Page 1
74ALS253
Dual 4–input multiplexer (3–State)
Product specification
IC05 Data Handbook
1991 Feb 08
INTEGRATED CIRCUITS
Page 2
Philips Semiconductors Product specification
74ALS253Dual 4-input multiplexer (3-State)
2
1991 Feb 08 853–1378 01670
FEA TURES
•3-State outputs for bus interface and multiplex operation
•Common select inputs
•Separate output enable inputs
DESCRIPTION
The 74ALS253 has two identical 4-input multiplexers with 3-State
outputs which select 2 bits from four sources by using common
select input (S0, S1). When the individual output enable (OE
a,
OE
b) inputs of the 4-input multiplexers are High, the outputs are
forced to a High impedance (Z) state.
The 74ALS253 is the logic implementation of 2-pole, 4-position
switch being determined by the logic levels supplied to the common
select inputs.
To avoid exceeding the maximum current ratings when the outputs
of the 3-State devices are tied together, all but one device must be
in the High impedance state. Therefore, only one output enable
must be achieved at a time.
TYPE
TYPICAL
PROPAGATION DELAY
TYPICAL
SUPPLY CURRENT
(TOTAL)
74ALS253 7.0ns 8mA
PIN CONFIGURATION
16
15
14
13
12
11
107
6
5
4
3
2
1
Ya
V
CC
I2b
I1b
I0b
I3b
OE
b
S0
OE
a
S1
I0a
I3a
I2a
I1a
98GND Yb
SF00798
ORDERING INFORMA TION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE
V
CC
= 5V ±10%,
T
amb
= 0°C to +70°C
DRAWING
NUMBER
16-pin plastic DIP 74ALS253N SOT38-4
16-pin plastic SO 74ALS253D SOT109-1
16-pin plastic SSOP
Type II
74ALS253DB SOT338-1
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION
74ALS (U.L.)
HIGH/LOW
LOAD VALUE
HIGH/LOW
I0a – I3a Port A data inputs 1.0/1.0 20µA/0.1mA
I0b – I3b Port B data inputs 1.0/1.0 20µA/0.1mA
S0, S1 Common select inputs 1.0/1.0 20µA/0.1mA
OEa Port A Output Enable input (active-Low) 1.0/1.0 20µA/0.1mA
OEb Port B Output Enable input (active-Low) 1.0/1.0 20µA/0.1mA
Ya – Yb 3-State outputs 130/240 2.6mA/24mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
345
V
CC
= Pin 16
GND = Pin 8
SF00799
97
14
2
1
S0
S1
OEa
15
6 13121110
OEb
Ya Yb
I0a I1a I2a I3a I0b I1b I2b I3b
IEC/IEEE SYMBOL
SC00073
MUX
1
6
15
10
11
7
9
0
5
2
EN
4
3
13
12
1
3
0
G
0
3
2
14
2
Page 3
Philips Semiconductors Product specification
74ALS253Dual 4-input multiplexer (3-State)
1991 Feb 08
3
LOGIC DIAGRAM
VCC = Pin 16
GND = Pin 8
SC00074
I0a6I1a5I2a4I3a
3
OEa
1
S12S014I0b10I1b11I2b12I3b13OEb
15
Ya
7
Yb
9
FUNCTION TABLE
INPUTS OUTPUTS
S0 S1 I0 I1 I2 I3 OEn Yn
X X X X X X H Z
L L L X X X L L
L L H X X X L H
H L X L X X L L
H L X H X X L H
L H X X L X L L
L H X X H X L H
H H X X X L L L
H H X X X H L H
H = High voltage level
L = Low voltage level
X = Don’t care
Z = High impedance “off” state
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free air temperature range.)
SYMBOL
PARAMETER RATING UNIT
V
CC
Supply voltage –0.5 to +7.0 V
V
IN
Input voltage –0.5 to +7.0 V
I
IN
Input current –30 to +5 mA
V
OUT
Voltage applied to output in High output state –0.5 to V
CC
V
I
OUT
Current applied to output in Low output state 48 mA
T
amb
Operating free-air temperature range 0 to +70 °C
T
stg
Storage temperature range –65 to +150 °C
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
MIN NOM MAX
UNIT
V
CC
Supply voltage 4.5 5.0 5.5 V
V
IH
High-level input voltage 2.0 V
V
IL
Low-level input voltage 0.8 V
I
IK
Input clamp current –18 mA
I
OH
High-level output current –2.6 mA
I
OL
Low-level output current 24 mA
T
amb
Operating free-air temperature range 0 +70 °C
Page 4
Philips Semiconductors Product specification
74ALS253Dual 4-input multiplexer (3-State)
1991 Feb 08
4
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
1
MIN TYP
2
MAX
UNIT
p
VCC±10%, VIL = MAX,
IOH = –0.4mA V
CC
– 2 V
VOHHigh-level output voltage
CC
,
IL
,
VIH = MIN
IOH = –2.6mA 2.4 V
p
VCC = MIN, VIL = MAX,
I
OL
= 12mA 0.25 0.40 V
VOLLow-level output voltage
CC
,
IL
,
VIH = MIN
I
OL
= 24mA 0.35 0.50 V
V
IK
Input clamp voltage VCC = MIN, II = I
IK
–0.73 –1.5 V
I
I
Input current at maximum input voltage VCC = MAX, VI = 7.0V 0.1 mA
I
IH
High-level input current VCC = MAX, VI = 2.7V 20 µA
I
IL
Low-level input current VCC = MAX, VI = 0.4V –0.1 mA
I
OZH
Off-state output current,
High-level voltage applied
VCC = MAX, VI = 2.7V 20 µA
I
OZL
Off-state output current,
Low-level voltage applied
VCC = MAX, VI = 0.4V –20 µA
I
O
Output current
3
VCC = MAX, VO = 2.25V –30 –112 mA
pp
I
CC
7.0 12 mA
ICCSupply current (total)
I
CCZ
V
CC
=
MAX
9.0 14 mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
CC
= 5V, T
amb
= 25°C.
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, I
OS
.
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL PARAMETER TEST CONDITION
T
amb
= 0°C to +70°C
V
CC
= +5.0V ± 10%
C
L
= 50pF, RL = 500Ω
UNIT
MIN MAX
t
PLH
t
PHL
Propagation delay
In to Yn
Waveform 1
4.0
4.0
12.0
12.0
ns
t
PLH
t
PHL
Propagation delay
Sn to Yn
Waveform 1
5.0
7.0
15.0
16.0
ns
t
PZH
t
PZL
Output enable time, High or Low level
OE
n to Yn
Waveform 2
Waveform 3
1.0
3.0
8.0
9.0
ns
t
PHZ
t
PLZ
Output disable time, High or Low level
OE
n to Yn
Waveform 2
Waveform 3
1.0
1.0
7.0
7.0
ns
Page 5
Philips Semiconductors Product specification
74ALS253Dual 4-input multiplexer (3-State)
1991 Feb 08
5
AC WAVEFORMS
For all waveforms, VM = 1.3V .
V
M
V
M
V
M
V
M
Yn
In, Sn
t
PLH
t
PHL
SF00802
Waveform 1. Propagation Delay for Data and Select to Output
V
M
V
M
V
M
t
PHZ
t
PZH
VOH –0.3V
OE
n
SF00804
0V
Yn
Waveform 2. 3-State Output Enable Time to High Level
and Output Disable Time from High Level
V
M
V
M
V
M
t
PLZ
t
PZL
VOL +0.3V
OE
n
Yn
SC00075
3.5V
Waveform 3. 3-State Output Enable Time to Low Level
and Output Disable Time from Low Level
TEST CIRCUIT AND WAVEFORMS
t
w
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
NEGATIVE
PULSE
POSITIVE
PULSE
t
w
AMP (V)
0.3V
0.3V
t
THL (tf
f
)
INPUT PULSE REQUIREMENTS
Rep.Rate
t
w
t
TLHtTHL
1MHz
500ns
2.0ns 2.0ns
Input Pulse Definition
V
CC
Family
74ALS
D.U.T.
PULSE
GENERATOR
R
L
C
L
R
T
V
IN
V
OUT
Test Circuit for 3-State Outputs
DEFINITIONS:
R
L
= Load resistor;
see AC electrical characteristics for value.
CL= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
T
= Termination resistance should be equal to Z
OUT
of
pulse generators.
t
THL (tf
)
t
TLH (tr
)
t
TLH (tr
)
AMP (V)
Amplitude
3.5V
1.3V
V
M
SC00072
R
L
7.0V
SWITCH POSITION
TEST SWITCH
t
PLZ
, t
PZL
closed
All other open
Page 6
Philips Semiconductors Product specification
74ALS253Dual 4–input multiplexer (3–State)
1991 Feb 08
6
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Page 7
Philips Semiconductors Product specification
74ALS253Dual 4–input multiplexer (3–State)
1991 Feb 08
7
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Page 8
Philips Semiconductors Product specification
74ALS253Dual 4–input multiplexer (3–State)
1991 Feb 08
8
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1
Page 9
Philips Semiconductors Product specification
74ALS253Dual 4–input multiplexer (3–State)
1991 Feb 08
9
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Loading...