Datasheet MC10EP16D Datasheet (Motorola)

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

 

Differential Receiver

The MC10EP16 is a differential receiver. The device is functionally
equivalent to the EL16 device with higher performance capabilities. With
output transition times significantly faster than the EL16 the EP16 is
ideally suited for interfacing with high frequency sources.

The EP16 provides a VBB output for either single-ended use or as a DC
bias for AC coupling to the device. The VBB pin should be used only as a
bias for the EP16 as its current sink/source capability is limited.
Whenever used, the VBB pin should be bypassed to ground via a 0.01µf
capacitor.

Under open input conditions (pulled to VEE) internal input clamps will
force the Q output LOW.

• 160ps Propagation Delay

• High Bandwidth Output Transitions

• 75kΩ Internal Input Pulldown Resistors

• >1000V ESD Protection

• Maximum Frequency > 2.7GHz

• V

Sink/Source Current = 0.5mA maximum

BB

• Component Count = 22 NPN devices

NOTE: Inputs have 75kΩ to VEE on D input and 75kΩ to VEE and VCC on D input

and when left open, force outputs to known state Q=Low, Q
temp 265°C for maximum for < 2–3 seconds; 245°C desired.

=High. Solder

MC10EP16

8–LEAD PLASTIC SOIC PACKAGE

PIN FUNCTION

D, D
Q, Q
V

BB Ref. Voltage Output

D SUFFIX

CASE 751-06

PIN DESCRIPTION

Data Inputs
Data Outputs

1

NC

75k

2

D

75k

D

3

75k

V

Figure 1. 8–Lead Pinout (Top View) and Logic Diagram

This document contains information on a product under development. Motorola reserves the right to change or
discontinue this product without notice.

3/98

 Motorola, Inc. 1998

45

BB

1

8

V

7

Q

6

Q

V

REV 0

CC

EE

MC10EP16

MAXIMUM RATINGS*

Symbol Parameter Value Unit

V

EE

V

I

I

out

T

A

V

EE

θ

JA

θ

JC

* Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the

Recommended Operating Conditions.

Power Supply (VCC = 0V) –8.0 to +0 VDC
Input Voltage (VCC = 0V) 0 to +–6.0 VDC
Output Current Continuous

Surge

50

100

mA

Operating Temperature Range –40 to +85 °C
Operating Range –5.5 to 3.0 V
Thermal Resistance (Junction–to–Ambient) Still Air

500lfpm

190
130

°C/W

Thermal Resistance (Junction–to–Case) 41 to 44 (±5%) °C/W

DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC =

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

V
V
V
V
V
V
I

IH

I

IL

IEE

Output HIGH Voltage –1080 –890 –1020 –840 –980 –810 –910 –720 mV

OH

Output LOW Voltage –1950 –1650 –1950 –1630 –1950 –1630 –1950 –1595 mV

OL

Input HIGH Voltage –1230 –890 –1170 –840 –1130 –810 –1060 –720 mV

IH

Input LOW Voltage –1950 –1500 –1950 –1480 –1950 –1480 –1950 –1445 mV

IL

Power Supply Voltage –5.5 –3.0 –5.5 –3.0 –5.5 –3.0 –5.5 –3.0 Volts

EE

Reference Voltage mV

BB

Input HIGH Current 150 150 150 150 µA
Input LOW Current DD0.5

–600

VEE Supply Current 23 29 23 29 23 29 23 29 mA

0.5

–600

GND; Note 1.)

0.5

–600

0.5

–600

µA
µA

1. 10EL circuits are designed to meet the DC specifications shown in the table after thermal equilibrium has been established. The circuit is in

a test socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. Outputs are terminated through
a 50Ω resistor to VCC –2.0V except where otherwise specified on the individual data sheets.

AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

f

max

t

PLH

t

PHL

t

SKEW

V
V
t

r

t

f

2. Minimum f

3. Duty cycle skew is the difference between a T

4. Minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40.

5. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within

Maximum Frequency (Note 2.) 2.7 2.7 2.7 2.7 GHz

,

Propagation Delay to Output Diff. 160 160 160 160 ps

Duty Cycle Skew (Note 3.) Diff. 5.0 5.0 20 5.0 20 5.0 20 ps
Minimum Input Swing (Note 4.) 150 150 150 150 mV

PP

Common Mode Range (Note 5.) –0.4 –0.4 –0.4 –0.4 V

CMR

Output Rise/Fall Times Q
(20% – 80%)

specified to 2.7GHz with reduced output swing. See Figure 2 on page 3.

max

110 110 110 110 ps

PLH

and T

propagation delay through a device.

PHL

the specified range and the peak-to-peak voltage lies between VPPmin and 1V . The lower end of the CMR range is dependent on VEE and is
equal to VEE + 2.5V.

MOTOROLA ECLinPS and ECLinPS Lite

2

DL140 — Rev 3

MC10EP16

PECL CHARACTERISTICS (Note 6.)

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

V
V
V
V
V
V

Power Supply Voltage 3.0 5.5 3.0 5.5 3.0 5.5 3.0 5.5 V

CC

Reference Voltage

BB

Output HIGH Voltage 3920 4110 3980 4160 4020 4190 4090 4280 mV

OH

Output LOW Voltage 3050 3350 3050 3370 3050 3370 3050 3405 mV

OL

Input HIGH Voltage 3770 4110 3830 4160 3870 4190 3940 4280 mV

IH

Input LOW Voltage 3050 3500 3050 3520 3050 3520 3050 3555 mV

IL

I

IH

I

IL

I

EE

Input HIGH Current 150 150 150 µA
Input LOW Current DD0.5

–600

VEE Supply Current 23 29 23 29 23 29 23 29 mA

0.5

–600

0.5

–600

0.5

–600

6. Input and output level parameters are for VCC=5.0V and levels will vary 1:1 with VCC.

LVPECL CHARACTERISTICS (Note 7.)

–40°C 0°C 25°C 85°C

Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit

V
V
V
V
V
V
I

IH

I

IL

I

EE

7. Input and output level parameters are for VCC=3.3V and levels will vary 1:1 with VCC.

Power Supply Voltage 3.0 5.5 3.0 5.5 3.0 5.5 3.0 5.5 V

CC

Reference Voltage

BB

Output HIGH Voltage 2220 2410 2280 2460 2320 2490 2390 2580 mV

OH

Output LOW Voltage 1350 1650 1350 1670 1350 1670 1650 1705 mV

OL

Input HIGH Voltage 2070 2410 2130 2460 2170 2490 2240 2580 mV

IH

Input LOW Voltage 1350 1800 1350 1820 1350 1820 1350 1855 mV

IL

Input HIGH Current 150 150 150 150 µA
Input LOW Current DD0.5

–600

VEE Supply Current 23 29 23 29 23 29 23 29 mA

0.5

–600

0.5

–600

0.5

–600

900

µA

µA

DL140 — Rev 3

800

700

600

PP (mV)

500

400

300

0.5 1.0 1.5 2.0 2.5 3.0 3.5
Frequency (GHz)

Figure 2. Frequency vs. Peak–to–Peak Jitter

3 MOTOROLAECLinPS and ECLinPS Lite

MC10EP16

OUTLINE DIMENSIONS

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751–06

ISSUE T

C

A

E

B

A1

D

58

0.25MB

1

H

4

e

M

h

X 45

_

q

C

A

SEATING
PLANE

0.10

L

B

SS

A0.25MCB

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.

2. DIMENSIONS ARE IN MILLIMETER.

3. DIMENSION D AND E DO NOT INCLUDE MOLD
PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.

5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS
OF THE B DIMENSION AT MAXIMUM MATERIAL
CONDITION.

MILLIMETERS

DIM MIN MAX

A 1.35 1.75

A1 0.10 0.25

B 0.35 0.49
C 0.19 0.25
D 4.80 5.00
E

3.80 4.00

1.27 BSCe

H 5.80 6.20
h

0.25 0.50

L 0.40 1.25

0 7

q

__

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE / Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141,

P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 4–32–1 Nishi–Gotanda, Shagawa–ku, Tokyo, Japan. 03–5487–8488

Customer Focus Center: 1–800–521–6274
Mfax: [e-mail] – TOUCHTONE 1–602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

Moto rola Fax Back System – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
HOME PAGE: http://motorola.com/sps/

– http://sps.motorola.com/mfax/

◊

MOTOROLA ECLinPS and ECLinPS Lite

4

Mfax is a trademark of Motorola, Inc.

MC10EP16/D

DL140 — Rev 3