Datasheet MM74HC132SJX, MM74HC132N, MM74HC132MTCX, MM74HC132M, MM74HC132SJ Datasheet (Fairchild Semiconductor)
...Page 1
September 1983
Revised February 1999
MM74HC132 Quad 2-Input NAND Schmitt Trigger
© 1999 Fairchild Semiconductor Corporation DS005309.prf www.fairchildsemi.com
MM74HC132
Quad 2-Input NAND Schmitt Trigger
General Description
The MM74HC132 utilizes advanced silicon-gate CMOS
technology to achieve the low power dissipation and high
noise immunity of standard CMOS, as well as the capability
to drive 10 L S-TTL loads.
The 74HC logic family is functionally and pinout compatible
with the standard 74LS logic family. All inputs are protected
from damage due to static discharge by internal diode
clamps to V
CC
and ground.
Features
■ Typical propagation delay: 12 ns
■ Wide power supply range: 2V–6V
■ Low quiescent current: 20 µA maxi mum (74HC Series)
■ Low input current: 1 µA maximum
■ Fanout of 10 LS-TTL loads
■ Typical hysteresis voltage: 0.9V at V
CC
=4.5V
Ordering Code:
Devices also availab le in Tape and Reel. Specify by appending th e s uffix let t er “X” to the ordering cod e. (Tape and Reel not available in N14A.)
Connection Diagram
Pin Assignment for DIP, SOIC, SOP, and TSSOP
Top View
Logic Diagram
Order Number Package Number Package Description
MM74HC132M M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
MM74HC132SJ M14D 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
MM74HC132MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
MM74HC132N N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Page 2
www.fairchildsemi.com 2
MM74HC132
Absolute Maximum Ratings(Note 1)
(Note 2)
Recommended Operating
Conditions
Note 1: Absolute Maximum Ratings are those values beyond which dam-
age to the device may occur.
Note 2: Unless otherwise specified all voltages are referenced to ground.
Note 3: Power Dissipation temper ature dera ting — plas tic “N” packa ge: −
DC Electrical Characteristics (Note 4)
Note 4: For a power supply of 5V ±1 0% the worst c ase ou tput volta ges (VOH, and VOL) occur for HC at 4.5V. Thus the 4. 5V valu es shoul d be use d when
designing with this supply. Worst case V
IH
and VIL occur at V
CC
= 5.5V and 4.5V res pectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage c ur-
rent (I
IN
, ICC, and IOZ) occur for CMOS at the higher voltage and so th e 6. 0V values should be used.
Supply Voltage (VCC) −0.5 to +7.0V
DC Input Voltage (V
IN
) −1.5 to V
CC
+1.5V
DC Output Voltage (V
OUT
) −0.5 to V
CC
+0.5V
Clamp Diode Current (I
IK
, IOK) ±20 mA
DC Output Current, per pin (I
OUT
) ±25 mA
DC V
CC
or GND Current, per pin (ICC) ±50 mA
Storage Temperature Range (T
STG
) −65°C to +150°C
Power Dissipation (P
D
)
(Note 3) 600 mW
S.O. Package only 500 mW
Lead Temperature (T
L
)
(Soldering 10 seconds) 260°C
Min Max Units
Supply Voltage (V
CC
)26V
DC Input or Output Voltage 0 V
CC
V
(V
IN
, V
OUT
)
Operating Temperature Range (T
A
) −40 +125 °C
Symbol Parameter Conditions
V
CC
TA = 25°C
TA = -40 to 85°CTA = -40 to 125°C
Units
Typ Guaranteed Limits
V
T+
Positive Going Min 2.0V 1.0 1.0 1.0 V
Threshold Voltage 4.5V 2.0 2.0 2.0 V
6.0V 3.0 3.0 3.0 V
Max 2.0V 1.5 1.5 1.5 V
4.5V 3.15 3.15 3.15 V
6.0V 4.2 4.2 4.2 V
V
T−
Negative Going Min 2.0V 0.3 0.3 0.3 V
Threshold Voltage 4.5V 0.9 0.9 0.9 V
6.0V 1.2 1.2 1.2 V
Max 2.0V 1.0 1.0 1.0 V
4.5V 2.2 2.2 2.2 V
6.0V 3.0 3.0 3.0 V
V
H
Hysteresis Voltage Min 2.0V 0.2 0.2 0.2 V
4.5V 0.4 0.4 0.4 V
6.0V 0.5 0.5 0.5 V
Max 2.0V 1.0 1.0 1.0 V
4.5V 1.4 1.4 1.4 V
6.0V 1.5 1.5 1.5 V
V
OH
Minimum HIGH Level V
IN
= VIH or V
IL
2.0V 2.0 1.9 1.9 1.9 V
Output Voltage |I
OUT
| ≤ 20 µA 4.5V 4.5 4.4 4.4 4.4 V
V
IN
= VIH or V
IL
6.0V 6.0 5.9 5.9 5.9 V
|I
OUT
| ≤ 4.0 mA 4.5V 4.2 3.98 3.84 3.7 V
|I
OUT
| ≤ 5.2 mA 6.0V 5.7 5.48 5.34 5.2 V
V
OL
Maximum LOW Level V
IN
= VIH or V
IL
2.0V 0 0.1 0.1 0.1 V
Output Voltage |I
OUT
| ≤ 20 µA 4.5V 0 0.1 0.1 0.1 V
V
IN
= VIH or V
IL
6.0V 0 0.1 0.1 0.1 V
|I
OUT
| ≤ 4.0 mA 4.5V 0.2 0.26 0.33 0.4 V
|I
OUT
| ≤ 5.2 mA 6.0V 0.2 0.26 0.33 0.4 V
I
IN
Maximum Input Current V
IN
= VCC or GND 6.0V ±0.1 ±1.0 ±1.0 µA
I
CC
Maximum Quiescent V
IN
= VCC or GND 6.0V 2.0 20 40 µA
Supply Current I
OUT
= 0 µA
Page 3
3 www.fairchildsemi.com
MM74HC132
AC Electrical Characteristics
V
CC
= 5V, T
A
= 25°C, C
L
= 15 pF, tr = t
f
= 6 ns
AC Electrical Characteristics
V
CC
= 2.0V to 6.0V, CL = 50 pF, tr = t
f
= 6 ns (unless otherwise specified)
Note 5: CPD determines the no load dynamic power con s um ption, PD = CPD V
CC
2
f + ICC VCC, and the no load dynam ic cu rrent consumption,
I
S
= CPDVCCf + ICC.
Symbol Parameter Conditions Typ
Guaranteed
Limit
Units
t
PHL
, t
PLH
Maximum Propagation Delay 12 20 ns
Symbol Parameter Conditions
V
CC
TA = 25°C
TA= −40 to 85°CTA= −55 to 125°C
Units
Typ Guaranteed Limits
t
PHL
, t
PLH
Maximum 2.0V 63 125 158 186 ns
Propagation Delay 4.5V 13 25 32 37 ns
6.0V 11 21 27 32 ns
t
TLH
, t
THL
Maximum Output 2.0V 30 75 95 110 ns
Rise and Fall Time 4.5V 8 15 19 22 ns
6.0V 7 13 16 19 ns
C
PD
Power Dissipation (per gate) 130 pF
Capacitance (Note 5)
C
IN
Maximum Input Capacitance 5 10 10 pF
Page 4
www.fairchildsemi.com 4
MM74HC132
Physical Dimensions inches (millimeters) unless otherwise noted
14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150” Narrow Body
Package Number M14A
14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide
Package Number M14D
Page 5
5 www.fairchildsemi.com
MM74HC132
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC14
Page 6
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
MM74HC132 Quad 2-Input NAND Schmitt Trigger
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or syste ms
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant inju ry to the
user.
2. A critical component i n any compon ent of a lif e support
device or system whose failu re to perform can be reasonably expected to ca use the fa i lure of the life su pp ort
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300” Wide
Package Number N14A
Loading...