Datasheet MC1776CDR2 Datasheet (MOTOROLA)

Device

Operating

Temperature Range

Package



SEMICONDUCTOR

TECHNICAL DATA

PROGRAMMABLE

OPERATIONAL AMPLIFIER

ORDERING INFORMATION

MC1776CD
MC1776CP1

TA = 0° to +70°C

SO–8

Plastic DIP

PIN CONNECTIONS

Order this document by MC1776C/D

P1 SUFFIX

PLASTIC PACKAGE

CASE 626

D SUFFIX

PLASTIC PACKAGE

CASE 751

(SO–8)

1

1

8

8

(Top View)

I

set

V

CC
Output
Offset Null

Offset Null

Invert

Noninvert

V

EE

1

2

3

4

8

7

6

5

+

–

Input

1

MOTOROLA ANALOG IC DEVICE DATA

 
 

This extremely versatile operational amplifier features low power
consumption and high input impedance. In addition, the quiescent currents
within the device may be programmed by the choice of an external resistor
value or current source applied to the I

set

input. This allows the amplifier’s
characteristics to be optimized for input current and power consumption
despite wide variations in operating power supply voltages.

• ±1.2 V to ±18 V Operation

• Wide Programming Range

• Of fset Null Capability

• No Frequency Compensation Required

• Low Input Bias Currents

• Short Circuit Protection

Resistive Programming

(See Figure 1)

R

set

to Ground R

set

to Negative Supply

Active Programming

FET Current Source Bipolar Current Source

(Recommended for supply voltage

less than ±6.0 V)

Typical R

set

Values

VCC, VEEI

set

= 1.5 µAI

set

= 15 µA

±6.0 V

±10 V
±12 V
±15 V

3.6 MΩ

6.2 MΩ

7.5 MΩ
10 MΩ

360 kΩ
620 kΩ
750 kΩ

1.0 MΩ

Pins not shown are not connected.

Typical R

set

Values

VCC, VEEI

set

= 1.5 µAI

set

= 15 µA

±1.5 V
±3.0 V
±6.0 V

±15 V

1.6 MΩ

3.6 MΩ

7.5 MΩ
20 MΩ

160 kΩ
360 kΩ
750 kΩ

2.0 MΩ

VCC – 0.6

R

set

I

set

=

7

2

3

4

8

–

+

R

set

V

EE

I

set

=

VCC – 0.6 – V

EE

R

set

–

+

2

3

7

6

4

8

V

EE

V

G

V

EE

7

2

3

4

8

6

V

EE

R

V

B

V

EE

Q

–

+

6

V

CC

V

CC

7

2

3

4

8

–

+

R

set

V

EE

6

V

CC

 Motorola, Inc. 1996 Rev 5

MC1776C

2

MOTOROLA ANALOG IC DEVICE DATA

MAXIMUM RATINGS (T

A

= +25°C, unless otherwise noted.)

Rating Symbol Value Unit

Power Supply Voltages V

CC,VEE

±18 Vdc

Differential Input Voltage V

ID

±30 Vdc

Common Mode Input Voltage V

ICM

Vdc

VCC and |VEE| t 15 V V

CC,VEE

VCC and |VEE| w 15 V ±15

Offset Null to VEE Voltage V

off–VEE

±0.5 Vdc

Programming Current I

set

500 µA

Programming Voltage V

set

(VCC –2.0 V) Vdc

(Voltage from I

set

T erminal to Ground) to V

CC

Output Short Circuit Duration (Note 1) t

SC

Indefinite sec

Operating Temperature Range T

A

0 to +70 °C

Storage Temperature Range T

stg

–65 to +150 °C

Junction Temperature T

J

150 °C

NOTE 1. May be to ground or either supply voltage. Rating applies up to a case temperature of +125°C

or ambient temperature of +70°C and I

set

≤ 30 µA.

2
3

4

6

7

V

CC

Output

V

EE

50

100

100

50

100

2.0 k

30 pF

10 k

Inputs

8

+

–

1
5

I

set

10 k

Offset Null

Representative Schematic Diagram

Voltage Offset Null Circuit Transient Response Test Circuit

2

3

7

V

CC

6

100 k

V

EE

1

4

8

R

set

–

+

+

–

2

3

7

8

4

6

V

CC

R

set

C

L

R

L

V

O

V

in

Pins not shown are
not connected.

V

EE

5

MC1776C

3

MOTOROLA ANALOG IC DEVICE DATA

ELECTRICAL CHARACTERISTICS (V

CC

= +3.0 V , VEE = –3.0 V, I

set

= 1.5 µA, TA = +25°C, unless otherwise noted.*)

Characteristic Symbol Min Typ Max Unit

Input Offset Voltage (RS ≤ 10 kΩ) V

IO

mV
TA = +25°C – 2.0 6.0
T

low

* ≤ TA ≤ T

high

* – – 7.5

Offset Voltage Adjustment Range V

IOR

– 9.0 – mV

Input Offset Current I

IO

nA
TA = +25°C – 0.7 6.0
TA = T

high

– – 6.0

TA = T

low

– – 10

Input Bias Current I

IB

nA
TA = +25°C – 2.0 10
TA = T

high

– – 10

TA = T

low

– – 20

Input Resistance r

i

– 50 – MΩ

Input Capacitance c

i

– 2.0 – pF

Input Voltage Range V

ID

V

T

low

≤ TA ≤ T

high

+1.0 – –

Large Signal Voltage Gain A

VOL

V/V
RL ≥ 75 kΩ, VO = ±1.0 V , TA = +25°C 25 k 200 k –
RL ≥ 75 kΩ, VO = ±1.0 V , T

low

≤ TA ≤ T

high

25 k – –

Output Voltage Swing V

O

V

RL ≥ 75 kΩ, T

low

≤ TA ≤ T

high

±2.0 ±2.4 –

Output Resistance r

o

– 5.0 – kΩ

Output Short Circuit Current I

SC

– 3.0 – mA

Common Mode Rejection CMR dB

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

70 86 –

Supply Voltage Rejection Ratio PSRR µV/V

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

– 25 200

Supply Current ICC, I

EE

µA
TA = +25°C – 13 20
T

low

≤ TA ≤ T

high

– – 25

Power Dissipation P

D

µW
TA = +25°C – 78 120
T

low

≤ TA ≤ T

high

– – 150

Transient Response (Unity Gain)

Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF

Rise Time t

TLH

– 3.0 – µs

Overshoot os – 0 – %

Slew Rate (RL ≥ 5.0 kΩ) S

R

– 0.03 – V/µs

*T

low

= 0°CT

high

= +70°C

MC1776C

4

MOTOROLA ANALOG IC DEVICE DATA

ELECTRICAL CHARACTERISTICS (V

CC

= +3.0 V , VEE = –3.0 V, I

set

= 15 µA, TA = +25°C, unless otherwise noted.*)

Characteristic Symbol Min Typ Max Unit

Input Offset Voltage (RS ≤ 10 kΩ) V

IO

mV
TA = +25°C – 2.0 6.0
T

low

* ≤ TA ≤ T

high

* – – 7.5

Offset Voltage Adjustment Range V

IOR

– 18 – mV

Input Offset Current I

IO

nA
TA = +25°C – 2.0 25
TA = T

high

– – 25

TA = T

low

– – 40

Input Bias Current I

IB

nA
TA = +25°C – 15 50
TA = T

high

– – 50

TA = T

low

– – 100

Input Resistance r

i

– 5.0 – MΩ

Input Capacitance c

i

– 2.0 – pF

Input Voltage Range V

ID

V

T

low

≤ TA ≤ T

high

±1.0 – –

Large Signal Voltage Gain A

VOL

V/V
RL ≥ 5.0 kΩ, VO = ±1.0 V , TA = +25°C 25 k 200 k –
RL ≥ 5.0 kΩ, VO = ±1.0 V , T

low

≤ TA ≤ T

high

25 k – –

Output Voltage Swing V

O

V

RL ≥ 5.0 kΩ, T

low

≤ TA ≤ T

high

±2.0 ±2.1 –

Output Resistance r

o

– 1.0 – kΩ

Output Short Circuit Current I

SC

– 5.0 – mA

Common Mode Rejection CMR dB

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

70 86 –

Supply Voltage Rejection Ratio PSRR µV/V

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

– 25 200

Supply Current ICC, I

EE

µA
TA = +25°C – 130 170
T

low

≤ TA ≤ T

high

– – 180

Power Dissipation P

D

µW
TA = +25°C – 780 1020
T

low

≤ TA ≤ T

high

– – 1080

Transient Response (Unity Gain)

Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF

Rise Time t

TLH

– 0.6 – µs

Overshoot os – 5.0 – %

Slew Rate (RL ≥ 5.0 kΩ) S

R

– 0.35 – V/µs

*T

low

= 0°CT

high

= +70°C

MC1776C

5

MOTOROLA ANALOG IC DEVICE DATA

ELECTRICAL CHARACTERISTICS (V

CC

= +15 V , VEE = –15 V, I

set

= 1.5 µA, TA = +25°C, unless otherwise noted.*)

Characteristic Symbol Min Typ Max Unit

Input Offset Voltage (RS ≤ 10 kΩ) V

IO

mV
TA = +25°C – 2.0 6.0
T

low

* ≤ TA ≤ T

high

* – – 7.5

Offset Voltage Adjustment Range V

IOR

– 9.0 – mV

Input Offset Current I

IO

nA
TA = +25°C – 0.7 6.0
TA = T

high

– – 6.0

TA = T

low

– – 10

Input Bias Current I

IB

nA
TA = +25°C – 2.0 10
TA = T

high

– – 10

TA = T

low

– – 20

Input Resistance r

i

– 50 – MΩ

Input Capacitance c

i

– 2.0 – pF

Input Voltage Range V

ID

V

T

low

≤ TA ≤ T

high

±10 – –

Large Signal Voltage Gain A

VOL

V/V
RL ≥ 75 kΩ, VO = ±10 V , TA = +25°C 50 k 400 k –
RL ≥ 75 kΩ, VO = ±10 V , T

low

≤ TA ≤ T

high

50 k – –

Output Voltage Swing V

O

V
RL ≥ 75 kΩ, TA = +25°C ±12 ±14 –
RL ≥ 75 kΩ, T

low

≤ TA ≤ T

high

±10 – –

Output Resistance r

o

– 5.0 – kΩ

Output Short Circuit Current I

SC

– 3.0 – mA

Common Mode Rejection CMR dB

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

70 90 –

Supply Voltage Rejection Ratio PSRR µV/V

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

– 25 200

Supply Current ICC, I

EE

µA
TA = +25°C – 20 30
T

low

≤ TA ≤ T

high

– – 35

Power Dissipation P

D

mW
TA = +25°C – 780 0.9
T

low

≤ TA ≤ T

high

– – 1.05

Transient Response (Unity Gain)

Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF

Rise Time t

TLH

– 1.6 – µs

Overshoot os – 0 – %

Slew Rate (RL ≥ 5.0 kΩ) S

R

– 0.1 – V/µs

*T

low

= 0°CT

high

= +70°C

MC1776C

6

MOTOROLA ANALOG IC DEVICE DATA

ELECTRICAL CHARACTERISTICS (V

CC

= +15 V , VEE = –15 V, I

set

= 15 µA, TA = +25°C, unless otherwise noted.*)

Characteristic Symbol Min Typ Max Unit

Input Offset Voltage (RS ≤ 10 kΩ) V

IO

mV
TA = +25°C – 2.0 6.0
T

low

* ≤ TA ≤ T

high

* – – 7.5

Offset Voltage Adjustment Range V

IOR

– 18 – mV

Input Offset Current I

IO

nA
TA = +25°C – 2.0 25
TA = T

high

– – 25

TA = T

low

– – 40

Input Bias Current I

IB

nA
TA = +25°C – 15 50
TA = T

high

– – 50

TA = T

low

– – 100

Input Resistance r

i

– 5.0 – MΩ

Input Capacitance c

i

– 2.0 – pF

Input Voltage Range V

ID

V

T

low

≤ TA ≤ T

high

±10 – –

Large Signal Voltage Gain A

VOL

V/V
RL ≥ 5.0 kΩ, VO = ±10 V , TA = +25°C 50 k 400 k –
RL ≥ 75 kΩ, VO = ±10 V , T

low

≤ TA ≤ T

high

50 k – –

Output Voltage Swing V

O

V
RL ≥ 5.0 kΩ, TA = +25°C ±10 ±13 –
RL ≥ 75 kΩ, T

low

≤ TA ≤ T

high

±10 – –

Output Resistance r

o

– 1.0 – kΩ

Output Short Circuit Current I

SC

– 12 – mA

Common Mode Rejection CMR dB

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

70 90 –

Supply Voltage Rejection Ratio PSRR µV/V

RS ≤ 10 kΩ, T

low

≤ TA ≤ T

high

– 25 200

Supply Current ICC, I

EE

µA
TA = +25°C – 160 190
T

low

≤ TA ≤ T

high

– – 200

Power Dissipation P

D

µW
TA = +25°C – – 5.7
T

low

≤ TA ≤ T

high

– – 6.0

Transient Response (Unity Gain)

Vin = 20 mV, RL ≥ 5.0 kΩ, CL = 100 pF

Rise Time t

TLH

– 0.35 – µs

Overshoot os – 10 – %

Slew Rate (RL ≥ 5.0 kΩ) S

R

– 0.8 – V/µs

*T

low

= 0°CT

high

= +70°C

MC1776C

7

MOTOROLA ANALOG IC DEVICE DATA

Figure 1. Set Current versus Set Resistor

Figure 2. Positive Standby Supply Current

versus Set Current

Figure 3. Open Loop Gain versus Set Current Figure 4. Input Bias Current versus Set Current

Figure 5. Input Bias Current

versus Ambient Temperature

Figure 6. Gain Bandwidth Product

versus Set Current

I

set

, SET CURRENT (µA)

10 k

100 k

1.0 M

10 M

100 M

0.1 1.0 10 100

, SET RESISTOR (R

set

I

set

, SET CURRENT (µA)

0.01 0.1 1.0 10 100

0.1

1.0

10

100

1000

POSITIVE STANDBY SUPPLY CURRENT

µ

( A)

, OPEN LOOP GAIN (V/M)

I

set

, SET CURRENT (µA)

0.1 1.0 10 100

10

4

10

5

10

6

10

7

A

VOL

I

set

, SET CURRENT (µA)

0.01 0.1 1.0 10 100

0.1

1.0

10

100

, INPUT BIAS CURRENT (nA)I

IB

T, TEMPERATURE (°C)

0

6.0

12

18

24

30

–60 –40 –20 0 20 40 60 80 100 120 140

, INPUT BIAS CURRENT (nA)I

IB

I

set

= 1.5 µA

I

set

= 1.5 µA

GBW, GAIN BANDWIDTH PRODUCT (Hz)

I

set

, SET CURRENT (µA)

1.0 k

10 k

100 k

1.0 M

10 M

0.1 1.0 10 100

Ω

)

VCC = +15 V
VEE = –15 V
R

set

to V

EE

VCC = +15 V
VEE = –15 V
R

set

to GND

VCC = +3.0 V
VEE = –3.0 V
R

set

to GND

VCC = +3.0 V
VEE = –3.0 V
R

set

to V

EE

+3.0 V ≤ VCC ≤ +18 V
–3.0 V

≥

VEE ≥ –18 V

RL = 75 k

VCC = +15 V
VEE = –15 V

VCC = +3.0 V
VEE = –3.0 V

+3.0 V ≤ VCC ≤ +18 V
–3.0 V

≥

VEE ≥ –18 V

+3.0 V ≤ VCC ≤ +18 V
–3.0 V

≥

VEE ≥ –18 V

VCC = +15 V
VEE = –15 V

VCC = +3.0 V
VEE = –3.0 V

MC1776C

8

MOTOROLA ANALOG IC DEVICE DATA

Figure 7. Output Voltage Swing

versus Load Resistance

Figure 8. Supply Current

versus Ambient Temperature

Figure 9. Output Voltage Swing

versus Supply Voltage

Figure 10. Slew Rate

versus Set Current

Figure 11. Input Noise Voltage

versus Set Current

Figure 12. Optimum Source Resistance for

Minimum Noise versus Set Current

1.0 k 10 k 100 k 1.0 M

0

6.0

12

18

24

30

V

VOLTAGE SWING (V)

RL, LOAD RESISTANCE (Ω)

, PEAK–TO–PEAK OUTPUT

O(pp)

–60 –40 –20 0 20 40 60 80 100 120 140

0

30

60

90

120

150

T, AMBIENT TEMPERATURE (

°

C)

S

, SUPPLY CURRENT

µ

( A)I

0 2.0 4.0 6.0 8.0 10 12 14 16 18 20

0

4.0

8.0

12

16

20

24

28

32

36

40

VCC, (VEE), SUPPLY VOLTAGES (V)

V

O

,OUTPUT VOLTAGE SWING (V)

0.01 0.1 1.0 10 100

0.001

0.01

0.1

1.0

10

(V s)

µ

I

set

, SET CURRENT (µA)

SR, SLEW RATE

0.01 0.1 1.0 10 100

10

–17

10

–16

10

–15

10

–13

10

–14

I

set

, SET CURRENT (

µ

A)

V(RMS), MEAN SQUARE VOLTAGE(V /Hz)

2

0.01 0.1 1.0 10 100

0.1

1.0

10

100

OPTIMUM SOURCE RESISTANCE (M )

Ω

I

set

, SET CURRENT (µA)

VCC = +15 V
VEE = –15 V
I

set

= 15

µ

A

VCC = +15 V
VEE = –15 V
I

set

= 1.5

µ

A

VCC = +3.0 V
VEE = –3.0 V

1.5

µA ≤

I

set

≤ 15 µA

I

set

= 1.5 µA
VCC = +15 V
VEE = –15 V

I

set

= 15 µA
VCC = +3.0 V
VEE = –3.0 V

I

set

= 1.5 µA
VCC = +3.0 V
VEE = –3.0 V

I

set

= 1.5 µA
VCC = +15 V
VEE = –15 V

1.5 µA ≤ I

set

≤ 15 mA

RL = 75 k

I

set

= 15 µA

RL = 5.0 k

I

set

= 1.5 µA

RL = 5.0 k

VCC = +15 V
VEE = –15 V

VCC = +3.0 V
VEE = –3.0 V

f = 1.0 kHz

∆

1 = Hz

+3.0 V

≤

VCC ≤ +18 V

–3.0 V

≥

VEE ≥ –18 V

MC1776C

9

MOTOROLA ANALOG IC DEVICE DATA

Figure 13. Wien Bridge Oscillator

Figure 14. Multiple Feedback Bandpass Filter

Figure 15. Multiple Feedback Bandpass Filter

(1.0 kHz)

Figure 16. Gated Amplifier

Figure 17. High Input Impedance Amplifier

MC1776C

22 k

200 k

2

3

C

R

V

O

10 k

R

set

7

6

8

4

–15 V

R

C

–

+

+15 V

fo =

1

2

π

RC

(for fo = 1.0 kHz)

R= 16 k

Ω

C = 0.01 µF

Choose a value for C, then

R5 =

R1 =

R2 =

MC1776C

C

C

2

3

–

+

7

6

V

O

R

set

4

R

5

R

2

V

EE

R

1

V

in

V

CC

Q

R5

2A (fo)

R1,R5

QO f

o

GBW

≤

0.1

8

MC1776C

+15 V

Input

Output

–15 V

2.0 M

8

4

C

R

2

R

1

R

5

2

3

6

7

–

+

for a 1.0 kHz filter
with Q = 10
and A (fo) = 1

R1 = 160 k
R2 = 820
R5 = 300 k
C = 0.01

µ

F

MC1776C

Input

Output

–

+

2

3

–15 V

8

4

6

V

CC

15 V

2.7 M

270 k

7

10 k

1 M

Q

Gate

+15 V

10 k

10 k

5.6 k

MC1776C

50 M

10 k

90 k

OutputInput

500 k

500 k

50 M

–

+

2

3

6

7

4

8

+15 V

30 M

–15 V

C

For a given:

fo = center frequency
A (fo) = Gain at center frequency
Q = quality factor

To obtain less than 10% error from the operational amplifier:

where fo and GBW are expressed in Hz. GBW is available from
Figure 6 as a function of Set Current, I

set

.

π

foC

4Q2 R1–R5

MC1776C

10

MOTOROLA ANALOG IC DEVICE DATA

P1 SUFFIX

PLASTIC PACKAGE

CASE 626–05

ISSUE K

D SUFFIX

PLASTIC PACKAGE

CASE 751–05

(SO–8)

ISSUE R

OUTLINE DIMENSIONS

NOTES:

1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.

2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).

3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

14

58

F

NOTE 2

–A–

–B–

–T–

SEATING
PLANE

H

J

G

D

K

N

C

L

M

M

A

M

0.13 (0.005) B

M

T

DIM MIN MAX MIN MAX

INCHESMILLIMETERS

A 9.40 10.16 0.370 0.400
B 6.10 6.60 0.240 0.260
C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020

F 1.02 1.78 0.040 0.070
G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050

J 0.20 0.30 0.008 0.012
K 2.92 3.43 0.1 15 0.135

L 7.62 BSC 0.300 BSC
M ––– 10 ––– 10
N 0.76 1.01 0.030 0.040

__

SEATING
PLANE

1

4

58

A0.25MCB

SS

0.25MB

M

h

q

C

X 45

_

L

DIM MIN MAX

MILLIMETERS

A 1.35 1.75

A1 0.10 0.25

B 0.35 0.49
C 0.18 0.25
D 4.80 5.00
E

1.27 BSCe

3.80 4.00

H 5.80 6.20
h

0 7

L 0.40 1.25

q

0.25 0.50

__

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.

2. DIMENSIONS ARE IN MILLIMETERS.

3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.

D

E

H

A

B

e

B

A1

C

A

0.10

MC1776C

11

MOTOROLA ANALOG IC DEVICE DATA

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

MC1776C

12

MOTOROLA ANALOG IC DEVICE DATA

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Ta tsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF [e-mail] – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Ko k Road, Tai Po, N.T ., Hong Kong. 852–26629298

MC1776C/D

*MC1776C/D*

◊