Page 1
74ALS153
Dual 4-input multiplexer
Product specification 1991 Feb 08
INTEGRATED CIRCUITS
IC05 Data Handbook
Page 2
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
2
1991 Feb 08 853–1376 01670
FEA TURES
•Non–inverting outputs
•Common select outputs
•Separate enable for each section
•See 74ALS253 for 3–State version
DESCRIPTION
The 74ALS153 has two identical 4–input multiplexer with 3–State
outputs which selects two bits of data from four sources by using
common select inputs (S0, S1). The two 4–input multiplexer circuits
have individual active–Low enables (E
a, Eb) which can be used to
strobe the outputs independently. Outputs (Ya, Yb) are forced Low
when the corresponding enable is high.
The 74ALS153 is the logic implementation of a 2–pole, 4–position
switch where the position of the switch is determined by the logic
levels supplied to the common select inputs.
TYPE
TYPICAL
PROPAGATION DELAY
TYPICAL
SUPPLY CURRENT
(TOTAL)
74ALS153 7.0ns 6.5mA
PIN CONFIGURATION
16
15
14
13
12
11
107
6
5
4
3
2
1
Ya
V
CC
I2b
I1b
I0b
I3b
E
b
S0
E
a
S1
I0a
I3a
I2a
I1a
98GND Yb
SF00146
ORDERING INFORMA TION
ORDER CODE
DESCRIPTION COMMERCIAL RANGE
V
CC
= 5V ±10%,
T
amb
= 0°C to +70°C
DRAWING
NUMBER
16-pin plastic DIP 74ALS153N SOT38-4
16-pin plastic SO 74ALS153D SOT109-1
16-pin plastic SSOP
Type II
74ALS153DB SOT338-1
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
PINS DESCRIPTION
74ALS (U.L.)
HIGH/LOW
LOAD VALUE
HIGH/LOW
Ioa – I3a Port A data inputs 1.0/1.0 20µA/0.1mA
Iob – I3b Port B data inputs 1.0/1.0 20µA/0.1mA
S0, S1 Common select inputs 1.0/1.0 20µA/0.1mA
Ea Port A enable input 1.0/1.0 20µA/0.1mA
Eb Port B enable input 1.0/1.0 20µA/0.1mA
Ya, Yb Data outputs 130/240 2.6mA/24mA
NOTE: One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state.
LOGIC SYMBOL
Ya
7
V
CC
= Pin 16
GND = Pin 8
14
2
1
15
S0
S1
Ea
Eb
I1a I2a
43
SF00147
I3aI0a
65
Yb
9
I1b I2b
12 13
I3bI0b
10 11
IEC/IEEE SYMBOL
SF00148
1
6
5
EN
0
1
14
0
2
1
7
G
0
3
MUX
4
3
2
3
15
10
11
9
12
13
Page 3
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
3
LOGIC DIAGRAM
7
Ya Yb
9
1 65432141011121315
V
CC
= Pin 16
GND = Pin 8
E
a EbI0a I1a I2a I3a S1 S2 I0b I0b I2b I3b
SF00149A
FUNCTION TABLE
INPUTS OUTPUT
S0 S1 I0n I1n I2n I3n En Yn
L L L X X X L L
L L H X X X L H
H L X L X X L L
H L X H X X L H
L H X X L X L L
L H X X H X L H
H H X X X L L L
H H X X X H L H
H = High voltage level
L = Low voltage level
X = Don’t care
Page 4
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
4
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
SYMBOL
PARAMETER RATING UNIT
V
CC
Supply voltage –0.5 to +7.0 V
V
IN
Input voltage –0.5 to +7.0 V
I
IN
Input current –30 to +5 mA
V
OUT
Voltage applied to output in high output state –0.5 to V
CC
V
I
OUT
Current applied to output in Low output state 48 mA
T
amb
Operating free-air temperature range 0 to +70 °C
T
stg
Storage temperature range –65 to +150 °C
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
MIN NOM MAX
UNIT
V
CC
Supply voltage 4.5 5.0 5.5 V
V
IH
High-level input voltage 2.0 V
V
IL
Low-level input voltage 0.8 V
I
Ik
Input clamp current –18 mA
I
OH
High-level output current –2.6 mA
I
OL
Low-level output current 24 mA
T
amb
Operating free-air temperature range 0 +70 °C
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
1
MIN TYP
2
MAX
UNIT
p
VCC = ±10%, VIL = MAX,
IOH = –0.4mA V
CC
– 2 V
VOHHigh-level output voltage
CC
,
IL
,
VIH = MIN
IOH = MAX 2.4 3.2 V
p
VCC = MIN, VIL = MAX,
I
OL
= 12mA 0.25 0.40 V
VOLLow-level output voltage
CC
,
IL
,
VIH = MIN
I
OL
= 24mA 0.35 0.50 V
V
IK
Input clamp voltage VCC = MIN, II = I
IK
–0.73 –1.5 V
I
I
Input current at minimum input
voltage
VCC = MAX, VI = 7.0V 0.1 mA
I
IH
High-level input current VCC = MAX, VI = 2.7V 20 µA
I
IL
Low-level input current VCC = MAX, VI = 0.4V –0.1 mA
I
O
Output current
3
VCC = MAX, VO = 2.25V –30 –112 mA
I
CC
Supply current (total) VCC = MAX 6.5 12 mA
NOTES:
1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2. All typical values are at V
CC
= 5V, T
amb
= 25°C.
3. The output conditions have been chosen to produce a current that closely approximates one half of the true short-circuit output current, I
OS
.
Page 5
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
5
AC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL PARAMETER TEST CONDITION
T
amb
= 0°C to +70°C
V
CC
= +5.0V ± 10%
C
L
= 50pF, RL = 500Ω
UNIT
MIN MAX
t
PLH
t
PHL
Propagation delay
In to Yn
Waveform 1
4.0
4.0
12.0
12.0
ns
t
PLH
t
PHL
Propagation delay
Sn to Yn
Waveform 2
5.0
7.0
15.0
16.0
ns
t
PLH
t
PHL
Propagation delay
E
n to Yn
Waveform 2
3.0
5.0
10.0
12.0
ns
AC WAVEFORMS
For all waveforms, VM = 1.3V .
V
M
V
M
V
M
V
M
Yn
In
t
PLH
t
PHL
SF00150
Waveform 1. Propagation Delay for Data to Output
V
M
V
M
V
M
V
M
Yn
Sn
t
PLH
t
PHL
SC00046
En
Waveform 2. Propagation Delay for Select or Enable to Output
TEST CIRCUIT AND WAVEFORMS
t
w
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
90%
V
M
10%
NEGATIVE
PULSE
POSITIVE
PULSE
t
w
AMP (V)
0.3V
0.3V
t
THL (tf
f
)
INPUT PULSE REQUIREMENTS
Rep.Rate
t
w
t
TLHtTHL
1MHz
500ns
2.0ns 2.0ns
Input Pulse Definition
V
CC
Family
74ALS
D.U.T.
PULSE
GENERATOR
R
L
C
L
R
T
V
IN
V
OUT
Test Circuit for Totem-pole Outputs
DEFINITIONS:
R
L
= Load resistor;
see AC electrical characteristics for value.
CL= Load capacitance includes jig and probe capacitance;
see AC electrical characteristics for value.
R
T
= Termination resistance should be equal to Z
OUT
of
pulse generators.
t
THL (tf
)
t
TLH (tr
)
t
TLH (tr
)
AMP (V)
Amplitude
3.5V
1.3V
V
M
SC00005
Page 6
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
6
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
Page 7
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
7
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
Page 8
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
8
SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm SOT338-1
Page 9
Philips Semiconductors Product specification
74ALS153Dual 4-input multiplexer
1991 Feb 08
9
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
LIFE SUPPORT APPLICA TIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
DEFINITIONS
Data Sheet Identification Product Status Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Copyright Philips Electronics North America Corporation 1997
All rights reserved. Printed in U.S.A.
Loading...