Datasheet MX29L1611GPC-10, MX29L1611GPC-12, MX29L1611GPC-90, MX29L1611PC-10, MX29L1611PC-12 Datasheet (MXIC)

...
Page 1
FEATURES
ADVANCED INFORMATION
MX29L1611G / MX29L1611*
16M-BIT [2M x 8/1M x 16] CMOS
SINGLE VOLTAGE FLASH EEPROM
• 3.3V ± 10% for write and read operation
• 11V Vpp erase/programming operation
• Endurance: 100 cycles
• Fast random access time: 90ns/100ns/120ns
• Fast page access time: 30ns (Only for 29L1611PC-90/ 10/12)
• Sector erase architecture
- 32 equal sectors of 64k bytes each
- Sector erase time: 200ms typical
• Auto Erase and Auto Program Algorithms
- Automatically erases any one of the sectors or the whole chip
- Automatically programs and verifies data at specified addresses
GENERAL DESCRIPTION
The MX29L1611G is a 16-mega bit Flash memory organized as either 1M wordx16 or 2M bytex8. The MX29L1611G includes 32 sectors of 64KB(65,536 Bytes or 32,768 words). MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29L1611G is packaged in 42 pin PDIP.
The standard MX29L1611G offers access times as fast as 100ns,allowing operation of high-speed microprocessors without wait. To eliminate bus contention, the MX29L1611G has separate chip enable CE and, output enable (OE).
• Status Register feature for detection of program or erase cycle completion
• Low VCC write inhibit is equal to or less than 1.8V
• Software data protection
• Page program operation
- Internal address and data latches for 64 words per page
- Page programming time: 5ms typical
• Low power dissipation
- 50mA active current
- 20uA standby current
• Two independently Protected sectors
• Package type
- 42 pin plastic DIP
* For page mode read only
MX29L1611G does require high input voltages for programming. Commands require 11V input to determine the operation of the device. Reading data out of the device is similar to reading from an EPROM.
MXIC Flash technology reliably stores memory contents even after 100 cycles. The MXIC's cell is designed to optimize the erase and programming mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling. The MX29L1611G uses a 11V Vpp supply to perform the Auto Erase and Auto Program algorithms.
MXIC's Flash memories augment EPROM functionality with electrical erasure and programming. The MX29L1611G uses a command register to manage this functionality.
P/N:PM0604
The highest degree of latch-up protection is achieved with MXIC's proprietary non-epi process. Latch-up protection is proved for stresses up to 100 milliamps on address and data pin from -1V to VCC +1V.
REV. 0.8, JAN. 24, 2002
1
Page 2
MX29L1611G / MX29L1611*
PIN CONFIGURATIONS
42 PDIP
1
A18
2
A17
3
A7
4
A6
5
A5
6
A4
7
A3
8
A2
9
A1
10
A0
11
CE
12
GND
13
OE
14
Q0 Q8 Q1 Q9 Q2
Q10
Q3
Q11
15 16 17 18 19 20 21
MX29L1611G
PIN DESCRIPTION
SYMBOL PIN NAME
42
A19
41
A8
40
A9
39
A10
38
A11
37
A12
36
A13
35
A14
34
A15
33
A16
32
BYTE/VPP
31
GND
30
Q15/A-1
29
Q7
28
Q14
27
Q6
26
Q13
25
Q5
24
Q12
23
Q4
22
VCC
A0 - A19 Address Input Q0 - Q14 Data Input/Output Q15/A-1 Q15(Word mode)/LSB addr.(Byte
mode, for read mode only) CE Chip Enable Input OE Output Enable Input BYTE/VPP Word/Byte Selection Input, Erase/
Program supply voltage VCC Power Supply GN D Ground Pin
P/N:PM0604
REV. 0.8, JAN. 24, 2002
2
Page 3
BLOCK DIAGRAM
CE
OE
BYTE / VPP
MX29L1611G / MX29L1611*
CONTROL INPUT
LOGIC
PROGRAM/ERASE
HIGH VOLTAGE
WRITE
STATE
MACHINE
(WSM)
Q15/A-1 A0-A19
ADDRESS
LATCH
AND
BUFFER
X-DECODER
MX29L1611G
FLASH ARRA Y
Y-DECODER
Y-PASS GATE
SENSE
AMPLIFIER
Y-select
COMMAND INTERF ACE REGISTER (CIR)
ARRAY
SOURCE
HV
COMMAND
DATA DECODER
PGM
DATA
HV
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
P/N:PM0604
Q0-Q15/A-1
I/O BUFFER
REV. 0.8, JAN. 24, 2002
3
Page 4
MX29L1611G / MX29L1611*
Table1. PIN DESCRIPTIONS
SYMBOL TYPE NAME AND FUNCTION
A0 - A19 INPUT ADDRESS INPUTS: for memory addresses. Addresses are internally latched
during a write cycle.
Q0 - Q7 INPUT/OUTPUT LOW-BYTE DATA BUS: Input data and commands during Command Interface
Register(CIR) write cycles. Outputs array,status and identifier data in the appropriate read mode. Floated when the chip is de-selected or the outputs are disabled.
Q8 - Q14 INPUT/OUTPUT HIGH-BYTE DATA BUS: Inputs data during x 16 Data-Write operations.
Outputs array, identifier data in the appropriate read mode; not used for status register reads. Floated when the chip is de-selected or the outputs are disabled
Q15/A -1 INPUT/OUTPUT Selects between high-byte data INPUT/OUTPUT(BYTE = HIGH) and LSB
ADDRESS(BYTE = LOW) for raed operation.
CE INPUT CHIP ENABLE INPUTS: Activate the device's control logic, Input buffers,
decoders and sense amplifiers. With CE high, the device is deselected and power consumption reduces to Standby level upon completion of any current program or erase operations. CE must be low to select the device.
OE INPUT OUTPUT ENABLES: Gates the device's data through the output buffers during
a read cycle OE is active low.
BYTE/VPP INPUT BYTE ENABLE: While operating read mode, BYTE Low places device in x8
mode. All data is then input or output on Q0-7 and Q8-14 float. AddressQ15/ A-1 selects between the high and low byte. While operating read mode, BYTE high places the device in x16 mode, and turns off the Q15/A-1 input buffer. Address A0, then becomes the lowest order address. ERASE/PROGRAM ENABLE:When BYTE/VPP=11V would place this device
into ERASE/PROGRAM mode. VC C DEVICE POWER SUPPLY(3.3V ± 10%) GND GROUND
P/N:PM0604
REV. 0.8, JAN. 24, 2002
4
Page 5
MX29L1611G / MX29L1611*
BUS OPERATION
Flash memory reads, erases and writes in-system via the local CPU . All bus cycles to or from the flash memory conform to standard microprocessor bus cycles.
Table 2.1 Bus Operations for Word-Wide Mode (BYTE/VPP = VIH)
Mode Notes CE OE BYTE/VPP A0 A1 A9 Q0-Q7 Q8-Q14 Q15/A-1
Read 1 VIL VIL VIH X X X DOUT DOUT DOUT Output Disable 1 VIL VIH VIH X X X High Z High Z HighZ Standby 1 VIH X H/L X X X High Z HIgh Z HighZ Manufacturer ID 2,4 VIL VIL VIH VIL VIL VID C 2H 0 0H 0B Device ID 2,4 VIL VIL VIH VIH VIL VID F 6 H 00 H 0B Write 1,3,5 VIL VIH VPP X X X DIN DIN DIN
Table2.2 Bus Operations for Byte-Wide Mode (BYTE = VIL)
Mode Notes CE OE BYTE/VPP A0 A1 A9 Q0-Q7 Q8-Q14 Q15/A-1
Read 1 VIL VIL VIL X X X DOUT HighZ VIL/VIH Output Disable 1 VIL VIH VIL X X X High Z High Z X Standby 1 VIH X H/L X X X High Z HIgh Z X Manufacturer ID 2,4 VIL VIL VIL VIL VIL VID C 2H High Z VIL Device ID 2,4 VIL VIL VIL VIH VIL VID F 6H High Z VIL Write 1,3,5 VIL VIH VPP X X X D IN DIN DIN
NOTES :
1. X can be VIH or VIL for address or control pins.
2. A0 and A1 at VIL provide manufacturer ID codes. A0 at VIH and A1 at VIL provide device ID codes. A0 at VIL, A1 at VIH and with appropriate sector addresses provide Sector Protect Code.(Refer to Table 4),A2~A19=Do not care.
3. Commands for different Erase operations, Data program operations or Sector Protect operations can only be successfully completed through proper command sequence.
4. VID = 11.5V- 12.5V
5. Word mode only for write operation VPP=10.5V~11.5V
P/N:PM0604
REV. 0.8, JAN. 24, 2002
5
Page 6
WRITE OPERATIONS
MX29L1611G / MX29L1611*
Commands are written to the COMMAND INTERFACE REGISTER (CIR) using standard microprocessor write timings. The CIR serves as the interface between the microprocessor and the internal chip operation. The CIR can decipher Read Array, Read Silicon ID, Erase and Program command. In the event of a read command, the
will only respond to status reads. During a sector/chip erase cycle, the CIR will respond to status reads. After the write state machine has completed its task, it will allow the CIR to respond to its full command set. The CIR stays at read status register mode until the microprocessor issues another valid command sequence.
CIR simply points the read path at either the array or the silicon ID, depending on the specific read command given. For a program or erase cycle, the CIR informs the write state machine that a program or erase has been
Device operations are selected by writing commands into the CIR. Table 3 below defines 16 Mbit flash family command.
requested. During a program cycle, the write state machine will control the program sequences and the CIR
TABLE 3. COMMAND DEFINITIONS(BYTE/VPP=VHH)
Command Read/ Silicon Page Chip Sector Read Clear Sequence Reset ID Read Program Erase Erase Status Reg. Status Reg. Bus Write 4 4 4 6 6 4 3 Cycles Req'd First Bus Addr 5555H 5555H 5555H 5555H 5555H 5555H 5555H Write Cycle Data AAH AAH AAH AAH AAH AAH AAH Second Bus Addr 2AAAH 2AAAH 2AAAH 2AAAH 2AAAH 2AAAH 2AAAH Write Cycle Data 55H 55H 55H 55H 55H 55H 55H Third Bus Addr 5555H 5555H 5555H 5555H 5555H 5555H 5555H Write Cycle Data F 0H 90H A0H 80H 80H 70H 50H Fourth Bus Addr RA 00H/01H PA 5555H 5555H X Read/Write Cycle Data RD C2H/F6H PD AAH AAH SRD Fifth Bus Addr 2AAAH 2AAAH Write Cycle Data 55H 55H Sixth Bus Addr 5555H SA Write Cycle Data 10H 30H
P/N:PM0604
REV. 0.8, JAN. 24, 2002
6
Page 7
MX29L1611G / MX29L1611*
TABLE 3. COMMAND DEFINITIONS
Command Sector Sector Verify Sector Abort Sequence Protection Unprotect Protect Bus Write 6 6 4 3 Cycles Req'd First Bus Addr 5555H 5555H 5555H 5555H Write Cycle Data AAH AAH AAH AAH Second Bus Addr 2AAAH 2AAAH 2AAAH 2AAAH Write Cycle Data 55H 55H 55H 55H Third Bus Addr 5555H 5555H 5555H 5555H Write Cycle Data 60H 60H 90H E0H Fourth Bus Addr 5555H 5555H SA** Read/Write Cycle Data AAH AAH C2H* Fifth Bus Addr 2AAAH 2AAAH Write Cycle Data 55H 55H Sixth Bus Addr SA** SA** Write Cycle Data 20H 40H
Notes:
1. Address bit A15 -- A19 = X = Don't care for all address commands except for Program Address(PA) and Sector Address(SA).
5555H and 2AAAH address command codes stand for Hex number starting from A0 to A14.
2. Bus operations are defined in Table 2.
3. RA = Address of the memory location to be read.
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the CE pulse. SA = Address of the sector to be erased. The combination of A15 -- A19 will uniquely select any sector.
4. RD = Data read from location RA during read operation.
PD = Data to be programmed at location PA. Data is latched on the rising edge of CE. SRD = Data read from status register.
5. Only Q0-Q7 command data is taken, Q8-Q15 = Don't care.
* Refer to Table 4, Figure 11. ** Only the top and the bottom sectors have protect- bit feature. SA = (A19,A18,A17,A16,A15) = 00000B or 11111B is valid.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
7
Page 8
DEVICE OPERATION
SILICON ID READ
MX29L1611G / MX29L1611*
The Silicon ID Read mode allows the reading out of a binary code from the device and will identify its manufacturer and type. This mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its
The manufacturer and device codes may also be read via the command register, for instances when the MX29L1611G is erased or programmed in a system without access to high voltage on the A9 pin. The
command sequence is illustrated in Table 3. corresponding programming algorithm. This mode is functional over the entire temperature range of the device.
Byte 0 (A0=VIL) represents the manfacturer's code
(MXIC=C2H) and byte 1 (A0=VIH) the device identifier
code (MX29L1611G=F6H). To activate this mode, the programming equipment must force VID (11.5V~12.5V) on address pin A9. Two identifier bytes may then be sequenced from the device outputs by toggling address A0 from VIL to VIH. All
To terminate the operation, it is necessary to write the
read/reset command sequence into the CIR. addresses are don't cares except A0 and A1.
Table 4. MX29L1611G Silion ID Codes and Verify Sector Protect Code
Type A19A18A17A16A15A1A0Code(HEX) Q7Q6Q5Q4Q3Q Manufacturer Code X X X X X VIL VIL C2H* 1 1 0 0 0 0 1 0 MX29L1611G Device Code X X X X X VIL VIH F6H* 1 1 1 1 0 1 1 0 Verify Sector Protect Sector Address*** VIH VIL C2H** 1 1 0 0 0 0 1 0
Q1Q
2
0
* MX29L1611G Manufacturer Code = C2H, Device Code = F6H when BYTE/VPP = VIL MX29L1611G Manufacturer Code = 00C2H, Device Code = 00F6H when BYTE/VPP = VIH ** Outputs C2H at protected sector address, 00H at unprotected scetor address. ***Only the top and the bottom sectors have protect-bit feature. Sector address = (A19, A18,A17,A16,A15) = 00000B or 11111B
P/N:PM0604
8
REV. 0.8, JAN. 24, 2002
Page 9
MX29L1611G / MX29L1611*
READ/RESET COMMAND
The read or reset operation is initiated by writing the read/ reset command sequence into the command register. Microprocessor read cycles retrieve array data from the memory. The device remains enabled for reads until the CIR contents are altered by a valid command sequence.
The device will automatically power-up in the read/reset state. In this case, a command sequence is not required for "read operation". Standard microprocessor read cycles will retrieve array data. This default value ensures that no spurious alteration of the memory content occurs during the power transition. Refer to the AC Read Characteristics and Waveforms for the specific timing parameters.
The MX29L1611G is accessed like an EPROM. When CE and OE are low the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever CE or OE is high. This dual line control gives designers flexibility in preventing bus contention.
Note that the read/reset command is not valid when program or erase is in progress.
PAGE READ
The MX29L1611G offers "fast page mode read" function. The users can take the access time advantage if keeping CE, OE at low and the same page address (A3~A19 unchanged). Please refer to Figure 5-2 for detailed timing waveform. The system performance could be enhanced by initiating 1 normal read and 7 fast page reads(for word mode A0~A2) or 15 fast page reads(for byte mode altering A-1~A2).
PAGE PROGRAM
The device is set up in the programming mode when VPP=11V is applied OE=VIH.
command sequence will not start the internal Write State
Machine(WSM), no data will be written to the device.
After three-cycle command sequence is given, a
byte(word) load is performed by applying a low pulse on
the CE input with CE low and OE high. The address is
latched on the falling edge of CE. The data is latched by
the first rising edge of CE. Maximum of 64 words of data
may be loaded into each page by the same procedure as
outlined in the page program section below.
PROGRAM
Any page to be programmed should have the page in the
erased state first, i.e. performing sector erase is suggested
before page programming can be performed.
The device is programmed on a page basis. If a word of
data within a page is to be changed, data for the entire
page can be loaded into the device. Any word that is not
loaded during the programming of its page will be still in
the erased state (i.e. FFH). Once the words of a page
are loaded into the device, they are simultaneously
programmed during the internal programming period.
After the first data word has been loaded into the device,
successive words are entered in the same manner. Each
new word to be programmed must have its high to low
transition on CE within 30us of the low to high transition
of CE of the preceding word. A6 to A19 specify the page
address, i.e., the device is page-aligned on 64 words
boundary. The page address must be valid during each
high to low transition of CE. A0 to A5 specify the word
address withih the page. The word may be loaded in any
order; sequential loading is not required. If a high to low
transition of CE is not detected whithin 100us of the last
low to high transition, the load period will end and the
internal programming period will start. The Auto page
program terminates when status on Q7 is '1' at which time
the device stays at read status register mode until the
CIR contents are altered by a valid command
sequence.(Refer to table 3,6 and Figure 1,7,8)
To initiate Page program mode, a three-cycle command sequence is required. There are two "unlock" write cycles. These are followed by writing the page program command-A0H.
Any attempt to write to the device without the three-cycle
P/N:PM0604
CHIP ERASE
The device is set up in the erase mode when VPP=11V
is applied OE=VIH.
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
REV. 0.8, JAN. 24, 2002
9
Page 10
MX29L1611G / MX29L1611*
"set-up" command-80H. Two more "unlock" write cycles are then followed by the chip erase command-10H.
Chip erase does not require the user to program the device prior to erase.
The automatic erase begins on the rising edge of the last CE pulse in the command sequence and terminates when the status on Q7 is "1" at which time the device stays at read status register mode. The device remains enabled for read status register mode until the CIR contents are altered by a valid command sequence.(Refer to table 3,6 and Figure 2,6,8)
Table 5. MX29L1611G Sector Address Table
(Byte-Wide Mode)
A1 9 A1 8 A 17 A 16 A15 Address Range
[A19, -1]
SA0 0 0 0 0 0 000000H--00FFFFH SA1 0 0 0 0 1 010000H--01FFFFH SA2 0 0 0 1 0 020000H--02FFFFH SA3 0 0 0 1 1 030000H--03FFFFH SA4 0 0 1 0 0 040000H--04FFFFH
.. . .. . ... ... ... ................................
SA31 1 1 1 1 1 1F0000H--1FFFFFH
SECTOR ERASE
Sector erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the set-up command-80H. Two more "unlock" write cycles are then followed by the sector erase command-30H. The sector address is latched on the falling edge of CE, while the command (data) is latched on the rising edge of CE.
Sector erase does not require the user to program the device prior to erase. The system is not required to provide any controls or timings during these operations.
The automatic sector erase begins on the rising edge of the last CE pulse in the command sequence and terminates when the status on Q7 is "1" at which time the device stays at read status register mode. The device remains enabled for read status register mode until the CIR contents are altered by a valid command sequence.(Refer to table 3,6 and Figure 3,4,6,8)
READ STATUS REGISTER
The MXIC's 16 Mbit flash family contains a status
register which may be read to determine when a program
or erase operation is complete, and whether that operation
completed successfully. The status register may be
read at any time by writing the Read Status command to
the CIR. After writing this command, all subsequent read
operations output data from the status register until
another valid command sequence is written to the CIR.
A Read Array command must be written to the CIR to
return to the Read Array mode.
The status register bits are output on Q3 - Q7(table 6)
whether the device is in the byte-wide (x8) or word-wide
(x16) mode for the MX29L1611G. In the word-wide mode
the upper byte, Q(8:15) is set to 00H during a Read Status
command. In the byte-wide mode, Q(8:14) are tri-stated
and Q15/A-1 retains the low order address function.
It should be noted that the contents of the status register
are latched on the falling edge of OE or CE whichever
occurs last in the read cycle. This prevents possible bus
errors which might occur if the contents of the status
register change while reading the status register. CE or
OE must be toggled with each subsequent status read,
or the completion of a program or erase operation will not
be evident.
The Status Register is the interface between the
microprocessor and the Write State Machine (WSM).
When the WSM is active, this register will indicate the
status of the WSM, and will also hold the bits indicating
whether or not the WSM was successful in performing the
desired operation. The WSM sets status bits four
through seven and clears bits six and seven, but cannot
clear status bits four and five. If Erase fail or Program fail
status bit is detected, the Status Register is not cleared
until the Clear Status Register command is written. The
MX29L1611G automatically outputs Status Register data
when read after Chip Erase, Sector Erase, Page Program
or Read Status Command write cycle. The default state
of the Status Register after powerup and return from deep
power-down mode is (Q7, Q6, Q5, Q4) = 1000B. Q3 = 0
or 1 depends on sector-protect status, can not be
changed by Clear Status Register Command or Write
State Machine.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
10
Page 11
MX29L1611G / MX29L1611*
CLEAR STATUS REGISTER
The Eraes fail status bit (Q5) and Program fail status bit (Q4) are set by the write state machine, and can only be reset by the system software. These bits can indicate various failure conditions(see Table 6). By allowing the system software to control the resetting of these bits, several operations may be performed (such as cumulatively programming several pages or erasing multiple blocks in squence). The status register may then be read to determine if an error occurred during that programming or erasure series. This adds flexibility to the way the device may be programmed or erased. Additionally, once the program(erase) fail bit happens, the program (erase) operation can not be performed further. The program(erase) fail bit must be reset by system software before further page program or sector (chip) erase are attempted. To clear the status register, the Clear Status Register command is written to the CIR. Then, any other command may be issued to the CIR. Note again that before a read cycle can be initiated, a Read command must be written to the CIR to specify whether the read data is to come from the Array, Status Register or Silicon ID.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
11
Page 12
MX29L1611G / MX29L1611*
TABLE 6. MX29L1611G STATUS REGISTER
STATUS NOTES Q7 Q6 Q5 Q4 Q3
IN PROGRESS PROGRAM 1,2,5 0 0 0 0 0/1
ERASE 1,3,5 0 0 0 0 0/1
COMPLETE PROGRAM 1,2,5 1 0 0 0 0/1
ERASE 1,3,5 1 0 0 0 0/1
FAIL PROGRAM 1,4,5 1 0 0 1 0/1
ERASE 1,4,5 1 0 1 0 0/1
AFTER CLEARING STATUS REGISTER 5 1 0 0 0 0/1
NOTES:
1. Q7 : WRITE STATE MACHINE STATUS 1 = READY, 0 = BUSY Q5 : ERASE FAIL STATUS 1 = FAIL IN ERASE, 0 = SUCCESSFUL ERASE Q4 : PROGRAM FAIL STATUS 1 = FAIL IN PROGRAM, 0 = SUCCESSFUL PROGRAM Q3 : SECTOR-PROTECT STATUS 1 = SECTOR 0 OR/AND 15 PROTECTED 0 = NONE OF SECTOR PROTECTED Q6,Q2 - 0 = RESERVED FOR FUTURE ENHANCEMENTS. These bits are reserved for future use ; mask them out when polling the Status Register.
2. PROGRAM STATUS is for the status during Page Programming or Sector Unprotect mode.
3. ERASE STATUS is for the status during Sector/Chip Erase or Sector Protection mode.
4. FAIL STATUS bit(Q4 or Q5) is provided during Page Program or Sector/Chip Erase modes respectively.
5. Q3 = 0 or1 depends on Sector-Protect Status.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
12
Page 13
MX29L1611G / MX29L1611*
SECTOR PROTECTION
To activate this mode, a six-bus cycle operation and VPP=11V are required. There are two 'unlock' write cycles. These are followed by writing the 'set-up' command. Two more 'unlock' write cycles are then followed by the Lock Sector command - 20H. Sector address is latched on the falling edge of CE of the sixth cycle of the command sequence. The automatic Lock operation begins on the rising edge of the last CE pulse in the command sequence and terminates when the Status on Q7 is '1' at which time the device stays at the read status register mode.
The device remains enabled for read status register mode until the CIR contents are altered by a valid command sequence (Refer to table 3,6 and Figure 9,11).
VERIFY SECTOR PROTECT
To verify the Protect status of the Top and the Bottom sector, operation is initiated by writing Silicon ID read command into the command register. Following the command write, a read cycle from address XX00H retrieves the Manufacturer code of C2H. A read cycle from XX01H returns the Device code F8H. A read cycle from appropriate address returns information as to which sectors are protected. To terminate the operation, it is necessary to write the read/reset command sequence into the CIR. (Refer to table 3,4 and Figure 11)
A few retries are required if Protect status can not be verified successfully after each operation.
The device remains enabled for read status register mode until the CIR contents are altered by a valid command sequence.
ABORT MODE
To activate Abort mode, a three-bus cycle operation is required. The E0H command (Refer to table 3) only stops Page program or Sector /Chip erase operation currently in progress and puts the device in Abort mode. So the program or erase operation will not be completed. Since the data in some page/sectors is no longer valid due to an incomplete program or erase operation, the program fail (Q4) or erase fail (Q5)bit will be set.
A read array command MUST be written to bring the device out of the abort state without incurring any wake up latency. Note that once device is brought out, Clear status register mode is required before a program or erase operation can be executed.
DATA PROTECTION
The MX29L1611G is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power
transitions. During power up the device automatically
resets the internal state machine in the Read Array mode.
Also, with its control register architecture, alteration of
the memory contents only occurs after successful
completion of specific multi-bus cycle command
sequences.
SECTOR UNPROTECT
It is also possible to unprotect the sector , same as the first five write command cycles in activating sector protection mode followed by the Unprotect Sector command -40H, the automatic Unprotect operation begins on the rising edge of the last CE pulse in the command sequence and terminates when the Status on DQ7 is '1' at which time the device stays at the read status register mode.
(Refer to table 3,6 and Figure 10,11)
P/N:PM0604
The device also incorporates several features to prevent
inadvertent write cycles resulting from VCC power-up
and power-down transitions or system noise.
REV. 0.8, JAN. 24, 2002
13
Page 14
MX29L1611G / MX29L1611*
LOW VCC WRITE INHIBIT
To avoid initiation of a write cycle during VCC power-up and power-down, a write cycle is locked out for VCC less than VLKO(typically 1.8V). If VCC < VLKO, the command register is disabled and all internal program/erase circuits are disabled. Under this condition the device will reset to the read mode. Subsequent writes will be ignored until the VCC level is greater than VLKO. It is the user's responsibility to ensure that the control pins are logically correct to prevent unintentional write when VCC is above VLKO.
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 10ns (typical) on CE will not initiate a write cycle.
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE = VIL,CE = VIH. To initiate a write cycle, CE must be a logical zero while OE is a logical one, and VPP=11V should be applied.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
14
Page 15
MX29L1611G / MX29L1611*
Figure 1. AUTOMATIC PAGE PROGRAM FLOW CHART
START
BYTE/VPP=VHH
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data A0H Address 5555H
Write Program Data/Address
Page Program Completed
YES
Loading End?
YES
Wait 100us
BYTE/VPP=VIH/VIL
Read Status Register
SR7 = 1
?
YES
SR4 = 0
?
YES
Program
another page?
NO
NO
NO
Program Error
To Continue Other Operations,
Do Clear S.R. Mode First
P/N:PM0604
NO
Operation Done, Device Stays At Read S.R. Mode
15
Note : S.R. Stands for Status Register
REV. 0.8, JAN. 24, 2002
Page 16
MX29L1611G / MX29L1611*
Figure 2. AUTOMATIC CHIP ERASE FLOW CHART
START
BYTE/VPP=VHH
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 80H Address 5555H
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 10H Address 5555H
BYTE/VPP=VIH/VIL
Read Status Register
SR7 = 1
?
YES
SR5 = 0
?
YES
Chip Erase Completed
NO
NO
Erase Error
P/N:PM0604
Operation Done,
Device Stays at
Read S.R. Mode
To Continue Other
Operations, Do Clear
S.R. Mode First
REV. 0.8, JAN. 24, 2002
16
Page 17
MX29L1611G / MX29L1611*
Figure 3. AUTOMATIC SECTOR ERASE FLOW CHART
START
BYTE/VPP=VHH
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 80H Address 5555H
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 30H Sector Address
BYTE/VPP=VIH/VIL
Read Status Register
SR7 = 1
?
YES
SR5 = 0
?
YES
Sector Erase Completed
NO
NO
Erase Error
P/N:PM0604
Operation Done,
Device Stays at
Read S.R. Mode
To Continue Other
Operations, Do Clear
S.R. Mode First
REV. 0.8, JAN. 24, 2002
17
Page 18
MX29L1611G / MX29L1611*
ELECTRICAL SPECIFICATIONS
NOTICE:
Stresses greater than those listed under ABSOLUTE
ABSOLUTE MAXIMUM RATINGS
MAXIMUM RATINGS may cause permanent damage to the device. This is stress rating only and functional
RATING VALUE
Ambient Operating Temperature 0°C to 70°C Storage Temperature -65°C to 125°C Applied Input Voltage -0.5V to Vcc+0.5V Applied Output Voltage -0.5V to Vcc+0.6V VCC to Ground Potential -0.5V to 4.0V
operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended period may affect reliability.
NOTICE:
Specifications contained within the following tables are subject to change.
A9 -0.5V to 12.5V BYTE/VPP -0.5V to 11.5V
CAPACITANCE TA = 25
°°
°C, f = 1.0 MHz
°°
SYMBOL PARAMETER MIN. TYP. MAX. UNIT CONDITIONS
CIN Input Capacitance 14 pF VIN = 0V COUT Output Capacitance 16 pF VOUT = 0V
SWITCHING TEST CIRCUITS
DEVICE UNDER TEST
CL = 35 pF Including jig capacitance
SWITCHING TEST WAVEFORMS
2.4V
0.45V
AC TESTING: Inputs are driven at 2.4V for a logic "1" and 0.45V for a logic "0". Input pulse rise and fall times are < 5ns.
INPUT
CL
2.0V
0.8V
6.2K
ohm
TEST POINTS
2.7K
ohm
DIODES = IN3064 OR EQUIVALENT
OUTPUT
3.3V
1.5V
P/N:PM0604
REV. 0.8, JAN. 24, 2002
18
Page 19
MX29L1611G / MX29L1611*
DC CHARACTERISTICS VCC = 3.3V
SYMBOL PARAMETER NOTES MIN. TYP. MAX. UNITS TEST CONDITIONS
IIL Input Load 1 ±1 uA VCC=VCC Max
Current VIN=VCC or GND
ILO Output Leakage 1 ±10 u A VCC=VCC Max
Current VIN=VCC or GND
ISB1 VCC Standby 1 2 0 50 uA VCC=VCC Max
Current(CMOS) CE=VCC ± 0.2V
ISB2 VCC Standby 1 2 mA VCC=VCC Max
Current(TTL) CE=VIH
ICC1 VCC Read 1 5 0 80 mA VCC=VCC Max
Current f=10MHz, IOUT = 0 mA
ICC2 VCC Program 1 15 30 mA Program in Progress
Current ICC3 VCC Erase Current 1 15 30 mA Erase in Progress VIL Input Low Voltage 2 -0.3 0.6 V VIH Input High Voltage 3 0.7xVCC VCC+0.3 V VOL Output Low Voltage 0.45 V IOL=2.1mA, Vcc =Vcc Min VOH Output High Voltage 2.4 V IOH=-100uA, Vcc=Vcc Min
± ±
± 10%
± ±
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at VCC = 3.3V, T = 25°C. These currents are valid for all product versions (package and speeds).
2. VIL min. = -1.0V for pulse width is equal to or less than 50ns.
VIL min. = -2.0V for pulse width is equal to or less than 20ns.
3. VIH max. = VCC + 1.5V for pulse width is equal to oe less than 20ns. If VIH is over the specified maximum value, read operation cannot be guaranteed.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
19
Page 20
MX29L1611G / MX29L1611*
AC CHARACTERISTICS -- READ OPERATIONS
29L1611G-90 29L1611(G)-10 29L1611G-12
SYMBOL DESCRIPTIONS MIN. MAX. MIN. MAX. MIN. MAX. UNIT CONDITIONS
tACC Address to Output Delay 9 0 10 0 12 0 ns CE=OE=VIL tCE CE to Output Delay 9 0 10 0 1 2 0 ns OE=VIL tOE OE to Output Delay 3 0 3 0 30 ns CE=VIL tDF OE High to Output Delay 0 20 0 20 0 20 ns CE=VIL tOH Address to Output hold 0 0 0 ns CE=OE=VIL tBACC BYTE to Output Delay 100 100 120 ns CE= OE=VIL tBHZ BYTE Low to Output in High Z 20 20 2 0 n s CE=VIL
TEST CONDITIONS:
• Input pulse levels: 0.45V/2.4V
• Input rise and fall times: 5ns
• Output load: 1TTL gate + 35pF(Including scope and jig)
• Reference levels for measuring timing: 1.5V
NOTE:
1. tDF is defined as the time at which the output achieves the open circuit condition and data is no longer driven.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
20
Page 21
MX29L1611G / MX29L1611*
Figure 4.1 NORMAL READ TIMING WAVEFORMS
ADDRESSES
CE
OE
DATA OUT
VCC
Vcc
VIH
VIL
VIH
VIL
VIH
VIL
VOH
VOL
3.3V
GND
Power-up
HIGH Z
Standby
Device and address selection
Outputs Enabled
ADDRESSES STABLE
tCE
tACC
tOE
Data valid
Data out valid
Standby
tOH
tDF
Vcc
Power-down
HIGH Z
NOTE:
1. For real world application, BYTE/VPP pin should be either static high(word mode) or static low(byte mode); dynamic switching of BYTE/VPP pin is not recommended.
Figure 4.2 PAGE READ TIMING WAVEFORMS
A3-A19
(A-1), A0~A2
tACC
CE
OE
tOE
DATA OUT
VALID ADDRESS
tPA
tPA
tPA
tOH tDF
P/N:PM0604
REV. 0.8, JAN. 24, 2002
21
Page 22
MX29L1611G / MX29L1611*
Figure 5. BYTE TIMING WAVEFORMS
ADDRESSES
CE
OE
BYTE/VPP
DATA(Q0-Q7)
DATA(Q8-Q15)
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VOH
VOL
VOH
VOL
HIGH Z
HIGH Z
ADDRESSES STABLE
tACC
tCE
tOE
tBACC
tBHZ
Data Output
Data Output
tOH
Data Output
tDF
HIGH Z
HIGH Z
P/N:PM0604
REV. 0.8, JAN. 24, 2002
22
Page 23
MX29L1611G / MX29L1611*
AC CHARACTERISTICS -- WRITE/ERASE/PROGRAM OPERATIONS
29L1611G-90 29L1611(G)-10 29L1611G-12
SYMBOL DESCRIPTION MIN. MAX. MIN. MAX. MIN. MAX. UNIT
tW C Write Cycle Time 9 0 10 0 12 0 ns tAS Address Setup Time 0 0 0 ns tAH Address Hold Time 6 0 60 6 0 ns tDS Data Setup Time 5 0 50 5 0 ns tD H Data Hold Time 1 0 10 1 0 ns tCES CE Setup Time 0 0 0 ns tGHWL Read Recover TimeBefore Write 0 0 0 tWP Write Pulse Width 6 0 60 6 0 ns tWPH Write Pulse Width High 4 0 4 0 4 0 ns tBALC Byte(Word) Address Load Cycle 0.3 30 0.3 30 0.3 30 us tBAL Byte(Word) Address Load Time 10 0 100 10 0 us tSRA Status Register Access Time 120 120 120 ns tCESR CE Setup before S.R. Read 100 1 00 10 0 ns tVCS VCC Setup Time 2 2 2 us tRAW Read Operation Set Up Time After Write 2 0 20 20 ns tVPS VPP Setup Time 2 2 2 us tVPH VPP Hold Time 2 2 2 us
P/N:PM0604
REV. 0.8, JAN. 24, 2002
23
Page 24
MX29L1611G / MX29L1611*
Figure 6. COMMAND WRITE TIMING WAVEFORMS
OE
tWC
CE
ADDRESSES
DATA
VCC
11V
BYTE/VPP
tVCS
tGHWL
HIGH Z
tAS
VALID
tWP
tAH
tDS
tDH
DIN
tWPH
NOTE:
1. BYTE/VPP pin should be static at 11V is equal to or less than during write operation.
2. BYTE/VPP pin should be static at TTL or CMOS level during Read operation.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
24
Page 25
MX29L1611G / MX29L1611*
Figure 7. AUTOMATIC PAGE PROGRAM TIMING WAVEFORMS
A0~A5
A6~A14
A15~A19
CE
OE
BYTE/VPP
DATA
11V
55H
55H
tAS
tAH
tWC
tWP
tVPS
tDS
AAH 55H
tWPH
tDH
AAH
2AH
55H
55H
Word offset Address
Page Address
Last Word offset Address
Page Address
tRAW
Last Write Data
tBAL
tCES
tVPH
tSRA
tBALC
A0H SRD
Write Data
P/N:PM0604
REV. 0.8, JAN. 24, 2002
25
Page 26
MX29L1611G / MX29L1611*
Figure 8. AUTOMATIC SECTOR/CHIP ERASE TIMING WAVEFORMS
A0~A14
A15~A19
CE
OE
BYTE/VPP
DATA
11V
5555H 2AAAH 5555H
tAS
tAH
tWC
tWPH
tWP
tDS
tDH
AAH 55H
80H
5555H
AAH
2AAAH */5555H
SA/*
tCESR
tRAW
55H 30H
tCES
tSRA
SRD
P/N:PM0604
NOTES:
1."*" means "don't care" in this diagram.
2."SA" means "Sector Adddress".
REV. 0.8, JAN. 24, 2002
26
Page 27
MX29L1611G / MX29L1611*
Figure 9. SECTOR PROTECTION ALGORITHM
START,
PLSCNT=0
BYTE/VPP=VHH
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 60H Address 5555H
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 20H, Sector Address*
BYTE/VPP=VIH/VIL
Read Status Register
SR7 = 1
?
YES
Protect Sector
Operation T erminated
To
Verify Protect
Status ?
YES
NO
Verify Protect Status Flow
(Figure 11)
Increment PLSCNT,
To Protect Sector Again
NO
PLSCNT
= 25 ?
NO
Data
= C2H ?
YES
Device Failed
P/N:PM0604
NO
Device Stays at Read S.R. Mode
NOTE : *Only the Top or the Bottom Sector Address is vaild in this feature. i.e. Sector Address = (A19,A18,A17,A16,A15) = 00000B or 11111B
27
YES
Sector Protected,Operation
Done, Device Stays at
Verify Sector Protect Mode
REV. 0.8, JAN. 24, 2002
Page 28
MX29L1611G / MX29L1611*
Figure 10. SECTOR UNPROTECT ALGORITHM
START,
PLSCNT=0
BYTE/VPP=VHH
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 60H Address 5555H
Write Data AAH Address 5555H
Write Data 55H Address 2AAAH
Write Data 40H, Sector Address*
BYTE/VPP=VIH/VIL
Read Status Register
SR7 = 1
?
YES
Unprotect Sector
Operation T erminated
To
Verify Protect
Status ?
YES
NO
Verify Protect Status Flow
(Figure 11)
Increment PLSCNT,
To Unprotect Sector Again
NO
PLSCNT
= 25 ?
NO
Data
= 00H ?
YES
Device Failed
P/N:PM0604
NO
Device Stays at
Read S.R. Mode
NOTE : *Only the Top or the Bottom Sector Address is vaild in this feature. i.e. Sector Address = (A19,A18,A17,A16,A15) = 00000B or 11111B
28
YES
Sector Unprotected,Operation
Done, Device Stays at
Verify Sector Protect Mode
REV. 0.8, JAN. 24, 2002
Page 29
MX29L1611G / MX29L1611*
Figure 11. VERIFY SECTOR PROTECT FLOW CHART
START
BYTE/VPP=VHH
Write Data AAH, Address 5555H
Write Data 55H, Address 2AAAH
Write Data 90H, Address 5555H
BYTE/VPP=VIH/VIL
Protect Status Read*
* 1. Protect Status: Data Outputs C2H as Protected Sector Verified Code. Data Outputs 00H as Unprotected Sector Verified Code.
2. Sepecified address will be either (A19,A18,A17,A16,A15,A1,A0) = (0000010) or (1111110), the rest of the address pins are don't care.
3. Silicon ID can be read via this Flow Chart. Refer to Table 4.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
29
Page 30
MX29L1611G / MX29L1611*
ERASE AND PROGRAMMING PERFORMANCE(1)
LIMITS
PARAMETER MIN. TYP.(2) MAX. UNITS
Chip/Sector Erase Time 20 0 1600 ms Page Programming Time 5 150 ms Chip Programming Time 8 0 240 sec Erase/Program Cycles 1 00 Cycles
Note: (1).Sampled, not 100% tested. Excludes external system level over head. (2).Typing values are measured at 25°C, noninal voltage
LATCHUP CHARACTERISTICS
MIN. MAX.
Input Voltage with respect to GND on all pins except I/O pins -1.0V 6.6V Input Voltage with respect to GND on all I/O pins -1.0V Vcc + 1.0V Current -100mA +100mA Includes all pins except Vcc. Test conditions: Vcc = 3.3V, one pin at a time.
P/N:PM0604
REV. 0.8, JAN. 24, 2002
30
Page 31
MX29L1611G / MX29L1611*
ORDER INFORMATION
PLASTIC PACKAGE
PART NO. Access Time Operating Current Standby Current PACKAGE
(ns) MAX.(mA) MAX.(uA)
MX29L1611GPC-90 90 8 0 20 42 PDIP MX29L1611GPC-10 100 8 0 2 0 42 PDIP MX29L1611GPC-12 120 8 0 2 0 42 PDIP MX29L1611PC-90 90 8 0 2 0 42 PDIP MX29L1611PC-10 100 8 0 2 0 42 PDIP MX29L1611PC-12 120 8 0 2 0 42 PDIP
P/N:PM0604
REV. 0.8, JAN. 24, 2002
31
Page 32
PACKAGE INFORMATION
42-PIN PLASTIC DIP(600 mil)
MX29L1611G / MX29L1611*
P/N:PM0604
REV. 0.8, JAN. 24, 2002
32
Page 33
MX29L1611G / MX29L1611*
REVISION HISTORY
Revision Description Page Date
0.2 Erase/programming operation voltage change(10V-->11V) P1,4,9,14,25 Mar/15/1999 P26,27
Modify Bus operation P5 Modify command definitions P6 Modify "Automatic page program time waveforms" P26 Modify "Sector Protection Algorithm" P28 Modify "Sector unprotect Algorithm" P29 Modify "Erase and programming performance" P31
0.3 Description correction P1,6,7,9,13,19 MAR/23/1999 P22,23
Plug in BYTE/VPP operation description P15,16,17,18,28,29,30
0.4 Delete Page mode operation P1,9,20,22 MAY/07/1999
Delete Erase suspard/resume operation P6,10,12,16,17,19 Modify description P1,2 Undate Erase and Program Performance P30
0.5 Change Fast random access time:100ns-->90ns P1 APR/07/2000
Change 29L1611G-10-->29L1611G-90 P20 tACC:100-->90, tCE:100-->90 Change Verify Protect Status Flow(Figure 12)-->(Figure 11) P27,28
0.6 Modify AC Characteristics 29L1611G-10-->29L1611G-90 ; P23 APR/18/2000
tWC:120-->90 P23
0.7 Correct ID Binay Code from 1000 to 0110 P8 JUL/10/2001
Modify Package Information P31
0.8 1.Add Page Read 30ns P1 JAN/24/2002
2.Add Page Read P9
3.Add 29L1611(G)-10 P20
4.Add Page Read Timing Waveform P21
5.Add 29L1611(G)-10 P23
6.Add Order Information P31
P/N:PM0604
REV. 0.8, JAN. 24, 2002
33
Page 34
MX29L1611G / MX29L1611*
MACRONIX INTERNATIONAL CO., LTD.
HEADQUARTERS:
TEL:+886-3-578-6688 FAX:+886-3-563-2888
EUROPE OFFICE:
TEL:+32-2-456-8020 FAX:+32-2-456-8021
JAPAN OFFICE:
TEL:+81-44-246-9100 FAX:+81-44-246-9105
SINGAPORE OFFICE:
TEL:+65-348-8385 FAX:+65-348-8096
TA IPEI OFFICE:
TEL:+886-2-2509-3300 FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-453-8088 FAX:+1-408-453-8488
CHICAGO OFFICE:
TEL:+1-847-963-1900 FAX:+1-847-963-1909
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
Loading...