Datasheet MC33274AD, MC33274ADR2, MC33274AP, MC33272ADR2, MC33272AP Datasheet (Motorola)

  "  ! 

T

40° to +85°C

!       

Order this document by MC33272A/D

 

HIGH PERFORMANCE

OPERATIONAL

AMPLIFIERS

The MC33272/74 series of monolithic operational amplifiers are quality fabricated with innovative Bipolar design concepts. This dual and quad operational amplifier series incorporates Bipolar inputs along with a patented Zip–R–Trim element for input offset voltage reduction. The MC33272/74 series of operational amplifiers exhibits low input offset voltage and high gain bandwidth product. Dual–doublet frequency compensation is used to increase the slew rate while maintaining low input noise characteristics. Its all NPN output stage exhibits no deadband crossover distortion, large output voltage swing, and an excellent phase and gain margin. It also provides a low open loop high frequency output impedance with symmetrical source and sink AC frequency performance.

The MC33272/74 series is specified over –40° to +85°C and are available in plastic DIP and SOIC surface mount packages.

• Input Offset Voltage Trimmed to 100 µV (Typ)

• Low Input Bias Current: 300 nA

• Low Input Offset Current: 3.0 nA

• High Input Resistance: 16 MΩ

• Low Noise: 18 nV/ Hz

√

@ 1.0 kHz

• High Gain Bandwidth Product: 24 MHz @ 100 kHz

• High Slew Rate: 10 V/µs

• Power Bandwidth: 160 kHz

• Excellent Frequency Stability

• Unity Gain Stable: w/Capacitance Loads to 500 pF

• Large Output Voltage Swing: +14.1 V/ –14.6 V

• Low Total Harmonic Distortion: 0.003%

• Power Supply Drain Current: 2.15 mA per Amplifier

• Single or Split Supply Operation: +3.0 V to +36 V or ±1.5 V to ±18 V

• ESD Diodes Provide Added Protection to the Inputs

ORDERING INFORMATION

Op Amp

Function

Dual MC33272AD

Quad MC33274AD

Device

MC33272AP

MC33274AP Plastic DIP

Operating

Temperature Range

–

°

A

= –

°

Package

SO–8

Plastic DIP

SO–14

SEMICONDUCTOR

TECHNICAL DATA

8

1

P SUFFIX

PLASTIC PACKAGE

CASE 626

PIN CONNECTIONS

1

Output 1 V

Inputs 1

14

1

P SUFFIX

PLASTIC PACKAGE

CASE 646

2 3 4

V

EE

PIN CONNECTIONS

1

Output 1

2

Inputs 1

V

Inputs 2

Output 2

– +

3 4

CC

5

+ –

6

78

DUAL

PLASTIC PACKAGE

8 7

– +

(Top View)

6

–

+

5

Output 2

QUAD

PLASTIC PACKAGE

– +

4

1

+

23

–

8

1

D SUFFIX

CASE 751

(SO–8)

CC

Inputs 2

14

1

D SUFFIX

CASE 751A

(SO–14)

14

Output 4

13

Inputs 4

12

11

V

EE

10

Inputs 3

9

Output 3

MOTOROLA ANALOG IC DEVICE DATA

(Top View)

 Motorola, Inc. 1996 Rev 0

1

MC33272A MC33274A

MAXIMUM RATINGS

Rating Symbol Value Unit

Supply Voltage VCC to V Input Differential Voltage Range V Input Voltage Range V Output Short Circuit Duration (Note 2) t Maximum Junction Temperature T Storage Temperature T Maximum Power Dissipation P

NOTES: 1. Either or both input voltages should not exceed VCC or VEE.

2.Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded (see Figure 2).

EE

IDR

IR

SC

J

stg

D

+36 V (Note 1) V (Note 1) V

Indefinite sec

+150 °C

–60 to +150 °C

(Note 2) mW

DC ELECTRICAL CHARACTERISTICS (V

Characteristics Figure Symbol Min Typ Max Unit

Input Offset Voltage (RS = 10 Ω, VCM = 0 V, VO = 0 V)

(VCC = +15 V, VEE = –15 V)

TA = +25°C TA = –40° to +85°C

(VCC = 5.0 V, VEE = 0)

TA = +25°C

Average Temperature Coefficient of Input Offset Voltage

RS = 10 Ω, VCM = 0 V, VO = 0 V, TA = –40° to +85°C

Input Bias Current (VCM = 0 V, VO = 0 V)

TA = +25°C TA = –40° to +85°C

Input Offset Current (VCM = 0 V, VO = 0 V)

TA = +25°C TA = –40° to +85°C

Common Mode Input Voltage Range (∆VIO = 5.0 mV, VO = 0 V)

TA = +25°C

Large Signal Voltage Gain (VO = 0 V to 10 V, RL = 2.0 kΩ)

TA = +25°C TA = –40° to +85°C

Output Voltage Swing (VID = ±1.0 V)

(VCC = +15 V, VEE = –15 V)

RL = 2.0 kΩ RL = 2.0 kΩ RL = 10 kΩ RL = 10 kΩ

(VCC = 5.0 V, VEE = 0 V)

RL = 2.0 kΩ

RL = 2.0 kΩ Common Mode Rejection (Vin = +13.2 V to –15 V) 13 CMR 80 100 — dB Power Supply Rejection

VCC/VEE = +15 V/ –15 V, +5.0 V/ –15 V, +15 V/ –5.0 V

Output Short Circuit Current (VID = 1.0 V , Output to Ground)

Source Sink

Power Supply Current Per Amplifier (VO = 0 V)

(VCC = +15 V, VEE = –15 V)

TA = +25°C

TA = –40° to +85°C

(VCC = 5.0 V, VEE = 0 V)

TA = +25°C

= +15 V, VEE = –15 V, TA = 25°C, unless otherwise noted.)

CC

3 |VIO|

— —

—

3 ∆VIO/∆T

4, 5 I

|IIO|

6 V

7 A

8, 9, 12

10, 11

14, 15 PSR

16 I

17 I

VOL

VO+ VO– VO+ VO–

V V

CC

IB

ICR

OL OH

SC

— 2.0 —

— —

90 86

13.4 —

—

3.7

80 105 —

+25 –25

— —

—

0.1 —

—

300

—

3.0 —

VEE to (VCC –1.8)

100

—

13.9

–13.9

14

–14.7

— —

+37 –37

2.15 —

—

1.0

1.8

2.0

650 800

65 80

— —

—

–13.5

—

–14.1

0.2

5.0

— —

2.75

3.0

2.75

mV

µV/°C

nA

V

dB

V

dB

mA

2

MOTOROLA ANALOG IC DEVICE DATA

MC33272A MC33274A

AC ELECTRICAL CHARACTERISTICS (V

Characteristics Figure Symbol Min Typ Max Unit

Slew Rate

(Vin = –10 V to +10 V, RL = 2.0 kΩ, CL = 100 pF, AV = +1.0 V) Gain Bandwidth Product (f = 100 kHz) 19 GBW 17 24 — MHz AC Voltage Gain (RL = 2.0 kΩ, VO = 0 V, f = 20 kHz) 20, 21, 22 A Unity Gain Frequency (Open Loop) f Gain Margin (RL = 2.0 kΩ, CL = 0 pF) 23, 24, 26 A Phase Margin (RL = 2.0 kΩ, CL = 0 pF) 23, 25, 26 φ Channel Separation (f = 20 Hz to 20 kHz) 27 CS — –120 — dB Power Bandwidth (VO = 20 V Total Harmonic Distortion

(RL = 2.0 kΩ, f = 20 Hz to 20 kHz, VO = 3.0 V Open Loop Output Impedance (VO = 0 V, f = 6.0 MHz) 29 |ZO| — 35 — Ω Differential Input Resistance (VCM = 0 V) R Differential Input Capacitance (VCM = 0 V) C Equivalent Input Noise Voltage (RS = 100 Ω, f = 1.0 kHz) 30 e Equivalent Input Noise Current (f = 1.0 kHz) 31 i

= 2.0 kΩ, THD ≤ 1.0%) BW

pp, RL

= +15 V, VEE = –15 V, TA = 25°C, unless otherwise noted.)

CC

18, 33 SR 8.0 10 — V/µs

— 65 — dB — 5.5 — MHz — 12 — dB — 55 — Degrees

— 160 — kHz

— 16 — MΩ — 3.0 — pF — 18 — — 0.5 —

, AV = +1.0)

rms

VO

U

m

P

28 THD — 0.003 — %

IN IN

n

nV/ Hz√

pA/ Hz√

Figure 1. Equivalent Circuit Schematic

(Each Amplifier)

V

CC

–

V

in

+

V

in

+

Sections

BCD

V

O

+

V

EE

MOTOROLA ANALOG IC DEVICE DATA

3

MC33272A MC33274A

Figure 2. Maximum Power Dissipation

versus T emperature

2400

2000

1600

1200

800

400

0

D

P (MAX), MAXIMUM POWER DISSIPATION (mW)

MC33272P & MC33274P

MC33274D

MC33272D

0 20 40 60 80 100 120 140 160 180–60 –40 –20 TA, AMBIENT TEMPERATURE (°C)

Figure 4. Input Bias Current versus

Common Mode V oltage

400 350 300 250 200 150 100

IB

I , INPUT BIAS CURRENT (nA)

50

0

–16 –12 –8.0 –4.0 0 4.0 8.0 12 16

VCC = +15 V VEE = –15 V

°

C

TA = 25

VCM, COMMON MODE VOLTAGE (V)

Figure 3. Input Offset Voltage versus

Temperature for Typical Units

5.0

3.0

1.0 2

–1.0

–3.0

IO

V , INPUT OFFSET VOLTAGE (mV)

–5.0

–55 –25 0 25 50 75 100 125

1

VCC = +15 V VEE = –15 V VCM = 0 V

3

°

1. VIO > 0 @ 25

2. VIO = 0 @ 25

3. VIO < 0 @ 25

TA, AMBIENT TEMPERATURE (°C)

C

°

C

°

C

1

Figure 5. Input Bias Current

versus T emperature

600

VCC = +15 V

500

VEE = –15 V VCM = 0 V

400

300

200

100

IB

I , INPUT BIAS CURRENT (nA)

0

–55 –25 0 25 50 75 100 125

TA, AMBIENT TEMPERATURE (

°

C)

3

2

V

CC

VCC –0.5

VCC –1.0 VCC –1.5

VCC –2.0

VEE +1.0 VEE +0.5

ICR

V

EE

V , INPUT COMMON MODE VOLTAGE RANGE (V)

–55 –25 0 25 50 75 100 125

4

Figure 6. Input Common Mode V oltage

Range versus T emperature

V

CC

VCC = +5.0 V to +18 V

V

EE

TA, AMBIENT TEMPERATURE (

VEE = –5.0 V to –18 V

∆

VIO = 5.0 mV

VO = 0 V

°

C)

Figure 7. Open Loop Voltage Gain

versus T emperature

180

160

140

VCC = +15 V VEE = –15 V

120

100

VOL

A , OPEN LOOP VOL TAGE GAIN (X 1.0 kV/V)

–55 –25 0 25 50 75 100 125

Ω

RL = 2.0 k f = 10 Hz

∆

VO = –10 V to +10 V

TA, AMBIENT TEMPERATURE (°C)

MOTOROLA ANALOG IC DEVICE DATA

MC33272A MC33274A

Figure 8. Split Supply Output Voltage Swing

versus Supply V oltage

40

pp

, OUTPUT VOLT AGE (V )

O

V

TA = 25°C

30

RL = 10 k

Ω

20

RL = 2.0 k

Ω

10

0

0 5.0 10 15 20

VCC, VEE SUPPLY VOLTAGE (V)

Figure 10. Single Supply Output Saturation V oltage versus Load Resistance to Ground

V

CC

TA = 125°C

VCC –4.0

VCC –8.0

VCC –12

TA = 55

°

C

VCC = +5.0 V to +18 V RL to Gnd VEE = Gnd

Figure 9. Split Supply Output Saturation

V oltage versus Load Current

V

CC

VCC –1.0

VCC –2.0

VEE +2.0

VEE +1.0

, OUTPUT SA TURATION VOLT AGE (V)

sat

V

EE

V

CC

14.6

14.2

Source

TA = –55

TA = 125

°

C

TA = 25

Sink

TA = 25°C

TA = 125°C

VCC = +5.0 V to +18 V VEE = –5.0 V to –18 V

5.0 10 15 200

±

IL, LOAD CURRENT (

mA)

Figure 11. Single Supply Output Saturation

V oltage versus Load Resistance to V

15

TA = 25°C

°

C

°

C

TA = –55°C

CC

TA = 125°C

TA = 55°C

+0.2

, OUTPUT SA TURATION VOLT AGE (V)

+0.1

V

sat

Gnd

0

100 1.0 k 10 k 100 k 1.0 M

RL , LOAD RESISTANCE T O GROUND (k

Figure 12. Output Voltage versus Frequency

28 24

pp

20 16

VCC = +15 V

12

VEE = –15 V

Ω

RL = 2.0 k

8

, OUTPUT VOLT AGE (V )

O

V

AV = +1.0

4 0

1.0 k 10 k 1.0 M 1 0M100 k

TA = 25

°

C

≤

1.0%

THD =

f, FREQUENCY (Hz)

TA = 125 TA = +25 TA = –55

Ω

)

°

8.0

C

°

C

°

C

4.0

, OUTPUT SA TURATION VOLT AGE (V)

sat

V

0

10 100 1.0 k 100 k

TA = 25°C

TA = –55°C

TA = 125°C

RL, LOAD RESISTANCE T O VCC (

VCC = +15 V RL to V

CC

VEE = Gnd R

= 100 k

Fdbk

10 k

Ω

)

Ω

Figure 13. Common Mode Rejection

versus Frequency

120

VCC = +15 V

100

TA = 125

°

C

TA = –55°C

80

60

∆

V

CM

40

20

CMR = 20Log

CMR, COMMON MODE REJECTION (dB)

0

–

A

DM

+

∆

V

O

V

CM

X A

∆

DM

V

O

10 100 1.0 k 10 k 100 k 1.0 M

f, FREQUENCY (Hz)

VEE = –15 V VCM = 0 V

∆

VCM = ±1.5 V

MOTOROLA ANALOG IC DEVICE DATA

5

MC33272A MC33274A

Figure 14. Positive Power Supply Rejection

versus Frequency

120

TA = 125°C

100

80

60

40

20

+PSR = 20Log

+PSR, POWER SUPPLY REJECTION (dB)

0

10 100 1.0 k 10 k 100 k 1 .0 M

V

CC

–

A

DM

+

∆

V

O

V

EE

∆

VO/A

DM

∆

V

CC

f, FREQUENCY (Hz)

VCC = +15 V VEE = –15 V

∆

VCC = ±1.5 V

TA = –55°C

Figure 16. Output Short Circuit Current

versus T emperature

60

VCC = +15 V

50

Sink

40

Source

30

20

10

0

SC

–55 –25 0 25 50 75 100 125

|I |, OUTPUT SHORT CIRCUIT CURRENT (mA)

TA, AMBIENT TEMPERATURE (

VEE = –15 V

±

1.0 V

VID =

Ω

RL < 100

°

C)

Sink

Source

Figure 15. Negative Power Supply Rejection

versus Frequency

120

100

80

60

40

20

–PSR = 20Log

–PSR, POWER SUPPLY REJECTION (dB)

0

10 100 1.0 k 10 k 100 k 1.0 M

V

CC

–

A

DM

+

∆

V

O

V

EE

∆

VO/A

DM

∆

V

EE

TA = –55°C

TA = 125°C

f, FREQUENCY (Hz)

∆

VCC = ±1.5 V VCC = +15 V VEE = –15 V

Figure 17. Supply Current versus

Supply V oltage

11

10

9.0

8.0

7.0

6.0

5.0

CC

I , SUPPLY CURRENT (mA)

4.0

3.0 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20

TA = +125°C

°

C

TA = +25

°

C

TA = –55

VCC, |VEE| , SUPPLY VOLTAGE (V)

Figure 18. Normalized Slew Rate

versus T emperature

1.15

1.1

1.05

– +

∆

V

in

V

O

100 pF2.0 k

Ω

1.0 VCC = +15 V

0.95

SR, SLEW RATE (NORMALIZED)

0.9

0.85 –55 –25 0 25 50 75 100 125

VEE = –15 V

∆

Vin = 20 V

TA, AMBIENT TEMPERATURE (°C)

6

Figure 19. Gain Bandwidth Product

versus T emperature

50

40

30

20

10

GBW, GAIN BANDWIDTH PRODUCT (MHz)

0

–55 –25 0 25 50 75 100 125

TA, AMBIENT TEMPERATURE (°C)

VCC = +15 V VEE = –15 V f = 100 kHz

Ω

RL = 2.0 k CL = 0 pF

MOTOROLA ANALOG IC DEVICE DATA

MC33272A MC33274A

Figure 20. V oltage Gain and Phase

versus Frequency

25 20

15 10

5.0 0

–5.0

–10

V A , VOLTAGE GAIN (dB)

–15 –20

–25

100 k 1.0 M 10 M 100 M

VCC = +15 V VEE = –15 V RL = 2.0 k TA = 25°C

Gain

Phase

Ω

f, FREQUENCY (Hz)

Figure 22. Open Loop V oltage Gain and

Phase versus Frequency

20

10

0

VCC = +15 V VEE = –15 V V

–10

–20

VOL

A , OPEN LOOP VOLTAGE GAIN (dB)

–30

= 0 V

out

°

C

TA = 25 1A — Phase (RL = 2.0 k 2A — Phase (RL = 2.0 k 1B — Gain (RL = 2.0 k 2B — Gain (RL = 2.0 k

3.0 4.0 6.0 8.0 10 20 30 f, FREQUENCY (MHz)

2A

Ω

)

Ω

, CL = 300 pF)

Ω

)

Ω

, CL = 300 pF)

1A

1B

2B

80 100

120 140 160 180 200 220 240 260

280

25 20 15

TA = 25°C

10

CL = 0 pF

5.0 0

–5.0

–10

1A — Phase VCC = 18 V, VEE = –18 V

V

EXCESS PHASE (DEGREES)

φ,

2A — Phase VCC = 1.5 V, VEE = –1.5 V

A , VOLTAGE GAIN (dB)

–15

1B — Gain VCC = 18 V, VEE = –18 V

–20

2B — Gain VCC = 1.5 V, VEE = –1.5 V

–25

100 k 1.0 M 10 M 100 M

Figure 23. Open Loop Gain Margin and Phase

Margin versus Output Load Capacitance

100 120 140 160 180 200 220 240 260 280

12

10

VCC = +15 V VEE = –15 V

8.0

VO = 0 V

6.0

V

in

4.0

EXCESS PHASE (DEGREES)

2.0

φ

m

A , OPEN LOOP GAIN MARGIN (dB)

0

1.0 10 100 1000

Figure 21. Gain and Phase

versus Frequency

1A

2A

1B

2B

f, FREQUENCY (Hz)

Gain Margin

– +

2.0 k

CL, OUTPUT LOAD CAPACITANCE (pF)

V

O

Ω

C

L

Phase Margin

80 100 120 140 160 180 200

PHASE (DEGREES)

220

φ,

240

0

10

20

30

40

, PHASE MARGIN (DEGREES)

m

50

φ

Figure 24. Open Loop Gain Margin

versus T emperature

12

CL = 10 pF

10

8.0

CL = 100 pF

6.0

CL = 300 pF

4.0

2.0

m

A , OPEN LOOP GAIN MARGIN (dB)

0

–55 –25 0 25 50 75 100 125

CL = 500 pF

VCC = +15 V VEE = –15 V

TA, AMBIENT TEMPERATURE (°C)

MOTOROLA ANALOG IC DEVICE DATA

Figure 25. Phase Margin versus T emperature

60

50

40

30

20

, PHASE MARGIN (DEGREES)

m

10

φ

0

–55 –25 0 25 50 75 100 125

TA, AMBIENT TEMPERATURE (

CL = 10 pF

CL = 100 pF CL = 300 pF

CL = 500 pF

VCC = +15 V VEE =

°

C)

–15 V

7

MC33272A MC33274A

Figure 26. Phase Margin and Gain Margin

versus Differential Source Resistance

15

12

Phase Margin

9.0 VCC = +15 V

VEE = –15 V

6.0 RT = R1+R

VO = 0 V

3.0

TA = 25

m

A , GAIN MARGIN (dB)

0

V

2

°

C

–

R

1

in

+

R

2

V

O

1.0 10 100 1.0 k 10 k RT, DIFFERENTIAL SOURCE RESISTANCE (Ω)

Gain Margin

Figure 28. T otal Harmonic Distortion

versus Frequency

1.0 AV = +1000

AV = +100

0.1

AV = +10

0.01 AV = +1.0

VO = 2.0 V TA = 25

THD, TOT AL HARMONIC DISTORTION (%)

0.001 10 100 1.0 k 10 k 100 k

°

f, FREQUENCY (Hz)

pp

C

VCC = +15 V VEE = –15 V

60

50

40

30

20

, PHASE MARGIN (DEGREES)

m

10

φ

0

160

150

140

130

120

110

CS, CHANNEL SEPERA TION (dB)

100

100 1.0 k 10 k 100 k 1.0 M

Figure 29. Output Impedance versus Frequency

50

VCC = +15 V VEE = –15 V

Ω

40

VO = 0 V TA = 25

30

AV = 1000

20

O

10

|Z |, OUTPUT IMPEDANCE ( )

0

10 k 100 k 1.0 M 10 M

Figure 27. Channel Separation

versus Frequency

Driver Channel VCC = +15 V VEE = –15 V RL = 2.0 k

∆

TA = 25

f, FREQUENCY (Hz)

°

C

AV = 100

AV = 10

f, FREQUENCY (Hz)

Ω

VOD = 20 V

°

C

AV = 1.0

pp

Figure 30. Input Referred Noise V oltage

versus Frequency

50

nV/ Hz√

40

30

+ –

Input Noise Voltage T est Circuit

20

10

n

e , INPUT REFERRED NOISE VOL TAGE ( )

VCC = +15 V VEE = –15 V

°

C

TA = 25

0

10 100 1.0 k 10 k 100 k

f, FREQUENCY (Hz)

8

Figure 31. Input Referred Noise Current

versus Frequency

2.0

1.8

V

O

pA/ Hz√

1.6

1.4

1.2

1.0

0.8

0.6 VCC = +15 V

0.4 VEE = –15 V

0.2

0

10 100 1.0 k 10 k 100 k

n

i , INPUT REFERRED NOISE CURRENT ( )

TA = 25

°

C

f, FREQUENCY (Hz)

Input Noise Current Circuit

+

R

S

–

(RS = 10 k

V

Ω)

O

MOTOROLA ANALOG IC DEVICE DATA

MC33272A MC33274A

Figure 32. Percent Overshoot versus

Load Capacitance

60

VCC = +15 V

VEE = –15 V

50

40

30

20

PERCENT OVERSHOOT (%)

10

0

10 100 1.0 k

RL = 2.0 k

TA = 25°C

Ω

CL, LOAD CAPACITANCE (pF)

Figure 33. Noninverting Amplifier Slew Rate

for the MC33274

VCC = +15 V VEE = –15 V AV = +1.0

Ω

RL = 2.0 k CL = 100 pF

°

C

TA = 25

O

V , OUTPUT VOLTAGE (5.0 V/DIV)

µ

t, TIME (2.0

s/DIV)

Figure 35. Small Signal Transient Response

for MC33274

VCC = +15 V VEE = –15 V AV = +1.0 RL = 2.0 k CL = 300 pF TA = 25

Ω

°

C

Figure 34. Noninverting Amplifier Overshoot

for the MC33274

VCC = +15 V VEE = –15 V AV = +1.0

Ω

RL = 2.0 k

O

V , OUTPUT VOLTAGE (5.0 V/DIV)

TA = 25°C

t, TIME (2.0 ns/DIV)

Figure 36. Large Signal Transient Response

for MC33274

VCC = +15 V VEE = –15 V AV = +1.0 RL = 2.0 k CL = 300 pF

°

C

TA = 25

CL = 100 pF

φ

CL =

Ω

O

V , OUTPUT VOLTAGE (50 mV/DIV)

t, TIME (2.0

µ

s/DIV) t, TIME (1.0 µs/DIV)

MOTOROLA ANALOG IC DEVICE DATA

O

V , OUTPUT VOLTAGE (5.0 V/DIV)

9

NOTE 2

–T–

SEATING PLANE

H

MC33272A MC33274A

OUTLINE DIMENSIONS

58

–B–

14

F

–A–

C

N

D

G

0.13 (0.005) B

K

M

T

P SUFFIX

PLASTIC PACKAGE

CASE 626–05

ISSUE K

L

J

M

A

M

NOTES:

1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL.

2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS).

3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

DIM MIN MAX MIN MAX

A 9.40 10.16 0.370 0.400 B 6.10 6.60 0.240 0.260 C 3.94 4.45 0.155 0.175 D 0.38 0.51 0.015 0.020 F 1.02 1.78 0.040 0.070

G 2.54 BSC 0.100 BSC

H 0.76 1.27 0.030 0.050 J 0.20 0.30 0.008 0.012 K 2.92 3.43 0.115 0.135 L 7.62 BSC 0.300 BSC

M ––– 10 ––– 10

N 0.76 1.01 0.030 0.040

INCHESMILLIMETERS

__

A

C

E

B

A1

D SUFFIX

PLASTIC PACKAGE

CASE 751–05

(SO–8)

ISSUE R

D

58

0.25MB

1

H

4

e

M

h

X 45

_

q

C

A

SEATING PLANE

0.10

L

B

SS

A0.25MCB

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.

2. DIMENSIONS ARE IN MILLIMETERS.

3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION.

MILLIMETERS

DIM MIN MAX

A 1.35 1.75

A1 0.10 0.25

B 0.35 0.49 C 0.18 0.25 D 4.80 5.00 E

3.80 4.00

1.27 BSCe

H 5.80 6.20 h

0.25 0.50

L 0.40 1.25

0 7

q

__

10

MOTOROLA ANALOG IC DEVICE DATA

MC33272A MC33274A

OUTLINE DIMENSIONS

P SUFFIX

PLASTIC PACKAGE

CASE 646–06

ISSUE L

14 8

B

17

A F

N

SEATING

HG D

PLANE

C

K

L

J

M

NOTES:

1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION.

2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL.

3. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

4. ROUNDED CORNERS OPTIONAL.

DIM MIN MAX MIN MAX

A 0.715 0.770 18.16 19.56 B 0.240 0.260 6.10 6.60 C 0.145 0.185 3.69 4.69 D 0.015 0.021 0.38 0.53 F 0.040 0.070 1.02 1.78 G 0.100 BSC 2.54 BSC H 0.052 0.095 1.32 2.41 J 0.008 0.015 0.20 0.38 K 0.115 0.135 2.92 3.43 L 0.300 BSC 7.62 BSC M 0 10 0 10

____

N 0.015 0.039 0.39 1.01

MILLIMETERSINCHES

–T–

SEATING PLANE

–A–

14 8

G

D 14 PL

0.25 (0.010) A

D SUFFIX

PLASTIC PACKAGE

CASE 751A–03

(SO–14) ISSUE F

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

–B–

71

M

7 PL

P

M

0.25 (0.010) B

C

R X 45

K

S

B

T

S

M

_

M

F

J

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.

DIM MIN MAX MIN MAX

A 8.55 8.75 0.337 0.344 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 0.050 BSC J 0.19 0.25 0.008 0.009 K 0.10 0.25 0.004 0.009 M 0 7 0 7

____

P 5.80 6.20 0.228 0.244 R 0.25 0.50 0.010 0.019

INCHESMILLIMETERS

MOTOROLA ANALOG IC DEVICE DATA

11

MC33272A MC33274A

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

How to reach us: USA/EUROPE /Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF AX0@email.sps.mot.com – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T ., Hong Kong. 852–26629298

12

◊

MOTOROLA ANALOG IC DEVICE DATA

MC33272A/D

*MC33272A/D*

Datasheet MC33274AD, MC33274ADR2, MC33274AP, MC33272ADR2, MC33272AP Datasheet (Motorola)

Specifications and Main Features

Frequently Asked Questions

User Manual