Page 1
74F06, 74F06A, 74F07, 74F07A
Inverter/buffer drivers
Product specification
IC15 Data Handbook
1992 Jul 24
INTEGRATED CIRCUITS
Page 2
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
2
July 24, 1992 853–1 122 07270
FEATURES OF 74F06, 74F07
•Open Collector output drive 64mA
•High speed
•12V output termination voltage
•Symmetrical propagation delays
FEATURES OF 74F06A, 74F07A
•Open Collector output drive 48mA
•High speed
•30V output termination voltage
•Replaces 74F06 and 74F07
•Improved performance upgrade for 74F06 and 74F07
•Reduced I
OH
leakage @ 30V
TYPE
TYPICAL
PROPAGATION
DELA Y
TYPICAL SUPPL Y
CURRENT
(TOT AL)
74F06 3.5ns 30mA
74F06A 9.0ns 30mA
74F07 4.5ns 32mA
74F07A 10.0ns 32mA
ORDERING INFORMATION
DESCRIPTION
COMMERCIAL RANGE
VCC = 5V ±10%,
T
amb
= 0°C to +70°C
PKG DWG #
14-pin plastic Dual In-line Package N74F06N, N74F06AN SOT27–1
14-pin plastic Small Outline N74F07D, N74F07AD SOT108–1
PIN CONFIGURATIONS
14
13
12
11
10
9
87
6
5
4
3
2
1
GND
V
CC
Y4
A3
Y3
A4
A5
Y
5
A0
Y0
Y
2
A1
Y
1
A2
SF00016
74F06/74F06A
14
13
12
11
10
9
87
6
5
4
3
2
1
GND
V
CC
Y4
A3
Y3
A4
A5
Y5
A0
Y0
Y2
A1
Y1
A2
SF00017
74F07/74F07A
LOGIC SYMBOLS
46810
135 91113
VCC = Pin 14
GND = Pin 7
SF00018
A0 A1 A2 A3 A4 A5
2
Y0Y1Y2Y3Y4Y5
12
74F06/74F06A
46810
135 91113
V
CC
= Pin 14
GND = Pin 7
SF00019
A0 A1 A2 A3 A4 A5
2
Y0 Y1 Y2 Y3 Y4 Y5
12
74F07/74F07A
Page 3
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
July 24, 1992
3
IEC/IEEE SYMBOLS
13
SF00020
12
11
10
9
8
5
6
3
4
1
2
74F06/74F06A
13
SF00021
12
11
10
9
8
5
6
3
4
1
2
74F07/74F07A
LOGIC DIAGRAMS
VCC = Pin 14
GND = Pin 7
SF00022
2
4
6
8
10
12
Y
0
Y
1
Y
2
Y
3
Y
4
Y
5
1
3
5
9
11
13
A0
A1
A2
A3
A4
A5
74F06/74F06A
VCC = Pin 14
GND = Pin 7
SF00023
2
4
6
8
10
12
Y0
Y1
Y2
Y3
Y4
Y5
1
3
5
9
11
13
A0
A1
A2
A3
A4
A5
74F07/74F07A
INPUT AND OUTPUT LOADING AND FAN OUT TABLE
PINS DESCRIPTION
74F (U.L.)
HIGH/LOW
LOAD VALUE
HIGH/LOW
An Data inputs (’F06, ’F07) 1.0/1.0 20µA/0.6mA
An Data inputs (’F06A, ’F07A) 1.0/0.7 20µA/0.4mA
Yn Data outputs (’F06) OC/106.7 OC/64mA
Yn Data outputs (’F06A) OC/80 OC/48mA
Yn Data outputs (’F07) OC/106.7 OC/64mA
Yn Data outputs (’F07A) OC/80 OC/48mA
NOTES:
1. One (1.0) FAST unit load is defined as: 20µA in the High state and 0.6mA in the Low state.
2. OC = Open Collector
FUNCTION TABLE
INPUTS OUTPUTS
’F06, ’F06A ’F07, ’F07A
An Yn Yn
L H L
H L H
NOTES:
1. H = High voltage level
2. L = Low voltage level
Page 4
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
July 24, 1992
4
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free air temperature range.)
SYMBOL
PARAMETER RATING UNIT
V
CC
Supply voltage –0.5 to +7.0 V
V
IN
Input voltage –0.5 to +7.0 V
I
IN
Input current –30 to +5 mA
V
OUT
Voltage applied to output in High output state ’F06, ’F07 –0.5 to 12 V
’F06A, ’F07A –0.5 to 30 V
I
OUT
Current applied to output in Low output state ’F06, ’F07 128 mA
’F06A, ’F07A 96 mA
T
amb
Operating free air temperature range 0 to +70 °C
T
stg
Storage temperature range –65 to +150 °C
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
LIMITS UNIT
MIN NOM MAX
V
CC
Supply voltage 4.5 5.0 5.5 V
V
IH
High-level input voltage 2.0 V
V
IL
Low-level input voltage 0.8 V
I
Ik
Input clamp current –18 mA
V
OH
High-level output voltage
’F06, ’F07 12 V
’F06A, ’F07A 30 V
I
OL
Low-level output current
’F06, ’F07 64 mA
’F06A, ’F07A 48 mA
T
amb
Operating free air temperature range 0 +70 °C
Page 5
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
July 24, 1992
5
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
PARAMETER TEST CONDITIONS
1
LIMITS UNIT
MIN TYP
2
MAX
I
OH
High-level output
’F06, ’F07 VCC = MIN, VIL = MAX,
250 µA
curren
t
’F06A, ’F07A
V
OH
=
MAX, V
IH
=
MIN
100 µA
V
OL
Low-level output voltage VCC = MIN,
VIL = MAX,
IOL = MAX ±10% V
CC
0.30 0.50 V
VIH = MIN ±5% V
CC
0.30 0.50 V
V
IK
Input clamp voltage VCC = MIN, II = I
IK
–0.73 –1.2 V
I
I
Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA
I
IH
High-level input current VCC = MAX, VI = 2.7V 20 µA
I
IL
Low-level input current ’F06, ’F07 VCC = MAX, VI = 0.5V –0.6 mA
’F06A, ’F07A –0.4 mA
I
CC
Supply current (total) 74F06,
I
CCHVCC
= MAX 5.0 8.0 mA
74F06A
I
CCL
30 43 mA
74F07,
I
CCH
10 14 mA
74F07A
I
CCL
32 45 mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at VCC = 5V, T
amb
= 25°C.
3. Not more than one output should be shorted at a time. For testing I
OS
, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, I
OS
tests should be performed last.
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL PARAMETER
TEST
CONDITION
VCC = +5.0V
T
amb
= +25°C
C
L
= 50pF, RL = 100Ω
VCC = +5.0V ± 10%
T
amb
= 0°C to +70°C
C
L
= 50pF, RL = 100Ω
UNIT
Min Typ Max Min Max
t
PLH
Propagation dela
y
’F06
2.0
1.5
3.5
3.0
6.0
5.5
1.5
1.0
6.5
6.0
ns
PLH
t
PHL
gy
An to Yn
’F06A
Waveform 1
5.0
2.0
9.0
4.0
11.0
6.0
4.0
2.0
15.0
8.0
ns
t
PLH
Propagation delay
’F07
2.0
3.0
4.0
5.0
6.0
7.0
2.0
2.5
6.5
7.5
ns
PLH
t
PHL
gy
An to Yn
’F07A
Waveform 2
6.0
5.0
10.5
7.5
13.0
10.0
5.0
4.0
17.0
13.0
ns
Page 6
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
July 24, 1992
6
TYPICAL PROPAGATION DELAYS VERSUS LOAD FOR OPEN COLLECTOR OUTPUTS
SF00024
0
2
4
6
8
10
12
14
16
18
0 100 200 300 400 500 600
Load resistor (Ω)
Propagation delay (ns)
t
PLH
A versions
t
PLH
non-A versions
t
PHL
both versions
NOTE:
When using Open-Collector parts, the value of the pull-up resistor greatly affects the value of the t
PLH
. For example, changing the specified
pull-up resistor value from 500Ω to 100Ω will improve the t
PLH
up to 50% with only a slight increase in the t
PHL
. However, if the value of the
pull-up resistor is changed, the user must make certain that the total I
OL
current through the resistor and the total IIL’s of the receivers does not
exceed the I
OL
maximum specification.
Page 7
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Hex inverter/buffer drivers (open-collector)
July 24, 1992
7
AC WAVEFORMS
V
M
V
M
V
M
V
M
Yn
An
t
PHL
t
PLH
SF00025
Waveform 1. Propagation delay for inverting outputs
V
M
V
M
V
M
V
M
Yn
An
t
PLH
t
PHL
SF00026
Waveform 2. Propagation delay for non-inverting outputs
NOTE:
For all waveforms, V
M
= 1.5V .
TEST CIRCUIT AND WAVEFORMS
t
w
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
NEGATIVE
PULSE
POSITIVE
PULSE
t
w
AMP (V)
0V
0V
t
THL (tf
)
INPUT PULSE REQUIREMENTS
rep. rate
t
w
t
TLHtTHL
1MHz 500ns
2.5ns 2.5ns
Input Pulse Definition
V
CC
family
74F
D.U.T.
PULSE
GENERATOR
R
L
C
L
R
T
V
IN
V
OUT
Test Circuit for Open Collector Outputs
DEFINITIONS:
R
L
= Load resistor;
see AC electrical characteristics for value.
C
L
= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
T
= Termination resistance should be equal to Z
OUT
of
pulse generators.
t
THL (tf
)
t
TLH (tr
)
t
TLH (tr
)
AMP (V)
amplitude
3.0V 1.5V
V
M
R
L
7.0V
SF00027
Page 8
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Inverter/buffer drivers
1992 Jul 24
8
DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1
Page 9
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Inverter/buffer drivers
1992 Jul 24
9
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1
Page 10
Philips Semiconductors Product specification
74F06, 74F06A,
74F07, 74F07A
Inverter/buffer drivers
yyyy mmm dd
10
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
print code Date of release: 10-98
Document order number: 9397-750-05054
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition
[1]
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
Data sheet status
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Loading...