Page 1
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Differential Receiver
The MC100L VEL16 is a differential receiver. The device is functionally
equivalent to the EL16 device, operating from a low voltage supply. The
LVEL16 exhibits a wider CMR range than its EL16 counterpart. With
output transition times and propagation delays comparable to the EL16
the L VEL16 is ideally suited for interfacing with high frequency sources at
3.3V supplies.
The L VEL16 provides a VBB output for either single-ended use or as a
DC bias for AC coupling to the device. The VBB pin should be used only
as a bias for the LVEL16 as its current sink/source capability is limited.
Whenever used, the VBB pin should be bypassed to ground via a 0.01µf
capacitor.
Under open input conditions, the Q input will be pulled down to Vee and
the Q
input will be biased to VCC/2. This condition will force the Q output
low.
MC100LVEL16
8
1
• 300ps Propagation Delay
• High Bandwidth Output Transitions
• 75kΩ Internal Input Pulldown Resistors
• >2000V ESD Protection
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
1
NC
2
D
3
D
V
45
BB
V
8
CC
7
Q
6
Q
V
EE
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751-05
PIN DESCRIPTION
PIN FUNCTION
D Data Inputs
Q Data Outputs
V
BB Ref. Voltage Output
5/96
Motorola, Inc. 1996
4–1
REV 0
Page 2
MC100LVEL16
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
–40°C 0°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
V
BB
V
EE
I
IH
I
IL
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND)
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Min Typ Max Unit
t
PLH
t
PHL
t
SKEW
V
PP
V
CMR
t
r
t
f
1. Duty cycle skew is the difference between a TPLH and TPHL propagation delay through a device.
2. Minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈40.
3. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range varies 1:1 with VEE. The
numbers in the spec table assume a nominal VEE = –3.3V . Note for PECL operation, the V
Power Supply Current 17 23 17 23 17 23 18 24 mA
Output Reference Voltage –1.38 –1.26 –1.38 –1.26 –1.38 –1.26 –1.38 –1.26 V
Power Supply Voltage –3.0 –3.3 –3.8 –3.0 –3.3 –3.8 –3.0 –3.3 –3.8 –3.0 –3.3 –3.8 V
Input HIGH Current 150 150 150 150 µA
Input LOW Current DD0.5
Propagation Delay
to Output (Diff)
(SE)
Duty Cycle Skew1 (Diff) 5 30 5 20 5 20 5 20 ps
Minimum Input Swing
Common Mode Range
VPP < 500mV
VPP ≥ 500mV
Output Rise/Fall Times Q
(20% – 80%)
–600
–40°C 0°C 25°C 85°C
150
275
275
400
450
–0.4
–0.4
100
2
150 150 150 150 mV
3
–2.0
–1.8
120 220 320 120 220 320 120 220 320 120 220 320 ps
0.5
–600
215
165
–2.1
–1.9
290
290
365
415
–0.4
–0.4
0.5
–600
225
175
–2.1
–1.9
0.5
–600
300
375
425
–0.4
–0.4
240
190
–2.1
–1.9
300
(min) will be fixed at 3.3V – |V
CMR
315
315
390
440
–0.4
–0.4
CMR
µA
ps
V
(min)|.
MOTOROLA ECLinPS and ECLinPS Lite
4–2
DL140 — Rev 3
Page 3
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751–05
ISSUE M
MC100LVEL16
–T–
–A–
58
4X P
–B–
14
C
SEATING
PLANE
8X D
K
0.25 (0.010)MB
SS
A0.25 (0.010)MTB
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
M
R
X 45
_
_
M
J
F
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
DIM MIN MAX MIN MAX
A 4.80 5.00 0.189 0.196
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.050 BSC
J 0.18 0.25 0.007 0.009
K 0.10 0.25 0.004 0.009
M 0 7 0 7
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
INCHESMILLIMETERS
____
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “T ypical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: RMF AX0@email.sps.mot.com – T OUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET .com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC100LVEL16/D
DL140 — Rev 3
◊
4–3 MOTOROLAECLinPS and ECLinPS Lite
*MC100LVEL16/D*
Loading...