Datasheet OP413 Datasheet (ANALOG DEVICES)

Low Noise, Low Drift

00286

003

www.BDTIC.com/ADI

Single-Supply Operational Amplifiers

FEATURES

Single- or dual-supply operation
Low noise: 4.7 nV/√Hz @ 1 kHz
Wide bandwidth: 3.4 MHz
Low offset voltage: 100 μV
Very low drift: 0.2 μV/°C
Unity gain stable
No phase reversal

APPLICATIONS

Digital scales
Multimedia
Strain gages
Battery-powered instrumentation
Temperature transducer amplifier

GENERAL DESCRIPTION

The OPx13 family of single-supply operational amplifiers
features both low noise and drift. It has been designed for
systems with internal calibration. Often these processor-based
systems are capable of calibrating corrections for offset and
gain, but they cannot correct for temperature drifts and noise.
Optimized for these parameters, the OPx13 family can be used
to take advantage of superior analog performance combined
with digital correction. Many systems using internal calibration
operate from unipolar supplies, usually either 5 V or 12 V. The
OPx13 family is designed to operate from single supplies from
4 V to 36 V and to maintain its low noise and precision
performance.

The OPx13 family is unity gain stable and has a typical gain
bandwidth product of 3.4 MHz. Slew rate is in excess of 1 V/s.
Noise density is a very low 4.7 nV/√Hz, and noise in the 0.1 Hz
to 10 Hz band is 120 nV p-p. Input offset voltage is guaranteed
and offset drift is guaranteed to be less than 0.8 V/°C. Input
common-mode range includes the negative supply and to
within 1 V of the positive supply over the full supply range.
Phase reversal protection is designed into the OPx13 family for
cases where input voltage range is exceeded. Output voltage
swings also include the negative supply and go to within 1 V of
the positive rail. The output is capable of sinking and sourcing
current throughout its range and is specified with 600  loads.

OP113/OP213/OP413

PIN CONFIGURATIONS

NULL

1

–IN A

+IN A

V–

OP113

2

TOP VIEW

3

(Not to Scale)

4

NC = NO CONNECT

Figure 1. 8-Lead Narrow-Body

SOIC_N

1

OUT A

–IN A

+IN A

V–

OP213

2

3

4

Figure 3. 8-Lead PDIP Figure 4. 16-Lead Wide-Body

Digital scales and other strain gage applications benefit from
the very low noise and low drift of the OPx13 family. Other
applications include use as a buffer or amplifier for both analog­to-digital (ADC) and digital-to-analog (DAC) sigma-delta
converters. Often these converters have high resolutions
requiring the lowest noise amplifier to utilize their full
potential. Many of these converters operate in either single­supply or low-supply voltage systems, and attaining the greater
signal swing possible increases system performance.

The OPx13 family is specified for single 5 V and dual ±15 V
o

peration over the XIND—extended industrial temperature
range (–40°C to +85°C). They are available in PDIP and SOIC
surface-mount packages.

8

7

6

5

NC

V+

OUT A

NULL

V+

8

OUT B

7

–IN B

6

+IN B

5

1

OUT A

OP213

2

–IN A

+IN A

00286-001

V–

TOP VIEW

3

(Not to Scale)

4

Figure 2. 8-Lead Narrow-Body

SOIC_N

1

OUT A

–IN A

2

+IN A

3

OP413

4

V+

TOP VIEW

(Not to Scale)

5

6

7

NC

8

NC = NO CONNECT

-

OUT B

+IN B

–IN B

SOIC_W

16

15

14

13

12

11

10

8

7

6

5

9

V+

OUT B

–IN B

+IN B

OUT D

–IN D

+IN D

V–

+IN C

–IN C

OUT C

NC

0286-002

00286-004

Rev. F

Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Anal og Devices for its use, nor for any infringements of patents or ot her
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] ©1993–2007 Analog Devices, Inc. All rights reserved.

OP113/OP213/OP413

www.BDTIC.com/ADI

TABLE OF CONTENTS

Features.............................................................................................. 1

Applications....................................................................................... 1

General Description......................................................................... 1

Pin Configurations........................................................................... 1

Revision History ...............................................................................2

Specifications..................................................................................... 3

Electrical Characteristics............................................................. 3

Absolute Maximum Ratings............................................................ 6

Thermal Resistance...................................................................... 6

ESD Caution.................................................................................. 6

Typical Performance Characteristics............................................. 7

Applications..................................................................................... 13

Phase Reversal............................................................................. 13

OP113 Offset Adjust .................................................................. 13

Application Circuits .......................................................................14

A High Precision Industrial Load-Cell Scale Amplifier........ 14

A Low Voltage, Single Supply Strain Gage Amplifier............ 14

A High Accuracy Linearized RTD Thermometer

Amplifier ..................................................................................... 14

A High Accuracy Thermocouple Amplifier........................... 15

An Ultralow Noise, Single Supply Instrumentation

Amplifier ..................................................................................... 15

Supply Splitter Circuit................................................................ 15

Low Noise Voltage Reference.................................................... 16

5 V Only Stereo DAC for Multimedia..................................... 16

Low Voltage Headphone Amplifiers........................................ 17

Low Noise Microphone Amplifier for Multimedia ............... 17

Precision Voltage Comparator.................................................. 17

Outline Dimensions....................................................................... 19

Ordering Guide .......................................................................... 20

REVISION HISTORY

3/07—Rev. E to Rev. F

Updated Format..................................................................Universal

Changes to Pin Configurations....................................................... 1

Changes to Absolute Maximum Ratings Section......................... 6

Deleted Spice Model....................................................................... 15

Updated Outline Dimensions....................................................... 19

Changes to Ordering Guide.......................................................... 20

8/02—Rev. D to Rev. E

Edits to Figure 6.............................................................................. 13

Edits to Figure 7.............................................................................. 13

Edits to OUTLINE DIMENSIONS.............................................. 16

9/01—Rev. C to Rev. E

Edits to ORDERING GUIDE.......................................................... 4

Rev. F | Page 2 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

SPECIFICATIONS

ELECTRICAL CHARACTERISTICS

@ VS = ±15.0 V, TA = 25°C, unless otherwise noted.

Table 1.

E Grade F Grade
Parameter Symbol Conditions Min Typ Max Min Typ Max Unit

INPUT CHARACTERISTICS

Offset Voltage VOS OP113 75 150 μV

−40°C ≤ TA ≤ +85°C 125 225 μV
OP213 100 250 μV

−40°C ≤ TA ≤ +85°C 150 325 μV
OP413 125 275 μV

−40°C ≤ TA ≤ +85°C 175 350 μV
Input Bias Current IB VCM = 0 V 240 600 600 nA

−40°C ≤ TA ≤ +85°C 700 700 nA
Input Offset Current IOS VCM = 0 V

−40°C ≤ TA ≤ +85°C 50 50 nA
Input Voltage Range VCM −15 +14 −15 +14 V
Common-Mode Rejection CMR −15 V ≤ VCM ≤ +14 V 100 116 96 dB

−15 V ≤ VCM ≤ +14 V,

−40°C ≤ TA ≤ +85°C 97 116 94 dB
Large-Signal Voltage Gain AVO OP113, OP213,
R

−40°C ≤ TA ≤ +85°C 1 2.4 1 V/μV
OP413, RL = 1 kΩ,

−40°C ≤ TA ≤ +85°C 1 2.4 1 V/μV
R

−40°C ≤ TA ≤ +85°C 2 8 2 V/μV
Long-Term Offset Voltage1 VOS 150 300 μV
Offset Voltage Drift2 ΔVOS/ΔT 0.2 0.8 1.5 μV/°C

OUTPUT CHARACTERISTICS

Output Voltage Swing High VOH RL = 2 kΩ 14 14 V
R

−40°C ≤ TA ≤ +85°C 13.9 13.9 V
Output Voltage Swing Low VOL RL = 2 kΩ −14.5 −14.5 V
R

−40°C ≤ TA ≤ +85°C −14.5 −14.5 V
Short-Circuit Limit ISC ±40 ±40 mA

POWER SUPPLY

Power Supply Rejection Ratio PSRR VS = ±2 V to ±18 V 103 120 100 dB
V

−40°C ≤ TA ≤ +85°C 100 120 97 dB
Supply Current/Amplifier ISY V
V

−40°C ≤ TA ≤ +85°C 3.8 3.8 mA
Supply Voltage Range VS 4 ±18 4 ±18 V

= 600 Ω,

L

= 2 kΩ,

L

= 2 kΩ,

L

= 2 kΩ,

L

= ±2 V to ±18 V

S

= 0 V, RL = ∞,

OUT

= ±18 V 3 3 mA

S

Rev. F | Page 3 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

E Grade F Grade
Parameter Symbol Conditions Min Typ Max Min Typ Max Unit

AUDIO PERFORMANCE

THD + Noise VIN = 3 V rms, RL = 2 kΩ,

f = 1 kHz 0.0009 0.0009 %

Voltage Noise Density en f = 10 Hz 9 9 nV/√Hz
f = 1 kHz 4.7 4.7 nV/√Hz

Current Noise Density in f = 1 kHz 0.4 0.4 pA/√Hz

Voltage Noise en p-p 0.1 Hz to 10 Hz 120 120 nV p-p
DYNAMIC PERFORMANCE

Slew Rate SR RL = 2 kΩ 0.8 1.2 0.8 1.2 V/μs

Gain Bandwidth Product GBP 3.4 3.4 MHz

Channel Separation V

R

Settling Time tS to 0.01%, 0 V to 10 V step 9 9 μs

1

Long-term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at 125°C, with an LTPD of 1.3.

2

Guaranteed specifications, based on characterization data.

@ VS = 5.0 V, TA = 25°C, unless otherwise noted.

Table 2.

E Grade F Grade
Parameter Symbol Conditions Min Typ Max Min Typ Max Unit

INPUT CHARACTERISTICS

Offset Voltage VOS OP113 125 175 μV

−40°C ≤ TA ≤ +85°C 175 250 μV

OP213 150 300 μV

−40°C ≤ TA ≤ +85°C 225 375 μV

OP413 175 325 μV

−40°C ≤ TA ≤ +85°C 250 400 μV

Input Bias Current IB VCM = 0 V, V

−40°C ≤ TA ≤ +85°C 750 750 nA

Input Offset Current IOS VCM = 0 V, V

−40°C ≤ TA ≤ +85°C 50 50 nA

Input Voltage Range VCM 0 4 4 V

Common-Mode Rejection CMR 0 V ≤ VCM ≤ 4 V 93 106 90 dB

0 V ≤ VCM ≤ 4 V,

−40°C ≤ TA ≤ +85°C 90 87 dB

Large-Signal Voltage Gain A

OP113, OP213,

VO

R

0.01 V ≤ V

OP413, RL = 600, 2 kΩ,

0.01 V ≤ V

Long-Term Offset Voltage1 V

200 350 μV

OS

Offset Voltage Drift2 ∆VOS/∆T 0.2 1.0 1.5 μV/°C

= 10 V p-p

OUT

= 2 kΩ, f = 1 kHz 105 105 dB

L

= 2 300 650 650 nA

OUT

= 2

OUT

= 600 Ω, 2 kΩ,

L

≤ 3.9 V 2 2 V/μV

OUT

≤ 3.9 V 1 1 V/μV

OUT

Rev. F | Page 4 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

E Grade F Grade
Parameter Symbol Conditions Min Typ Max Min Typ Max Unit

OUTPUT CHARACTERISTICS

Output Voltage Swing High VOH RL = 600 kΩ 4.0 4.0 V
R

−40°C ≤ TA ≤ +85°C 4.1 4.1 V
R

−40°C ≤ TA ≤ +85°C 3.9 3.9 V
Output Voltage Swing Low VOL RL = 600 Ω,

−40°C ≤ TA ≤ +85°C 8 8 mV
R

−40°C ≤ TA ≤ +85°C 8 8 mV
Short-Circuit Limit ISC ±30 ±30 mA

POWER SUPPLY

Supply Current ISY V
I

–40°C ≤ TA ≤ +85°C 3.0 3.0 mA

SY

AUDIO PERFORMANCE

THD + Noise V
Voltage Noise Density en f = 10 Hz 9 9 nV/√Hz
f = 1 kHz 4.7 4.7 nV/√Hz
Current Noise Density in f = 1 kHz 0.45 0.45 pA/√Hz
Voltage Noise en p-p 0.1 Hz to 10 Hz 120 120 nV p-p

DYNAMIC PERFORMANCE

Slew Rate SR RL = 2 kΩ 0.6 0.9 0.6 V/μs
Gain Bandwidth Product GBP 3.5 3.5 MHz
Settling Time tS to 0.01%, 2 V step 5.8 5.8 μs

1

Long-term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at 125°C, with an LTPD of 1.3.

2

Guaranteed specifications, based on characterization data.

= 100 kΩ,

L

= 600 Ω,

L

= 100 kΩ,

L

= 2.0 V, no load 1.6 2.7 2.7 mA

OUT

= 0 dBu, f = 1 kHz 0.001 0.001 %

OUT

Rev. F | Page 5 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

ABSOLUTE MAXIMUM RATINGS

Table 3.

Parameter Rating

Supply Voltage ±18 V
Input Voltage ±18 V
Differential Input Voltage ±10 V
Output Short-Circuit Duration to GND Indefinite
Storage Temperature Range −65°C to +150°C
Operating Temperature Range −40°C to +85°C
Junction Temperature Range −65°C to +150°C
Lead Temperature Range (Soldering, 60 sec) 300°C

Stresses above those listed under Absolute Maximum Ratings
ma

y cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.

THERMAL RESISTANCE

Table 4. Thermal Resistance

Package Type θJA θ

8-Lead PDIP (P) 103 43 °C/W
8-Lead SOIC_N (S) 158 43 °C/W
16-Lead SOIC_W (S) 92 27 °C/W

Unit

JC

ESD CAUTION

Rev. F | Page 6 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

TYPICAL PERFORMANCE CHARACTERISTICS

100

VS = ±15V
T

= 25°C

A

400 × OP AMPS
PLASTIC PACKAG E

80

150

120

VS = ±15V
–40°C ≤ T
400 × OP AMPS
PLASTIC PACKAG E

≤ +85°C

A

60

UNITS

40

20

0

–40

–50

INPUT OFFSET VOLTAGE, VOS (µV)

Figure 5. OP113 Input Offset (V

500

VS = ±15V

= 25°C

T

A

896 × OP AMPS
PLASTIC PACKAG E

400

300

UNITS

200

100

0

–80

–100

INPUT OFFSET VOLTAGE, VOS (µV)

Figure 6. OP213 Input Offset (V

500

VS = ±15V

= 25°C

T

A

1220 × OP AMPS
PLASTIC PACKAG E

400

) Distribution @ ±15 V

OS

) Distribution @ ±15 V

OS

90

UNITS

60

30

00286-005

403020100–10–20–30

50

00286-006

100

806040200–20–40–60

0

0.1

0

TCVOS (µV)

Figure 8. OP113 Temperature Drift (TCV

500

400

300

UNITS

200

100

0

0.1

0

TCVOS (µV)

Figure 9. OP213 Temperature Drift (TCV

600

500

) Distribution @ ±15 V

OS

VS = ±15V
–40°C ≤ T
896 × OP AMPS
PLASTIC PACKAG E

) Distribution @ ±15 V

OS

VS = ±15V
–40°C ≤ T
1220 × OP AMPS
PLASTIC PACKAG E

≤ +85°C

A

≤ +85°C

A

00286-008

1.0

0.90.80.70.60.50. 40.30.2

00286-009

1.0

0.90.80. 70.60.50.40.30.2

300

UNITS

200

100

0

–40

–60

INPUT OFFSET VOLTAGE, VOS (µV)

Figure 7. OP413 Input Offset (V

) Distribution @ ±15 V

OS

00286-007

140

120100806040200–20

Rev. F | Page 7 of 24

400

300

UNITS

200

100

0

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

Figure 10. OP413 Temperature Drift (TCV

TCV

(µV)

OS

) Distribution @ ±15 V

OS

00286-010

OP113/OP213/OP413

www.BDTIC.com/ADI

1000

500

800

600

= +5V

V

S

V

400

INPUT BIAS CURRENT (nA)

200

0

–75

–50

V

= ±15V

S

V

= 0V

CM

TEMPERATURE (° C)

CM

= +2.5V

Figure 11. OP113 Input Bias Current vs. Temperature

5.0

4.5

4.0

3.5

POSITIVE OUTPUT SWING (V)

3.0

+SWING

R

= 2kΩ

L

+SWING

R

= 600Ω

L

–50

–75 100

TEMPERATURE (°C)

–SWING

R

= 2kΩ

L

–SWING

R

VS = 5V

= 600Ω

L

7550250–25

Figure 12. Output Swing vs. Temperature and R

60

VS = ±15V

= 25°C

T

40

A

20

0

–20

–40

–60

–80

CHANNEL SEPARATIO N (dB)

–100

–120

10 100 1k 10k 100k 1M 10M

105

FREQUENCY (Hz)

Figure 13. Channel Separation

VCM = 0V

1007550250–25

@ 5 V

L

125

2.0

1.5

1.0

0.5

0

125

400

300

VS = ±15V

200

INPUT BIAS CURRENT (nA)

100

00286-011

0
–75

–50

TEMPERATURE (°C)

VS = +5V

00286-014

125

1007550250–25

Figure 14. OP213 Input Bias Current vs. Temperature

15.0
V

= ±15V

S

14.5

14.0

13.5

13.0

12.5

–13.5

POSITIVE OUTPUT SWING (V)

NEGATIVE OUTPUT SWING (mV)

00286-012

–14.0

–14.5

–15.0

–75

–50

–SWING
R

= 600Ω

L

Figure 15. Output Swing v

20

18

16

14

12

10

8

6

OPEN-LOOP GAIN (V/µV)

4

2

00286-013

0

–75

–50

+SWING
R

= 2kΩ

L

+SWING

R

= 600Ω

L

TEMPERATURE (° C)

s. Temperature and R

RL = 2kΩ

RL = 600Ω

TEMPERATURE (° C)

–SWING
R

= 2kΩ

L

L

VS = 5V
V

= 3.9V

O

1007550250–25

@ ±15 V

1007550250–25

125

125

00286-015

00286-016

Figure 16. Open-Loop Gain vs. Temperature @ 5 V

Rev. F | Page 8 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

12.5

RL = 2kΩ

10.0

7.5

5.0

OPEN-LOOP GAIN (V/µV)

2.5

0
–75

RL = 1kΩ

RL = 600Ω

TEMPERATURE (° C)

Figure 17. OP413 Open-Loop Gain vs. Temperature

100

V+ = 5V
V– = 0V
T

= 25°C

A

80

VS = ±15V
V

= ±10V

D

1007550250–25

00286-017

125–50

0

10

9

8

–50

RL = 2kΩ

RL = 600Ω

TEMPERATURE (° C)

7

6

5

4

3

OPEN-LOOP GAIN (V/µV)

2

1

0

–75

Figure 20. OP213 Open-Loop Gain vs. Temperature

100

TA = 25°C

= ±15V

V

S

80

VS = ±15V
V

= ±10V

O

1007550250–25

125

00286-020

0

60

40

PHASE

20

OPEN-LOOP GAIN (dB)

0

–20

1k 10k 100k 1M 10M

GAIN

θm = 57°

FREQUENCY (Hz)

Figure 18. Open-Loop Gain, Phase vs. Frequency @ 5 V

50

40

AV = 100

30

20

AV = 10

10

0

CLOSED-LOOP GAIN (dB)

AV = 1

–10

–20

1k 10k 100k 1M 10M

FREQUENCY (Hz)

Figure 19. Closed-Loop Gain vs. Frequency @ 5 V

V+ = 5V
V– = 0V
T

= 25°C

A

45

90

135

180

225

60

40

PHASE

PHASE (Degrees)

00286-018

20

OPEN-LOOP GAIN (dB)

0

–20

1k 10k 100k 1M 10M

Figure 21. Open-Loop Gain, Ph

50

40

AV = 100

30

20

AV = 10

10

0

CLOSED-LOOP GAIN (dB)

AV = 1

–10

00286-019

–20

1k 10k 100k 1M 10M

GAIN

θm = 72°

FREQUENCY (Hz)

ase vs. Frequency @ ±15 V

FREQUENCY (Hz)

TA = 25°C

= ±15V

V

S

45

90

135

180

225

PHASE (Degrees)

00286-021

00286-052

Figure 22. Closed-Loop Gain vs. Frequency @ ±15 V

Rev. F | Page 9 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

70

V+ = 5V
V– = 0V

65

GBW

60

θm

PHASE MARGIN (Degrees)

55

50

–75

–50

TEMPERATURE (° C)

7550250–25

100

125

5

4

3

2

GAIN BANDWIDT H PRODUCT (MHz)

1

0286-022

Figure 23. Gain Bandwidth Product and Phase Margin vs. Temperature @ 5 V

30

25

20

15

TA = 25°C

= ±15V

V

S

70

VS = ±15V

65

60

55

PHASE MARGIN (Degrees)

50

–50

–75

GBW

θm

TEMPERATURE (°C)

7550250–25

100

125

5

4

3

2

GAIN BANDWIDT H PRODUCT (MHz)

1

00286-025

Figu re 26. Gain B andwid th Pro duct and Phase Margin vs. Temperature @ ±15 V

3.0

2.5

2.0

1.5

TA = 25°C
V

= ±15V

S

10

5

VOLTAGE NOISE DENSI TY (nV/ Hz)

0

1 10 100 1k

FREQUENCY (Hz)

Figure 24. Voltage Noise Density vs. Frequency

140

120

100

80

60

40

COMMON-MO DE REJECTIO N (dB)

20

0

100 1k 10k 100k 1M

FREQUENCY (Hz)

V+ = 5V
V– = 0V
T

Figure 25. Common-Mode Rejection vs. Frequency @ 5 V

= 25°C

A

1.0

0.5

CURRENT NOISE DENS ITY (pA/ Hz)

00286-023

0

1 10 100 1k

FREQUENCY (Hz)

00286-026

Figure 27. Current Noise Density vs. Frequency

140

120

100

80

60

40

COMMON-MO DE REJECTIO N (dB)

20

00286-024

0

FREQUENCY (Hz)

Figure 28. Common-Mode Rejectio

n vs. Frequency @ ±15 V

TA = 25°C
V

= ±15V

S

00286-027

1M1k 100k10k100

Rev. F | Page 10 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

140

120

100

80

60

40

POWER SUPPLY REJECTION (dB)

20

0

–PSRR

Figure 29. Power Supply Rejecti

6

5

4

3

2

FREQUENCY (Hz)

on vs. Frequency @ ±15 V

+PSRR

TA = 25°C
V

= ±15V

S

VS = 5V
R

= 2kΩ

L

T

= 25°C

A

A

= 1

VCL

40

30

20

IMPEDANCE (Ω)

10

00286-028

1M1k 100k10k100

0

Figure 32. Closed-Loop Output I

30

25

20

15

10

AV = 100

AV = 10

FREQUENCY (Hz)

mpedance vs. Frequency @ ±15 V

TA = 25°C
V

= ±15V

S

AV = 1

VS = ±15V

= 2kΩ

R

L

= 25°C

T

A

= 1

A

VOL

00286-031

1M1k 100k10k100

MAXIMUM OUTPUT SWING (V)

1

0

1k 10k 100k 1M 10M

FREQUENCY (Hz)

Figure 30. Maximum Output Swing vs. Frequency @ 5 V

50

VS = 5V

45

R

= 2kΩ

L

V

= 100mV p-p

IN

40

T

= 25°C

A

A

= 1

VCL

35

30

25

20

OVERSHOOT (%)

15

10

5

0

0

100

NEGATIVE
EDGE

POSITIVE
EDGE

LOAD CAPACITANCE (pF)

400300200

Figure 31. Small-Signal Overshoot vs. Load Capacitance @ 5 V

500

MAXIMUM OUTPUT SWING (V)

5

00286-029

0

1k 10k 100k 1M 10M

FREQUENCY (Hz)

00286-032

Figure 33. Maximum Output Swing vs. Frequency @ ±15 V

20

VS = ±15V

18

= 2kΩ

R

L

V

= 100mV p-p

IN

16

= 25°C

T

A

= 1

A

VCL

14

12

10

8

OVERSHOOT (%)

6

4

2

00286-030

0

0

100

LOAD CAPACITANCE ( pF)

POSITIVE
EDGE

NEGATIVE
EDGE

400300200

500

00286-033

Figure 34. Small-Signal Overshoot vs. Load Capacitance @ ±15 V

Rev. F | Page 11 of 24

OP113/OP213/OP413

Ω

www.BDTIC.com/ADI

2.0
VS = 5V

0.5V ≤ V

OUT

≤ 4.0V

2.0
VS = ±15V
–10V ≤ V

OUT

≤ +10V

+SLEW RATE

1.5

+SLEW RATE

1.0

SLEW RATE (V/µs)

0.5

0

–75

–50

TEMPERATURE ( °C)

–SLEW RATE

7550250–25

Figure 35. Slew Rate vs. Temperature @ 5 V (0.5 V ≤ V

100

90

10

0%

20mV

1s

Figure 36. Input Voltage Noise @ ±15 V (20 nV/div)

100

≤ 4.0 V)

OUT

125

00286-035

1.5

1.0

SLEW RATE (V/µs)

0.5

00286-034

0

–75 100

–50

TEMPERATURE (° C)

Figure 38. Slew Rate vs. Temperature @ ±15 V (–10 V ≤ V

100

90

10

0%

20mV

–SLEW RATE

7550250–25

OUT

1s

00286-037

125

≤ +10.0 V)

00286-038

Figure 39. Input Voltage Noise @ 5 V (20 nV/div)

5

4

100Ω

909

0.1Hz TO 10Hz
= 1000

A

V

Figure 37. Noise Test Diagram

A

= 100

V

t

OUT

VS = ±18V

3

2

SUPPLY CURRENT (mA)

00286-036

1

0

–75

–50

TEMPERATURE ( °C)

Figure 40. Supply Current vs. Temperature

VS = ±15V

VS = +5V

00286-039

125

1007550250–25

Rev. F | Page 12 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

APPLICATIONS

The OP113, OP213, and OP413 form a new family of high
performance amplifiers that feature precision performance in
standard dual-supply configurations and, more importantly,
maintain precision performance when a single power supply is
used. In addition to accurate dc specifications, it is the lowest
noise single-supply amplifier available with only 4.7 nV/√Hz
typical noise density.

Single-supply applications have special requirements due to the

erally reduced dynamic range of the output signal. Single-

gen
supply applications are often operated at voltages of 5 V or 12 V,
compared to dual-supply applications with supplies of ±12 V or
±15 V. This results in reduced output swings. Where a dual­supply application may often have 20 V of signal output swing,
single-supply applications are limited to, at most, the supply
range and, more commonly, several volts below the supply.
In order to attain the greatest swing, the single-supply output
stage must swing closer to the supply rails than in dual-supply
applications.

The OPx13 family has a new patented output stage that allows
th

e output to swing closer to ground, or the negative supply,
than previous bipolar output stages. Previous op amps had
outputs that could swing to within about 10 mV of the negative
supply in single-supply applications. However, the OPx13
family combines both a bipolar and a CMOS device in the output
stage, enabling it to swing to within a few hundred µV of ground.

When operating with reduced supply voltages, the input range

lso reduced. This reduction in signal range results in

is a
reduced signal-to-noise ratio for any given amplifier. There are
only two ways to improve this: increase the signal range or
reduce the noise. The OPx13 family addresses both of these
parameters. Input signal range is from the negative supply to
within 1 V of the positive supply over the full supply range.
Competitive parts have input ranges that are 0.5 V to 5 V less
than this. Noise has also been optimized in the OPx13 family.
At 4.7 nV/√Hz, the noise is less than one fourth that of competitive
devices.

PHASE REVERSAL

The OPx13 family is protected against phase reversal as long as
both of the inputs are within the supply ranges. However, if
there is a possibility of either input going below the negative
supply (or ground in the single-supply case), the inputs should
be protected with a series resistor to limit input current to 2 mA.

OP113 OFFSET ADJUST

The OP113 has the facility for external offset adjustment, using
the industry standard arrangement. Pin 1 and Pin 5 are used in
conjunction with a potentiometer of 10 k total resistance,
connected with the wiper to V− (or ground in single-supply
applications). The total adjustment range is about ±2 mV using
this configuration.

Adjusting the offset to 0 has minimal effect on offset drift
(

assuming the potentiometer has a tempco of less than
1000 ppm/°C). Adjustment away from 0, however, (as with all
bipolar amplifiers) results in a TCV

3.3 V/°C for every millivolt of induced offset.
It is, therefore, not generally recommended that this trim be

us

ed to compensate for system errors originating outside of the
OP113. The initial offset of the OP113 is low enough that
external trimming is almost never required, but if necessary, the
2 mV trim range may be somewhat excessive. Reducing the
trimming potentiometer to a 2 k value results in a more
reasonable range of ±400 V.

of approximately

OS

Rev. F | Page 13 of 24

OP113/OP213/OP413

V

V

www.BDTIC.com/ADI

APPLICATION CIRCUITS

A HIGH PRECISION INDUSTRIAL LOAD-CELL SCALE AMPLIFIER

The OPx13 family makes an excellent amplifier for
conditioning a load-cell bridge. Its low noise greatly improves
the signal resolution, allowing the load cell to operate with a
smaller output range, thus reducing its nonlinearity. Figure 41
s

hows one half of the OPx13 family used to generate a very
stable 10 V bridge excitation voltage while the second amplifier
provides a differential gain. R4 should be trimmed for
maximum common-mode rejection.

+15

2

1

3

AD588BQ

9

CMRR TRIM
10-TURN
T.C. LE SS THAN 50pp m/°C

OUTPUT
010V
FS

2N2219A

350Ω
LOAD
CELL

R5

1kΩ

OP213

1

+10V

100mV
F.S.

1/2

8

A2

3

+

–

2

R3

17.2kΩ

0.1%

–

6

+

5

R1

17.2kΩ

0.1%

A1

–15V

+10V

4

R4

500Ω

7

1/2

OP213

R2

301Ω

0.1%

Figure 41. Precision Load-Cell Scale Amplifier

A LOW VOLTAGE, SINGLE SUPPLY STRAIN GAGE AMPLIFIER

The true zero swing capability of the OPx13 family allows the
amplifier in Figure 42 to amplify the strain gage bridge
a

ccurately even with no signal input while being powered by a
single 5 V supply. A stable 4 V bridge voltage is made possible
by the rail-to-rail OP295 amplifier, whose output can swing to
within a millivolt of either rail. This high voltage swing greatly
increases the bridge output signal without a corresponding
increase in bridge input.

–15V

16

14

15

8

10

136 711 124

+

10µF

00286-040

5

2

IN

6

OUT

REF43

GND

4

5V

5

+

OP295

–

6

8

1/2

4

100kΩ

OUTPUT
0V 3.5V

7

R4

00286-041

350Ω

35mV

FS

2N2222A

4V

3

2

R1
100kΩ

1

12kΩ

+

1/2

OP213

–

8

1/2

OP295

4

R8

1

R2

20kΩ

R5

2.1kΩ

RG = 2127.4Ω

2.5V

3

+

–

2

R7

20kΩ

R3

20kΩ

R6

27.4Ω

Figure 42. Single Supply Strain Gage Amplifier

A HIGH ACCURACY LINEARIZED RTD THERMOMETER AMPLIFIER

Zero suppressing the bridge facilitates simple linearization of
the resistor temperature device (RTD) by feeding back a small
amount of the output signal to the RTD. In Figure 43, the left
leg o

f the bridge is servoed to a virtual ground voltage by
Amplifier A1, and the right leg of the bridge is servoed to 0 V
by Amplifier A2. This eliminates any error resulting from
common-mode voltage change in the amplifier. A 3-wire RTD
is used to balance the wire resistance on both legs of the bridge,
thereby reducing temperature mismatch errors. The 5 V bridge
excitation is derived from the extremely stable AD588 reference
device with 1.5 ppm/°C drift performance.

Linearization of the RTD is done by feeding a fraction of the

utput voltage back to the RTD in the form of a current. With

o
just the right amount of positive feedback, the amplifier output
will be linearly proportional to the temperature of the RTD.

Rev. F | Page 14 of 24

OP113/OP213/OP413

V

–15V

F

V

www.BDTIC.com/ADI

10µ

100Ω

RTD

16 2

11

12

13

AD588BQ

4

6

7 9 8 10

+

+15

14

15

1

R3

50Ω

3

R1

8.25kΩ

R

W1

R

W2

R

W3

2

3

R2

8.25kΩ

R4
100Ω

–

A1

+

OP213

1/2

R

G

1

FULL SCALE ADJUST

R5

4.02kΩR7100Ω

+15V

8

–

6

A2

7

+

5

–15V

4

OP213

R8

49.9kΩ

1/2

V

OUT

–1.5V = –150°C
+5V = +500°C

R9
5kΩ
LINEARITY
ADJUST
@1/2 FS

(10mV/°C)

Figure 43. Ultraprecision RTD Amplifier

To calibrate the circuit, first immerse the RTD in a 0°C ice bath
or substitute an exact 100  resistor in place of the RTD. Adjust
the zero adjust potentiometer for a 0 V output, and then set R9,
linearity adjust potentiometer, to the middle of its adjustment
range. Substitute a 280.9  resistor (equivalent to 500°C) in
place of the RTD, and adjust the full-scale adjust potentiometer
for a full-scale voltage of 5 V.

To calibrate out the nonlinearity, substitute a 194.07  resistor

uivalent to 250°C) in place of the RTD, and then adjust the

(eq
linearity adjust potentiometer for a 2.5 V output. Check and
readjust the full-scale and half-scale as needed.

Once calibrated, the amplifier outputs a 10 mV/°C temperature
c

oefficient with an accuracy better than ±0.5°C over an RTD
measurement range of −150°C to +500°C. Indeed the amplifier
can be calibrated to a higher temperature range, up to 850°C.

A HIGH ACCURACY THERMOCOUPLE AMPLIFIER

Figure 44 shows a popular K-type thermocouple amplifier with
cold-junction compensation. Operating from a single 12 V
supply, the OPx13 family’s low noise allows temperature
measurement to better than 0.02°C resolution over a 0°C to
1000°C range. The cold-junction error is corrected by using an
inexpensive silicon diode as a temperature measuring device.
It should be placed as close to the two terminating junctions as
physically possible. An aluminum block might serve well as an
isothermal system.

1N4148

D1

R4

5V

R1

10.7kΩ

R2

2.74kΩ

200Ω

R3

53.6Ω

R9

124kΩ

R5

40.2kΩ

R8

453Ω

R6

–

2

OP213

+

3

12V

0.1µF

8

1/2

4

10µF
+

+

1

0V TO 10V
(0°C TO 1000°C)

00286-043

12V

0.1µF

K-TYPE

THERMOCO UPLE

40.7µV/°C

REF02EZ

2 6

+

4

––

++

5.62kΩ

Figure 44. Accurate K-Type Thermocouple Amplifier

R6 should be adjusted for a 0 V output with the thermocouple
measuring tip immersed in a 0°C ice bath. When calibrating, be
sure to adjust R6 initially to cause the output to swing in the
positive direction first. Then back off in the negative direction
until the output just stops changing.

00286-042

AN ULTRALOW NOISE, SINGLE SUPPLY INSTRUMENTATION AMPLIFIER

Extremely low noise instrumentation amplifiers can be built
using the OPx13 family. Such an amplifier that operates from a
single supply is shown in Figure 45. Resistors R1 to R5 should
b

e of high precision and low drift type to maximize CMRR
performance. Although the two inputs are capable of operating
to 0 V, the gain of −100 configuration limits the amplifier input
common-mode voltage to 0.33 V.

5V TO 36

+

V

IN

–

*R1

10kΩ

*ALL RESISTORS ±0.1%, ±25ppm/°C.

+

1/2

OP213

–

*R2

10kΩ

*R

(200Ω + 12.7Ω)

10kΩ

+

1/2

OP213

–

*R3

G

*R4

10kΩ

GAIN = + 6

20kΩ

R

V

OUT

G

00286-044

Figure 45. Ultralow Noise, Single Supply Instrumentation Amplifier

SUPPLY SPLITTER CIRCUIT

The OPx13 family has excellent frequency response
characteristics that make it an ideal pseudoground reference
generator, as shown in Figure 46. The OPx13 family serves as a
v

oltage follower buffer. In addition, it drives a large capacitor
that serves as a charge reservoir to minimize transient load
changes, as well as a low impedance output device at high
frequencies. The circuit easily supplies 25 mA load current with
good settling characteristics.

Rev. F | Page 15 of 24

OP113/OP213/OP413

V

V

5

5

V

www.BDTIC.com/ADI

R1
kΩ

R2
kΩ

+ = 5V 12

S

2

–

OP213

3

+

1/2

R3

2.5kΩ

C1

0.1µF

8

1

4

R4

100Ω

+

V

S

+

C2
1µF

OUTPUT

2

Figure 46. False Ground Generator

LOW NOISE VOLTAGE REFERENCE

Few reference devices combine low noise and high output drive
capabilities. Figure 47 shows the OPx13 family used as a two-

le active filter that band limits the noise of the 2.5 V reference.

po
Total noise measures 3 V p-p.

5

SUPPLY

1

2

3

4

5

6

7

8

V

L

LL

DL

CK

DR

LR

DGND

V

R

B

18-BIT

DAC

18-BIT

SERIAL

REG.

18-BIT

SERIAL

REG.

18-BIT

DAC

AD1868

V

V

L

V

B

16

–

15

REF

REF

+

+
–

V

AGND

VOR

O

V

7.68kΩ

14

L

330pF

13

12

11

10

7.68kΩ

9

S

330pF

Figure 48. 5 V Only 18-Bit Stereo DAC

5V

5V

2

IN

OUT

REF43

GND

4

–

10µF

+

6

10kΩ10kΩ

+

C2
10µF

2

3

8

–

1/2

OP213

+

4

1

3µV p-p NOISE

OUTPUT

2.5V

00286-046

Figure 47. Low Noise Voltage Reference

0286-045

5 V ONLY STEREO DAC FOR MULTIMEDIA

The OPx13 family’s low noise and single supply capability are
ideally suited for stereo DAC audio reproduction or sound
synthesis applications such as multimedia systems. Figure 48
s

hows an 18-bit stereo DAC output setup that is powered from a
single 5 V supply. The low noise preserves the 18-bit dynamic
range of the AD1868. For DACs that operate on dual supplies,
the OPx13 family can also be powered from the same supplies.

8

3

+

+

9.76kΩ

9.76kΩ

+

OP213

2

–

7.68kΩ

7.68kΩ

6

–

OP213

5

+

1/2

4

1/2

100pF

100pF

220µF

1

+

220µF

7

+

LEFT
CHANNEL

–

OUTPUT

47kΩ

RIGHT
CHANNEL

–

OUTPUT

47kΩ

0286-047

Rev. F | Page 16 of 24

OP113/OP213/OP413

Ω

C

R

www.BDTIC.com/ADI

LOW VOLTAGE HEADPHONE AMPLIFIERS

Figure 49 shows a stereo headphone output amplifier for the
AD1849 16-bit SOUNDPORT® stereo codec device.
pseudo-reference voltage is derived from the common-mode
voltage generated internally by the AD1849, thus providing a
convenient bias for the headphone output amplifiers.

OPTIONAL

GAIN

1kΩ

V

REF

10µF

31

LOUT1L

AD1849

CMOUT

LOUT1R

V

19

29

REF

10µF

10kΩ

10kΩ

L VOLUME
CONTROL

R VOLUME
CONTROL

1kΩ

Figure 49. Headphone Output Amplif

V

REF

5kΩ

5V

–

1/2

OP213

+

5V

1/2

OP213

–

1/2

OP213

+

5kΩ

OPTIO NAL
GAIN

16Ω

–

+

16Ω

ier for Multimedia Sound Codec

220µF

+

47kΩ

220µF

+

47kΩ

1

The

HEADPHONE
LEFT

HEADPHONE
RIGHT

LOW NOISE MICROPHONE AMPLIFIER FOR MULTIMEDIA

The OPx13 family is ideally suited as a low noise microphone
preamp for low voltage audio applications. Figure 50 shows a

in of 100 stereo preamp for the AD1849 16-bit SOUNDPORT

ga
stereo codec chip. The common-mode output buffer serves as a
phantom power driver for the microphones.

10k

5V

–

LEFT

ELECTRET

ONDENSE

MIC

INPUT

RIGHT

ELECTRET

CONDENSER

MIC

INPUT

20Ω

20Ω

10µF

10µF

+

5V

1/2

OP213

+

50Ω

50Ω

–

+

10kΩ

100Ω

+

OP213

–

OP213

+

100Ω10kΩ

1/2

10kΩ

1/2

17

MINL

AD1849

19

CMOUT

15

MINR

00286-049

Figure 50. Low Noise Stereo Microphone Amplifier for Multimedia Sound

Codec

PRECISION VOLTAGE COMPARATOR

With its PNP inputs and 0 V common-mode capability, the
OPx13 family can make useful voltage comparators. There is
only a slight penalty in speed in comparison to IC comparators.
However, the significant advantage is its voltage accuracy. For
example, V
with CMRR and PSRR exceeding 100 dB, while operating from

00286-048

a 5 V supply. Standard comparators like the 111/311 family
operate on 5 V, but not with common mode at ground, nor with
offset below 3 mV. Indeed, no commercially available single­supply comparator has a V

1

SOUNDPORT is a registered trademark of Analog Devices, Inc.

can be a few hundred microvolts or less, combined

OS

less than 200 V.

OS

Rev. F | Page 17 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

Figure 51 shows the OPx13 family response to a 10 mV
overdrive signal when operating in open loop. The top trace
shows the output rising edge has a 15 s propagation delay,
whereas the bottom trace shows a 7 s delay on the output
falling edge. This ac response is quite acceptable in many
applications.

±10mV OVERDRI VE

+2.5V

0V

–2.5V

t

t

=

= 5ms

r

f

25kΩ

100Ω

5V

+

1/2

OP113

–

The low noise and 250 V (maximum) offset voltage enhance
the overall dc accuracy of this type of comparator. Note that zero­crossing detectors and similar ground referred comparisons can be
implemented even if the input swings to −0.3 V below ground.

+IN

9V

9V

–IN

OUT

5µs

00286-051

100

2V

90

Figure 52. OP213 Simplified Schematic

10

0%

2V

0286-050

Figure 51. Precision Comparator

Rev. F | Page 18 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

OUTLINE DIMENSIONS

0.400 (10.16)

0.365 (9.27)

0.355 (9.02)

0.210 (5.33)
MAX

0.150 (3.81)

0.130 (3.30)

0.115 (2.92)

0.022 (0.56)

0.018 (0.46)

0.014 (0.36)

8

1

0.100 (2.54)

0.070 (1.78)

0.060 (1.52)

0.045 (1.14)

BSC

5

4

0.280 (7.11)

0.250 (6.35)

0.240 (6.10)

0.015
(0.38)
MIN

SEATING
PLANE

0.005 (0.13)
MIN

0.060 (1.52)
MAX

0.015 (0.38)
GAUGE

PLANE

0.325 (8.26)

0.310 (7.87)

0.300 (7.62)

0.430 (10.92)
MAX

0.195 (4.95)

0.130 (3.30)

0.115 (2.92)

0.014 (0.36)

0.010 (0.25)

0.008 (0.20)

CONTROLL ING DIMENSIONS ARE IN INCHES; MILLIM ETER DIMENSI ONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ON LY AND ARE NO T APPROPRIATE FO R USE IN DESIG N.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF L EADS .

COMPLIANT TO JEDEC STANDARDS MS-001

070606-A

Figure 53. 8-Lead Plastic Dual In-Line Package [PDIP]

Narrow Body

P-Suffix

(N-8)

Dimensions shown in inches and (millimeters)

5.00 (0.1968)

4.80 (0.1890)

4.00 (0.1574)

3.80 (0.1497)

0.25 (0.0098)

0.10 (0.0040)

COPLANARITY

0.10

CONTROLL ING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSI ONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ON LY AND ARE NO T APPROPRIATE FOR USE IN DESIGN.

85

1

1.27 (0.0500)

SEATING

PLANE

COMPLIANT TO JEDEC STANDARDS MS-012-A A

BSC

6.20 (0.2441)

5.80 (0.2284)

4

1.75 (0.0688)

1.35 (0.0532)

0.51 (0.0201)

0.31 (0.0122)

8°
0°

0.25 (0.0098)

0.17 (0.0067)

0.50 (0.0196)

0.25 (0.0099)

1.27 (0.0500)

0.40 (0.0157)

45°

012407-A

Figure 54. 8-Lead Standard Small Outline Package [SOIC_N]

Narrow Body

S-Suffix

(R-8)

Dimensions shown in millimeters and (inches)

Rev. F | Page 19 of 24

OP113/OP213/OP413

C

www.BDTIC.com/ADI

0.30 (0.0 118)

0.10 (0.0039)

OPLANARITY

0.10

10.50 (0.4134)

10.10 (0.3976)

BSC

9

7.60 (0.2992)

7.40 (0.2913)

8

10.65 (0.4193)

10.00 (0.3937)

2.65 (0.1043)

2.35 (0.0925)

SEATING
PLANE

8°
0°

0.33 (0.0130)

0.20 (0.0079)

5

0

.

7

5

(0

0

.2

16

1

1.27 (0.0500)

0.51 (0.0201)

0.31 (0.0122)

CONTROLL ING DIMENSIONS ARE IN MIL L IMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MIL L IMETER EQ UIVALENTS FOR
REFERENCE ON LY AND ARE NO T APPROPRIATE FOR USE IN DESIGN.

COMPLIANT TO JEDEC STANDARDS MS-013-AA

(

0

.

0

2

9

0

0

9

.

1.27 (0.0500)

0.40 (0.0157)

5

)

45°

8

)

030707-B

Figure 55. 16-Lead Standard Small Outline Package [SOIC_W]

Wide Body

S-Suffix
(RW-16)

Dimensions shown in millimeters and (inches)

ORDERING GUIDE

Model Temperature Range Package Description Package Options

OP113ES −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113ES-REEL −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113ES-REEL7 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113ESZ1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113ESZ-REEL1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113ESZ-REEL71 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FS −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FS-REEL −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FS-REEL7 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FSZ1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FSZ-REEL1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP113FSZ-REEL71 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213ES −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)

OP213ES-REEL −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213ES-REEL7 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213ESZ1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213ESZ-REEL1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213ESZ-REEL71 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FP −40°C to +85°C 8-Lead PDIP N-8 (P-Suffix)
OP213FPZ1 −40°C to +85°C 8-Lead PDIP N-8 (P-Suffix)
OP213FS −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FS-REEL −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FS-REEL7 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FSZ1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FSZ-REEL1 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)
OP213FSZ-REEL71 −40°C to +85°C 8-Lead SOIC_N R-8 (S-Suffix)

Rev. F | Page 20 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

Model Temperature Range Package Description Package Options

OP413ES −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413ES-REEL −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413ESZ1 −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413ESZ-REEL1 −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413FS −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413FS-REEL −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413FSZ1 −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)
OP413FSZ-REEL1 −40°C to +85°C 16-Lead Wide Body SOIC_W RW-16 (S-Suffix)

1

Z = RoHS Compliant Part.

Rev. F | Page 21 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

NOTES

Rev. F | Page 22 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

NOTES

Rev. F | Page 23 of 24

OP113/OP213/OP413

www.BDTIC.com/ADI

NOTES

©1993–2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C00286-0-3/07(F)

Rev. F | Page 24 of 24