Datasheet MC10116L, MC10116P Datasheet (Motorola)

Page 1



SEMICONDUCTOR TECHNICAL DATA

  

The MC10116 is a triple differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (VBB) is made available at pin 1 1 to make the device useful as a Schmitt trigger , or in other applications where a stable reference voltage is necessary.

Active current sources provide the MC10116 with excellent common mode noise rejection. If any amplifier in a package is not used, one input of that amplifier must be connected to VBB (pin 11) to prevent upsetting the current source bias network.

Complementary outputs are provided to allow driving twisted pair lines, to enable cascading of several amplifiers in a chain, or simply to provide complement outputs of the input logic function.

PD= 85 mW typ/pkg (No Load) tpd= 2.0 ns typ

tr, tf= 2.0 ns typ (20%–80%)

LOGIC DIAGRAM

4 5

10 12

VBB*

= PIN 1

CC1

= PIN 16

CC2 VEE= PIN 8

*VBB to be used to supply bias to the MC10116 only and bypassed (when used)

with 0.01 µF to 0.1 µF capacitor to ground (0 V). VBB can source < 1.0 mA.

When the input pin with the bubble goes positive, the output pin with the bubble goes positive.

2 3

6 7

14 15



L SUFFIX

CERAMIC PACKAGE

CASE 620–10

P SUFFIX

PLASTIC PACKAGE

CASE 648–08

FN SUFFIX

PLCC

CASE 775–02

DIP

PIN ASSIGNMENT

CC1

OUT

Pin assignment is for Dual–in–Line Package.

For PLCC pin assignment, see the Pin Conversion

T ables on page 6–11 of the Motorola MECL Data

1 2 3 4 5 6 7 8

Book (DL122/D).

16 15 14 13 12 11 10

CC2

OUT

3/93

 Motorola, Inc. 1996

3–63

REV 5

Page 2

MC10116

Under

ELECTRICAL CHARACTERISTICS

Test Limits

Characteristic Symbol

Power Supply Drain Current I Input Current I

Output Voltage Logic 1 V

Output Voltage Logic 0 V

Threshold Voltage Logic 1 V

Threshold Voltage Logic 0 V

Reference Voltage V Switching Times (50Ω Load) ns Propagation Delay t

Rise Time (20 to 80%) t

Fall Time (20 to 80%) t

inH

CBO

OHA

OLA

4+2+

4–2–

4+3–

4–3+

3+ 2–

3–

Under

Test

8 23 17 21 23 mAdc 4 150 95 95 µAdc 4 1.5 1.0 1.0 µAdc 2

3 2

11 –1.420 –1.280 –1.350 –1.230 –1.295 –1.150 Vdc

2 2 3 3

2 3

–30°C +25°C +85°C

Min Max Min Typ Max Min Max

–1.060 –1.060

–1.890 –1.890

–1.080 –1.080

1.0

1.1

–0.890 –0.890

–1.675 –1.675

–1.655 –1.655

3.1

3.6

–0.960 –0.960

–1.850 –1.850

–0.980 –0.980

1.0

1.1

2.0

–0.810 –0.810

–1.650 –1.650

–1.630 –1.630

2.9

3.3

–0.890 –0.890

–1.825 –1.825

–0.910 –0.910

1.0

1.1

–0.700 –0.700

–1.615 –1.615

–1.595 –1.595

3.3

3.7

Unit

Vdc

MOTOROLA MECL Data

3–64

DL122 — Rev 6

Page 3

MC10116

From

Und

(VCC)

ELECTRICAL CHARACTERISTICS (continued)

TEST VOLTAGE VALUES (Volts)

@ Test Temperature V

–30°C –0.890 –1.890 –1.205 –1.500 +25°C –0.810 –1.850 –1.105 –1.475 +85°C –0.700 –1.825 –1.035 –1.440

Characteristic Symbol

Power Supply Drain Current I Input Current I

Output Voltage Logic 1 V

Output Voltage Logic 0 V

Threshold Voltage Logic 1 V

Threshold Voltage Logic 0 V

Reference Voltage V Switching Times (50Ω Load) Pulse In Propagation Delay t

Rise Time (20 to 80%) t

Fall Time (20 to 80%) t

Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50-ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner.

inH

CBO

OHA

OLA

4+2+

4–2–

4+3–

4–3+

3+ 2–

3–

Test

11 5, 10, 13 8 1, 16

IHmaxVILminVIHAminVILAmax

8 4, 9, 12 5, 10, 13 8 1, 16 4 4 9, 12 5, 10, 13 8 1, 16 4 9, 12 5, 10, 13 8,4 1, 16 2

3 2

2 2 3 3

2 3

TEST VOLTAGE APPLIED TO PINS LISTED BELOW

IHmaxVILminVIHAminVILAmax

9, 12 9, 12

9, 12

4 4

9, 12 9, 12 4

9, 12

4 4 4 4

4 4

4 5, 10, 13

Pulse Out

2 2 3 3

2 3

From

5, 10, 13 5, 10, 13

5, 10, 13

5, 10, 13 5, 10, 13 5, 10, 13 5, 10, 13

5, 10, 13 5, 10, 13

–5.2 –5.2 –5.2

8 8

–3.2 V +2.0 V

8 8 8 8

8 8

Gnd

1, 16 1, 16

1, 16 1, 16 1, 16 1, 16

1, 16 1, 16

DL122 — Rev 6

3–65 MOTOROLAMECL Data

Page 4

MC10116

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 775–02

ISSUE C

–L–

20 1

0.010 (0.250) N

–N–

L–M

Y BRK

–M–

0.007 (0.180) N

0.004 (0.100)

–T–

VIEW S

SEATING PLANE

0.007 (0.180) N

L–M

0.010 (0.250) N

L–M

VIEW D–D

L–M

0.007 (0.180) N

L–M

0.007 (0.180) N

L–M

VIEW S

NOTES:

1. DATUMS –L–, –M–, AND –N– DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE.

2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DA TUM –T–, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).

MOTOROLA MECL Data

DIM MIN MAX MIN MAX

A 0.385 0.395 9.78 10.03 B 0.385 0.395 9.78 10.03 C 0.165 0.180 4.20 4.57 E 0.090 0.110 2.29 2.79 F 0.013 0.019 0.33 0.48 G 0.050 BSC 1.27 BSC H 0.026 0.032 0.66 0.81 J 0.020 ––– 0.51 ––– K 0.025 ––– 0.64 ––– R 0.350 0.356 8.89 9.04 U 0.350 0.356 8.89 9.04 V 0.042 0.048 1.07 1.21 W 0.042 0.048 1.07 1.21 X 0.042 0.056 1.07 1.42 Y ––– 0.020 ––– 0.50 Z 2 10 2 10

____

G1 0.310 0.330 7.88 8.38 K1 0.040 ––– 1.02 –––

3–66

MILLIMETERSINCHES

DL122 — Rev 6

Page 5

OUTLINE DIMENSIONS

CERAMIC DIP PACKAGE

–A–

16 9

–B–

–T–

SEATING PLANE

16 PLD

0.25 (0.010) T

–A–

916

16 PL

0.25 (0.010) T

PLASTIC DIP PACKAGE

SEATING

–T–

PLANE

L SUFFIX

CASE 620–10

ISSUE V

16 PLJ

0.25 (0.010) T

P SUFFIX

CASE 648–08

ISSUE R

MC10116

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL.

4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY.

DIM MIN MAX MIN MAX

A 0.750 0.785 19.05 19.93 B 0.240 0.295 6.10 7.49 C ––– 0.200 ––– 5.08 D 0.015 0.020 0.39 0.50 E 0.050 BSC 1.27 BSC F 0.055 0.065 1.40 1.65 G 0.100 BSC 2.54 BSC H 0.008 0.015 0.21 0.38 K 0.125 0.170 3.18 4.31

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

L 0.300 BSC 7.62 BSC M 0 15 0 15

____

N 0.020 0.040 0.51 1.01

Y14.5M, 1982.

FORMED PARALLEL.

DIM MIN MAX MIN MAX

A 0.740 0.770 18.80 19.55 B 0.250 0.270 6.35 6.85 C 0.145 0.175 3.69 4.44 D 0.015 0.021 0.39 0.53 F 0.040 0.70 1.02 1.77 G 0.100 BSC 2.54 BSC H 0.050 BSC 1.27 BSC J 0.008 0.015 0.21 0.38 K 0.110 0.130 2.80 3.30 L 0.295 0.305 7.50 7.74 M 0 10 0 10 S 0.020 0.040 0.51 1.01

MILLIMETERSINCHES

____

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.

How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315

MFAX: RMF AX0@email.sps.mot.com – T OUCHTONE 602–244–6609 ASIA/ PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, INTERNET: http://Design–NET .com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

MC10116/D

DL122 — Rev 6

◊

3–67 MOTOROLAMECL Data

*MC10116/D*

Datasheet MC10116L, MC10116P Datasheet (Motorola)

Specifications and Main Features

Frequently Asked Questions

User Manual