Datasheet MC10H600FNR2, MC10H600FN, MC100H600FN, MC100H600FNR2 Datasheet (Motorola)

Page 1



SEMICONDUCTOR TECHNICAL DATA

  

The MC10H/100H600 is a 9–bit, dual supply TTL to ECL translator. Devices in the Motorola 9–bit translator series utilize the 28–lead PLCC for optimal power pinning, signal flow–through and electrical performance.

The H600 features both ECL and TTL logic enable controls for maximum flexibility .

The 10H version is compatible with MECL 10H ECL logic levels. The 100H version is compatible with 100K levels.

• 9–Bit Ideal for Byte–Parity Applications

• Flow–Through Configuration

• Extra TTL and ECL Power/Ground Pins to Minimize Switching Noise

• ECL and TTL Enable Inputs

• Dual Supply

• 3.5 ns Max D to Q

• PNP TTL Inputs for Low Loading

• Choice of ECL Compatibility: MECL 10H (10Hxxx) or 100K (100Hxxx)

LOGIC SYMBOL

ENECL

ENTTL





FN SUFFIX

PLASTIC PACKAGE

CASE 776–02

PIN NAMES

PIN FUNCTION

GND V

CCE

CCO

CCT

D0–D8 Q0–Q8 ENECL ENTTL

TTL Ground (0 V) ECL VCC (0 V) ECL VCC (0 V) — Outputs TTL Supply (+5.0 V) ECL Supply (–5.2/–4.5 V) Data Inputs (TTL) Data Outputs (ECL) Enable Control (ECL) Enable Control (TTL)

TTL ECL

TRUTH TABLE

ENECL

H H X X

ENTTL

X X H H L

Pinout: 28–Lead PLCC (Top View)

D6 D7 D8

GND

ENTTL

ENECL

D5 D4 V

25 24 23 22 21 20 19

5678 91011

Q8 Q7 V

D3 D2 D1 D0

CCT

Q6 VEEQ5 Q4

CCO

L L

CCE

CCO

3/93

 Motorola, Inc. 1996

2–140

REV 5

Page 2

MC10H600 MC100H600

DC CHARACTERISTICS: V

Symbol Parameter

Power Supply Current

CCH

CCL

ECL 10H

TTL 48

AC CHARACTERISTICS: V

Symbol Parameter

PLH

PHL

Propagation Delay to Output

Output Rise/Fall Time

20%–80%

= 5.0 V ± 10%; VEE = –5.2 V ± 5% (10H version); VEE = –4.2 V to –5.5 V (100H version)

CCT

= 5.0 V ± 10%; VEE = –5.2 V ± 5% (10H version); VEE = –4.2 V to –5.5 V (100H version)

CCT

10H ECL DC CHARACTERISTICS: V

Symbol Parameter

Input HIGH Current Input LOW Current 0.5

Input HIGH Voltage Input LOW Voltage

Output HIGH Voltage Output LOW Voltage

100H ECL DC CHARACTERISTICS: V

Symbol Parameter

TTL DC CHARACTERISTICS: V

Symbol Parameter

Input HIGH Current Input LOW Current 0.5

Input HIGH Voltage Input LOW Voltage

Output HIGH Voltage Output LOW Voltage

= 5.0 V ± 10%; VEE = –5.2 V ± 5% (10H version); VEE = –4.2 V to –5.5 V (100H version)

CCT

Input HIGH Voltage Input LOW Voltage

Input HIGH Current 20

Input LOW Current –0.6 –0.6 –0.6 mA VIN = 0.5 V Input Clamp Voltage –1.2 –1.2 –1.2 V IIN = –18 mA

0°C 25°C 75°C

Min Max Min Max Min Max

100H

Min Max Min Max Min Max

D 1.4 3.0 1.5 3.2 1.7 3.5 ns 50 Ω to –2.0 V

ENECL/

ENTTL

= 5.0 V ± 10%; VEE = –5.2 V ± 5%

CCT

Min Max Min Max Min Max

–1170 –1950

–1020 –1950

= 5.0 V ± 10%; VEE = –4.2 V to –5.5 V

CCT

Min Max Min Max Min Max

–1165 –1810

–1025 –1810

Min Max Min Max Min Max

–125 –122

0°C 25°C 75°C

1.8 3.7 1.9 3.9 2.0 4.1 ns 50 Ω to –2.0 V

0.5 1.5 0.5 1.5 0.5 1.5 ns 50 Ω to –2.0 V

0°C 25°C 75°C

225

–840

–1480

–840

–1630

0°C 25°C 75°C

–880

–1475

–880

–1620

0°C 25°C 75°C

2.0

–1130 –1950

–980

–1950

225

–1165 –1810

–1025 –1810

0.8

100

0.5

2.0

–125 –123

48 50

145

–810

–1480

–810

–1630

145

–880

–1475

–880

–1620

0.8 20

100

0.5

–1070 –1950

–920

–1950

0.5

–1165

–1810 –1025

–1810

2.0

–125 –132

145 µA

–735

–1450

–735

–1600

145 µA

–880

–1475

–880

–1620

0.8

100

Unit Condition

48 50

Unit Condition

µA

mV 50 Ω to –2.0 V

Unit Condition

µA

mV 50 Ω to –2.0 V

Unit Condition

V V

µA VIN = 2.7 V

VIN = 7.0 V

DL122 — Rev 6

2–141 MOTOROLAMECL Data

Page 3

MC10H600 MC100H600

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 776–02

ISSUE D

–L–

–N–

28 1

0.010 (0.250) N

L–M

Y BRK

0.007 (0.180) N

L–M

–M–

0.010 (0.250) N

G1X

L–M

VIEW D–D

0.007 (0.180) N

L–M

0.007 (0.180) N

L–M

0.004 (0.100)

SEATING

–T–

PLANE

VIEW S

0.007 (0.180) N

L–M

NOTES:

1. DATUMS –L–, –M–, AND –N– DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE.

2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DA TUM –T–, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS

0.010 (0.250) PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).

DIM MIN MAX MIN MAX

A 0.485 0.495 12.32 12.57 B 0.485 0.495 12.32 12.57 C 0.165 0.180 4.20 4.57

E 0.090 0.110 2.29 2.79

F 0.013 0.019 0.33 0.48 G 0.050 BSC 1.27 BSC H 0.026 0.032 0.66 0.81

J 0.020 ––– 0.51 ––– K 0.025 ––– 0.64 ––– R 0.450 0.456 11.43 11.58 U 0.450 0.456 11.43 11.58

V 0.042 0.048 1.07 1.21 W 0.042 0.048 1.07 1.21

X 0.042 0.056 1.07 1.42

Y ––– 0.020 ––– 0.50

Z 2 10 2 10

____

G1 0.410 0.430 10.42 10.92 K1 0.040 ––– 1.02 –––

MILLIMETERSINCHES

MOTOROLA MECL Data

2–142

DL122 — Rev 6

Page 4

MC10H600 MC100H600

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

How to reach us: USA/EUROPE /Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF AX0@email.sps.mot.com – T OUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, INTERNET: http://Design–NET .com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

ÀMC10H600/D

DL122 — Rev 6

◊

2–143 MOTOROLAMECL Data

*ÀMC10H600/D*