Datasheet MPIC2111P, MPIC2111D Datasheet (Motorola)

1

Motorola Power Products Division Advanced Data

Power Products Division

 

 

The MPIC2111 is a high voltage, high speed, power MOSFET and IGBT driver
with dependent high and low side referenced output channels designed for half–
bridge applications. Proprietary HVIC and latch immune CMOS technologies en­able ruggedized monolithic construction. Logic input is compatible with standard
CMOS outputs. The output drivers feature a high pulse current buffer stage de­signed for minimum driver cross–conduction. Internal deadtime is provided to
avoid shoot–through in the output half–bridge. The floating channel can be used to
drive an N–channel power MOSFET or IGBT in the high side configuration which
operates from 10 to 600 volts.

• Floating Channel Designed for Bootstrap Operation

• Fully Operational to +600 V

• Tolerant to Negative Transient Voltage

• dV/dt Immune

• Gate Drive Supply Range from 10 to 20 V

• Undervoltage Lockout for Both Channels

• CMOS Schmitt–triggered Inputs with Pull–down

• Matched Propagation Delay for Both Channels

• Internally Set Deadtime

• High Side Output in Phase with Input

PRODUCT SUMMARY

V

OFFSET 600 V MAX

I

O+/– 200 mA/420 mA

V

OUT 10 – 20 V

t

on/off

(typical)

130 & 90 ns

Deadtime (typical)

700 ns

V

B

8V

CC

IN

COM

HO
V

S

7
6
5

1
2
3
4

V

B

8V

CC

IN

COM

HO
V

S

7
6
5

1
2
3
4

LO LO

PIN CONNECTIONS

8 LEADS DIP

MPIC2111P

8 LEAD SOIC

MPIC2111D

(TOP VIEW)

This document contains information on a new product. Specifications and information herein are subject
to change without notice.

REV 1

Order this document

by MPIC2111/D



SEMICONDUCTOR TECHNICAL DATA



Device

Package

HALF–BRIDGE DRIVER

ORDERING INFORMATION

MPIC2111P PDIP

D SUFFIX

PLASTIC PACKAGE

CASE 751–05

(SO–8)

8

1

P SUFFIX

PLASTIC PACKAGE

CASE 626–05

8

1

MPIC2111D SOIC

 Motorola, Inc. 1996

MPIC2111

2

Motorola Power Products Division Advanced Data

SIMPLIFIED BLOCK DIAGRAM

PULSE

GEN

UV

DETECT

PULSE
FILTER

HV

LEVEL

SHIFT

COM

LO

V

CC

V

S

V

B

HO

R
R

S

Q

IN

UV

DETECT

DEAD

TIME

DEAD

TIME

ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute
voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air
conditions.

Rating

Symbol Min Max Unit

B

V

S

DC

High Side Floating Output Voltage
Low Side Fixed Supply Voltage

V

HO

V

VS–0.3

–0.3

VB+0.3

25

Low Side Fixed Supply Voltage
Low Side Output Voltage

V

CC

V

LO

–0.3
–0.3

25

VCC+0.3

LO

V

IN

CC

+0.3

VCC+0.3

Allowable Offset Supply Voltage Transient dVS/dt – 50 V/ns
*Package Power Dissipation @ TC ≤ +25°C (8 Lead DIP)

(8 Lead SOIC)

P

D

–

–
–

1.0

0.625

Watt

Thermal Resistance, Junction to Ambient (8 Lead DIP)

(8 Lead SOIC)

R

θJA

–
–

125
200

°C/W

Operating and Storage Temperature Tj, T

stg

–55 150 °C

Lead Temperature for Soldering Purposes, 10 seconds T

L

– 260 °C

RECOMMENDED OPERATING CONDITIONS

The Input/Output logic timing Diagram is shown in Figure 1. For proper operation the device should be used within the recommended condi­tions. The VS offset rating is tested with all supplies biased at 15 V differential.

High Side Floating Supply Absolute Voltage

V

B

VS+10 VS+20

High Side Floating Supply Offset Voltage V

S

Note 1 600

High Side Floating Output Voltage V

HO

V

S

V

B

Low Side Fixed Supply Voltage V

CC

10 20

Low Side Output Voltage V

LO

0 V

CC

Logic Input Voltage V

IN

0 V

CC

Ambient Temperature T

A

–40 125 °C

Note 1: Logic operational for VS of –5 to +600 V. Logic state held for VS of –5 V to –VBS.

High Side Floating Supply Absolute Voltage
High Side Floating Supply Offset Voltage

Logic Input Voltage

V

B

–0.3

VB–25

–0.3

625

VB+0.3

V

DC

V

mA

MPIC2111

3

Motorola Power Products Division Advanced Data

ELECTRICAL CHARACTERISTICS (T

A

= 25°C unless otherwise specified)

Characteristic

Symbol Min Typ Max Unit

STATIC ELECTRICAL CHARACTERISTICS

V

BIAS

(VCC, VBS) = 15 V unless otherwise specified. The VIN, VTH and IIN parameters are referenced to COM. The VO and IO parameters

are referenced to COM and are applicable to the respective output leads: HO or LO.

Logic “1” Input Voltage for HO & Logic “0” Input Voltage for LO @ VCC = 10 V V

IH

6.4 – –

Logic “1” Input Voltage for HO & Logic “0” Input Voltage for LO @ VCC = 15 V V

IH

9.5 – –

DC

Logic “1” Input Voltage for HO & Logic “0” Input Voltage for LO @ VCC = 20 V V

IH

12.6 – –

Logic “0” Input Voltage for HO & Logic “1” Input Voltage for LO @ VCC = 10 V V

IL

– – 3.8

Logic “0” Input Voltage for HO & Logic “1” Input Voltage for LO @ VCC = 15 V V

IL

– – 6.0

Logic “0” Input Voltage for HO & Logic “1” Input Voltage for LO @ VCC = 20 V V

IL

– – 8.3

High Level Output Voltage, V

BIAS–VO

@ IO = 0 A V

OH

– – 100

Low Level Output Voltage, VO @ IO = 0 A V

OL

– – 100

Offset Supply Leakage Current @ VB = VS = 600 V I

LK

– – 50

µA

Quiescent VBS Supply Current @ VIN = 0 V or V

CC

I

QBS

– 50 –

Quiescent VCC Supply Current @ VIN = 0 V or V

CC

I

QCC

– 70 –

Logic “1” Input Bias Current @ VIN = 15 V I

IN+

– 20 40

Logic “0” Input Bias Current @ VIN = 0 V I

IN–

– – 1.0

VBS Supply Undervoltage Positive Going Threshold V

BSUV+

– 8.5 –

VBS Supply Undervoltage Negative Going Threshold V

BSUV–

– 8.2 –

VCC Supply Undervoltage Positive Going Threshold V

CCUV+

– 8.6 –

VCC Supply Undervoltage Negative Going Threshold V

CCUV–

– 8.2 –

Output High Short Circuit Pulsed Current @ V

OUT

= 0 V, PW ≤ 10 µs I

O+

200 250 –

Output Low Short Circuit Pulsed Current @ V

OUT

= 15 V, PW ≤ 10 µs I

O–

420 500 –

DYNAMIC ELECTRICAL CHARACTERISTICS

V

BIAS

(VCC, VBS) = 15 V unless otherwise specified

Turn–On Propagation Delay @ VS = 0 V t

on

– 850 –

Turn–Off Propagation Delay @ VS = 600 V t

off

– 150 –

Turn–On Rise Time @ CL = 1000 pF t

r

– 80 –

Turn–Off Fall Time @ CL = 1000 pF t

f

– 40 –
Deadtime, LS Turn–Off to HS Turn–On & HS Turn–Off to LS Turn–On DT – 700 –
Delay Matching, HS & LS Turn–On/Off MT – 30 –

TYPICAL CONNECTION

IN

V

CC

V

CC

IN

COM

V

S

HO

V

B

LO

TO

LOAD

10 TO 600 V

V

DC

mV

V

mA

ns

MPIC2111

4

Motorola Power Products Division Advanced Data

LEAD DEFINITIONS

Symbol Lead Description

IN Logic Input for High Side and Low Side Gate Driver Outputs (HO & LO), In Phase with HO

V

B

High Side Floating Supply

HO High Side Gate Drive Output

V

S

High Side Floating Supply Return

V

CC

Low Side Supply

L

O

Low Side Gate Drive Output

COM Logic and Low Side Return

Figure 1. Input / Output Timing Diagram

Figure 2. Switching Time Waveform

Definitions

HO

IN

Figure 3. Deadtime Waveform Definitions

IN

50% 50%

IN (LO)

IN (HO)

LO
HO

50% 50%

10% 10%

90% 90%

t

r

LO

t

on

t

f

t

off

HO

LO

90%

90%

10%

10%

DT

MPIC2111

5

Motorola Power Products Division Advanced Data

PACKAGE DIMENSIONS

CASE 626–05

ISSUE K

NOTES:

1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.

2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).

3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

STYLE 1:

PIN 1. AC IN

2. DC + IN

3. DC – IN

4. AC IN

5. GROUND

6. OUTPUT

7. AUXILIARY

8. V

CC

1 4

58

F

NOTE 2

–A–

–B–

–T–

SEATING
PLANE

H

J

G

D

K

N

C

L

M

M

A

M

0.13 (0.005) B

M

T

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A 9.40 10.16 0.370 0.400
B 6.10 6.60 0.240 0.260
C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020
F 1.02 1.78 0.040 0.070

G 2.54 BSC 0.100 BSC

H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
K 2.92 3.43 0.115 0.135
L 7.62 BSC 0.300 BSC

M ––– 10 ––– 10

N 0.76 1.01 0.030 0.040

_ _

CASE 751–05

ISSUE P

SEATING
PLANE

1

4

58

C

K

4X P

A0.25 (0.010)MT B

S S

0.25 (0.010)

M

B

M

8X D

R

M

J

X 45

_

_

F

–A–

–B–

–T–

DIM MIN MAX

MILLIMETERS

A 4.80 5.00
B 3.80 4.00
C 1.35 1.75
D 0.35 0.49
F 0.40 1.25
G 1.27 BSC
J 0.18 0.25
K 0.10 0.25
M 0 7
P 5.80 6.20
R 0.25 0.50

__

G

NOTES:

1. DIMENSIONS A AND B ARE DATUMS AND T IS A
DATUM SURFACE.

2. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

3. DIMENSIONS ARE IN MILLIMETER.

4. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.

5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

6. DIMENSION D DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE D DIMENSION AT MAXIMUM MATERIAL
CONDITION.

MPIC2111

6

Motorola Power Products Division Advanced Data

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: [e-mail] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MPIC2111/D

*MPIC2111/D*

◊