Page 1
www.jxlcd.com
www.jxlcd.com
Page 2
CONTENTS
REVISION HISTORY
GENERAL DESCRIPTION
1. ABSOLUTE MAXIMUM RATINGS
1.1 ABSOLUTE RATING OF ENVIRONMENT
1.2 ELECTRICAL ABSOLUTE RATINGS
1.3 MECHANICAL RATINGS
1.4 THE OTHERS
2. ELECTRICAL SPECIFICATIONS
2.1 TFT LCD MODULE
2.2 BACKLIGHT UNIT
2.3 MATERIAL LIST CONCERNING EMI REGULATIONS
3. INTERFACE SPECIFICATIONS
3.1 THE PIN ASSIGNMENT OF LVDS INTERFACE CONNECTOR
3.2 INPUT SIGNAL TIMING SPECIFICATIONS
3.3 COLOR DATA INPUT ASSIGNMENT
3.4 POWER UP/DOWN SEQUENCE
4. OPTICAL SPECIFICATIONS
4.1 TEST CONDITIONS
4.2 OPTICAL SPECIFICATIONS
5. MECHNICAL DRAWING
6. PRECAUTION
6.1 ASSEMBLY AND HANDLING PRECAUTION
6.2 SAFTY PRECAUTION
7. PACKING
7.1 PACKING SPECIFICATIONS
7.2 PACKING METHOD
8. DEFINITION OF SHIPPING LABEL ON MODULE
Attached 1, Drawing
Attached 2, TFT LCD Inspection Specification
www.jxlcd.com
www.jxlcd.com
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
2 / 27
Version 3.1
Page 3
Version Date
Ver 3.0
Ver 3.1
Dec. 30,’02
Jan. 21, ‘03 9
www.jxlcd.com
www.jxlcd.com
Page
(New)
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
REVISION HISTORY
Section Description
Final approval sheet is released.
2.2
Revise connector PN to be
Note (1) Connector PN.: BHTR-02VS-1
Note (2) User’s connector Part No.: SM02B-BHTS-B-TB or
Remove Page 28~ Outgoing inspection Criteria
or equivalent
equivalent
3 / 27
Version 3.1
Page 4
Issued Date: Jan. 21, 2003
/
Model No. : N150X2-L01
Approval
GENERAL DESCRIPTION
OVERVIEW
This product is a 15” TFT Liquid Crystal Display Module with a Backlight unit and 30 pins LVDS (Low Voltage
Differential Signal) interface. This module supports 1024 x 768 XGA mode and can display 262,144 colors. The
inverter module for Backlight is not built in.
BLOCK DIAGRAM
Rxin0(+/-)
Rxin1(+/-)
Rxin2(+/-)
CLK(+/-)
Vcc
GND
Data
CLK
V
EDID
EDID
EDID
LVD S I NPU T
(JAE-FI-XB30S-HF10)
INPUT CONNECTOR
TIMING CONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
GENERATOR
EDID
EEPROM
SCAN DRIVER IC
TFT LCD PANEL
(1024xR.G.B.x768)
DATA DRIVER IC
VL
LAMP CONNECTOR
(JST-BHTR-02VS-1)
BACKLIGHT UNIT
www.jxlcd.com
www.jxlcd.com
APPLICATION
-Note Book PC
GENERAL SPECIFICATI0NS
Item Specifications Unit
Screen Size 15.0 Diagonal inch
Bezel opening area 307.6(W)x231.6(H) mm
Effective display area 304.1(W)x228.1(H) mm
Pixel number 1024 x R.G.B x768 pixel
Pixel pitch 0.297(H) x 0.297(V) mm
Pixel Arrangement R.G.B Vertical Stripe Display Color 6 bits, 262,144 color
Transmissive mode Normally white Surface treatments Hard coating (3H) and Anti-glare (Haze 25%) -
MECHANICAL SPECIFICATIONS
ITEM MIN. TYP. MAX. Unit Note
Module
Size
Note 1: The maximum thickness of I/O connector area is 6.0mm.
Horizontal 315.5 315.8 316.1 mm Vertical 240.2 240.5 240.8 mm Depth - 5.7 6.0 mm (1)
Weight 480 490 500 g -
4 / 27
Version 3.1
Page 5
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
1. ABSOLUTE MAXIMUM RATINGS
1.1 ABSOLUTE RATING OF ENVIRONMENT
Item Symbol Min. Max. Unit Note
Operating Ambient Temperature TOP 0 +50
Operating Temperature for Panel - 0 +60
Storage Temperature T
Operating Ambient Humidity HOP 20 90 %RH (1)
Storage Humidity H
Air Pressure - 70.0 - kPa Operation
Air Pressure - 12.0 - kPa Non-Operation
Altitude - - 4572 m Operation
Altitude - - 15240 m Non-Operation
Note. (1) Wet bulb temperature should be 39°C Max, and no condensation of water.
(2) The surface temperature caused by self-heat radiation of cell itself is specified on this item.
-20 +60
STG
10 90 %RH (1)
STG
°C
°C
°C
-
(2)
-
1.2 ELECTRICAL ABSOLUTE RATINGS
(1) TFT LCD Module
Parameter Symbol
Power supply voltage VCC -0.3 +4.0 V
Logic input voltage VIN -0.3 VCC+0.3 V
(2) Backlight Unit
Lamp voltage VL - 2.5K V
Lamp current IL 1.8 7.0 mA
Lamp frequency fL - 80 KHz -
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
www.jxlcd.com
www.jxlcd.com
Parameter Symbol
Values
Min. Max.
Values
Min. Max.
Unit Remarks
Ta=0~50ºC
Unit Remarks
RMS
RMS
Note (1)
-
5 / 27
Version 3.1
Page 6
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
1.3 MECH ANICAL RATIN GS
LCD shall have no failure in the following reliability items.
Item Test Conditions Note
Mechanical
Vibration
Mechanical Shock
Pressure
Resistance
Strength of FL Cable
www.jxlcd.com
Connector tension
test
Assured torque
value at side-mount
part
Rescrewed test 10 times under 245.0 mN⋅m (2.5 kgf⋅cm) Non Operation
Tapping test Test “ Ripple “ Phenomenon. Operation
www.jxlcd.com
Frequency Range 5 – 500 Hz, 14.7m/s2 (1.5G) constant,
0.5Hrs each axis (X, Y, Z direction)
Frequency Range 5 – 500 Hz, 4.9m/s
0.5Hrs each axis (X, Y, Z direction)
686m/s2(70G), Pulse width 11 ms, Half-Sine Wave, ±X, ±Y, ±Z
direction, each 3 times.
2548m/s
direction, each 1 time
No Destruction with the force 196 N (20 kgf, 16 mm in diameter) to
the display surface at the vertical direction
No Destruction with the force 294.2 N (30 kgf, 30 mm in diameter)
to the back of the display surface at the vertical direction
Strength of
rotation
force
Lead pull
test
Input connector: With 50 times of connector trial there must be no
damage to the shape and functional.
Back light connector: With 50 times of connector trial there must
be no damage to the shape and functional.
245 mN⋅m (2.5 kgf⋅cm) Non Operation
2
(260G), Pulse width 2mS, Half-Sine Wave, ±X, ±Y, ±Z
Cable: No disconnection of cable to the 5 trial of
360 degree rotation.
See a bent state of cable.
Connector: No disconnection of cable to 10 trial of
180 degree rotation.
See a bent state of cable.
Soldering portion: 14.7N (1.5kgf), 1min
Connector: 14.7N (1.5kgf), 1 sec
2
(0.5G) constant,
Non Operation
Operation
Operation and
Non Operation
Non Operation
Fig 1-3-1
Fig 1-3-2
Fig 1-3-3
Non Operation
FL
R2
Non Operation
Definitions of failure for judgment shall be as follows:
1) Function of the module should be maintained.
2) Current consumption should be smaller than the specified value.
3) Appearance and display quality should not have distinguished degradation.
4) Luminance should be larger than the minimum value specified in optical specification.
6 / 27
Version 3.1
Page 7
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
NOTE
(1) The compression condition of front side
(a) Compression point: 12 points ( refer to Fig 1-3-1)
(b) Compression condition: Time 3 sec, Tool diameter: 16 mm in diameter (refer to Fig 1-3-3)
: COMPRESSION POINT
Approval
Flat plate
Fig 1-3-1
(2) The compression condition of rear side
(a) Compression point: 21 points (refer to Fig 1-3-2 )
(b) Compression condition: Time 3 sec, Tool radius: 30 mm in diameter (refer to Fig 1-3-3)
www.jxlcd.com
www.jxlcd.com
:COMPRESSION POINT
ABS natural 2.0t
Flat plate
LCD
LCD
Fig 1-3-2
(3) Dimension of the compression jig
(a) compression jig for front side A = 16 mm in diameter
B = 16 mm in diameter
(b) compression jig for rear side A = 30 mm in diameter
B = 28 mm in diameter
(4) Recommend Torque is 1.3 – 1.5 kgf
7 / 27
Rubber sheet
10 mm diameter
B
A
Fig 1-3-3
10
16
1.5
Version 3.1
Page 8
1.4 THE OTHERS
(1) Static electricity pressure resistance
Items Testing conditions Operation Non Operation
Contact discharge 150pF, 330 ohm
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
±10 kV ±10 kV
Air discharge 150pF, 330 ohm
ESD Acceptance Definition:
Temporary performance degradation. Recovery by operator is acceptable. No hardware failure.
(2) Sound noise
There should be no uncomfortable noise.
Being used under whatever surrounds, when power on/off, the panel should not generate uncomfortable
noise.
(3) Open / Short
No smoke, no firery at any open/ short test
(4) MTBF : 50000 Hr (except for backlight lamp)
www.jxlcd.com
www.jxlcd.com
±20 kV ±20 kV
8 / 27
Version 3.1
Page 9
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
2. ELECTRICAL SPECIFICATIONS
2.1 TFT LCD MODULE
MODULE
Parameter Symbol
Power Supply Voltage VCC 3.0 3.3 3.6 V
“H” level LVDS signal input VIH - - +100 mV
“L” level LVDS signal input VIL -100 - - mV
White 270 300 330 mA
Power Supply Current
Rush Current I
Ripple voltage VRP - 50 100 mV
Terminating resistor Rt - 100 - Ohm
LCD Fuse name: Kamaya(FCC16-162ABTP)
Black 310 360 420 mA
Maximum
l
CC
RUSH
Min. Typ. Max.
470 540 600 mA
- 1.0 1.5 A (2)
Value
Unit Notes
2.2 BACKLIGHT UNIT
Approval
(1)
(9)
(1)
LAMP : Harison, MBVK2JB45YX309.5NCLFH/CS2
BACKLIGHT ( 1 Lamp)
Parameter Symbol
Lamp Voltage VL 617 685 754 V
Lamp Current IL 2.0 6.0 6.5 mA (3)
Startup Voltage VS
www.jxlcd.com
Operating Frequency FL 40 60 80 KHz (5)
Power Consumption PL - 4.11 - W (6), IL=6.0mA
Lamp Life time LBL 10000 15000 - Hrs (7)
Note (1) Connector PN.: BHTR-02VS-1 or equivalent
Note (2) User’s connector Part No.: SM02B-BHTS-B-TB or equivalent
www.jxlcd.com
The connector information of Black light unit.
Pin Symbol Description Remark
1 HV Lamp power input Pink
2 LV Ground White
Min. Typ. Max.
- - 1150 (25oC) V
- - 1500 (0
Value
o
C) V
Unit Notes
IL=6.0mA
RMS
(4)
RMS
(4)
RMS
2.3 MATERIAL LIST CONCERNING EMI REGULATIONS
(1) EMI Regulations:
“N150X2-L01” which is assembled inside Toshiba’s Satellite model should be met to the
regulations as below:
CISPR: Pub.22 Class B
FCC : Part 15 Class B
VCCI
(2) Safety regulation (CMO TFT-LCD module only): UL 1950
: Class B
9 / 27
Version 3.1
Page 10
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
1. EMI Filter Silk Product Code Rating Maker
Bead R407 BK1608LL241 240 Ohm/100MHz TAIYO YU DEN Co.,JPN
Bead LA1~LA10 BK32164M121 120 Ohm/100MHz TAIYO YU DEN Co.,JPN
Bead R406,424 BK1608LL121
2. DC/DC Converter Silk Osc. Freq. Maker
PWM IC U9 Typ 1.2 MHz. Linear Technology
Note (1) Operating Temp. range is 0 ~ 50 ºC
120 Ohm /
100MHz
Note (2) Measurement Conditions is as below. Them maximum Vcc drop voltage that caused by rush
current when switching-on should not be more than 0.5V.
+3.3
2SK1475
47kΩ
+12V
1 kΩ
SW
2SK14
www.jxlcd.com
www.jxlcd.com
Output To VCC (LCD module)
IF SW is High,
Output is 0V.
IF SW is Low,
Output is +3.3V
0.01µF / 50V
TAIYO YO DEN Co.,JPN
VCC rising time is 5ms
Note (3) Lamp current is measured by utilizing a current meter for high frequency as shown below:
Note (4) The voltage shown above should be applied to the lamp for more than 1 second after startup.
GND
LCD
Module
0.1VCC
0.9VCC
5ms
Hot(Pink
GND(White)
)
3.3V
1
2
( Yokogawa 2016 )
10 / 27
A
Current meter
Inverter
Version 3.1
Page 11
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
Otherwise the lamp may not be turned on.
Note (5) The lamp frequency may produce interference with horizontal synchronous frequency from
the display, and this may cause line flow on the display. In order to avoid interference the
lamp frequency should be detached from the horizontal synchronous frequency and its
harmonics as far as possible.
Note (6) P
Note (7) The lifetime (Hr) of a lamp can be defined as the time in which it continues to operate under
Note (8) The waveform of the voltage output of inverter must be area-symmetric and the design of
= IL×VL.
L
the condition Ta = 25±2℃ and I
(1) When the brightness becomes 50% or lower than its original,
(2) When the effective ignition length becomes 80% or lower than its original value.
(Effective ignition length is defined as an area that has less than 70% brightness compared
to the brightness in the center point.)
the inverter must have specifications for the modularized lamp. The performance of the
backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the
DC-AC inverter for the lamp. All the parameters of an inverter should be designed with care
www.jxlcd.com
www.jxlcd.com
so as not to produce too much current leakage from high-voltage output of the inverter.
When designing or ordering the inverter, please make sure that a poor lighting caused by
the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs.
When the above situation is confirmed, the module should be operated in the same
= 2.0 ~ 6.5 mArms until one of the following event occurs :
L
manners as it is installed in your instrument.
Note (9) The specified power supply current is under the conditions , Ta = 25 ± 2 ºC, fv = 60 Hz,
whereas a power dissipation check pattern below is displayed. In case of white patten and
black pattern, the maximum value is measured when VCC=3.0V, the typical value is
measured when VCC=3.3V and the minimum value is measured when VCC=3.6V. In case
of maximum pattern, the maximum value is measured when VCC=3.6V, the typical value is
measured when VCC=3.3V and the minimum value is measured when VCC=3.0V.
11 / 27
Version 3.1
Page 12
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
a. White Pattern
Active Area
c. Maximum pattern (Zoom in)
R R G G B B RRG G B
B B R
b. Black Pattern
gray level = 0
…
B
R R G G B B RRG G B
B
R
B B R
R
expend to whole
active area
gray level = 7
…expend to whole active area
www.jxlcd.com
www.jxlcd.com
12 / 27
Version 3.1
Page 13
3. INTERFACE SPECIFICATIONS
3.1 THE PIN ASSIGNMENT OF LVDS INTERFACE CONNECTOR.
Pin Symbol Description Polarity Remark
1 Vss Ground
2 Vcc Power Supply +3.3 V (typical)
3 Vcc Power Supply +3.3 V (typical)
4 NC Non-Connection
5 NC Non-Connection
6 NC Non-Connection
7 NC Non-Connection
8 Rxin0- LVDS Differential Data Input Negative
9 Rxin0+ LVDS Differential Data Input Positive
10 Vss Ground
11 Rxin1- LVDS Differential Data Input Negative
12 Rxin1+ LVDS Differential Data Input Positive
13 Vss Ground
14 Rxin2- LVDS Differential Data Input Negative
15 Rxin2+ LVDS Differential Data Input Positive
16 Vss Ground
17 CLK- LVDS Clock Data Input Negative LVDS Level Clock
18 CLK+ LVDS Clock Data Input Positive
19 Vss Ground
20 NC Non-Connection
21 NC Non-Connection
www.jxlcd.com
www.jxlcd.com
22 Vss Ground
23 NC Non-Connection
24 NC Non-Connection
25 Vss Ground
26 NC Non-Connection
27 NC Non-Connection
28 Vss Ground
29 NC Non-Connection
30 NC Non-Connection
Note (1) Connector Part No.: JAE-FI-XB30S-HF10 or equivalent.
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
DDC 3.3V Power
(reserved)
DDC Clock (reserved)
DDC Data (reserved)
R0~R5,G0
-
G1~G5,B0,B1
-
B2~B5,DE,Hsync,Vsync
Note (2) User’s connector Part No: JAE-FI-X30M or equivalent.
Note (3) The first pixel is even.
13 / 27
Version 3.1
Page 14
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
3.2 INPUT SIGNAL TIMING SPECIFICATIONS
The specifications of input signal timing are as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Clock Frequency 1/Tc 50 65 68 MHz Frame Frequency Cycle TV 771 806 850 TH Vertical Active Display Term Display Period TVD 768 768 768 TH One Line Scanning Time Cycle TH 1200 1344 1500 Tc Horizontal Active Display Term Display Period THD 1024 1024 1024 Tc -
Note (1) The duration of DE signal must be longer than 1 clock period at every horizontal sync. period.
INPUT SIGNAL TIMING DIAGRAM
DE
DCLK
C
www.jxlcd.com
DE
DATA
www.jxlcd.com
T
Valid display data (1024 pixels)
T
T
HD
14 / 27
Version 3.1
Page 15
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
3.3 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input
for the color. The higher the binary input, the brighter the color. The table below provides the
assignment of color versus data input.
Data Signal
Color
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Black
Red
Green
Basic
Colors
Gray
Scale
Of
Red
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Blue
Cyan
Magenta
Ye ll ow
White
Red(0)/Dark
Red(1)
Red(2)
:
:
Red(61)
Red(62)
Red(63)
Green(0)/Dark
Green(1)
Green(2)
:
www.jxlcd.com
Green(61)
Green(62)
Green(63)
Blue(0)/Dark
Blue(1)
Blue(2)
Blue(61)
Blue(62)
Blue(63)
:
www.jxlcd.com
:
:
0
1
0
0
0
1
1
1
0
0
0
:
:
1
1
1
0
0
0
:
:
0
0
0
0
0
0
:
:
0
0
0
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
1
0
1
1
1
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
1
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
Approval
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
:
:
:
:
:
:
1
0
1
1
0
1
1
1
1
1
1
1
:
:
:
:
:
:
15 / 27
Version 3.1
Page 16
3.4 POWER UP/DOWN SEQUENCE & VCC DIP CONDITIONS
3.4.1 POWER UP/DOWN SEQUENCE
Power On
Power Off
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
Restart
Power Supply
for LCD, Vcc
- Interface Signal
(LVDS Signal of
Transmitter), V
- Power for Lamp
Timing Specifications:
www.jxlcd.com
0 < t1 ≦ 10 msec
www.jxlcd.com
0 < t2 ≦ 50 msec
90%
0V
0V
I
10%
t1
Valid Data
ONOFF OFF
90%
t6 t5
50%50%
t4
10%
t3 t2
0 < t3 ≦ 50 msec
t4 ≧ 300 msec
t5 ≧ 100 msec
t6 ≧ 100 msec
Note (1) Please avoid floating state of interface signal at invalid period.
Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to 0 V.
Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the
interface signal is valid. The Backlight inverter power must be turned off before the power
supply for the logic and the interface signal is invalid.
16 / 27
Version 3.1
Page 17
3.4.2 VCC DIP CONDITIONS
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
(1) 2.5V≦ VCC< 3.0V
Td≦20 ms
(2) VCC< 2.5V
Vcc-Dip conditions also follow the power up/down conditions for supply voltage.
Td
3.0 V
VCC
GND
www.jxlcd.com
www.jxlcd.com
17 / 27
Version 3.1
Page 18
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
4. OPTICAL SPECIFICATIONS
4.1 TEST CONDITIONS
Ambient Temperature : Ta = 25±2oC
Ambient Humidity : H
Supply Voltage : Vcc = 3.3V
Input Signal : According to typical value in "Electrical Characteristics"
FL Input Current : I
FL Driving Frequency : f
FL Inverter : HBL-0237 (Tamura)
The measuring method is shown in 4.2. The following items are measured under stable conditions. The
optical characteristics should be measured in a dark room ( Screen luminance < 2-lx ) or equivalent state
with the methods shown in Note (6).
4.2 OPTICAL SPECIFICATIONS
Item Symbol Conditions
Contrast Ratio CR
Response Time
Average luminance of
white ( 5 points )
Cross Modulation D
Luminance
Uniformity
Chromaticity
Viewing Angle
13 Points White
Variatio n
13 Points CR Variation
White Variation dL
www.jxlcd.com
www.jxlcd.com
Red
Green
White
Hor.
Ver.
Hor.
Ver.
50±10%RH
a
=6.0mArms
FL
= 50 kHz
FL
Specifications
Min. Typ. Max.
200 250 - - (2),(6)
AVE
TR - 6 10 ms
- 17 25 ms
T
F
Y
140 170 - cd/m2
L,AVE
θ
= θY =0°
- - 1.0 % (5)
SHA
Rx 0.569 0.599 0.629 Ry 0.316 0.346 0.376 Gx 0.299 0.329 0.359
Gy 0.495 0.525 0.555
Bx 0.121 0.151 0.181 Blue
By 0.097 0.127 0.157
Wx 0.306 0.336 0.366 Wy
θX+
θ
X-
θY+
θ
Y-
θX+
θ
X-
θY+
θ
Y-
δW
δC
R
X
Viewing normal angle
Center
CR>=10
Center
CR>=5
= θY =0°
θ
X
Viewing normal angle
0.314 0.344 0.374 40 45 40 45 15 20 35 40 50 55 50 55 25 30 40 45 -
1.0 1.3 1.6 - (7)
- 2.0 2.5 - (7)
- - 1.5 %/mm (8)
Unit Note
=6.0mArms *
I
FL
Gray Scale
Level=L63 (White)
(1), (6)
deg.
(3)
(4)
18 / 27
Version 3.1
Page 19
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
Item Symbol Conditions
63
60
56
52
48
44
40
36
Gamma
PS. Because of the color measurement discrepancy between TSB &CMO is (△Wx,△Wy)=>(0.01,0.009),
32
28
24
20
16
12
8
4
0
θ
= θY =0°
X
Viewing normal angle
Specifications
Min. Typ. Max.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.0%
0.2%
1.1%
2.6%
4.9%
8.0%
12.0%
16.8%
16.8%
29.2%
36.8%
45.4%
55.0%
65.6%
77.2%
89.8%
100.0%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Unit Note
(1) (6)
%
at center of
Viewing area
center only
CMO internal spec of White is (Wx,Wy)Typ =>(0.326,0.335)
(Wx,Wy)Max=>(0.356,0.365)
(Wx,Wy)Min=>(0.296,0.305)
www.jxlcd.com
www.jxlcd.com
19 / 27
Version 3.1
Page 20
Note (1) Definition of Viewing Angle θx and θy :
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
θX- = 90º
x-
6 o’clock
θ
y- = 90º
y-
Note (2) Definition of Contrast Ratio :
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L63 / L0
L63 : Luminance on the white raster (gray scale level L63)
L 0 : Luminance on the black raster (gray scale level L0)
www.jxlcd.com
www.jxlcd.com
CR
= ( CR(4)+CR(5)+CR(7)+CR(9)+CR(10) )/ 5
AVE
CR(X) is correspond to the Contrast Ratio of a point of X at Figure of Note (7).
Note (3) Definition of Response time :
Normal
θx = θy = 0º
θy- θy+
θx−
θx+
12 o’clock direction
y+
θ
y+ = 90º
x+
θX+ = 90º
100%
90%
Optical
Response
10%
0%
White L63
TR
Black L0
20 / 27
TF
White L63
time
Version 3.1
Page 21
A
(
)
A
(
)
(
)
Note (4) Definition of Average Luminance of White :
measure the luminance of white at 5 points.
Average Luminance of White Y
Y
= ( Y L4+ Y L5+ Y L7+ Y L9+ Y
L,AVE
Y
is correspond to the Luminance of a point of X at Figure of Note (7).
LX
Note (5) Definition of Cross Modulation (D
D
= | YB – YA | / YA ×100 (%)
SHA
Where :
Y
= Luminance of measured location without darkest gray pattern (cd/m2)
A
Y
= Luminance of measured location with darkest gray pattern (cd/m2)
B
L,AVE
SHA
) / 5
L10
)
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
(0, 0)
Y
(128, 384)
A,L
Y
(512, 672)
A, D
Note (6) Measuring setup :
www.jxlcd.com
www.jxlcd.com
The measurement suppose to be executed after stabilized the panel at given temperature during 30min.
in the case of abrupt temperature change. The measurement shall be executed 30 minutes after lighting
at rating. The luminance of white should be typical luminance ( Typical Condition IL=6.0mA ). In order to
stable the luminance, LCD shall not be gotten winds.
Gray 32
LCD module
LCD panel
ctive
Y
A, R
1023, 767
Center of the screen
(896, 384)
Y
B, L
Y
B, D
0, 0
(256, 192)
(128, 384)
(512, 672)
ctive
Gray 0
Gray 32
Y
(512, 96)
B,U
Y
(896, 384)
B,R
(768, 576)
1023, 767
500 mm
Field of view = 2°
Photometer
(TOPCON BM-5A)
Light Shield Room
( Screen illuminance < 2-lx)
21 / 27
Version 3.1
Page 22
Issued Date: Jan. 21, 2003
X
Model No. : N150X2-L01
Note (7) Definition of 13 points white variation δW, CR variation δC
δW = Maximum luminance of 13 points / Minimum luminance of 13 points
δC
= Maximum CR 13 points / Minimum CR of 13 points
R
0 255 511 767 1023
Horizontal Line number
0
45
191
383
575
Vertical Line number
722
767
45
3
12 11
10
9
8
7 6
5 4
3 2 1
Active area
R
978
Note (8) Definition of White Variation dL : measure the luminance of white at 13 ×11 po i nts.
dL = | L(x,y) – L(x+I, y+j)| / ( L(x,y) × D(x+I, y+j) ) ×100 (%/mm)
where 2 ≤ x ≤ 12, 2 ≤ y ≤ 10, I = ± 1, j = ± 1
www.jxlcd.com
www.jxlcd.com
13
Approval
: test point
11 points
8.75 8.75
8.75
φ17.5mm
8.75
Active area
Measuring Spot
( Field of View : 2deg. Measuring Distance : 500mm)
φ17.5mm
22 / 27
L(x-1,y-1)
D(x+1,y-1)
L(x+1,y-1)
L(x,y)
L(x+1,y+1)
Version 3.1
Page 23
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
5. MECHNICAL DRAWING
Please refer to the attached drawings.
6. PRECAUTION
6. 1 ASSEMBLY AND HANDLING PRECAUTION
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil may
cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and backlight will be
damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent
damage to the CMOS LSI chips during latchup.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily
scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD
module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD module within the
specified storage conditions.
(10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the response
time will become slowly, and the starting voltage of CCFL will be higher than room temperature.
6.2 SAFTY PRECAUTION
(1) The startup voltage of backlight is approximately 1000 Volts. It may cause electrical shock while assembling
with inverter. Do not disassemble the module or insert anything into the backlight unit.
(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of
contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
www.jxlcd.com
www.jxlcd.com
23 / 27
Version 3.1
Page 24
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
7. PACKAGING
7.1 PACKING SPECIFICATIONS
(1) 10 LCD modules / 1 Box
(2) Box dimensions : 422(L) X 337(W) X 345(H) mm
(3) Weight : approximately 6.5Kg (10 modules per box)
7.2 PACKING METHOD
(1)Carton Packing should have no failure in the following reliability test items.
Test Item Test Conditions Note
Frequency Range: 5 – 50 Hz, Degree of acceleration 9.8 m/s
Vibration
Dropping Test 1 Angle, 3 Edge, 6 Face, 60cm Non Operation
Sweep rate 3 minutes
Top & Bottom 60 minutes, Right & Left 15 minutes, Back & Forth 15
minutes
2
(1G).
Non Operation
Approval
www.jxlcd.com
www.jxlcd.com
Figure. 7-1 Packing method
24 / 27
Version 3.1
Page 25
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
www.jxlcd.com
www.jxlcd.com
Figure. 7-2 Packing method
25 / 27
Version 3.1
Page 26
8. DEFINITION OF SHIPPING LABEL ON MODULE
(1) CMO Label
The barcode nameplate is pasted on each module as illustration, and its
definitions are as following explanation.
G33C0000M110
E207943
N150X2-L01 Rev.XX
MADE IN TAIWAN
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
XXXXXXXYMDLN
(a) Model Name : N150X2-L01
(b) Revision : Rev.XX, for example : C1, C2 …etc.
(c) Serial ID: X X
www.jxlcd.com
www.jxlcd.com
Serial ID include the information as list.
NNN
70mm X 24mm
X X X X X Y M D L N N N N
Serial No.
Product Line
Year, Month, Date
CMO Internal Use
Revision
CMO Internal Use
(a)Manufactured Date: Year: 1~9, for 2001~2009
Month: 1~9, A~C, for Jan. ~ Dec.
Day: 1~9, A~Y, for 1
(b)Revision Code: cover all the change
(c)Serial No.: Manufacturing sequence of product
(d)Product Line: 1 -> Line1, 2 -> Line 2, …etc.
26 / 27
st
to 31st, exclude I , O and U
Version 3.1
Page 27
(2) Carton Label
Issued Date: Jan. 21, 2003
Model No. : N150X2-L01
Approval
(3) Pallet Label
www.jxlcd.com
VF2093P01
G33C0000M110
G33C0000M110
VF2093P01
www.jxlcd.com
27 / 27
Version 3.1
Page 28
www.jxlcd.com
www.jxlcd.com
Page 29
www.jxlcd.com
www.jxlcd.com
Loading...