Datasheet MT9161BE, MT9161BN, MT9160BN, MT9161BS Datasheet (MITEL)

ISO

2

-CMOS

MT9160B/61B

5 Volt Multi-Featured Codec (MFC)

Advance Information

Features

• Improved idle channel noise over MT9160

• MT9161 version features a delayed framing
pulse in SSI and ST-BUS modes to facilitate
cascaded devices

• Programmable µ-Law/A-Law Codec and Filters

• Programmable ITU-T G.711/sign-magnitude
coding

• Programmable transmit, receive and side-tone
gains

• Fully differential interface to handset
transducers - including 300 ohm receiver driver

• Flexible digital interface including ST-BUS/SSI

• Serial microport or default controllerless mode

• Single 5 volt supply

• Low power operation

• ITU-T G.714 compliant

Applications

• Digital telephone sets

• Cellular radio sets

• Local area communications stations

DS5145 ISSUE 3 March 1999

Ordering Information

MT9161BE 24 Pin Plastic DIP(600 mil)
MT9160BE 24 Pin Plastic DIP(600 mil)
MT9161BS 24 Pin SOIC
MT9160BS 20 Pin SOIC
MT9161BN 24 Pin SSOP
MT9160BN 20 Pin SSOP

-40°C to +85°C

Description

The MT9160B/61B 5V Multi-featured Codec
incorporates a built-in Filter/Codec, gain control and
programmable sidetone path as well as on-chip
anti-alias filters, reference voltage and bias source.
The device supports both ITU-T and sign-magnitude
A-Law and µ-Law requirements.

Complete telephony interfaces are provided for
connection to handset transducers. Internal register
access is provided through a serial microport
compatible with various industry standard
micro-controllers. The device also supports
controllerless operation utilizing the default register
conditions.

The MT9160B/61B is fabricated in Mitel's
ISO2-CMOS technology ensuring low power
consumption and high reliability.

VSSD

VDD

VSSA

VBias

VRef

Din

Dout

STB/F0i

CLOCKin

STBd/FOod

(MT9161B only)

Flexible

Digital

Interface

FILTER/CODEC GAIN

ST-BUS

Channels

PWRST

ENCODER
DECODER

Timing

C & D

IC

7dB

-7dB

Serial Microport

CS DATA1 DATA2 SCLK

Figure 1 - Functional Block Diagram

Transducer

Interface

M ­M +

HSPKR +
HSPKR -

A/µ/IRQ

79

MT9160B/61B Advance Information

MT9160BE MT9161BE/BS/BN

VBias

VRef

NC

PWRST
A/µ/IRQ

VSSD

CS
NC

SCLK
DATA1
DATA2

1
2

3
4
5

IC

6
7
8

9
10
11
12

24 PIN PDIP/SOIC/SSOP

IC

CS

1
2

3
4
5

6
7
8

9
10
11
12

24 PIN PDIP

24
23
22
21
20
19
18
17
16
15
14
13

M +
M ­VSSA
NC
HSPKR +
HSPKR ­VDD
CLOCKin
NC

F0i

STB/
Din
Dout

24
23
22
21
20
19
18
17
16
15
14
13

M +
M ­VSSA
NC
HSPKR +
HSPKR ­VDD
CLOCKin
STBd/
STB/
Din
Dout

VBias

VRef

PWRST

IC

µ/IRQ

A/

VSSD

CS

SCLK
DATA1
DATA2

MT9160BS/BN

10

1
2

3
4
5

6
7
8
9

20
19
18
17
16
15
14
13
12
11

20 PIN SOIC/SSOP

M +
M ­VSSA

HSPKR +

HSPKR ­VDD
CLOCKin
STB/F0i
Din
Dout

VBias

VRef

NC

PWRST

A/µ/IRQ

VSSD

NC

SCLK
DATA1
DATA2

Figure 2 - Pin Connections

Pin Description

Pin #
20 Pin

Pin #
24 Pin

11V

22 V

Name Description

Bias

Ref

Bias Voltage (Output). (VDD/2) volts is available at this pin for biasing external
amplifiers. Connect 0.1 µF capacitor to V

Connect 1 µF capacitor to Vref.

SSA,

Reference Voltage for Codec (Output). Nominally [(VDD/2)-1.9] volts. Used
internally. Connect 0.1 µF capacitor to V

Connect 1 µF capacitor to VBias.

SSA,

34PWRST Power-up Reset (Input). CMOS compatible input with Schmitt Trigger (active low).

Resets internal state of device.

FOod

F0i

45 ICInternal Connection. Tie externally to V

for normal operation.

SSD

56A/µ/IRQ A/µ - When internal control bit DEn = 0 this CMOS level compatible input pin

governs the companding law used by the filter/Codec;µ-Law when tied to V

SSD

and
A-Law when tied to VDD. Logically OR’ed with A/µ register bit.
IRQ - When internal control bit DEn = 1 this pin becomes an open-drain interrupt
output signalling valid access to the D-Channel registers in ST-BUS mode.

67V

SSD

Digital Ground. Nominally 0 volts.

78 CS Chip Select (Input). This input signal is used to select the device for microport

data transfers. Active low. CMOS level compatible.

8 10 SCLK Serial Port Synchronous Clock (Input). Data clock for microport. CMOS level

compatible.

9 11 DATA 1 Bidirectional Serial Data. Port for microprocessor serial data transfer. In Motorola/

National mode of operation, this pin becomes the data transmit pin only and data
receive is performed on the DATA 2 pin. Input CMOS level compatible.

10 12 DATA 2 Serial Data Receive. In Motorola/National mode of operation, this pin is used for

data receive. In Intel mode, serial data transmit and receive are performed on the
DATA 1 pin and DATA 2 is disconnected. Input CMOS level compatible.

11 13 D

out

Data Output. A high impedance three-state digital output for 8 bit wide channel
data being sent to the Layer 1 transceiv er. Data is shifted out via this pin concurrent
with the rising edge of the bit clock during the timeslot defined by STB, or according
to standard ST-BUS timing.

12 14 D

80

Data Input. A digital input for 8 bit wide channel data received from the Layer 1

in

transceiver. Data is sampled on the falling edge of the bit clock during the timeslot
defined by STB, or according to standard ST-BUS timing. Input level is CMOS
compatible.

Advance Information MT9160B/61B

Pin Description (continued)

Pin #
20 Pin

Pin #
24 Pin

13 15 STB/F0i Data Strobe/Frame Pulse (Input). For SSI mode this input determines the 8 bit

16

(MT9161B

only)

14 17 CLOCKin Clock (Input). The clock provided to this input pin is used for the internal device

15 18 V
16 19 HSPKR- Inverting Handset Speaker (Output). Output to the handset speaker (balanced).
17 20 HSPKR+ Non-Inverting Handset Speaker (Output). Output to the handset speaker

18 22 V
19 23 M- Inverting Microphone (Input). Inverting input to microphone amplifier from the

Name Description

timeslot used by the device for both transmit and receive data. This active high
signal has a repetition rate of 8 kHz. Standard frame pulse definitions apply in
ST-BUS mode (refer to figure 11). CMOS level compatible input.

STBd/

FOod

DD

SSA

Delayed Frame Pulse Output. In SSI mode, an 8 bit wide strobe is output after the
first strobe goes low. In ST-BUS mode, a frame pulse is output 4 channel time slots
after /F0i.

functions. For SSI mode connect the bit clock to this pin when it is 512 kHz or
greater. Connect a 4096 kHz clock to this input when the available bit clock is 128
kHz or 256 kHz. For ST-BUS mode connect C4i to this pin. CMOS level compatible.

Positive Power Supply (Input). Nominally 5 volts.

(balanced).
Analog Ground (Input). Nominally 0 volts.

handset microphone.

20 24 M+ Non-Inverting Microphone (Input). Non-inverting input to microphone amplifier

from the handset microphone.

3,9,

16,21

Overview

The 5V Multi-featured Codec (MFC) features
complete Analog/Digital and Digital/Analog
conversion of audio signals (Filter/Codec) and an
analog interface to a standard handset transmitter
and receiver (Transducer Interface). The receiver
amplifier is capable of driving a 300 ohm load.

Each of the programmable parameters within the
functional blocks is accessed through a serial
microcontroller port compatible with Intel MCS-51®,
Motorola SPI® and National Semiconductor
Microwire® specifications. These parameters
include: gain control, power down, mute, B-Channel
select (ST-BUS mode), C&D channel control/access,
law control, digital interface programming and
loopback. Optionally the device may be used in a
controllerless mode utilizing the power-on default
settings.

NC No Connect. (24 Pin Packages only). Pin 16 is NC for MT9160B.

Functional Description

Filter/Codec

The Filter/Codec block implements conversion of the
analog 0-3.3 kHz speech signals to/from the digital
domain compatible with 64 kb/s PCM B-Channels.
Selection of companding curves and digital code
assignment are programmable. These are ITU-T
G.711 A-law or µ-Law, with true-sign/Alternate Digit
Inversion or true-sign/Inverted Magnitude coding,
respectively. Optionally, sign-magnitude coding may
also be selected for proprietary applications.

The Filter/Codec block also implements transmit and
receive audio path gains in the analog domain. A
programmable gain, voice side-tone path is also
included to provide proportional transmit speech
feedback to the handset receiver. This side tone path
feature is disabled by default. Figure 3 depicts the
nominal half-channel and side-tone gains for the
MT9160B/61B.

81

MT9160B/61B Advance Information

In the event of PWRST, the MT9160B/61B defaults
such that the side-tone path is off, all programmable
gains are set to 0dB and ITU-T µ-Law is selected.
Further, the digital port is set to SSI mode operation
at 2048 kb/s and the FDI and driver sections are
powered up. (See Microport section)

The internal architecture is fully differential to provide
the best possible noise rejection as well as to allow a
wide dynamic range from a single 5 volt supply
design. This fully differential architecture is
continued into the Transducer Interface section to
provide full chip realization of these capabilities for
the handset functions.

A reference voltage (V

), for the conversion

Ref

requirements of the Codec section, and a bias
voltage (V
sections, are both generated on-chip. V

), for biasing the internal analog

Bias

Bias

is also
brought to an external pin so that it may be used for
biasing external gain setting amplifiers. A 0.1µF
capacitor must be connected from V
ground at all times. Although V

may only be used

Ref

to analog

Bias

internally, a 0.1µF capacitor must be connected from
V

to ground. The analog ground reference point

Ref

for these two capacitors must be physically the same
point. Connect a 1µF capacitor between V
V

to ensure a quiet reference voltage. To facilitate

Ref

this the V

Ref

and V

pins are situated on adjacent

Bias

Bias

and

pins.

Register 1 (address 00h). Transmit filter gain is
adjustable from 0 dB to +7 dB and receive filter gain
from 0dB to -7 dB, both in 1 dB increments.

Side-tone filter gain is controlled by the STG0-STG
control bits located in Gain Control Register 2
(address 01h). Side-tone gain is adjustable from

-9.96 dB to +9.96 dB in 3.32 dB increments.

Companding law selection for the Filter/Codec is
provided by the A/µ companding control bit while the
coding scheme is controlled by the Smag/ITU-T
control bit. The A/µ control bit is logically OR’ed with
the A/µ pin providing access in both controller and
controllerless modes. Both A/µ and Smag/ITU-T
reside in Control Register 2 (address 04h). Table 1
illustrates these choices.

Code

+ Full Scale 1111 1111 1000 0000 1010 1010

+ Zero 1000 0000 1111 1111 1101 0101

-Zero

(quiet code)

- Full Scale 0111 1111 0000 0000 0010 1010

Sign/

Magnitude

0000 0000 0111 1111 0101 0101

ITU-T (G.711)

µ-Law A-Law

Table 1 - PCM Coding

Transducer Interfaces

2

The transmit filter is designed to meet ITU-T G.714
specifications. The nominal gain for this filter is 0 dB
(gain control = 0 dB). Gain control allows the output
signal to be increased up to 7 dB. An anti-aliasing
filter is included. This is a second order lowpass
implementation with a corner frequency at 25 kHz.

The receive filter is designed to meet ITU-T G.714
specifications. The nominal gain for this filter is 0 dB
(gain control = 0dB). Gain control allows the output
signal to be attenuated up to 7 dB. Filter response is
peaked to compensate for the sinx/x attenuation
caused by the 8 kHz sampling rate.

Side-tone is derived from the input of the Tx filter and
is not subject to the gain control of the Tx filter
section. Side-tone is summed into the receive
handset transducer driver path after the Rx filter gain
control section so that Rx gain adjustment will not
affect side-tone levels. The side-tone path may be
enabled/disabled with the gain control bits located in
Gain Control Register 2 (address 01h).

Transmit and receive filter gains are controlled by the
TxFG0-TxFG2 and RxFG0-RxFG2 control bits,
respectively. These are located in Gain Control

Standard handset transducer interfaces are provided
by the MT9160B/61B. These are:

• The handset microphone inputs (transmitter),
pins M+/M-. The transmit path gain path may be
adjusted to either 6.0 dB or 15.3 dB. Control of
this gain is provided by the TxINC control bit
(Gain Control register 1, address 00h).

• The handset speaker outputs (receiver), pins
HSPKR+/HSPKR-.This internally compensated
fully differential output driver is capable of driving
the load shown in Figure 3. The nominal receive
path gain may be adjusted to either 0 dB, -6 dB or

-12 dB. Control of this gain is provided by the
RxINC control bit (Gain Control register 1,
address 00h). This gain adjustment is in addition
to the programmable gain provided by the receive
filter.

The serial microport, compatible with Intel MCS-51
(mode 0), Motorola SPI (CPOL=0,CPHA=0) and
National Semiconductor Microwire specifications
provides access to all MT9160B/61B internal read
and write registers. This microport consists of a
transmit/receive data pin (DATA1), a receive data pin

82

Advance Information MT9160B/61B

Serial

PCM

D

Port

in

PCM

D

out

Decoder

2.05dB

Encoder

-2.05dB

Filter/Codec and Transducer Interface

Default Bypass

Receive

Filter Gain

0 to -7 dB

(1 dB steps)

Transmit Filter

Transmit Filter

Gain

Gain

0 to +7 dB

0 to +7 dB

(1 dB steps)

(1 dB steps)

INTERNAL TO DEVICE

-0.37 dB or 8.93 dB

-6 dB

Side-tone

-9.96 to

+9. 96 dB

(3.32 dB steps)

-11 dB

Transmit Gain

-8.05 dB or

-2.05 dB
Receiver

Driver

Default Side-tone off

Transmit

Gain

8.42 dB

HSPKR +

75Ω

HSPKR -

75Ω

M+

Transmitter

Microphone

M-

EXTERNAL TO DEVICE

Handset

Receiver

(150Ω)

Figure 3 - Audio Gain Partitioning

(DATA2), a chip select pin (CS) and a synchronous
data clock pin (SCLK). For D-channel contention
control, in ST-BUS mode, this interface provides an
open-drain interrupt output (IRQ).

The microport dynamically senses the state of the
serial clock (SCLK) each time chip select becomes
active. The device then automatically adjusts its
internal timing and pin configuration to conform to
Intel or Motorola/National requirements. If SCLK is
high during chip select activation then Intel mode 0
timing is assumed. The DATA1 pin is defined as a
bi-directional (transmit/receive) serial port and
DATA2 is internally disconnected. If SCLK is low
during chip select activation then Motorola/National
timing is assumed. Motorola processor mode
CPOL=0, CPHA=0 must be used. DATA1 is defined
as the data transmit pin while DATA2 becomes the
data receive pin. Although the dual port Motorola
controller configuration usually supports full-duplex
communication, only half-duplex communication is
possible in the MT9160B/61B. The micro must
discard non-valid data which it clocks in during a
valid write transfer to the MT9160B/61B. During a
valid read transfer from the MT9160B/61B data
simultaneously clocked out by the micro is ignored
by the MT9160B/61B.

All data transfers through the microport are two-byte
transfers requiring the transmission of a Command/
Address byte followed by the data byte written or
read from the addressed register. CS must remain
asserted for the duration of this two-byte transfer. As
shown in Figures 5 and 6 the falling edge of CS
indicates to the MT9160B/61B that a microport
transfer is about to begin. The first 8 clock cycles of
SCLK after the falling edge of CS are always used to
receive the Command/Address byte from the
microcontroller. The Command/Address byte
contains information detailing whether the second
byte transfer will be a read or a write operation and
at what address. The next 8 clock cycles are used to
transfer the data byte between the MT9160B/61B
and the microcontroller. At the end of the two-byte
transfer CS is brought high again to terminate the
session. The rising edge of CS will tri-state the
output driver of DATA1 which will remain tr i-stated as
long as CS is high.

Intel processors utilize least significant bit first
transmission while Motorola/National processors
employ most significant bit first transmission. The
MT9160B/61B microport automatically
accommodates these two schemes for normal data
bytes. However, to ensure decoding of the R/W and
address information, the Command/Address byte is
defined differently for Intel operation than it is for

83

MT9160B/61B Advance Information

Motorola/National operation. Refer to the relative

Flexible Digital Interface

timing diagrams of Figures 5 and 6.

A serial link is required to transport data between the
Receive data is sampled on the rising edge of SCLK
while transmit data is made available concurrent with
the falling edge of SCLK.

COMMAND/ADDRESS DATA INPUT/OUTPUT COMMAND/ADDRESS:

DATA 1
RECEIVE

DATA 1
TRANSMIT

SCLK

CS

➀ Delays due to internal processor timing which are transparent.
② The MT9160:-latches received data on the rising edge of SCLK.

➂ The falling edge of

subsequent byte is always data until terminated via

➃ A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again.
➄ The COMMAND/ADDRESS byte contains:

D0D1D2D3D4D5D6D

②

➂

-outputs transmit data on the falling edge of SCLK.
CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The

➄

➀

D

7

0D1D2D3D4D5D6D7

D0D1D2D3D4D5D6D

CS returning high.

1 bit - Read/
3 bits - Addressing Data
4 bits - Unused

Write

MT9160B/61B and an external digital transmission
device. The MT9160B/61B utilizes the ST-BUS
architecture defined by Mitel Semiconductor but also

7

D

7

XX A2A1A

➀

➃

➂

➃

D0D1D2D3D4D5D6D

D0D1D2D3D4D5D6D

XX

7

7

D

0

R/W

0

Figure 4 - Serial Port Relative Timing for Intel Mode 0

COMMAND/ADDRESS DATA INPUT/OUTPUT COMMAND/ADDRESS:

DATA 2
RECEIVE

DATA 1
TRANSMIT

SCLK

CS

➀ Delays due to internal processor timing which are transparent.
② The MT9160:-latches received data on the rising edge of SCLK.

➂ The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The

subsequent byte is always data until terminated via

➃ A new COMMAND/ADDRESS byte may be loaded only by
➄ The COMMAND/ADDRESS byte contains:

D7D6D5D4D3D2D1D

②

➂

-outputs transmit data on the falling edge of SCLK.

➄

➀

D7D6D5D4D3D2D1D

0

D7D6D5D4D3D2D1D

CS returning high.

1 bit - Read/
3 bits - Addressing Data
4 bits - Unused

Write

0

0

➃

CS cycling high then low again.

D

7

R/WX A1A

➀

➃

D7D6D5D4D3D2D1D

D7D6D5D4D3D2D1D

➂

XX

A

2

0

0

D

0

X

0

84

Figure 5 - Serial Port Relative Timing for Motorola Mode 00/National Microwire

Advance Information MT9160B/61B

125 µs

F0i

DSTi,
DSTo

F0od

CHANNEL 0
D-channel

LSB first

for D-

Channel

CHANNEL 1
C-channel

CHANNEL 2
B1-channel

MSB first for C, B1- & B2-

Channels

CHANNEL 3
B2-channel

Figure 6 - ST-BUS Channel Assignment

supports a strobed data interface found on many
standard Codec devices. This interface is commonly
referred to as Simple Serial Interface (SSI). The
combination of ST-BUS and SSI provides a Flexible
Digital Interface (FDI) capable of supporting all Mitel
basic rate transmission devices as well as many
other 2B+D transceivers.

The required mode of operation is selected via the
CSL2-0 control bits (Control Register 2, address
04h). Pin definitions alter dependent upon the
operational mode selected, as described in the
following subsections as well as in the Pin
Description tables.

Quiet Code
The FDI can be made to send quiet code to the

decoder and receive filter path by setting the RxMute
bit high. Likewise, the FDI will send quiet code in the
transmit path when the TxMute bit is high. Both of
these control bits reside in Control Register 1 at
address 03h. When either of these bits are low their
respective paths function normally. The -Zero entry
of Table 1 is used for the quiet code definition.

ST-BUS Mode
The ST-BUS consists of output (DSTo) and input

(DSTi) serial data streams, in FDI these are named
Dout and Din respectively, a synchronous clock input
signal CLOCKin (C4i), and a framing pulse input
(F0i). These signals are direct connections to the
corresponding pins of Mitel basic rate devices. The
CSL2, CSL1 and CSL0 bits are set to 1 for ST-BUS
operation.

The data streams operate at 2048 kb/s and are Time
Division Multiplexed into 32 identical channels of 64
kb/s bandwidth. A frame pulse (a 244 nSec low going
pulse) is used to separate the continuous serial data
streams into the 32 channel TDM frames. Each
frame has a 125 µSecond period translating into an 8
kHz frame rate. A valid frame begins when F0i is

CHANNELS 4-31

Not Used

logic low coincident with a falling edge of C4i. R efer
to figure 11 for detailed ST-BUS timing. C4i has a
frequency (4096 kHz) which is twice the data rate.
This clock is used to sample the data at the 3/4
bit-cell position on DSTi and to make data available
on DSTo at the start of the bit-cell. C4i is also used to
clock the MT9160B/61B internal functions (i.e.,
Filter/Codec, Digital gain and tone generation) and to
provide the channel timing requirements.

The MT9160B/61B uses only the first four channels
of the 32 channel frame. These channels are always
defined, beginning with Channel 0 after the frame
pulse, as shown in Figure 6 (ST-BUS channel
assignments). The MT9161B provides a delayed
frame pulse (F0od), 4 channels after the input frame
pulse.

The first two (D & C) Channels are enabled for use
by the DEN and CEN bits respectively, (Control
Register 2, address 04h). ISDN basic rate service
(2B+D) defines a 16 kb/s signalling (D) Channel. The
MT9160B/61B supports transparent access to this
signalling channel. ST-BUS basic rate transmission
devices, which may not employ a microport, provide
access to their internal control/status registers
through the ST-BUS Control (C) Channel. The
MT9160B/61B supports microport access to this
C-Channel.

DEN - D-Channel

In ST-BUS mode access to the D-Channel (transmit
and receive) data is provided through an 8-bit read/
write register (address 06h). D-Channel data is
accumulated in, or transmitted from this register at
the rate of 2 bits/frame for 16 kb/s operation (1 bit/
frame for 8 kb/s operation). Since the ST-BUS is
asynchronous, with respect to the microport, valid
access to this register is controlled through the use
of an interrupt (IRQ) output. D-Channel access is
enabled via the (DEn) bit.

85

MT9160B/61B Advance Information

DEN:

When 1, ST-BUS D-channel data (1 or 2 bits/frame
depending on the state of the D8 bit) is shifted into/
out of the D-channel (READ/WRITE) register.

When 0, the receive D-channel data (READ) is still
shifted into the proper register while the DSTo
D-channel timeslot and IRQ outputs are tri-stated
(default).

D8:

When 1, D-Channel data is shifted at the rate of 1 bit/
frame (8 kb/s).

When 0, D-Channel data is shifted at the rate of 2
bits/frame (16 kb/s default).

16 kb/s D-Channel operation is the default mode
which allows the microprocessor access to a full byte
of D-Channel information every fourth ST-BUS
frame. By arbitrarily assigning ST-BUS frame n as
the reference frame, during which the
microprocessor D-Channel read and write operations
are performed, then:

(a) A microport read of address 04 hex will result in a
byte of data being extracted which is composed of
four di-bits (designated by roman numerals I,II,III,IV).
These di-bits are composed of the two D-Channel
bits received during each of frames n, n-1, n-2 and
n-3. Referring to Fig. 7a: di-bit I is mapped from
frame n-3, di-bit II is mapped from frame n-2, di-bit III
is mapped from frame n-1 and di-bit IV is mapped
from frame n.

An interrupt output is provided (IRQ) to synchronize
microprocessor access to the D-Channel register
during valid ST-BUS periods only. IRQ will occur
every fourth (eighth in 8 kb/s mode) ST-BUS frame at
the beginning of the third (second in 8 kb/s mode)
ST-BUS bit cell period. The interrupt will be removed
following a microprocessor Read or Write of Address
04 hex or upon encountering the following fr amesF0i
input, whichever occurs first. To ensure D-Channel
data integrity, microport read/write access to
Address 04 hex must occur before the following
frame pulse. See Figure 7b for timing.

8 kb/s operation expands the interrupt to every eight
frames and processes data one-bit-per-frame.
D-Channel register data is mapped according to
Figure 7c.

Cen - C-Channel

Channel 1 conveys the control/status information for
the Layer 1 transceiver. C-Channel data is
transferred MSB first on the ST-BUS by the
MT9160B/61B. The full 64 kb/s bandwidth is
available and is assigned according to which
transceiver is being used. Consult the data sheet for
the selected transceiver for its C-Channel bit
definitions and order of bit transfer.

When CEN is high, data written to the C-Channel
register (address 05h) is transmitted, most
significant bit first, on DSTo. On power-up reset
(PWRST) or software reset (Rst, address 03h) all
C-Channel bits default to logic high. Receive
C-Channel data (DSTi) is always routed to the read
register regardless of this control bit's logic state.

The D-Channel read register is not preset to any
particular value on power-up (PWRST) or software
reset (RST).

(b) A microport write to Address 04 hex will result in
a byte of data being loaded which is composed of
four di-bits (designated by roman numerals I, II, III,
IV). These di-bits are destined for the two D-Channel
bits transmitted during each of frames n+1, n+2, n+3,
n+4. Referring to Fig. 7a: di-bit I is mapped to frame
n+1, di-bit II is mapped to frame n+2, di bit III is
mapped to frame n+3 and di bit IV is mapped to
frame n+4.

If no new data is written to address 04 hex, the
current D-channel register contents will be
continuously re-transmitted. The D-Channel write
register is preset to all ones on power-up (PWRST)
or software reset (RST).

86

When low, data transmission is halted and this
timeslot is tri-stated on DSTo.

B1-Channel and B2-Channel

Channels 2 and 3 are the B1 and B2 channels,
respectively. B-channel PCM associated with the
Filter/Codec and transducer audio paths is selected
on an independent basis for the transmit and receive
paths. TxBSel and RxBSel (Control Register 1,
address 03h) are used for this purpose.

If no valid transmit path has been selected then the
timeslot output on DSTo is tr i-stated (see PDFDI and
PDDR control bits, Control Register 1 address 03h).

Advance Information MT9160B/61B

IRQ

Microport Read/Write Access

FP

DSTo/
DSTi

n-3 n-2 n-1 n n+1 n+2 n+3 n+4*

Di-bit Group
Receive
D-Channel

D0

I

D2

II

D1

No preset value

D3

D4

III

D5

* note that frame n+4 is equivalent to frame n of the next cycle.

Figure 7a - D-Channel 16 kb/s Operation

FP

C4i

C2

DSTo/
DSTi

IRQ

D0

8 kb/s operation

D1

16 kb/s operation

IV

D6

D7

Di-bit Group

Transmit

D-Channel

tif=500 nsec max

Microport Read/Write Access

D0

I

D1

D2

II

D3

D4

III

D5

D6

IV

D7

Power-up reset to 1111 1111

tir=500 nsec max

= 10 k

R

pullup

Reset coincident with

Read/Write of Address 04 Hex

or next

FP, whichever occurs first

IRQ

FP

Di-bit Group
Receive
D-Channel

Figure 7b - IRQ Timing Diagram

n-7 n-6 n-5 n-4 n-3 n-2 n-1 n n+1

IID1IIID2IV

I

D0

No preset value

D3

V

D4

VID5VIID6VIII

D7

Di-bit Group

Transmit

D-Channel

Figure 7c - D-Channel 8 kb/s Operation

Microport Read/Write Access

I

D0

n+2

IID1IIID2IV

n+3

n+4

D3

Power-up reset to 1111 1111

n+5

VID5VIID6VIII

V

D4

n+6

n+7

n+8

D-Channel

D7

87

MT9160B/61B Advance Information

SSI Mode

The SSI BUS consists of input and output serial data
streams named Din and Dout respectively, a Clock
input signal (CLOCKin), a framing strobe input (STB)
and the MT9161B provides a delayed framing strobe
output (STBd). The frame strobe must be
synchronous with, and eight cycles of, the bit clock.
A 4.096 MHz master clock is also required for SSI
operation if the bit clock is less than 512 kHz. The
timing requirements for SSI are shown in Figures 12
& 13.

In SSI mode the MT9160B/61B supports only
B-Channel operation. The internal C and D Channel
registers used in ST-BUS mode are not functional for
SSI operation. The control bits TxBSel and RxBSel,
as described in the ST-BUS section, are ignored
since the B-Channel timeslot is defined by the input
STB strobe. Hence, in SSI mode transmit and
receive B-Channel data are always in the channel
defined by the STB input.

The data strobe input STB determines the 8-bit
timeslot used by the device for both transmit and
receive data. This is an active high signal with an 8
kHz repetition rate.The MT9161B provides a delayed
strobe pulse (STBd) which occurs 4 frames after the
initial strobe goes low and is held high for the
duration of 8 pcm bits.

SSI operation is separated into two categories based
upon the data rate of the available bit clock. If the bit
clock is 512 kHz or greater then it is used directly by
the internal MT9160B/61B functions allowing
synchronous operation. If the available bit clock is
128 kHz or 256 kHz, then a 4096 kHz master clock is
required to derive clocks for the internal MT9160B/
61B functions.

Applications where Bit Clock (BCL) is below 512 kHz
are designated as asynchronous. The MT9160B/61B
will re-align its internal clocks to allow operation
when the external master and bit clocks are
asynchronous. Control bits CSL2, CSL1 and CSL0 in
Control Register 2 (address 04h) are used to
program the bit rates.

frame delay through the FDI circuit for synchronous
operation.

For asynchronous operation Dout and Din are as
defined for synchronous operation except that the
allowed output jitter on Dout is larger. This is due to
the resynchronization circuitry activity and will not
affect operation since the bit cell period at 128 kb/s
and 256 kb/s is relatively large. There is a one frame
delay through the FDI circuit for asynchronous
operation. Refer to the specifications of Figures 13&
14 for both synchronous and asynchronous SSI
timing.

PWRST/Software Reset (Rst)

While the MT9160B/61B is held in PWRST no device
control or functionality is possible. While in software
reset (Rst=1, address 03h) only the microport is
functional. Software reset can only be removed by
writing the Rst bit low or by performing a hardware
PWRST. While the Rst bit is high, the other bits in
Control Register 1 are held low and cannot be
reprogrammed. Therefore to modify Control Register
1 the Rst bit must first be written low, followed by a
2nd write operation which writes the desired data.
This avoids a race condition between clearing the
reset bit and the writing of the other bits in Control
Register 1.

After a Power-up reset (PWRST) or software reset
(Rst) all control bits assume their "Power Reset
Value" default states; µ-Law coding, 0 dB Rx and
6dB Tx gains and the device powered up in SSI
mode 2048 kb/s operation with Dout tri-stated while
there is no strobe active on STB. If a valid strobe is
supplied to STB, then Dout will be active, during the
defined channel.

To attain complete power-down from a normal
operating condition, write PDFDI = 1 and PDDR = 1
(Control Register 1, address 03h) or set the PWRST
pin low.

For synchronous operation data is sampled, from
Din, on the falling edge of BCL during the time slot
defined by the STB input. Data is made available, on
Dout, on the rising edge of BCL during the time slot
defined by the STB input. Dout is tri-stated at all
times when STB is not true. If STB is valid and
PDDR is set, then quiet code will be transmitted on
Dout during the valid strobe period. There is no

88

MT9160B/61B Advance Information

Register Summary

Address Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Description

00 RxINC RxFG

RxFG

2

RxFG

1

TxINC TxFG

0

TxFG

2

TxFG

1

Gain Control

0

Register 1

01---- -STG2STG

STG

1

Gain Control

0

Register 2
02 - - - - - - - DrGain Path Control
03 PDFDI PDDR RST - TxMute RxMute TxBsel RxBsel Control

Register 1
04 CEN DEN D8 A/µ Smag/

ITU-T

05 C

7

C

6

C

5

C

4

C

3

CSL

C

CSL

2

CSL

1

0

Control

Register 2

2

C

1

C

0

C-Channel

Register

06 D

7

D

6

D

5

D

4

D

3

D

2

D

1

D

0

D-Channel

Register

07y----PCM/

loopen - - Loop Back

ANALOG

Table 2 - 5V Multi-featured Codec Register Map

Gain Control Register 1 ADDRESS = 00h WRITE/READ VERIFY

RxINC

RxFG2RxFG1RxFG

0

TxINC

TxFG2TxFG1TxFG

0

76543210

Receive Gain

Setting (dB)

(default) 0

-1

-2

-3

-4

-5

-6

-7

RxFGn = Receive Filter Gain bit n

RxINC: When high, the receive path nominal gain is set to 0 dB. When low, this gain is -6.0 dB.
TxINC: When high, the transmit nominal gain is set to 15.3 dB. When low, this gain is 6.0 dB.

RxFG

0
0
0
0
1
1
1
1

RxFG

2

0
0
1
1
0
0
1
1

RxFG

1

0

0
1
0
1
0
1
0
1

Transmit Gain

Setting (dB)

(default) 0

1
2
3
4
5
6
7

TxFGn = Transmit Filter Gain bit n

TxFG

0
0
0
0
1
1
1
1

Power Reset Value

TxFG

2

1000 0000

1

0
0
1
1
0
0
1
1

TxFG

0
1
0
1
0
1
0
1

0

Note: Bits marked "-" are reserved bits and should be written with logic "0"

89

Advance Information MT9160B/61B

Gain Control Register 2 ADDRESS = 01h WRITE/READ VERIFY

Power Reset Value

---- STG2STG1STG

-

0

76543210

XXXX X000

Side-tone Gain

Setting (dB)

(default) OFF

-9.96

-6.64

-3.32
0

3.32

6.64

9.96

STG

= Side-tone Gain bit n

n

STG

0
0
0
0
1
1
1
1

2

STG

0
0
1
1
0
0
1
1

STG

1

0

0
1
0
1
0
1
0
1

Path Control

ADDRESS = 02h WRITE/READ VERIFY

---

-

-

--

DrGain

76543210

DrGain When high, the receive path is summed with the side tone path and is attenuated by 6dB.

When low, the receive path contains no side tone (default).

Power Reset Value

XX00 0000

Note: Bits marked "-" are reserved bits and should be written with logic "0"

90

MT9160B/61B Advance Information

Control Register 1

PDFDI PDDR TxBsel RxBselRst

_

TxMute RxMute

ADDRESS = 03h WRITE/READ VERIFY

Power Reset Value

0000 0000

76543210

PDFDI When high, the FDI PLA and the Filter/Codec are powered down. When low, the FDI is active (default).
PDDR When high, the ear driver and Filter/Codec are powered down. In addition, in ST-BUS mode, the selected output

Rst When high, a software reset occurs performing the same function as the hardware reset (PWRST) except that the Rst

TxMute When high the transmit PCM stream is interrupted and replaced with quiet code; thus forcing the output code into a

RxMute When high the received PCM stream is interrupted and replaced with quiet code; thus forcing the receive path into a

TxBsel When high, the transmit B2 channel is functional in ST-BUS mode. When low, the transmit B1 channel is functional in

RxBsel When high, the receive B2 channel is functional in ST-BUS mode. When low, the receive B1 channel is functional in

channel is tri-stated. In SSI mode the PCM output code will be -zero code during the valid strobe period. The output will
be tri-stated outside of the valid strobe and for the whole frame if no strobe is supplied. When low, the driver and Filter/
Codec are active if PDFDI is low (default).

bit remains high and device remains powered up. A software reset can be removed only by writing this bit low or by
means of a hardware reset (PWRST). This bit is useful for quickly programming the Registers to the default Power
Reset Values. When this bit is low, the reset condition is removed allowing the registers to be modified.

mute state (only the output code is muted, the transmit microphone and transmit Filter/Codec are still functional). When
low the full transmit path functions normally (default).

mute state. When low the full receive path functions normally (default).

ST-BUS mode. Not used in SSI mode.

ST-BUS mode. Not used in SSI mode.

Control Register 2 ADDRESS = 04h WRITE/READ VERIFY

Power Reset Value

0000 0010

CEn DEn

D8

A/µ

Smag/
ITU-T

CSL

CSL1CSL

2

0

76543210

CEn When high, data written into the C-Channel register (address 05h) is transmitted during channel 1 on DSTo. When

DEn When high, data written into the D-Channel Register (address 06h) is transmitted (2 bits/frame) during channel 0

D8 When high, D-channel operates at 8kb/s. When low, D-channel operates at 16kb/s (default).
A/µ When high, A-Law encoding/decoding is selected for the MT9160B/61B. When low, µ-Law encoding/decoding is

Smag/ITU-T When high, sign-magnitude code assignment is selected for the Codec input/output. When low, ITU-T code

CSL

low, the channel 1 timeslot is tri-stated on DSTo. Channel 1 data received on DSTi is read via the C-Channel
register (address 05h) regardless of the state of CEn. This control bit has significance only for ST-BUS operation
and is ignored for SSI operation.

on DSTo. The remaining six bits of the D-Channel carry no information. When low, the channel 0 timeslot is
completely tri-stated on DSTo. Channel 0 data received on DSTi is read via the D-Channel register regardless of
the state of DEN. This control bit has significance only for ST-BUS mode and is ignored for SSI operation.

selected.
assignment is selected for the Codec input/output; true sign, inverted magnitude (µ-Law) or true sign, alternate

digit inversion (A-Law).

CSL

2

1 1 1 N/A 4096 ST-BUS
1 0 0 128 4096 SSI
1 0 1 256 4096 SSI
0 0 0 512 512 SSI
0 0 1 1536 1536 SSI
0 1 0 2048 2048 SSI (default)
0 1 1 4096 4096 SSI

CSL

1

Bit Clock rate (kHz) CLOCKin (kHz) Mode

0

Note: Bits marked "-" are reserved bits and should be written with logic "0"

91

Advance Information MT9160B/61B

C-Channel Register ADDRESS = 05h WRITE/READ

Power Reset Value

C7 C6 C5 C4 C2 C1 C0C3

76543210

Micro-port access to the ST-BUS C-Channel information read and write

1111 1111- write

XXXX XXXX - read

D-Channel Register

D7 D6 D5 D4 D2 D1 D0

D3

ADDRESS = 06h WRITE/READ

Power Reset Value

1111 1111- write

XXXX XXXX - read

76543210

D7-D0 Data written to this register will be transmitted every frame, in channel 0, if the DEn control bit is set (address 04h).

Loopback Register

Received D-Channel data is valid, regardless of the state of DEn. These bits are valid for ST-BUS mode only and are
accessible only when IRQ indicates valid access.

ADDRESS = 07h WRITE/READ VERIFY

--

--

-

PCM/

ANALOG

loopen

-

Power Reset Value

XXXX 0000

76543210

PCM/ANALOG This control bit functions only when loopen is set high. It is ignored when loopen is low.

For loopback operation when this bit is high, the device is configured for digital-to-digital loopback operation. Data on
Din is looped back to Dout without conversion to the analog domain. However, the receive D/A path (from Din to
HSPKR ±) still functions. When low, the device is configured for analog-to-analog operation. An analog input signal at
M± is looped back to the SPKR± outputs through the A/D and D/A circuits as well as through the normal transmit A/D
path (from M± to Dout).

loopen When high, loopback operation is enabled and the loopback type is governed by the state of the PCM/ANALOG bit.

When low, loopbacks are disabled, the device operates normally and the PCM/ANALOG bit is ignored.

Din

Dout

Dout

Analog Loopback

ANALOG = 0 loopen = 1

PCM/

HSPKR +/-

M +/-

Figure 8 - Loopback Signal Flows

Note: Bits marked "-" are reserved bits and should be written with logic "0"

Digital Loopback

PCM/

ANALOG = 1 loopen = 1

HSPKR +/-

92

MT9160B/61B Advance Information

Applications

Figure 9 shows an application in a digital phone set.

Various configurations of pair gain drops are
depicted in Figures 12a and 12b using the MT9125
and MT9126, respectively.

330Ω

10 µF

511Ω

+5V

0.1 µF

100K

+

+

­R

M+

10 µF

330Ω

+

+5V

1K

0.1 µF

VBias

T

+

-

R

M+

Electret
Microphone

INTEL

MCS-51

or

MOTOROLA

SPI

Micro-

Controller

+

+5V

511Ω

0.1 µF

0.1 µF

0.1 µF

100K

VBias

0.1 µF
100K

Differential Amplifier

VBias

1 µF

A/µ/IRQ

CS
SCLK
DATA1

DATA2
DATA2 Motorola

Mode only

Av = 1 + 2R

T

­+

+5V

+

Single-ended Amplifier

75Ω

75Ω

20
19
18
17
16
15
14
13
12
11

Electret

Microphone

T

R

M-

Typical External Gain

()

1
2

3
4

MT9160B

5
6

7
8
9

10

AV= 5-10

M+
M-

VBias

M-

150Ω

93

Twisted Pair

DC to DC
Converter

+5V

Lin

Z

Lout

T

MT8972

DNIC

10.24 MHz

Figure 9 - Digital Telephone Set

DSTi

DSTo

F0i

C4b

Advance Information MT9160B/61B

+5V

INTEL

MCS-51

or

MOTOROLA

SPI

Micro-

Controller

+5V

0.1 µF

0.1 µF

0.1 µF

100K

A/µ/IRQ

CS

SCLK
DATA1
DATA2
DATA2 Motorola

Mode only

From Digita

Phone

0.1 µF

0.1 µF

A/µ/IRQ

CS

SCLK
DATA1

DATA2
DATA2 Motorola

Mode only

l

Twisted Pair

1 µF

1 µF

VBias

VBias

Typical External Gain

()

1
2

3
4
5
6

7
8
9

10

11
12

DC to DC
Converter

1
2

3
4
5

6

7

8
9

10

11
12

AV= 5-10

MT9161B
1

MT9161B
2

24

23
22
21

20

19

18
17
16

15
14
13

+5V

Lin

Z

Lout

22
21

19

18
17

16
15
14
13

T

24
23

20

From Subscriber

Line Interface

+5V

DSTi

DSTo

MT8972

DNIC

From Subscriber

Line Interface

+5V

F0i

C4b

Output to Subscriber

Line Interface

F0od

Output to Subscriber

Line Interface

DC to DC

Converter

From Digital

Phone

Twisted Pair

C4 Clock Input

+5V

Lin

Z

Lout

DSTi

MT8972

T

DNIC

DSTo

F0i

C4b

Figure 10 - Delayed Frame Pulse of First MT9161B Signalling Second MT9161B

94

MT9160B/61B Advance Information

Absolute Maximum Ratings

†

Parameter Symbol Min Max Units

1 Supply Voltage VDD - V
2 Voltage on any I/O pin VI/V
3 Current on any I/O pin (transducers excluded) II/I
4 Storage Temperature T
5 Power Dissipation (package) P

†

Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.

Recommended Operating Conditions - Voltages are with respect to V

SS

O

O
S
D

unless otherwise stated

SS

- 0.3 7 V

VSS - 0.3 VDD + 0.3 V

- 65 + 150 °C

Characteristics Sym Min Typ Max Units Test Conditions

1 Supply Voltage V
2 CMOS Input Voltage (high) V
3 CMOS Input Voltage (low) V
4 Operating Temperature T

DD

IHC

ILC

4.75 5 5.25 V

4.5 V

V

SS

- 40 + 85 °C

A

DD

0.5 V

V

± 20 mA

750 mW

Power Characteristics

Characteristics Sym Min Typ Max Units Test Conditions

1 Static Supply Current (clock

disabled, all functions off, PDFDI/
PDDR=1, PWRST=0)

2 Dynamic Supply Current:

Total all functions enabled I

Note 1: Power delivered to the load is in addition to the bias current requirements.

I

DDC1

DDFT

420µA Outputs unloaded, Input

7.0 10 mA See Note 1.

signals static, not loaded

95

Advance Information MT9160B/61B

DC Electrical Characteristics

Characteristics Sym Min Typ

1 Input HIGH Voltage CMOS inputs V
2 Input LOW Voltage CMOS inputs V
3 VBias Voltage Output V
4V
5 Input Leakage Current I
6 Positive Going Threshold

Output Voltage V

Ref

†

- Voltages are with respect to ground (VSS) unless otherwise stated.
‡

Max Units Test Conditions

3.5 V

1.5 V

VDD/2 V Max. Load = 10kΩ

/2-1.9

V

DD

0.1 10 µAVIN=VDD to V

3.7

V No load

V

V

IHC
ILC

Bias

Ref

IZ
T+

Voltage (PWRST only)
Negative Going Threshold

V

T-

1.3

V

Voltage (PWRST only)

7 Output HIGH Current I

8 Output LOW Current I

9 Output Leakage Current I
10 Output Capacitance C
11 Input Capacitance C

† DC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.

* Note 1 - Magnitude measurement, ignore signs.

OH

OL

OZ

o

i

3 7 mA VOH = 0.9*V

510 mAV

0.01 10 µAV
15 pF
10 pF

See Note 1

= 0.1*V

OL

See Note 1

= VDD and V

OUT

SS

DD

DD

SS

Clockin Tolerance Characteristics (ST-BUS Mode)

Characteristics Min Typ

1 C4i Frequency 4095.6 4096 4096.4 kHz (i.e., 100 ppm)

† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.

‡

Max Units Test Conditions

96

MT9160B/61B Advance Information

AC Characteristics† for A/D (Transmit) Path - 0dBm0 = A

- 3.14dB =1.843V

1 Analog input equivalent to

overload decision

2 Absolute half-channel gain

M ± to Dout G

Tolerance at all other transmit
filter settings
(1 to 7dB)

3 Gain tracking vs. input level

ITU-T G.714 Method 2

4 Signal to total Distortion vs. input

level.
ITU-T G.714 Method 2

5 Transmit Idle Channel Noise N

6 Gain relative to gain at 1020Hz

<50Hz
60Hz
200Hz
300 - 3000 Hz
3000 - 3400 Hz
4000 Hz
>4600 Hz

for A-Law, at the Codec (V

rms

=0.6 volts and V

Ref

=2.5 volts.)

Bias

Characteristics Sym Min Typ

A

Li3.17

A

Li3.14

G

AX1
AX2

5.2

14.5

7.33

7.6

6.0

15.3

-0.2 ±0.1 +0.2 dB

G

TX

-0.3

-0.6

-1.6

D

QX

35
29
24

CX

N

PX

G

RX

8.5

-71

-45

-0.25

-0.9

-23

-40

‡

- 3.17dB = 1.773V

Lo3.17

for µ-Law and 0dBm0 = A

rms

Max Units Test Conditions

Vp-p
Vp-p

µ-Law
A-Law
Both at Codec

Transmit filter gain=0dB
setting.

6.8

16.1

dB
dB

TxINC = 0*
TxINC = 1*
@1020 Hz

0.3

0.6

1.6

12

-69

-25

-30

0.0

0.25

0.25

-12.5

-25

dB
dB
dB

dB
dB
dB

dBrnC0

dBm0p

dB
dB
dB
dB
dB
dB
dB

3 to -40 dBm0

-40 to -50 dBm0

-50 to -55 dBm0
0 to -30 dBm0

-40 dBm0

-45 dBm0
µ-Law

A-Law

Lo3.14

7 Absolute Delay D

AX

360 µs at frequency of minimum

delay

8 Group Delay relative to D

AX

9 Power Supply Rejection

f=1020 Hz
f=0.3 to 3 kHz
f=3 to 4 kHz
f=4 to 50 kHz

† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: TxINC, refer to Control Register 1, address 00h.

D

DX

PSSR
PSSR1
PSSR2
PSSR3

37

750
380
130
750

40
35
40

µs
µs
µs
µs

dB
dB
dB
dB

500-600 Hz
600 - 1000 Hz
1000 - 2600 Hz
2600 - 2800 Hz

±100mV peak signal on
V

DD

µ-law
PSSR1-3 not production
tested

97

Advance Information MT9160B/61B

AC Characteristics† for D/A (Receive) Path - 0dBm0 = A

3.14dB =1.843V

1 Analog output at the Codec full

scale

2 Absolute half-channel gain.

Din to HSPKR±

Tolerance at all other receive
filter settings (-1 to -7dB)
relative to output at 0dB setting

3 Gain tracking vs. input level

ITU-T G.714 Method 2

4 Signal to total distortion vs. input

level.
ITU-T G.714 Method 2

5 Receive Idle Channel Noise N

6 Gain relative to gain at 1020Hz

200Hz
300 - 3000 Hz
3000 - 3400 Hz
4000 Hz
>4600 Hz

for A-Law, at the Codec. (V

rms

=0.6 volts and V

Ref

=2.5 volts.)

Bias

Characteristics Sym Min Typ

A

Lo3.17

A

Lo3.14

G
G
G
G

AR1
AR2
AR3
AR4

-0.8

-6.8

-6.8

-12.8

7.225

7.481
0

-6

-6

-12

-0.2 ±0.1 +0.2 dB

G

TR

-0.3

-0.6

-1.6

G

QR

35
29
24

CR

N

PR

G

RR

7

-84

-0.25

-0.90

‡

- 3.17dB = 1.773V

Lo3.17

for µ-Law and 0dBm0 = A

rms

Max Units Test Conditions

0.8

-5.2

-5.2

-11.2

Vp-p
Vp-p

dB
dB
dB
dB

µ-Law
A-Law

DrGain=0, RxINC =1*
DrGain=0, RxINC =0*
DrGain=1, RxINC =1*
DrGain=1, RxINC =0*
@ 1020 Hz

0.3

0.6

1.6

10

-80

0.25

0.25

0.25

-12.5

-25

dB
dB
dB

dB
dB
dB

dBrnC0

dBm0p

dB
dB
dB
dB
dB

3 to -40 dBm0

-40 to -50 dBm0

-50 to -55 dBm0
0 to -30 dBm0

-40 dBm0

-45 dBm0
µ-Law

A-Law

Lo3.14

-

7 Absolute Delay D
8 Group Delay relative to D

AR

9 Crosstalk D/A to A/D

A/D to D/A

† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: RxINC, refer to Control Register 1, address 00h.

D

CT
CT

AR
DR

RT

TR

240 µs at frequency of min. delay
750

380
130
750

-74

-80

µs
µs
µs
µs

dB
dB

500-600 Hz
600 - 1000 Hz
1000 - 2600 Hz
2600 - 2800 Hz

G.714.16
ITU-T

98

MT9160B/61B Advance Information

AC Electrical Characteristics† for Side-tone Path

Characteristics Sym Min Typ‡Max Units Test Conditions

1 Absolute path gain

gain adjust = 0dB

G
G

AS1
AS2

-17.43

-11.43

-16.63

-10.63

-15.83

-9.83dBdB

RxINC = 0*
RxINC = 1*
M± inputs to HSPKR± outputs
1000 Hz at STG2=1

2 Tolerance of other side-tone

-0.5 +/-0.2 +0.5 dB
settings (-9.96 to 9.96 dB)
relative to output at 0dB setting

† AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: RxINC, refer to Control Register 1, address 00h.

Electrical Characteristics† for Analog Outputs

Characteristics Sym Min Typ‡Max Units Test Conditions

1 EarpIece load impedance E
2 Allowable earpiece capacitive

E

load

3 Earpiece harmonic distortion E

† Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: RxINC, refer to Control Register 1, address 00h.

260 300 ohms across HSPKR±

ZL

CL

D

300 pF each pin: HSPKR+,

0.5 % 300 ohms load across
HSPKR± (tol-15%),
VO≤693mV
Rx gain=0dB

HSPKR-

, RxINC=1*,

RMS

Electrical Characteristics† for Analog Inputs

2.90

1.03

‡

Max Units Test Conditions

Vp-p
Vp-p

TxINC = 0, A/µ = 0*
TxINC = 1, A/µ = 1*

Tx filter gain=0dB setting

Characteristics Sym Min Typ

1 Maximum input voltage without

overloading Codec
across M+/M- V

2 Input Impedance Z

† Electrical Characteristics are over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: TxINC, refer to Control Register 1, address 00h.

IOLH

I

50 kΩ M+/M- to V

SSA

99

Advance Information MT9160B/61B

AC Electrical Characteristics† - ST-BUS Timing (See figure 11)

Characteristics Sym Min Typ

‡

Max Units Test Conditions

1 C4i Clock Period t
2 C4i Clock High period t
3 C4i Clock Low period t
4 C4i Clock Transition Time t
5 F0i Frame Pulse Setup Time t
6 F0i Frame Pulse Hold Time t
7 Delayed Frame Pulse delay

t

F0odS

C4P
C4H

C4L

T

F0iS

F0iH

40 ns
40 ns

244 ns
122 ns
122 ns

20 ns

20 50 ns

after C4i rising

8 Delayed Frame Pulse hold

t

F0odH

20 50 ns

time from C4i rising

9 DSTo Delay t
10 DSTi Setup Time t
11 DSTi Hold Time t

† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing.
* Note: All conditions → data-data, data-HiZ, HiZ-data.

t

T

C4i

70%
30%

t

C4P

DSToD

DSTiS
DSTiH

1 bit cell

20 ns
50 ns

100 125 ns CL = 50pF, 1kΩ load.*

t

T

t

C4H

t

C4L

DSTo

DSTi

F0i

F0od

70%
30%

70%
30%

70%
30%

70%
30%

t

DSToD

t

DSTiS

t

F0iS

t

T

t

F0iH

t

T

64 Clock Periods

t

DSTiH

t

F0odS

NOTE: Levels refer to %V

t

F0odH

DD

Figure 11 - ST-BUS Timing Diagram

100

MT9160B/61B Advance Information

AC Electrical Characteristics† - SSI BUS Synchronous Timing (see figure 12)

Characteristics Sym Min Typ

‡

Max Units Test Conditions

1 BCL Clock Period t
2 BCL Pulse Width High t
3 BCL Pulse Width Low t

BCL
BCLH
BCLL

4 BCL Rise/Fall Time tR/t
5 Strobe Pulse Width t
6 Delayed Strobe Pulse Width t
7 Strobe setup time before BCL falling t
8 Strobe hold time after BCL falling t
9 Delayed Strobe Pulse delay after

ENW

ENWD

SSS

SSH

t

DSTBR

244 1953 ns BCL=4096 kHz to 512 kHz

122 ns BCL=4096 kHz
122 ns BCL=4096 kHz

F

70
80

20 ns Note 1

8 x t
8 x t

BCL
BCL

t

BCL-80

t

BCL-80

ns Note 1
ns Note 1
ns
ns

20 40 ns Note 1

BCL rising

10 Delayed Strobe Pulse hold time after

t

DSTBF

20 40 ns Note 1

BCL rising

11 Dout High Impedance to Active Low

t

DOZL

50 ns CL=150 pF, RL=1K

from Strobe rising

12 Dout High Impedance to Active High

t

DOZH

50 ns CL=150 pF, RL=1K

from Strobe rising

13 Dout Active Low to High Impedance

t

DOLZ

50 ns CL=150 pF, RL=1K

from Strobe falling

14 Dout Active High to High Impedance

t

DOHZ

50 ns CL=150 pF, RL=1K

from Strobe falling

15 Dout Delay (high and low) from BCL

t

DD

50 ns CL=150 pF, RL=1K

rising
16 Din Setup time before BCL falling t
17 Din Hold Time from BCL falling t

† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
NOTE 1: Not production tested, guaranteed by design.

DIS

DIH

20 ns
50 ns

101

Advance Information MT9160B/61B

t

BCL

t

F

t

BCLL

t

t

DIS

DIH

t

DD

t

t

SSS

t

ENW

NOTE: Levels refer to % VDD (CMOS I/O)

t

SSH

DOLZ

t

DOHZ

t

DSTBR

t

DSTBF

t

ENWD

CLOCKin

(BCL)

Din

Dout

STB

STBd

70%
30%

70%
30%

70%
30%

70%
30%

70%
30%

t

R

t

t

DOZL

DOZH

t

BCLH

Figure 12 - SSI Synchronous Timing Diagram

AC Electrical Characteristics† - SSI BUS Asynchronous Timing (note 1) (see figure 13)

Characteristics Sym Min Typ

1 Bit Cell Period T

2 Frame Jitter T
3 Bit 1 Dout Delay from STB

DATA

t

dda1

j

going high

4 Bit 2 Dout Delay from STB

going high

5 Bit n Dout Delay from STB

going high

6 Bit 1 Data Boundary T
7 Din Bit n Data Setup time from

STB rising

t

dda2

t

ddan

DATA1

t

SU

600+

T

DATA-Tj

600 +

(n-1) x

T

DATA-Tj

T

DATA-Tj

T

\2

DATA

+500ns-T

j

+(n-1) x

T

DATA

8 Din Data Hold time from STB

rising

t

ho

T

\2

DATA

+500ns+T

j

+(n-1) x

T

DATA

† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
NOTE 1: Not production tested, guaranteed by design.

‡

7812
3906

600+
T

DATA

600 +

(n-1) x

T

DATA

Max Units Test Conditions

nsnsBCL=128 kHz

BCL=256 kHz

600 ns

Tj+600 ns CL=150 pF, RL=1K

600 +

T

DATA+Tj

600 +

(n-1) x

T

DATA+Tj

T

DATA+Tj

ns CL=150 pF, RL=1K

ns CL=150 pF, RL=1K

n=3 to 8

ns
ns n=1-8

ns

102

MT9160B/61B Advance Information

T

j

STB

Dout

Din

70%
30%

70%
30%

70%
30%

t

dda1

t

dda2

t

dha1

Bit 1 Bit 2 Bit 3

T

DATA1

t

ho

t

su

D2

DAT A

T

DAT A

D1

/2

T

T

DATA

T

DAT A

D3

NOTE: Levels refer to % VDD (CMOS I/O)

Figure 13 - SSI Asynchronous Timing Diagram

AC Electrical Characteristics† - Microport Timing (see figure 14)

Characteristics Sym Min Typ

‡

Max Units Test Conditions

1 Input data setup t
2 Input data hold t
3 Output data delay t
4 Serial clock period t
5 SCLK pulse width high t
6 SCLK pulse width low t
7 CS setup-Intel t
8 CS setup-Motorola t
9 CS hold t

10 CS to output high impedance t

† Timing is over recommended temperature range & recommended power supply voltages.
‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing.
* Note: All conditions → data-data, data-HiZ, HiZ-data.

IDS

IDH

ODD

CYC

CH

CL

CSSI

CSSM

CSH

OHZ

100 ns

30 ns

100 ns CL = 150pF, RL = 1K *
500 1000 ns
250 500 ns
250 500 ns
200 ns
200 ns
100 ns

100 ns CL = 150pF, RL = 1K

103

Advance Information MT9160B/61B

SCLK

CS

SCLK

2.0V

0.8V

t

IDS

2.0V

0.8V

t

CSSI

t

CSSM

DATA INPUT

t

ODD

90%

10%

HiZ

Intel
Mode = 0

t

IDS

t

t

IDH

CH

DATA OUTPUT

t

CYC

2.0V

0.8V

2.0V

0.8V

t

t

CL

OHZ

2.0V

0.8V

t

t

ODD

2.0V

0.8V

CSH

2.0V

0.8V

90%

10%

Motorola
Mode = 00

HiZ

t

CH

t

t

CL

t

IDH

CYC

DATA OUTPUT

DATA INPUT

Figure 14 - Microport Timing

Intel® and MCS-51® are registered trademarks of Intel Corporation
Motorola® and SPI® are registered trademarks of Motorola Corporation
National® and Microwire® are trademarks of National Semiconductor Corporation

NOTE: % refers to % V

DD

104

Pin 1

Package Outlines

E

A

A

1

16-Pin 18-Pin 20-Pin 24-Pin 28-Pin

DIM

Min Max Min Max Min Max

A 0.093

A

1

B 0.013

C 0.009

D 0.398

E 0.291

e 0.050 BSC

H 0.394

L 0.016

(2.35)

0.004
(0.10)

(0.33)

(0.231)

(10.1)

(7.40)

(1.27 BSC)

(10.00)

(0.40)

0.104
(2.65)

0.012
(0.30)

0.020
(0.51)

0.013

(0.318)

0.413
(10.5)

0.299
(7.40)

0.419

(10.65)

0.050
(1.27)

D

0.093
(2.35)

0.004
(0.10)

0.013
(0.33)

0.009

(0.231)

0.447

(11.35)

0.291
(7.40)

0.050 BSC

(1.27 BSC)

0.394

(10.00)

0.016
(0.40)

L

e

4 mils (lead coplanarity)

Notes:

1) Not to scale

2) Dimensions in inches

3) (Dimensions in millimeters)

4) A & B Maximum dimensions include allowable mold flash

B

0.104
(2.65)

0.012
(0.30)

0.030
(0.51)

0.013

(0.318)

0.4625
(11.75)

0.299
(7.40)

0.419

(10.65)

0.050
(1.27)

0.093
(2.35)

0.004
(0.10)

0.013
(0.33)

0.009

(0.231)

0.496

(12.60)

0.291
(7.40)

0.050 BSC
(1.27 BSC)

0.394

(10.00)

0.016
(0.40)

0.104
(2.65)

0.012
(0.30)

0.020
(0.51)

0.013

(0.318)

0.512

(13.00)

0.299
(7.40)

0.419

(10.65)

0.050
(1.27)

Lead SOIC Package - S Suffix

C

H

L

Min Max Min Max

0.093

(2.35)

0.004

(0.10)

0.013

(0.33)

0.009

(0.231)

0.5985
(15.2)

0.291

(7.40)

0.050 BSC

(1.27 BSC)

0.394

(10.00)

0.016

(0.40)

0.104

(2.65)

0.012

(0.30)

0.020

(0.51)

0.013

(0.318)

0.614

(15.6)

0.299

(7.40)

0.419

(10.65)

0.050

(1.27)

0.093
(2.35)

0.004
(0.10)

0.013
(0.33)

0.009

(0.231)

0.697
(17.7)

0.291
(7.40)

0.050 BSC

(1.27 BSC)

0.394

(10.00)

0.016
(0.40)

(0.318)

0.7125

(10.65)

0.104
(2.65)

0.012
(0.30)

0.020
(0.51)

0.013

(18.1)

0.299
(7.40)

0.419

0.050
(1.27)

NOTES: 1. Controlling dimensions in parenthesis ( ) are in millimeters.

2. Converted inch dimensions are not necessarily exact.

General-7

Package Outlines

E

1

D

32

n-2 n-1 n

1

E

L

Notes:

1) Not to scale

2) Dimensions in inches

3) (Dimensions in millimeters)

A

b

D

1

e

2

b

A

2

Plastic Dual-In-Line Packages (PDIP) - E Suffix

8-Pin 16-Pin 18-Pin 20-Pin

DIM

Plastic Plastic Plastic Plastic

Min Max Min Max Min Max Min Max

A

A

2

b

b

2

C
D

D

1

E

E

1

e

e

A

L

e

B

e

C

NOTE: Controlling dimensions in parenthesis ( ) are in millimeters.

0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95)

0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558)

0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77)

0.008

(0.203)

0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9)

0.005 (0.13) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13)

0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26)

0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11)

0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54)

0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62)

0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81)

0 0.060 (1.52) 0 0.060 (1.52) 0 0.060 (1.52) 0 0.060 (1.52)

0.210 (5.33) 0.210 (5.33) 0.210 (5.33) 0.210 (5.33)

0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356)

0.430 (10.92) 0.430 (10.92) 0.430 (10.92) 0.430 (10.92)

C

e

A

e

B

e

C

General-8

E

1

L

Notes:

1) Not to scale

2) Dimensions in inches

3) (Dimensions in millimeters)

Package Outlines

32

1

E

n-2 n-1 n

D

A

b

D

1

e

2

b

A

2

C

e

A

e

B

Plastic Dual-In-Line Packages (PDIP) - E Suffix

α

DIM

A

A

2

b

b

2

C
D

D

1

E
E

E

1

E

1

e

e

A

e

A

e

B

L

α

22-Pin 24-Pin 28-Pin 40-Pin

Plastic Plastic Plastic Plastic

Min Max Min Max Min Max Min Max

0.210 (5.33) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35)

0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95)

0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558)

0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77)

0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381)

1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2)

0.005 (0.13) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13)

0.390 (9.91) 0.430 (10.92) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02)

0.290 (7.37) .330 (8.38)

0.330 (8.39) 0.380 (9.65) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73)

0.246 (6.25) 0.254 (6.45)

0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54)

0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24)

0.300 BSC (7.62)

0.430 (10.92)

0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08)
15° 15° 15° 15°

Shaded areas for 300 Mil Body Width 24 PDIP only

http://www.mitelsemi.com

World Headquarters - Canada

Tel: [phone]

Fax: [phone]

North America Asia/Pacific Europe, Middle East,

Tel: [phone] Tel: [phone] and Africa (EMEA)

Fax: [phone] Fax: [phone] Tel: [phone]

Fax: [phone]

Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.

This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s
conditions of sale which are available on request.

M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation
Mitel Semiconductor is an ISO 9001 Registered Company
Copyright 1999 MITEL Corporation
All Rights Reserved
Printed in CANADA

TECHNICAL DOCUMENTATION - NOT FOR RESALE