Page 1
SEMICONDUCTOR TECHNICAL DATA
2–316
REV 2
Motorola, Inc. 1996
9/96
The MC10H/100H607 is a 6–bit, registered PECL to TTL translator.
The device features differential PECL inputs for both data and clock. The
TTL outputs feature 48mA sink, 24mA source drive capability for driving
high fanout loads or transmission lines. The asynchronous master reset
control is an ECL level input.
With its differential PECL inputs and TTL outputs the H607 device is
ideally suited for the receive function of a HPPI bus type board–to–board
interface application. The on chip registers simplify the task of
synchronizing the data between the two boards.
The device is available in either ECL standard: the 10H device is
compatible with MECL 10H logic levels, with a VCC of +5.0 volts, while
the 100H device is compatible with 100K logic levels, with a VCC of +5.0
volts.
• Differential ECL Data and Clock Inputs
• 48mA Sink, 15mA Source TTL Outputs
• Single Power Supply
• Multiple Power and Ground Pins to Minimize Noise
Pinout: 28–Lead PLCC (Top View)
1
EGND
Q3V
CCTQ4
TGND Q5V
CCT
MR
D
5
D
5
D
4
D
4
V
CCE
D
3
D
3
D
2
D
2
D
1
D
1
D
0
D
0
V
BB
CLK
CLK
TGND
Q
0
Q
1
Q
2
4
3
2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11109
7
8
6
5
MECL 10H is a trademark of Motorola, Inc.
FN SUFFIX
PLASTIC PACKAGE
CASE 776–02
Page 2
MC10H607 MC100H607
2–317 MOTOROLAMECL Data
DL122 — Rev 6
D
n
D
n
LOGIC DIAGRAM
Q
n
MR
CLK
CLK
V
BB
1 OF 6 BITS
D
CLK
R
Q
PIN NAMES
Pin Function
D0 – D
5
D
0
– D
5
CLK, CLK
MR
Q0 – Q
5
True PECL Data Inputs
Inverted PECL Data Inputs
Differential PECL Clock Input
PECL Master Reset Input
TTL Outputs
V
CCE
V
CCT
TGND
EGND
PECL V
CC
TTL V
CC
TTL Ground
PECL Ground
TRUTH TABLE
D
n
MR TCLK/CLK Qn + 1
L
H
X
L
L
H
Z
Z
X
L
H
L
Z = LOW to HIGH Transition
DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = + 25°C TA = + 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit Condition
I
EE
ECL Power Supply Current
10H
100H
70
65
85
80
70
70
85
85
70
75
85
95
mA
I
CCL
TTL Supply Current 100 120 100 120 100 120 mA
I
CCH
TTL Supply Current 100 120 100 120 100 120 mA
Page 3
MC10H607 MC100H607
MOTOROLA MECL Data
DL122 — Rev 6
2–318
10H PECL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
I
INH
Input HIGH Current 255 145 145 µ
A
I
INL
Input LOW Current 0.5 0.5 0.5 µ
A
V
IH
Input HIGH Voltage 3830 4160 3870 4190 3930 4280 mV V
CCT
= 5.0V
V
IL
Input LOW Voltage 3050 3520 3050 3520 3050 3555 mV V
CCT
= 5.0V
V
BB
Output Bias Voltage 3600 3710 3630 3730 3670 3790 mV V
CCT
= 5.0V
NOTE: PECL VIL, VIH, VOL, VOH, VBB are given for V
CCT
= V
CCE
= 5.0V and will vary 1:1 with power supply.
100H PECL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
I
IH
Input HIGH Current 255 145 145 µ
A
I
IL
Input LOW Current 0.5 0.5 0.5 µ
A
V
IH
Input HIGH Voltage 3835 4120 3835 4120 3835 4120 mV V
CCT
= 5.0V
V
IL
Input LOW Voltage 3190 3525 3190 3525 3190 3525 mV V
CCT
= 5.0V
V
BB
Output Bias Voltage 3600 3720 3600 3720 3600 3720 mV V
CCT
= 5.0V
NOTE: PECL VIL, VIH, VOL, VOH, VBB are given for V
CCT
= V
CCE
= 5.0V and will vary 1:1 with power supply.
10H/100H TTL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
V
OH
Output HIGH Voltage 2.5
2.0
2.5
2.0
2.5
2.0
V IOH = –15mA
IOH = –24mA
V
OL
Output LOW Voltage 0.55 0.55 0.55 V IOL = 48mA
NOTE: DC levels such as VOH, VOL, etc., are standard for PECL and FAST devices, with the exceptions of: IOL = 48mA at 0.5VOL;
and IOH = 24mA at 2.0VOH.
AC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = + 25°C TA = + 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
t
PLH++
t
PHH+–
Propagation Delay to Output CLK to Q 5.5
4.6
7.7.
7.7
6.0
4.9
8.2
8.3
6.7
5.9
10.0
10.0
ns CL = 50pF
t
PHL+–
Propagation Delay to Output MR to Q 4.4 7.5 4.7 8.1 5.8 10.5 ns CL = 50pF
t
PW
Minimum Pulse Width CLK, MR 1.0 1.0 1.0 ns
t
r
Rise Time 0.5 2.0 0.5 2.0 0.5 2.0 ns 0.8 – 2.0V
t
f
Fall Time 0.5 2.0 0.5 2.0 0.5 2.0 ns 0.8 – 2.0V
t
S
Setup Time 1.5 1.5 1.5 ns
t
H
Hold Time 1.5 1.5 1.5 ns
V
PP
Minimum Input Swing 200 200 200 mV
1. Numbers are for both ++ and – – delay MR to Q.
Page 4
MC10H607 MC100H607
2–319 MOTOROLAMECL Data
DL122 — Rev 6
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776–02
ISSUE D
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
–N–
–M–
–L–
V
W
D
D
Y BRK
28 1
VIEW S
S
L–M
S
0.010 (0.250) N
S
T
S
L–M
M
0.007 (0.180) N
S
T
0.004 (0.100)
G1
G
J
C
Z
R
E
A
SEATING
PLANE
S
L–M
M
0.007 (0.180) N
S
T
–T–
B
S
L–M
S
0.010 (0.250) N
S
T
S
L–M
M
0.007 (0.180) N
S
T
U
S
L–M
M
0.007 (0.180) N
S
T
Z
G1X
VIEW D–D
S
L–M
M
0.007 (0.180) N
S
T
K1
VIEW S
H
K
F
S
L–M
M
0.007 (0.180) N
S
T
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A 0.485 0.495 12.32 12.57
B 0.485 0.495 12.32 12.57
C 0.165 0.180 4.20 4.57
E 0.090 0.110 2.29 2.79
F 0.013 0.019 0.33 0.48
G 0.050 BSC 1.27 BSC
H 0.026 0.032 0.66 0.81
J 0.020 ––– 0.51 –––
K 0.025 ––– 0.64 –––
R 0.450 0.456 11.43 11.58
U 0.450 0.456 11.43 11.58
V 0.042 0.048 1.07 1.21
W 0.042 0.048 1.07 1.21
X 0.042 0.056 1.07 1.42
Y ––– 0.020 ––– 0.50
Z 2 10 2 10
G1 0.410 0.430 10.42 10.92
K1 0.040 ––– 1.02 –––
____
Page 5
MC10H607 MC100H607
MOTOROLA MECL Data
DL122 — Rev 6
2–320
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMF AX0@email.sps.mot.com – T OUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC10H607/D
*MC10H607/D*
◊
Loading...