Datasheet MAAVCC0001, MAAVCC0001TR, MAAVCC0001-TB Datasheet (M A COM)

Page 1
MAAVCC0001
Voltage Variable Absorptive Attenuator 800 - 1000 MHz
CSP-8, 28 Lead, 6mm Features
n Input IP3: +31 dBm Min. (Full Attenuation Range) n Input IP3 is 15 -20 dB Better Than GaAs n Linear Operation: +20 dBm Min. n Plastic, 28 Lead, 6 mm CSP, SMT Package n 38 dB Dynamic Range (With 30 mA Bias Current) n Single Control Voltage n 50 ohm Impedance n Linear Driver, DR65-0002, Available n Test Boards are Available n Tape and Reel Packaging Available
Description
M/A-COM's MAAVCC0001 is a PIN diode based voltage variable attenuator. This device is in a 6mm square, 28 lead, plastic CSP Package, suitable for surface mounting on PCBs. These attenuators have linear operating power and input intercept point levels 15 - 20 dB better than GaAs FET MMIC voltage variable attenuators. They are ideally suited for use where low distortion, high linear operating power and high dynamic range are required. These devices are optimized for the GSM frequency band, but exhibit excellent performance and repeatability over the entire specified frequency band. The MAAVCC0001 is ideally suited for wireless communications systems.
Package outline conforms to JEDEC standard MO-220B.
V 2.00
Electrical Specifications: TA = 25°C
Parameter Test Conditions Frequency Units Min. Typ. Max.
Insertion Loss 0 volts 800-1000 MHz
Attenuation
(Above Loss)
Frequency
Flatness
VSWR 0 to 30 dB attenuation 800-1000 MHz
Switching Speed 50% Control to 90%/10% RF 800-1000 MHz µS 10.0
Linear Operation 800-1000 MHz dBm +20
Input IP
3
I
Control
12 mA bias current 800-1000 MHz
0 to 30 dB attenuation 800-1000 MHz
Two-tone inputs up to +10 dBm 800-1000 MHz dBm +35 +40 —-
800-1000 MHz mA 30
925 - 960 MHz
925 - 960 MHz
925 - 960 MHz
925 - 960 MHz
dB dB
dB dB
dB dB
Ratio Ratio
— —
30 30
— —
— —
3.6
3.5 34
34
2.3
0.4
1.5:1
1.3:1
4.2
3.9 —
3.0
0.8
1.9:1
1.8:1
Page 2
Voltage Variable Absorptive Attenuator 800 - 1000 MHz
+85°C
30 dB
5 dB
Typical Performance Curves
MAAVCC0001
V 2.00
Insertion Loss
+25°C-40°C
4.5
4.0
3.5
Loss (dB)
3.0
2.5 800 850 900 950 1000
Frequency (MHz)
10 dB
1.5
1.0
0.5
0.0
-0.5
Flatness (dB)
-1.0
-1.5 800 850 900 950 1000
Frequency (MHz)
20 dB
Typical VSWR @ +25°C
15 dB 30 dB Ref
1.8
1.6
1.4
VSWR (Ratio)
1.2
1
800 850 900 950 1000
Frequency (MHz)
Atten. vs. Bias Current @ +25°C Attenuation Flatness @ +25°C
0
-5
-10
-15
-20
-25
-30
Attenuation (dB)
-35
-40 0 1 2 3 4 5 6 7 8 9 10 11 12
Current (mA)
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
2
Page 3
Voltage Variable Absorptive Attenuator 800 - 1000 MHz
MAAVCC0001
V 2.00
Pin Configuration
Pin # Function Pin # Function
1 N/C 15 N/C 2 N/C 16 N/C 3 N/C 17 N/C 4 N/C 18 N/C 5 N/C 19 N/C 6 N/C 20 N/C 7 N/C 21 N/C 8 N/C 22 N/C
9 Bias 10 N/C 24 Bias 11 N/C 25 N/C 12 GND 26 GND 13 RF out 27 RF in 14 GND 28 GND
1. Bias current may be applied to Pin 9 or 24. However, the unused Pin must be isolated.
1
23 N/c
Recommended PCB Layout
1
Absolute Maximum Ratings 2
Parameter Absolute Maximum
Max. Input Power +27 dBm
Operating Temperature -40°C to +85°C
Storage Temperature -65°C to +125°C
2. Operation of this device above any one of these parameters may cause permanent damage.
Ordering Information
Part Number Package
MAAVCC0001 Bulk Packaging
MAAVCC0001TR Tape and Reel (1K Reel)
MAAVCC0001-TB Unit Mounted on Test Board
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
3
Loading...