Datasheet MC33206D, MC33206P, MC33207D Datasheet (Motorola)

 

Dual

T

105°C

Quad

Order this document by MC33206/D




 
  


The MC33206/7 family of operational amplifiers provide rail–to–rail
operation on both the input and output. The inputs can be driven as high as
200 mV beyond the supply rails without phase reversal on the outputs and
the output can swing within 50 mV of each rail. This rail–to–rail operation
enables the user to make full use of the supply voltage range available. It is
designed to work at very low supply voltages (±0.9 V) yet can operate with a
single supply of up to 12 V and ground. Output current boosting techniques
provide a high output current capability while keeping the drain current of the
amplifier to a minimum.

The MC33206/7 has an enable mode that can be controlled externally.
The typical supply current in the standby mode is <1.0 µA (V
The addition of an enable function makes this amplifier an ideal choice for
power sensitive applications, battery powered equipment (ins trumentation and
monitoring), portable telecommunication, and sample–and–hold applications.

• Standby Mode (I

≤1.0 µA, Typ)

D

• Low Voltage, Single Supply Operation

(1.8 V and Ground to 12 V and Ground)

• Rail–to–Rail Input Common Mode Voltage Range

• Output Voltage Swings within 50 mV of both Rails

• No Phase Reversal on the Output for Over–Driven Input Signals

• High Output Current (I

• Low Supply Current (I

= 80 mA, Typ)

SC

= 0.9 mA, Typ)

D

• 600 Ω Output Drive Capability

• Typical Gain Bandwidth Product = 2.2 MHz

Enable

= Gnd).

LOW VOLTAGE

RAIL–TO–RAIL

OPERATIONAL AMPLIFIERS

SEMICONDUCTOR

TECHNICAL DATA

MC33206

P SUFFIX

PLASTIC PACKAGE

14

Output 1

Inputs 1

Enable 1

16

1

14

1

N.C.

1
2

N.C.

3
4

1

7

V

EE

(Dual, Top View)

MC33207

1

CASE 646

D SUFFIX

PLASTIC PACKAGE

CASE 751A

(SO–14)

N.C.

14

V

13

CC

Output 2

12
11

2

PLASTIC PACKAGE

Inputs 2

105

96

Enable 2

8

N.C.

P SUFFIX

CASE 648

ORDERING INFORMATION

Operational

Amplifier Function

This document contains information on a new product. Specifications and information herein
are subject to change without notice.

MOTOROLA ANALOG IC DEVICE DATA

Device

MC33206D
MC33206P
MC33207D
MC33207P Plastic DIP

Operating

Temperature Range

–

°

= –40 ° to +

A

°

Package

SO–14

Plastic DIP

SO–16

 Motorola, Inc. 1996 Rev 0

16

1

Output 1

1

V

CC

Output 2

2
3
4

8

Inputs 1

Inputs 2 2

Enable 2, 3

1

(Quad, Top View)

D SUFFIX

PLASTIC PACKAGE

CASE 751B

(SO–16)

Enable 1, 4

16

Output 4

15
14

4

3

13
125
116
107

9

Inputs 4

V

EE

Inputs 3

Output 3

1

MC33206 MC33207

MAXIMUM RATINGS

Rating Symbol Value Unit

Supply Voltage (VCC to VEE) V
ESD Protection Voltage at any Pin

Human Body Model
Voltage at any Device Pin V
Input Differential Voltage Range V
Common Mode Input Voltage Range (Note 2) V

Output Short Circuit Duration (Note 3) t
Maximum Junction Temperature T
Storage Temperature Range T
Maximum Power Dissipation P

NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back–to–back

diodes. For additional differential input voltage range, use current limiting resistors in series
with the input pins.

2.The common–mode input voltage range of each amplifier is limited by diodes connected from
the inputs to both power supply rails. Therefore, the voltage on either input must not exceed
either supply rail by more than 500 mV.

3.Power dissipation must be considered to ensure maximum junction temperature (TJ) is not
exceeded.

4.ESD data available upon request.

V

S

ESD

DP

IDR

CM

s

J

stg

D

13 V

2,000 V

VS ± 0.5 V

(Note 1) V

VCC + 0.5 to

VEE – 0.5

(Note 3) sec

+150 °C

–65 to +150 °C

(Note 3) mW

V

DC ELECTRICAL CHARACTERISTICS (V

= 5.0 V, VEE = 0 V, V

CC

= 5.0 V, TA = 25°C, unless otherwise noted.)

Enable

Characteristic Figure Symbol Min Typ Max Unit

Input Offset Voltage (VCM 0 to 0.5 V, VCM 1.0 to 5.0 V)

MC33206: TA = 25°C

MC33201: TA = –40° to +105°C

MC33207: TA = 25°C

MC33202: TA = –40° to +105°C

Input Offset Voltage Temperature Coefficient (RS = 50 Ω)

– V

IO

–
–
–
–

0.5

1.0

0.5

1.0

8.0
11

10
13

– ∆VIO/∆T – 2.0 – µV/°C

TA = –40° to +105°C

Input Bias Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V)

TA = 25°C

–

TA = –40° to +105°C

Input Offset Current (VCM = 0 to 0.5 V, VCM = 1.0 to 5.0 V)

– IIO
TA = 25°C
TA = –40° to +105°C

Common Mode Input Voltage Range – V

Large Signal Voltage Gain (VCC = 5.0 V, VEE = –5.0 V)

– A
RL = 10 kΩ
RL = 600 Ω

Output Voltage Swing (VID = ±0.2 V)

–
RL = 10 kΩ
RL = 10 kΩ
RL = 600 Ω
RL = 600 Ω

IIB

ICR

VOL

V

OH

V

OL

V

OH

V

OL

–
–

–
–

–

V

EE

50
25

4.85
–

4.75
–

80

100

5.0
10

VCC + 0.2
VEE – 0.2

300
250

4.95

0.05

4.85

0.15

200
250

50

100

V

CC

–

–
–

–

0.15
–

0.25

Common Mode Rejection (Vin = 0 to 5.0 V) – CMR 60 90 – dB
Power Supply Rejection Ratio

VCC/VEE = 5.0 V/Gnd to 3.0 V/Gnd

Output Short Circuit Current (Source and Sink) – I

– PSRR

PSR

SC

–

66

25
92

500

–

50 80 – mA

mV

nA

nA

V

kV/V

V

µV/V

dB

2

MOTOROLA ANALOG IC DEVICE DATA

MC33206 MC33207

DC ELECTRICAL CHARACTERISTICS (continued) (V

Characteristic UnitMaxTypMinSymbolFigure

Power Supply Current (VO = 2.5 V, TA = –40° to +105°C,

per Amplifier)

MC33206: V

MC33206: V

MC33207: V

MC33207: V

Enable Input Voltage (per Amplifier)

Enabled – Amplifier “On”
Disabled – Amplifier “Off” (Standby)

Enable Input Current (Note 5) (per Amplifier)

V
V
V
V

NOTE: 5.External control circuitry must provide for an initial turn–off transient of <10 µA.

Enable
Enable
Enable
Enable

= 12 V
= 5.0 V
= 1.8 V
= Gnd

AC ELECTRICAL CHARACTERISTICS (V

Slew Rate (VS = ±2.5 V , VO = –2.0 to +2.0 V,

RL = 2.0 kΩ, AV = 1.0)
Gain Bandwidth Product (f = 100 kHz) – GBW – 2.2 – MHz
Phase Margin (RL = 600 Ω, CL = 0 pF) –
Gain Margin (RL = 600 Ω, CL = 0 pF) – A
Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) – CS – 90 – dB
Power Bandwidth (VO = 4.0 Vpp, RL = 600 Ω, THD ≤ 1%) – BW
Total Harmonic Distortion (RL = 600 Ω, VO = 1.0 Vpp, AV = 1.0)

f = 1.0 kHz
f = 10 kHz

Open Loop Output Impedance

(VO = 0 V, f = 2.0 MHz, AV = 10)
Differential Input Resistance (VCM = 0 V) – R
Differential Input Capacitance (VCM = 0 V) – C
Equivalent Input Noise Voltage (RS = 100 Ω)

f = 10 Hz

f = 1.0 kHz
Equivalent Input Noise Current

f = 10 Hz

f = 1.0 kHz
Time Delay for Device to Turn On – t
Time Delay for Device to Turn Off – t

= 5.0 Vdc

Enable

= Gnd (Standby)

Enable

= 5.0 Vdc

Enable

= Gnd (Standby)

Enable

= 5.0 V, VEE = 0 V, V

CC

Characteristic Figure Symbol Min Typ Max Unit

= 5.0 V, VEE = 0 V, V

CC

– I

– V

– I

Enable

– SR 0.5 1.0 – V/µs

–

– ZO – 100 – Ω

– e

– i

= 5.0 V, TA = 25°C, unless otherwise noted.)

Enable

D

–
–
–
–

Enable

Enable

= 5.0 V, TA = 25°C, unless otherwise noted.)

O

M

M

P

THD

in
in
n

n

on
off

–
–

–
–
–
–

– 65 – Deg
– 12 – dB

– 28 – kHz

–
–

– 200 – kΩ
– 8.0 – pF

–
–

–
–

– 10 – µs
– 2.0 – µs

0.8

0.5

1.5

0.5

VEE + 1.8
VEE + 0.3

2.5

2.2

0.8
0

0.002

0.008

25
20

0.8

0.2

1.125

6.0

2.25

6.0

–
–

–
–
–
–

–
–

–
–

pA/
–
–

mA

µA

mA

µA

V

µA

%

nV/

Hz

Hz

MOTOROLA ANALOG IC DEVICE DATA

3

V

CC

Enable

MC33206 MC33207

Figure 1. Circuit Schematic

(Each Amplifier)

V

CC

Vin –

Vin +

V

CC

V

CC

V

EE

4000
3500
3000
2500
2000
1500
1000

, MAXIMUM POWER DISSIPATION (mW)

500

0

D(max)

P

–60 –30

This device contains 96 active transistors (each amplifier).

Figure 2. Maximum Power Dissipation

versus T emperature

16 Pin DIP

14 Pin DIP

SO–14/SO–1

6

0 30 60 90 120 150

TA, AMBIENT TEMPERATURE (

°

C)

Figure 3. Input Offset Voltage Distribution

40
35
30
25
20

15
10

PERCENT AGE OF AMPLIFIERS (%)

5.0
0

–10 0 4.0 8.0 10–2.0 2.0 6.0–6.0–8.0 –4.0

360 amplifiers tested
from 3 wafer lots

VCC = 5.0 V
VEE = Gnd
TA = 25
DIP Package

VIO, INPUT OFFSET VOLTAGE (mV)

°

C

4

MOTOROLA ANALOG IC DEVICE DATA

MC33206 MC33207

–

–

+

+

Figure 4. Input Offset Voltage

T emperature Coefficient Distribution

50

360 amplifiers tested

40

30

20

10

PERCENT AGE OF AMPLIFIERS (%)

0

–50 0 20 40 50–10 10 30–30–40 –20

TC

, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (µV/°C)

V

IO

from 3 wafer lots

VCC = 5.0 V
VEE = Gnd
TA = 25
DIP Package

°

C

200

160

120

80

, INPUT BIAS CURRENT (nA)

40

IB

I

0

–55 –40 –25 0 25 70 85 125

Figure 6. Input Bias Current

versus Common Mode V oltage

150
100

50

0

–50
–100
–150

, INPUT BIAS CURRENT (nA)

IB

I

–200
–250

0 6.0 8.0 10 12 105

2.0 4.0
VCM, INPUT COMMON MODE VOLTAGE (V)

VCC = 12 V
VEE = Gnd

°

C

TA = 25

300

260

220

180

VCC = 5.0 V
VEE = Gnd

140

, OPEN LOOP VOL TAGE GAIN (kV/V)
A

RL = 600

∆

VOL

100

–55 –40 –25 0 25 70 85 125

Figure 5. Input Bias Current

versus T emperature

VCM = 0 V to 0.5 V

VCM > 1.0 V

TA, AMBIENT TEMPERATURE (

Figure 7. Open Loop Voltage Gain

versus T emperature

Ω

VO = 0.5 V to 4.5 V

TA, AMBIENT TEMPERATURE (

VCC = 5.0 V
VEE = Gnd

°

°

C)

C)

Figure 8. Output Voltage Swing

versus Supply V oltage

12

RL = 600

Ω

TA = 25°C

10

8.0

6.0

4.0

,OUTPUT VOLTAGE (Vpp)

2.0

O

V

0

±

1.0

±

2.0 105.0
VCC,

±

3.0



VEE

SUPPLY VOLTAGE (V)

±

4.0

MOTOROLA ANALOG IC DEVICE DATA

Figure 9. Output Saturation Voltage

versus Load Current

V

TA = –55°C

TA = 125°C

TA = 25°C

VCC = 5.0 V
VEE = –5.0 V

, OUTPUT SA TURATION VOLTAGE (V)

TA = 125°C

SAT

V

±

5.0

±

6.0

01520

IL, LOAD CURRENT (mA)

TA = 25°C

TA = –55°C

CC

VCC

VCC

VEE

VEE

V

EE

5

MC33206 MC33207

12

9.0

6.0
VCC = 6.0 V

VEE = –6.0 V

, OUTPUT VOLTAGE (Vpp)

3.0

O

V

0

1.0 k 100 k 1.0 M10 k

RL = 600
AV = 1.0

°

TA = 25

Ω

C

Figure 12. Power Supply Rejection

120

100

80

60

40

VCC = 6.0 V

20

VEE = –6.0 V

°

to +125°C

TA = –55

PSR, POWER SUPPLY REJECTION (dB)

0

10

100 1.0 k 10 k 100 k 1.0 M

Figure 10. Output Voltage

versus Frequency

f, FREQUENCY (Hz)

versus Frequency

PSR+

PSR–

f, FREQUENCY (Hz)

Figure 11. Common Mode Rejection

versus Frequency

100

80

60

40

VCC = 6.0 V
VEE = –6.0 V

20

CMR, COMMON MODE REJECTION (dB)

0

10

°

to +125°C

TA = –55

100 1.0 k 10 k 100 k 1.0 M

f, FREQUENCY (Hz)

Figure 13. Output Short Circuit Current

versus Output Voltage

100

Source

80

60

40

20

, OUTPUT SHORT CIRCUIT CURRENT (mA)

SC

0

I

0 1.0 2.0 3.0 4.0 5.0 6.0

Sink



V



, OUTPUT VOLTAGE (V)

out

VCC = 6.0 V
VEE = –6.0 V
TA = 25

°

C

150

125

100

75

50

25

, OUTPUT SHORT CIRCUIT CURRENT (mA)

SC

I

6

Figure 14. Output Short Circuit Current

versus T emperature

VCC = 5.0 V
VEE = Gnd

Source

Sink

0

TA, AMBIENT TEMPERATURE (°C)

2.0

1.6

1.2

0.8

0.4

, SUPPLY CURRENT PER AMPLIFIER (mA)

CC

I

Figure 15. Supply Current per Amplifier

versus Supply V oltage with No Load

TA = 125°C

TA = 25°C

TA = –55°C

0

±

±

1.0

±

0

2.0

VCC, VEE

±

3.0

±

, SUPPLY VOLTAGE (V)

MOTOROLA ANALOG IC DEVICE DATA

4.0

±

5.0

±

.0–55 –40 –25 25 70 1250 85 105

MC33206 MC33207

Figure 16. Slew Rate

versus T emperature

2.0

VCC = 2.5 V
VEE = –2.5 V

±

2.0 V

VO =

1.5

µ

1.0

SR, SLEW RA TE (V/ s)

0.5

0

–55 –40 –25 25 70 1250 85 105 –55 –40 –25 25 70 1250 85 105

TA, AMBIENT TEMPERATURE (°C)

+Slew Rate

–Slew Rate

4.0

3.0

2.0

1.0

GBW, GAIN BANDWIDTH PRODUCT (MHz)

0

Figure 18. V oltage Gain and Phase

versus Frequency

70

50

VS = ±6.0 V

°

C

TA = 25

Ω

RL = 600

40

80

70

50

Figure 17. Gain Bandwidth Product

versus T emperature

VCC = 2.5 V
VEE = –2.5 V
f = 100 kHz

TA, AMBIENT TEMPERATURE (

Figure 19. V oltage Gain and Phase

versus Frequency

°

C)

CL = 0 pF
TA = 25
RL = 600

40

°

C

Ω

80

30

10

1A – Phase, CL = 0 pF
1B – Gain, CL = 0 pF

–10

2A – Phase, CL = 300 pF
2B – Gain, CL = 300 pF

VOL

A , OPEN LOOP VOLTAGE GAIN (dB)

–30

10 k 100 k 1.0 M 10 M

f, FREQUENCY (Hz)

2A

2B

1B

Figure 20. Gain and Phase Margin

versus T emperature

70
60
50

VCC = 6.0 V

40

VEE = –6.0 V

Ω

RL = 600

30

CL = 100 pF

20

, PHASE MARGIN (DEGREES)

M

10

O

0

TA, AMBIENT TEMPERATURE (

Phase Margin

Gain Margin

°

C)

1A

120

160

200

240

30

10

1A – Phase, VS = ±6.0 V
1B – Gain, VS =

–10

, EXCESS PHASE (DEGREES)

O

2A – Phase, VS =

VOL

2B – Gain, VS =

A , OPEN LOOP VOLTAGE GAIN (dB)

–30

10 k 100 k 1.0 M 10 M

versus Differential Source Resistance

70
60
50
40
30

, GAIN MARGIN (dB)

20

A

10
0

75

60

VCC = 6.0 V

45

VEE = –6.0 V
TA = 25

30

M

15

, PHASE MARGIN (DEGREES)

M

O

0

2A

1B

±

6.0 V

±

1.0 V

±

1.0 V

f, FREQUENCY (Hz)

2B

Figure 21. Gain and Phase Margin

Phase Margin

°

C

Gain Margin

100 1.0 k 10 k 100 k–55 –40 –25 25 70 1250 85 105 10

RT, DIFFERENTIAL SOURCE RESISTANCE (Ω)

1A

120

160

200

240

75

60

45

30

15

0

MOTOROLA ANALOG IC DEVICE DATA

7

MC33206 MC33207

Figure 22. Gain and Phase Margin

versus Capacitive Load

80
70

Phase Margin

60

Gain Margin

50
40
30
20

, PHASE MARGIN (DEGREES)

M

10

O

0

10 100 1.0 k

CL, CAPACITIVE LOAD (pF)

VCC = 6.0 V
VEE = –6.0 V

Ω

RL = 600
AV = 100

°

C

TA = 25

Figure 24. Channel Separation

versus Frequency

150

120

90

60

VCC = 6.0 V
VEE = –6.0 V

30

VO = 8.0 Vpp

CS, CHANNEL SEPARATION (dB)

0

100 1.0 k 10 k

TA = 25

°

C

f, FREQUENCY (Hz)

AV = 100

AV = 10

16
14
12
10

8.0

6.0

4.0

2.0
0

5.0

4.0

3.0

2.0

, GAIN MARGIN (dB)

, OUTPUT VOL TAGE (Vpp)

M

A

O

1.0

V

0

10

1.0

0.1

0.01

THD, TOT AL HARMONIC DISTORTION (%)

0.001

Figure 23. Output Voltage

versus Load Resistance

VCC = 5.0 Vdc

VEE = Gnd
CL = 0 pF
AV = 1.0

°

C

TA = 25

100 1.0 k 10 k 100 k10

RL, LOAD RESISTANCE

VCC = 2.0 Vdc

Figure 25. T otal Harmonic Distortion

versus Frequency

VCC = 5.0 V

°

TA = 25
VO = 2.0 Vpp

AV = 1000
AV = 100

AV = 10

AV = 1.0

10 100 1.0 k 100 k

VEE = –5.0 V

C

RL = 600

f, FREQUENCY (Hz)

Ω

10 k

Figure 26. Equivalent Input Noise V oltage

and Current versus Frequency

50

40

30

20

10

0

n

10

e , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz)

Noise Voltage

Noise Current

100 10 k 100 k

1.0 k

f, FREQUENCY (Hz)

VCC = 6.0 V
VEE = –6.0 V
TA = 25

8

5.0

4.0

°

C

3.0

2.0

1.0

0

n

i , INPUT REFERRED NOISE CURRENT (pA/ Hz)

MOTOROLA ANALOG IC DEVICE DATA

MC33206 MC33207

GENERAL INFORMATION

The MC33206/7 family of operational amplifiers are
unique in their ability to swing rail–to–rail on both the input
and the output with a completely bipolar design. This offers
low noise, high output current capability and a wide common
mode input voltage range even with low supply voltages.
Operation is guaranteed over an extended temperature
range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and
ground.

Since the common mode input voltage range extends from
VCC to VEE, it can be operated with either single or split
voltage supplies. The MC33206/7 are guaranteed not to latch
or phase reverse over the entire common mode range,
however, the inputs should not be allowed to exceed
maximum ratings.

CIRCUIT INFORMATION

Rail–to–rail performance is achieved at the input of the
amplifiers by using parallel NPN–PNP differential input
stages. When the inputs are within 800 mV of the negative
rail, the PNP stage is on. When the inputs are more than
800 mV greater than VEE, the NPN stage is on. This
switching of input pairs will cause a reversal of input bias
currents (see Figure 6). Also, slight differences in offset
voltage may be noted between the NPN and PNP pairs.
Cross–coupling techniques have been used to keep this
change to a minimum.

In addition to its rail–to–rail performance, the output stage
is current boosted to provide 80 mA of output current,
enabling the op amp to drive 600 Ω loads. Because of this
high output current capability, care should be taken not to
exceed the 150°C maximum junction temperature.

Enable Function

The MC33206/07 enable pins allow the user to externally
control the device. (Refer to the Pin Diagram on the first page
of this data sheet for enable pin connections.) If the enable
pins are pulled low (Gnd) each amplifier (MC33206) and
amplifier pair (MC33207) will be disabled. When the enable
pins are at a logic high (V
will turn “on”. Refer to the data sheet characteristics for the
required levels needed to change logical state.

The time to change states (from device “on” to “off” and
“off” to “on”) is defined as the time delay. The Circuit in
Figure 27 is used to measure ton and t
measurements are shown in Figures 28 and 29. When the
device is turned off (V

Enable

shut off disabling the amplifier.

Figure 27. Test Circuit for ton and t

MC33206

2.0 V

V

Enable

ton t

off

≥ VEE = 1.8 V) the amplifiers

Enable

. Typical ton and t

off

= Gnd) an internal regulator is

off

V

CC

2.0 k

V

out

ton t

off

off

Figure 28. ton Response

(2.0 V/DIV)

in

(1.0 V/DIV), V

O

V

ton, TIME (2.0 µs/DIV)

(2.0 V/DIV)

in

(1.0 V/DIV), V

O

V

Figure 29. t

t

, TIME (2.0 µs/DIV)

off

Response

off

Low V oltage Operation

The MC33206/07 will operate at supply voltages down to

1.8 V and ground. Since this device is a rail–to–rail on both
the input and output, one can be assured of continued
operation in battery applications when battery voltages drop
to low voltage levels. This is called End of Discharge (see
Figure 30). Now, the user can select a minimum quantity of
batteries best suited for the particular design depending on
the type of battery chosen. This will minimize part count in
many designs.

Figure 30. T ypical Battery Characteristics

Type Operating Voltage End of Discharge

Alkaline 1.5 V 0.9 V

NiCd 1.2 V 1.0 V
NiMh 1.2 V 1.0 V

Silver Oxide 1.6 V 1.3 V

Lithium Ion 3.6 V 2.5 V

Compensating for Output Capacitance

The combination of device output impedance and
increasing capacitive loading will cause phase delay
(reducing the phase margin) in any amplifier (Figure 22). If
the loading is excessive, the resulting response can be circuit
oscillation. In other words, an amplifier can become unstable
when the phase becomes greater than 180 degrees before
the open loop gain drops to unity gain. Figures 18 and 19
show this situation as frequency increases for a given load.
The MC33206/7 can typically drive up to 300 pF loads at
unity gain without oscillating.

MOTOROLA ANALOG IC DEVICE DATA

9

MC33206 MC33207

Figure 31. Capacitive Loads Compensation

R

f

C

X

R

O

V

in

C

L

R

L

There are several ways to compensate for this
phenomena. Adding series resistance to the output is one
way, but not an ideal solution. A dc voltage error will occur at
the output. A better design solution to compensate for higher
capacitive loads would be to use the circuit in Figure 31. This
design helps to counteract the loss of phase margin by taking
the high frequency output signal and feeding it back into the
amplifier inverting input. This technique helps to overcome
oscillation due to a highly capacitive load. Keep in mind that
compensation will have the affect of lowering the Gain
Bandwidth Product (GPW). The values of CX and R0, are
determined experimentally. Typical CX and CL will be the
same value.

Figure 32. Noninverting Amplifier Slew Rate Figure 33. Small Signal Transient Response

VCC = 6.0 V
VEE = –6.0 V

Ω

RL = 600
CL = 100 pF

°

C

TA = 25

, OUTPUT VOLTAGE (2.0 mV/DIV)

O

V

SPICE Model

If a SPICE Macromodel is desired for the MC33206/07,
the user can define the characteristics from the following
information. Obtain the SPICE Macromodel for the MC33204
Rail–to–Rail Operational Amplifier (device is the same as the
MC33207). For the Enable feature of the MC33207, simulate
it as a bipolar switch. The Macromodel does not include an
input capacitance between the inverting and noninverting
inputs. This capacitor is called Cin. Add 3.0 to 5.0 pF if
stability analysis is required.

VCC = 6.0 V
VEE = –6.0 V

Ω

RL = 600
CL = 100 pF

°

C

TA = 25

, OUTPUT VOLTAGE (50 mV/DIV)V

O

10

t, TIME (5.0 µs/DIV)

, OUTPUT VOLTAGE (2.0 V/DIV)V

O

Figure 34. Large Signal Transient Response

VCC = 6.0 V
VEE = –6.0 V

Ω

RL = 600
CL = 100 pF
AV = 1.0

°

C

TA = 25

t, TIME (10 µs/DIV)

MOTOROLA ANALOG IC DEVICE DATA

t, TIME (10

µ

s/DIV)

MC33206 MC33207

OUTLINE DIMENSIONS

14 8

B

17

A

F

C

N

HG D

–A–

14 8

G

–T–

SEATING
PLANE

D 14 PL

0.25 (0.010) A

SEATING
PLANE

71

M

–B–

T

K

P 7 PL

C

K

S

B

P SUFFIX

PLASTIC PACKAGE

CASE 646–06

ISSUE L

L

J

M

D SUFFIX

PLASTIC PACKAGE

CASE 751A–03

(SO–14)

ISSUE F

0.25 (0.010) B

M

X 45

R

_

M

S

NOTES:

1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE
POSITION AT SEATING PLANE AT MAXIMUM
MATERIAL CONDITION.

2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.

3. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.

4. ROUNDED CORNERS OPTIONAL.

DIM MIN MAX MIN MAX

A 0.715 0.770 18.16 19.56
B 0.240 0.260 6.10 6.60
C 0.145 0.185 3.69 4.69
D 0.015 0.021 0.38 0.53

F 0.040 0.070 1.02 1.78
G 0.100 BSC 2.54 BSC
H 0.052 0.095 1.32 2.41

J 0.008 0.015 0.20 0.38
K 0.115 0.135 2.92 3.43

L 0.300 BSC 7.62 BSC
M 0 10 0 10

____

N 0.015 0.039 0.39 1.01

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

M

F

J

PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.

DIM MIN MAX MIN MAX

A 8.55 8.75 0.337 0.344
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
P 5.80 6.20 0.228 0.244
R 0.25 0.50 0.010 0.019

MILLIMETERSINCHES

INCHESMILLIMETERS

____

–A–

916

B

18

F

S

H

G

D

16 PL

K

0.25 (0.010) T

MOTOROLA ANALOG IC DEVICE DATA

P SUFFIX

PLASTIC PACKAGE

CASE 648–08

ISSUE R

C

SEATING

–T–

PLANE

J

M

M

A

L

M

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

DIM MIN MAX MIN MAX

A 0.740 0.770 18.80 19.55
B 0.250 0.270 6.35 6.85
C 0.145 0.175 3.69 4.44
D 0.015 0.021 0.39 0.53
F 0.040 0.70 1.02 1.77
G 0.100 BSC 2.54 BSC
H 0.050 BSC 1.27 BSC
J 0.008 0.015 0.21 0.38
K 0.110 0.130 2.80 3.30
L 0.295 0.305 7.50 7.74
M 0 10 0 10
S 0.020 0.040 0.51 1.01

MILLIMETERSINCHES

____

11

–T–

MC33206 MC33207

OUTLINE DIMENSIONS

D SUFFIX

PLASTIC PACKAGE

CASE 751B–05

(SO–16)

–A–

16 9

–B–

18

8 PLP

G

K

C

SEATING

PLANE

D

16 PL

0.25 (0.010) A

M

S

B

T

S

ISSUE J

0.25 (0.010) B

M

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

M

S

R

X 45

_

F

J

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.

DIM MIN MAX MIN MAX

A 9.80 10.00 0.386 0.393
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009

M 0 7 0 7

____

P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019

INCHESMILLIMETERS

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAP AN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF [e-mail] – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T ., Hong Kong. 852–26629298

12

◊

MOTOROLA ANALOG IC DEVICE DATA

MC33206/D

*MC33206/D*