Page 1
5-1
FACT DATA
The MC74AC352/74ACT352 is a very high-speed dual 4-input multiplexer with
common Select inputs and individual Enable inputs for each section. It can select
two bits of data from four sources. The two buffered outputs present data in the
inverted (complementary) form. The MC74AC352/74ACT352 is the functional
equivalent of the MC74AC153/74ACT153 except with inverted outputs.
• Inverted Version of the MC74AC153/74ACT153
• Separate Enables for Each Multiplexer
• Outputs Source/Sink 24 mA
• ′ACT352 Has TTL Compatible Inputs
1516 14 13 12 11 10
21 3 4 5 6 7
V
CC
9
8
E
bS0I3bI2bI1bI0bZb
E
aS1I3aI2aI1aI0aZa
GND
PIN NAMES
I0a–I
3a
Side A Data Inputs
I0b–I
3b
Side B Data Inputs
S0, S1Common Select Inputs
E
a
Side A Enable Input
E
b
Side B Enable Input
Z
a, Zb
Multiplexer Outputs
TRUTH TABLE
Select Inputs Inputs (a or b) Output
S
0
S
1
E I0 I1I2I
3
Z
X X H X X X X H
L L L L X X X H
L L L H X X X L
H L L X L X X H
H L L X H X X L
L H L X X L X H
L H L X X H X L
H H L X X X L H
H H L X X X H L
H = HIGH Voltage Level
L = LOW Voltage Level
X = Immaterial
DUAL 4-INPUT
MULTIPLEXER
N SUFFIX
CASE 648-08
PLASTIC
D SUFFIX
CASE 751B-05
PLASTIC
LOGIC SYMBOL
S
0
S
1
EaI0aI1aI2aI
3a
Z
a
Z
b
I0bI1bI2bI3bE
b
Page 2
MC74AC352 MC74ACT352
5-2
FACT DATA
FUNCTIONAL DESCRIPTION
The MC74AC352/74ACT352 is a dual 4-input multiplexer.
It selects two bits of data from up to four sources under the
control of the common Select inputs (S0, S1). The two 4-input
multiplexer circuits have individual active LOW Enables (E
a
,
E
b
) which can be used to strobe the outputs independently.
When the Enables (E
a
, Eb) are HIGH, the corresponding
outputs (Z
a
, Zb) are forced HIGH.
The logic equations for the outputs are shown below:
Z
a
= E
a
•(I0a•S1•S
0+I1a•S1
•S
0
+
I
2a
•S1•S
0+I3a
•S1•S
0
)
Z
b
= E
b
•(I0b•S1•S
0+I1b•S1
•S
0
+
I
2b
•S1•S
0+I3b
•S1•S
0
)
The MC74AC352/74ACT352 can be used to move data
from a group of registers to a common output bus. The
particular register from which the date came would be
determined by the state of the Select inputs. A less obvious
application is as a function generator. The MC74AC352/
74ACT352 can generate two functions of three variables. This
is useful for implementing highly irregular random logic.
E
aI0a
I
3a
S
0
S
0
I
0b
I
1b
I
2b
I3bE
b
Z
a
Z
b
LOGIC DIAGRAM
Please note that this diagram is provided only for the understanding of logic
operations and should not be used to estimate propagation delays.
I
1a
I
2a
Page 3
MC74AC352 MC74ACT352
5-3
FACT DATA
MAXIMUM RATINGS*
Symbol Parameter Value Unit
V
CC
DC Supply Voltage (Referenced to GND) –0.5 to +7.0 V
V
in
DC Input Voltage (Referenced to GND) –0.5 to VCC +0.5 V
V
out
DC Output Voltage (Referenced to GND) –0.5 to VCC +0.5 V
I
in
DC Input Current, per Pin ±20 mA
I
out
DC Output Sink/Source Current, per Pin ±50 mA
I
CC
DC VCC or GND Current per Output Pin ±50 mA
T
stg
Storage Temperature –65 to +150 °C
* Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended
Operating Conditions.
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Typ Max Unit
′AC 2.0 5.0 6.0
VCCSupply Voltage
′ACT 4.5 5.0 5.5
V
Vin, V
out
DC Input Voltage, Output Voltage (Ref. to GND) 0 V
CC
V
VCC @ 3.0 V 150
tr, t
f
Input Rise and Fall Time (Note 1)
′AC Devices except Schmitt Inputs
VCC @ 4.5 V 40 ns/V
r
, t
f
′AC Devices except Schmitt Inputs
VCC @ 5.5 V 25
Input Rise and Fall Time (Note 2)
VCC @ 4.5 V 10
tr, t
f
Input Rise and Fall Time (Note 2)
′ACT Devices except Schmitt Inputs
VCC @ 5.5 V 8.0
ns/V
T
J
Junction Temperature (PDIP) 140 °C
T
A
Operating Ambient Temperature Range –40 25 85 °C
I
OH
Output Current — High –24 mA
I
OL
Output Current — Low 24 mA
1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times.
2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times.
Page 4
MC74AC352 MC74ACT352
5-4
FACT DATA
DC CHARACTERISTICS
74AC 74AC
Symbol
Parameter
V
CC
(V)
TA = +25°C
TA =
–40°C to +85°C
Unit
Conditions
Typ Guaranteed Limits
V
IH
Minimum High Level
3.0 1.5 2.1 2.1 V
OUT
= 0.1 V
Input Voltage
4.5 2.25 3.15 3.15 V or VCC – 0.1 V
5.5 2.75 3.85 3.85
V
IL
Maximum Low Level
3.0 1.5 0.9 0.9 V
OUT
= 0.1 V
Input Voltage
4.5 2.25 1.35 1.35 V or VCC – 0.1 V
5.5 2.75 1.65 1.65
V
OH
Minimum High Level
3.0 2.99 2.9 2.9 I
OUT
= –50 µA
Output Voltage
4.5 4.49 4.4 4.4 V
5.5 5.49 5.4 5.4
*VIN = VIL or V
IH
3.0 2.56 2.46
–12 mA
4.5 3.86 3.76
V
I
OH
–24 mA
5.5 4.86 4.76 –24 mA
V
OL
Maximum Low Level
3.0 0.002 0.1 0.1 I
OUT
= 50 µA
Output Voltage
4.5 0.001 0.1 0.1 V
5.5 0.001 0.1 0.1
*VIN = VIL or V
IH
3.0 0.36 0.44
12 mA
4.5 0.36 0.44
V
I
OL
24 mA
5.5 0.36 0.44 24 mA
I
IN
Maximum Input
Leakage Current
5.5
±0.1
±1.0
µA
VI = VCC, GND
I
OLD
†Minimum Dynamic
5.5 75 mA V
OLD
= 1.65 V Max
I
OHD
Output Current
5.5 –75 mA V
OHD
= 3.85 V Min
I
CC
Maximum Quiescent
Supply Current
5.5
8.080µA
VIN = VCC or GND
* All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V VCC.
Page 5
MC74AC352 MC74ACT352
5-5
FACT DATA
AC CHARACTERISTICS (For Figures and Waveforms — See Section 3)
74AC 74AC
Symbol
Parameter
VCC*
(V)
TA = +25°C
CL = 50 pF
TA = –40°C
to +85°C
CL = 50 pF
Unit
Fig.
No.
Min Typ Max Min Max
Propagation Delay
3.3 2.0 8.5 15.0 1.0 17.5
t
PLH
Sn to Z
n
5.0 2.0 6.5 11.0 1.0 12.5
ns
3-6
Propagation Delay
3.3 2.0 8.0 14.5 1.0 16.5
t
PHL
Sn to Z
n
5.0 2.0 6.0 11.0 1.0 12.0
ns
3-6
Propagation Delay
3.3 2.0 6.0 13.5 1.0 16.0
t
PLH
E
n
to Z
n
5.0 2.0 4.5 9.5 1.0 11.0
ns
3-6
Propagation Delay
3.3 2.0 5.5 11.0 1.0 12.5
t
PHL
E
n
to Z
n
5.0 2.0 4.0 8.0 1.0 9.0
ns
3-6
Propagation Delay
3.3 2.0 7.0 12.5 1.0 14.5
t
PLH
In to Z
n
5.0 2.0 5.0 9.0 1.0 10.5
ns
3-5
Propagation Delay
3.3 2.0 7.0 11.5 1.0 13.0
t
PHL
In to Z
n
5.0 2.0 5.0 8.5 1.0 10.0
ns
3-5
* Voltage Range 3.3 V is 3.3 V ±0.3 V.
Voltage Range 5.0 V is 5.0 V ±0.5 V.
DC CHARACTERISTICS
74ACT 74ACT
Symbol
Parameter
V
CC
(V)
TA = +25°C
TA =
–40°C to +85°C
Unit
Conditions
Typ Guaranteed Limits
V
IH
Minimum High Level
4.5 1.5 2.0 2.0
V
OUT
= 0.1 V
Input Voltage
5.5 1.5 2.0 2.0
V
or VCC – 0.1 V
V
IL
Maximum Low Level
4.5 1.5 0.8 0.8
V
OUT
= 0.1 V
Input Voltage
5.5 1.5 0.8 0.8
V
or VCC – 0.1 V
V
OH
Minimum High Level
4.5 4.49 4.4 4.4
I
OUT
= –50 µA
Output Voltage
5.5 5.49 5.4 5.4
V
*VIN = VIL or V
IH
4.5 3.86 3.76 V
–24 mA
5.5 4.86 4.76
I
OH
–24 mA
V
OL
Maximum Low Level
4.5 0.001 0.1 0.1
I
OUT
= 50 µA
Output Voltage
5.5 0.001 0.1 0.1
V
*VIN = VIL or V
IH
4.5 0.36 0.44 V
24 mA
5.5 0.36 0.44
I
OL
24 mA
I
IN
Maximum Input
Leakage Current
5.5
±0.1
±1.0
µA
VI = VCC, GND
∆I
CCT
Additional Max. ICC/Input 5.5 0.6 1.5 mA VI = VCC – 2.1 V
I
OLD
†Minimum Dynamic
5.5 75 mA V
OLD
= 1.65 V Max
I
OHD
Output Current
5.5 –75 mA V
OHD
= 3.85 V Min
I
CC
Maximum Quiescent
Supply Current
5.5
8.080µA
VIN = VCC or GND
* All outputs loaded; thresholds on input associated with output under test.
†Maximum test duration 2.0 ms, one output loaded at a time.
Page 6
MC74AC352 MC74ACT352
5-6
FACT DATA
AC CHARACTERISTICS (For Figures and Waveforms — See Section 3)
74ACT 74ACT
Symbol
Parameter
VCC*
(V)
TA = +25°C
CL = 50 pF
TA = –40°C
to +85°C
CL = 50 pF
Unit
Fig.
No.
Min Typ Max Min Max
Propagation Delay
t
PLH
Sn to Z
n
5.0
3.0
6.0
10.5
1.0
11.5ns3-6
Propagation Delay
t
PHL
Sn to Z
n
5.0
3.0
6.0
10.0
1.0
11.5ns3-6
Propagation Delay
t
PLH
E
n
to Z
n
5.0
2.0
4.5
8.0
1.0
8.5ns3-6
Propagation Delay
t
PHL
E
n
to Z
n
5.0
2.0
4.5
8.0
1.0
8.5ns3-6
Propagation Delay
t
PLH
In to Z
n
5.0
2.0
5.5
10.0
1.0
11.0ns3-5
Propagation Delay
t
PHL
In to Z
n
5.0
2.0
6.5
8.5
1.0
9.0ns3-5
* Voltage Range 5.0 V is 5.0 V ±0.5 V.
CAPACITANCE
Symbol Parameter
Value
Typ
Unit Test Conditions
C
IN
Input Capacitance 4.5 pF VCC = 5.0 V
C
PD
Power Dissipation Capacitance 50 pF VCC = 5.0 V
Page 7
MC74AC352 MC74ACT352
5-7
FACT DATA
OUTLINE DIMENSIONS
N SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B–05
ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
1 8
16 9
SEATING
PLANE
F
J
M
R
X 45
_
G
8 PLP
–B–
–A–
M
0.25 (0.010) B
S
–T–
D
K
C
16 PL
S
B
M
0.25 (0.010) A
S
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
_ _ _ _
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A–
B
F
C
S
H
G
D
J
L
M
16 PL
SEATING
1 8
916
K
PLANE
–T–
M
A
M
0.25 (0.010) T
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0 10 0 10
S 0.020 0.040 0.51 1.01
____
How to reach us:
USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: RMFAX0@email.sps.mot.com –TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “T ypicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
MC74AC352/D
*MC74AC352/D*
◊
Loading...