Page 1
MBR1060, MBR1080,
MBR1090, MBR10100
MBR1060 and MBR10100 are Preferred Devices
SWITCHMODE
Power Rectifiers
. . . using the Schottky Barrier principle with a platinum barrier
metal. These state–of–the–art devices have the following features:
• Guard–Ring for Stress Protection
• Low Forward Voltage
• 150°C Operating Junction Temperature
• Epoxy Meets UL94, VO at 1/8″
• Low Power Loss/High Efficiency
• High Surge Capacity
• Low Stored Charge Majority Carrier Conduction
Mechanical Characteristics:
• Case: Epoxy, Molded
• Weight: 1.9 grams (approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
• Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
• Shipped 50 units per plastic tube
• Marking: B1060, B1080, B1090, B10100
MAXIMUM RATINGS
Please See the Table on the Following Page
http://onsemi.com
SCHOTTKY BARRIER
RECTIFIERS
10 AMPERES
60 to 100 VOLTS
3 1, 4
4
1
3
TO–220AC
CASE 221B
PLASTIC
Semiconductor Components Industries, LLC, 2000
October, 2000 – Rev. 3
MARKING DIAGRAM
B10x0
B10x0 = Device Code
x = 6, 8, 9 or 10
ORDERING INFORMATION
Device Package Shipping
MBR1060 TO–220
MBR1080 TO–220 50 Units/Rail
MBR1090 TO–220 50 Units/Rail
MBR10100 TO–220 50 Units/Rail
Preferred devices are recommended choices for future use
and best overall value.
1 Publication Order Number:
50 Units/Rail
MBR1060/D
Page 2
MBR1060, MBR1080, MBR1090, MBR10100
MAXIMUM RATINGS
Rating Symbol
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Average Rectified Forward Current (Rated VR) TC = 133°C I
Peak Repetitive Forward Current
(Rated V
, Square Wave, 20 kHz) TC = 133°C
R
Nonrepetitive Peak Surge Current
V
V
F(AV)
I
I
RRM
RWM
V
FRM
FSM
1060 1080 1090 10100
60 80 90 100 Volts
R
(Surge applied at rated load conditions halfwave, single phase, 60 Hz)
Peak Repetitive Reverse Surge Current (2.0 µs, 1.0 kHz) I
Operating Junction Temperature T
Storage Temperature T
RRM
J
stg
Voltage Rate of Change (Rated VR) dv/dt 10,000 V/µs
THERMAL CHARACTERISTICS
Maximum Thermal Resistance — Junction to Case
— Junction to Ambient
R
θ
JC
R
θ
JA
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 1.)
(i
= 10 Amps, TC = 125°C)
F
= 10 Amps, TC = 25°C)
(i
F
(i
= 20 Amps, TC = 125°C)
F
(i
= 20 Amps, TC = 25°C)
F
Maximum Instantaneous Reverse Current (Note 1.)
(Rated dc Voltage, T
(Rated dc Voltage, T
= 125°C)
C
= 25°C)
C
1. Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤2.0%.
v
F
i
R
MBR
10 Amps
20 Amps
150 Amps
0.5 Amp
65 to +150 °C
65 to +175 °C
2.0
60
0.7
0.8
0.85
0.95
6.0
0.10
Unit
°C/W
Volts
mA
http://onsemi.com
2
Page 3
MBR1060, MBR1080, MBR1090, MBR10100
50
20
150°C
10
125°C
100°C
5.0
3.0
T
= 25°C
J
1.0
0.5
, INSTANTANEOUS FORWARD CURRENT (AMPS)
F
i
0.2 0.4 0.8 20 40 60
v
, INSTANTANEOUS VOLTAGE (VOLTS)
F
0.60
0.50.1 0.3 0.7 0.9 100
1.0 140
Figure 1. Typical Forward Voltage Figure 2. Typical Reverse Current
10
9.0 9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
, AVERAGE FORWARD CURRENT (AMPS)
1.0
F(AV)
0
I
110
SQUARE WAVE
dc
RATED VOLTAGE APPLIED
R
= 2°C/W
JC
120 130 140 150 60 80 160
, CASE TEMPERATURE (°C)
T
C
160
10
1.0
0.1
, REVERSE CURRENT (mA)
R
I
0.01
10
8.0
7.0
6.0
5.0
4.0
3.0
2.0
, AVERAGE FORWARD CURRENT (AMPS)
1.0
F(AV)
I
T
= 150°C
J
125°C
100°C
25°C
0
80
120
VR, REVERSE VOLTAGE (VOLTS)
(HEATSINK)
R
= 16°C/W
JA
(NO HEATSINK)
= 60°C/W
R
JA
RATED VOLTAGE
APPLIED
dc
dc
SQUARE WAVE
0
200
40
, AMBIENT TEMPERATURE (°C)
T
A
100 120 140
180 200
Figure 3. Current Derating, Case Figure 4. Current Derating, Ambient
10
T
9.0
= 25°C
A
8.0
IPK/IAV =
dc
SQUARE WAVE
, AVERAGE POWER DISSIPATION (WATTS)
F(AV)
P
7.0
6.0
5.0
4.0
IPK/IAV = 10
IPK/IAV = 20
IPK/IAV = 5.0
3.0
2.0
1.0
0
1.0 7.0 8.0 9.0
3.0
2.0 4.00
, AVERAGE CURRENT (AMPS)
I
F(AV)
5.0 106.0
Figure 5. Forward Power Dissipation
http://onsemi.com
3
Page 4
MBR1060, MBR1080, MBR1090, MBR10100
PACKAGE DIMENSIONS
TO–220
PLASTIC
CASE 221B–04
ISSUE D
C
Q
B
4
13
H
L
G
F
T
S
A
U
K
D
R
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
DIM MIN MAX MIN MAX
A 0.595 0.620 15.11 15.75
B 0.380 0.405 9.65 10.29
C 0.160 0.190 4.06 4.82
D 0.025 0.035 0.64 0.89
F 0.142 0.147 3.61 3.73
G 0.190 0.210 4.83 5.33
H 0.110 0.130 2.79 3.30
J 0.018 0.025 0.46 0.64
K 0.500 0.562 12.70 14.27
L 0.045 0.060 1.14 1.52
Q 0.100 0.120 2.54 3.04
R 0.080 0.110 2.04 2.79
S 0.045 0.055 1.14 1.39
T 0.235 0.255 5.97 6.48
U 0.000 0.050 0.000 1.27
MILLIMETERSINCHES
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: [email protected]
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, UK, Ireland
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
Toll–Free from Mexico: Dial 01–800–288–2872 for Access –
then Dial 866–297–9322
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
http://onsemi.com
4
MBR1060/D
Loading...