automotive Ext
■
Absolute Maximum Rating
(Ta=25
(Ta=25℃℃℃℃))))
(Ta=25(Ta=25
Value
Item Symbol
W/B/PG
DC Forward Current IF 1400 1600 mA
Pulse Forward Current* IFP 1800 2000 mA
Reverse Voltage VR 5 5 V
Power Dissipation PD 6300 5600 mW
Operating Temperature Topr -30 ~ +85
Storage Temperature Tstg -40~ +100
Lead Soldering Temperature
*Pulse width Max.10ms Duty ratio max 1/10
■
Electrical -Optical Characteristics
Tsol
260℃/5sec
R/Y
(Ta=25
(Ta=25℃℃℃℃))))
(Ta=25(Ta=25
VF (V) IR(µA)
Part Number Color
Min. Typ. Max. Max. Typ Min. Typ. Max. Min. Typ. Max.
Unit
℃
℃
℃
CCT
(K)
■
Directivity
Luminous Flux
OSXXXDE5E1E
Anode
ESD Protection Diode
Unit:mm
Tolerance:±0.30mm
0
0
Φ
v
(lm)
3.6
BackView
λD(nm)
Cathode
2θ1/2
(deg)
IF=1400mA VR=5V
OSW4XDE5E1E
Pure White W4
OSM7XDE5E1E Warm White M7
OSM5XDE5E1E Warm White M5
OSB4XDE5E1E Blue B4
OSG5XDE5E1E Pure Green G5
OSR5XDE5E1E Red R5
OSY5XDE5E1E Yellow Y5
Note: Don’t drive at rated current more than 5s without heat sink for Xeon 5 emitter series.
3.3 3.5 4.5
3.3 3.5 4.5
3.3 3.5 4.5
3.3 3.5 4.5
3.3 3.5 4.5
2.3 2.5 3.5
2.3 2.5 3.5
10
10
10
10
10
10
10
6500
4000
3000
-
300
300
280
50
280
140
140
320
320
300
70
300
160
160
IF=1400mA
-
Typ. 6500K
-
-
455 460 465
520 525 530
620 625 630
-
585 590 595
Typ.4000K
Typ.3000K
LED & Application Technologies
http://www.optosupply.com VER A.0
140
Page 2
VER C
.
3
XXeeoonn 55 PPoowweerr LLEEDD
OSXXXDE5E1E
■ Handling of Silicone Lens LEDs
Notes for handling of silicone lens LEDs
● Please do not use a force of over 3kgf impact or pressure on the silicone lens, otherwise it will cause a catastrophic
failure.
● The LEDs should only be picked up by making contact with the sides of the LED body.
● Avoid touching the silicone lens especially by sharp tools such as Tweezers.
● Avoid leaving fingerprints on the silicone lens.
● Please store the LEDs away from dusty areas or seal the product against dust.
● When populating boards in SMT production, there are basically no restrictions regarding the form of the pick and
place nozzle, except that mechanical pressure on the silicone lens must be prevented.
● Please do not mold over the silicone lens with another resin. (epoxy, urethane, etc)
LED & Application Technologies
http://www.optosupply.com VER A.0
Loading...