Page 1
5-1
FACT DATA
The MC74AC4040 consists of 12 master-slave flip-flops. The output of each
flip-flop feeds the next and the frequency at each output is half that of the preceding
one. The state of the counter advances on the negative-going edge of the Clock
input. Reset is asynchronous and active-high.
State changes of the Q outputs do not occur simultaneously because of internal
ripple delays. Therefore, decoded output signals are subject to decoding spikes
and may have to be gated with the Clock of the MC74AC4040 for some designs.
• 140 MHz Typ. Clock
• Outputs Source/Sink 24 mA
• Operating Voltage Range: 2.0 to 6.0 V
• High Noise Immunity
1516 14 13 12 11 10
21 3 4 5 6 7
V
CC
9
8
Q11 Q10 Q8 Q9 RESET CLK Q1
Q12 Q6 Q5 Q7 Q4 Q3 Q2 GND
FUNCTION TABLE
Clock Reset Output State
L No Change
L Advance to next state
X H All Outputs are low
12-STAGE
BINARY RIPPLE
COUNTER
N SUFFIX
CASE 648-08
PLASTIC
D SUFFIX
CASE 751B-05
PLASTIC
LOGIC DIAGRAM
CLOCK
10
11
RESET
PIN 16 = V
CC
PIN 8 = GND
9
7
6
5
3
2
4
13
12
14
15
1
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
Page 2
MC74AC4040
5-2
FACT DATA
MAXIMUM RATINGS*
Symbol Parameter Value Unit
V
CC
DC Supply Voltage (Referenced to GND) –0.5 to +7.0 V
V
in
DC Input Voltage (Referenced to GND) –0.5 to VCC +0.5 V
V
out
DC Output Voltage (Referenced to GND) –0.5 to VCC +0.5 V
I
in
DC Input Current, per Pin ±20 mA
I
out
DC Output Current, per Pin ±50 mA
I
CC
DC VCC or GND Current per Output Pin ±50 mA
P
D
Power Dissipation in Still Air
Plastic**
SOIC Package**
750
500
mW
T
stg
Storage Temperature –65 to +150 °C
T
L
Lead Temperature, 1 mm from Case for 10 seconds
(Plastic DIP or SOIC Package)
260 °C
* Maximum Ratings are those values beyond which damage to the device may occur.
** Derating: Plastic DIP: – 10mW/°C from 65°C to 125°C
SOIC Package: –7.0 mW/°C from 65°C to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
VCC DC Supply Voltage (Referenced to GND) 2.0 6.0 V
Vin/V
out
Input Voltage, Output Voltage (Ref. to GND) 0 V
CC
T
A
Operating Temperature, All Package Types –40 +85 °C
/t
= 3.0 V
tr/tfInput Rise/Fall Time
(Figure 1)
VCC = 3.0 V
VCC = 4.5 V
0015040ns/V
VCC = 5.5 V
t
Input Rise/Fall Time V
0 150 ns/V
0 25
Page 3
MC74AC4040
5-3
FACT DATA
DC CHARACTERISTICS (unless otherwise specified)
Symbol Parameter Value Unit
Vin = VCC or GND
µA
VCC = 5.5 V,
CC
TA = Worst Case
Vin = VCC or GND
µA
VCC = 5.5 V,
CC
TA = 25°C
DC CHARACTERISTICS
74AC 74AC
Symbol
Parameter
V
CC
(V)
TA = +25°C
TA =
–40°C to +85°C
Unit
Conditions
Typ Guaranteed Limits
V
IH
3.0 2.1 2.1 V
OUT
= 0.1 V
4.5 3.15 3.15 V or VCC – 0.1 V
5.5 3.85 3.85
V
IL
3.0 0.9 0.9 V
OUT
= 0.1 V
4.5 1.35 1.35 V or VCC – 0.1 V
5.5 1.65 1.65
V
OH
3.0 2.99 2.9 2.9 I
OUT
= –50 µA
4.5 4.49 4.4 4.4 V
5.5 5.49 5.4 5.4
*VIN = VIL or V
IH
3.0 2.56 2.46
–12 mA
4.5 3.86 3.76
V
I
OH
–24 mA
5.5 4.86 4.76 –24 mA
V
OL
3.0 0.002 0.1 0.1 I
OUT
= 50 µA
4.5 0.001 0.1 0.1 V
5.5 0.001 0.1 0.1
*VIN = VIL or V
IH
3.0 0.36 0.44
12 mA
4.5 0.36 0.44
V
I
OL
24 mA
5.5 0.36 0.44 24 mA
I
IN
5.5
±0.1
±1.0
µA
VI = VCC, GND
I
OLD
5.5 75 mA V
OLD
= 1.65 V Max
I
OHD
Output Current**
5.5 –75 mA V
OHD
= 3.85 V Min
* All outputs loaded; thresholds on input associated with output under test.
** Maximum test duration 2.0 ms, one output loaded at a time.
I
CC
I
CC
Maximum Quiescent Supply Voltage 80
Maximum Quiescent Supply Current 8.0
Minimum High Level
Input Voltage
Maximum Low Level
Input Voltage
Minimum High Level
Output Voltage
Maximum Low Level
Output Voltage
Maximum Input
Leakage Current
Minimum Dynamic
Page 4
MC74AC4040
5-4
FACT DATA
AC CHARACTERISTICS (For Figures and Waveforms — See Section 3)
74AC 74AC
Symbol
Parameter
VCC*
(V)
TA = +25°C
CL = 50 pF
TA = –40°C
to +85°C
CL = 50 pF
Unit
Fig.
No.
Min Typ Max Min Max
Maximum Clock
3.3 110 120 100
f
max
Frequency 5.0 130 140 120
MHz
Propagation Delay
3.3 2.0 11 2.0 14
nCP to Q1
nCP to Q1 5.0 2.0 8.0 2.0 10
ns
Propagation Delay
3.3 0 5.5 0 6.5
Qn to Qn +1
Qn to Qn +1 5.0 0 3.5 0 4.5
ns
Propagation Delay
3.3 3.0 12 3.0 15
MR to Q
5.0 3.0 10 3.0 12
ns
3.3 0 –2.5 0
rec
nCP to MR
Recovery Time
5.0 0 –1.5 0
ns
3.3 4.0 3.5 4.5
tw n
CP
5.0 3.0 2.5 3.5
ns
3.3 4.0 3.5 4.5
tw MR
3.0 3.0 2.5 3.5
ns
* Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol Parameter
Value
Typ
Unit Test Conditions
C
IN
Input Capacitance 4.5 pF VCC = 5.0 V
C
PD
Power Dissipation Capacitance 50 pF VCC = 5.0 V
MR to Q
t
HL
t
rec
Minimum Pulse Width
Clock Pin
Minimum Pulse Width
Master Reset
Page 5
MC74AC4040
5-5
FACT DATA
OUTLINE DIMENSIONS
N SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
1 8
16 9
SEATING
PLANE
F
J
M
R
X 45
_
G
8 PLP
–B–
–A–
M
0.25 (0.010) B
S
–T–
D
K
C
16 PL
S
B
M
0.25 (0.010) A
S
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
_ _ _ _
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A–
B
F
C
S
H
G
D
J
L
M
16 PL
SEATING
1 8
916
K
PLANE
–T–
M
A
M
0.25 (0.010) T
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0 10 0 10
S 0.020 0.040 0.51 1.01
____
How to reach us:
USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com –TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters can and do vary in different
applications. All operating parameters, including “T ypicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
MC74AC4040/D
*MC74AC4040/D*
◊
Loading...