Datasheet MC10H332FN, MC10H332FNR2 Datasheet (MOTOROLA)



SEMICONDUCTOR TECHNICAL DATA

2–13

REV 5

 Motorola, Inc. 1996

3/93

   
  !

The MC10H332 is a Dual Bus Driver/Receiver with four–to–one output
multiplexers. These multiplexers have common selects and output enable.
When disabled, (OE

= high) the bus outputs go to –2.0 V. The parameters
specified are with 25 Ω loading on the bus drivers and 50 Ω loads on the
receivers.

• Propagation Delay, 1.5 ns Typical Data–to–Output

• Improved Noise Margin 150 mV (Over Operating Voltage and

Temperature Range)

• Voltage Compensated

• MECL 10K–Compatible

MAXIMUM RATINGS

Characteristic Symbol Rating Unit

Power Supply (VCC = 0) V

EE

–8.0 to 0 Vdc

Input Voltage (VCC = 0) V

I

0 to V

EE

Vdc

Output Current— Continuous

— Surge

I

out

50

100

mA

Operating Temperature Range T

A

0 to +75 °C

Storage Temperature Range— Plastic

— Ceramic

T

stg

–55 to +150
–55 to +165

°C
°C

ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)

0° 25° 75°

Characteristic Symbol Min Max Min Max Min Max Unit

Power Supply Current I

E

— 115 — 110 — 115 mA

Input Current High

Pins 3,4,5,6,14,

15,16,17
Pins 7,8
Pins 13, 18

I

inH

—
—
—

667
437
456

—
—
—

417
273
285

—
—
—

417
273
285

µA

Input Current Low I

inL

0.5 — 0.5 — 0.3 — µA

High Output Voltage V

OH

–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc

Low Output Voltage V

OL

–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc

High Input Voltage V

IH

–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc

Low Input Voltage V

IL

–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc

AC PARAMETERS

Propagation Delay

Data–to–Bus Output
Select–to–Bus

Output
OE

–to–Bus Output
Bus–to–Receiver
Select–to–Receiver
RE

–to–Receiver
Data–to–Receiver

t

pd

0.8

0.8

0.8

0.8

1.8

0.8

1.3

3.0

3.4

2.4

2.1

4.5

2.2

4.0

0.8

0.8

0.8

0.8

1.8

0.8

1.3

3.0

3.4

2.4

2.1

4.5

2.2

4.0

0.8

0.8

0.8

0.8

1.8

0.8

1.3

3.2

3.8

2.6

2.4

5.0

2.5

4.5

ns

Rise Time t

r

0.5 2.0 0.5 2.0 0.5 2.1 ns

Fall Time t

f

0.5 2.0 0.5 2.0 0.5 2.1 ns



DIP & PLCC

PIN ASSIGNMENT

V

CC

X

BUS

X0
X1
X2
X3
S0
S1

V

CC02

Y

BUS

OE
Y0
Y1
Y2
Y3
RE

20
19
18
17
16
15
14

13

1
2
3
4
5
6
7
8

X

IN

V

EE

Y

IN

V

CC01

12
11

9
10

NOTE:

Each MECL 10H series circuit has been designed
to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.

L SUFFIX

CERAMIC PACKAGE

CASE 732–03

P SUFFIX

PLASTIC PACKAGE

CASE 738–03

FN SUFFIX

PLCC

CASE 775–02

Pin assignment is for Dual–in–Line Package.

For PLCC pin assignment, see the Pin Conversion

T ables on page 6–11 of the Motorola MECL Data

Book (DL122/D).

MC10H332

MOTOROLA MECL Data

DL122 — Rev 6

2–14

MULTIPLEXER TRUTH TABLE RECEIVER TRUTH

TABLE

V

CC

= PIN 1

V

CC01

= PIN 11

V

CC02

= PIN 20

V

EE

= PIN 10

OE S1 S0 X

Bus

Y

Bus

RE

X

in

Y

in

H
L
L
L
L

X
L
L
H
H

X
L

H

L

H

–2.0V

X0
X1
X2
X3

–2.0V

Y0
Y1
Y2
Y3

HLL

X

Bus

L

Y

Bus

OE

X0

X1

X2

X3

S0
S1

Y0

Y1

Y2

Y3

X

IN

RE

Y

IN

X

BUS

Y

BUS

7

6

5

16

15

8

9

13

4

3

2

19

18

17

14

12

LOGIC DIAGRAM

MC10H332

2–15 MOTOROLAMECL Data

DL122 — Rev 6

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 775–02

ISSUE C

NOTES:

1. DATUMS –L–, –M–, AND –N– DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.

2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).

–M–

–N–

–L–

Y BRK

W

V

D

D

S

L–M

M

0.007 (0.180) N

S

T

S

L–M

M

0.007 (0.180) N

S

T

S

L–M

S

0.010 (0.250) N

S

T

X

G1

B

U

Z

VIEW D–D

20 1

S

L–M

M

0.007 (0.180) N

S

T

S

L–M

M

0.007 (0.180) N

S

T

S

L–M

S

0.010 (0.250) N

S

T

C

G

VIEW S

E

J

R

Z

A

0.004 (0.100)

–T–

SEATING
PLANE

S

L–M

M

0.007 (0.180) N

S

T

S

L–M

M

0.007 (0.180) N

S

T

H

VIEW S

K

K1

F

G1

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A 0.385 0.395 9.78 10.03
B 0.385 0.395 9.78 10.03
C 0.165 0.180 4.20 4.57
E 0.090 0.110 2.29 2.79
F 0.013 0.019 0.33 0.48
G 0.050 BSC 1.27 BSC
H 0.026 0.032 0.66 0.81
J 0.020 ––– 0.51 –––
K 0.025 ––– 0.64 –––
R 0.350 0.356 8.89 9.04
U 0.350 0.356 8.89 9.04
V 0.042 0.048 1.07 1.21

W 0.042 0.048 1.07 1.21

X 0.042 0.056 1.07 1.42
Y ––– 0.020 ––– 0.50

Z 2 10 2 10
G1 0.310 0.330 7.88 8.38
K1 0.040 ––– 1.02 –––

____

MC10H332

MOTOROLA MECL Data

DL122 — Rev 6

2–16

OUTLINE DIMENSIONS

P SUFFIX

PLASTIC DIP PACKAGE

CASE 738–03

ISSUE E

L SUFFIX

CERAMIC DIP PACKAGE

CASE 732–03

ISSUE E

NOTES:

1. LEADS WITHIN 0.010 DIAMETER, TRUE
POSITION AT SEATING PLANE, AT MAXIMUM
MATERIAL CONDITION.

2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.

3. DIMENSIONS A AND B INCLUDE MENISCUS.

DIM MIN MAX

INCHES

A 0.940 0.990
B 0.260 0.295
C 0.150 0.200
D 0.015 0.022

F 0.055 0.065
G 0.100 BSC
H 0.020 0.050
J 0.008 0.012
K 0.125 0.160
L 0.300 BSC
M 0 15
N 0.010 0.040

__

A

20

110

11

B

F

C

SEATING
PLANE

D

H

G

K

N

J

M

L

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.

M

L

J 20 PL

M

B

M

0.25 (0.010) T

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A 25.66 27.171.010 1.070
B 6.10 6.600.240 0.260
C 3.81 4.570.150 0.180
D 0.39 0.550.015 0.022

G 2.54 BSC0.100 BSC
J 0.21 0.380.008 0.015
K 2.80 3.550.110 0.140
L 7.62 BSC0.300 BSC

M 0 15 0 15

N 0.51 1.010.020 0.040

____

E

1.27 1.770.050 0.070

1

11

10

20

–A–

SEATING
PLANE

K

N

FG

D

20 PL

–T–

M

A

M

0.25 (0.010) T

E

B

C

F

1.27 BSC0.050 BSC

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:

USA/EUROPE/ Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 5405; Denver, Colorado 80217. 1–800–441–2447 3–14–2 Ta tsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315

MFAX: RMF [e-mail] – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

INTERNET: http://Design–NET.com 51 Ting Ko k Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10H332/D

◊