Page 1
) Preliminary Specification
(
( V ) Final Specification
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
Module
Model Name
22” WXGA+ Color TFT-LCD
M220EW01 V4
Customer Date
www.jxlcd.com
www.jxlcd.com
Approved by
FOR PROMATE INTERNAL USE ONLY
Checked &
Approved by
CM Wung
Prepared by
Date
2007/08/22
Note: This Specification is subject to change without
notice.
document version 1.0 1
Boris Chu
Desktop Display Business Group /
AU Optronics corporation
2007/08/22
Page 2
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
Contents
1. Handling Precautions.............................................................................................................. 4
2. General Description ................................................................................................................ 5
2.1 Display Characteristics .......................................................................................................................5
3. Functional Block Diagram .................................................................................................... 11
4. Absolute Maximum Ratings.................................................................................................. 12
4.1 Absolute Ratings of TFT LCD Module............................................................................................. 12
4.2 Absolute Ratings of Backlight Unit .................................................................................................. 12
4.3 Absolute Ratings of Environment..................................................................................................... 13
5. Electrical characteristics ...................................................................................................... 14
5.1 TFT LCD Module ............................................................................................................................. 14
5.2 Backlight Unit................................................................................................................................... 16
6. Signal Characteristic............................................................................................................. 17
6.1 Pixel Format Image........................................................................................................................... 17
6.2 The Input Data Format ...................................................................................................................... 18
6.4 Interface Timing................................................................................................................................ 21
6.5 Power ON/OFF Sequence................................................................................................................. 23
7. Connector & Pin Assignment ............................................................................................... 24
7.1 TFT LCD Module ............................................................................................................................. 24
7.2 Backlight Unit................................................................................................................................... 25
8. Reliability Test ....................................................................................................................... 26
9. Shipping Label....................................................................................................................... 27
10. Mechanical Characteristics ................................................................................................ 28
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 2
Page 3
Product Specification
28.5W (Typ) (Without Invertor, All black
SPD Measurement is defined
At 75Hz,
At 75Hz,
AU OPTRONICS CORPORATION
M220EW01 V4
Version and
Date
0.1 2007/04/19 All First Edition for Customer All
Page
Old description New Description Remark
1.0 2007/08/22 5
1.0 2007/08/22 15
1.0 2007/08/22 5
1.0 2007/08/22 5
1.0 2007/08/22 6
1.0 2007/08/22 9~10
1.0 2007/08/22 14
www.jxlcd.com
www.jxlcd.com
1.0 2007/08/22 14
FOR PROMATE INTERNAL USE ONLY
Surface Treatment：Hard-coating (3H),
Non-glare type
CCFL Life Time(LTCFL)：Typ => TBD
Optical ResponseTime：
5 (Typ, on/off)
Power Consumption
(VDD line + CCFL line)
pattern)
NA
NA
IDD：Input Current
Min Typ Max
- 890 1500
VDD= 5.0V, All black pattern At 60Hz
PDD：VDD Power
Min Typ Max
- 5 7
VDD= 5.0V, All black pattern At 60Hz
Surface Treatment：Hard-coating (3H),
Non-glare type, reflection ratio 2.5%
CCFL Life Time(LTCFL)：Typ => 50,000
Optical ResponseTime：
5 (Typ, on/off); 8 (Typ, SPD on)
Power Consumption
(VDD line + CCFL line)
28.5W (Typ) SPD off / 32W (Typ) SPD
on (Without Invertor, All black pattern)
Optical Response Time
Min Typ Max
MPRT - 8 15
Note 8:
as below:
IDD：Input Current
Min Typ Max
- 890 1500
VDD= 5.0V, All black pattern At 60Hz
- 1200 1800
VDD= 5.0V, All black pattern
SPD on
IDD：Input Current
Min Typ Max
- 5 7
VDD= 5.0V, All black pattern At 60Hz
- 6 8
VDD= 5.0V, All black pattern
SPD on
Revised
Revised
Revised
Revised
Revised
Revised
Revised
Revised
document version 1.0 3
Page 4
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CCFL reflector edge. Instead, press at the far
ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 4
Page 5
Product Specification
RoHS Compliance
AU OPTRONICS CORPORATION
M220EW01 V4
2. General Description
This specification applies to the 22 inch-wide Color TFT-LCD Module M220EW01.
The display supports the WSXGA+ (1680(H) x 1050(V)) screen format and 16.7M colors. All input signals are 2
Channel LVDS interface compatible.
This module does not contain an inverter card for backlight..
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition:
Items Unit Specifications
Active Area [mm] 473.76 (H) x 296.1(V)
Pixels H x V 1680x3(RGB) x 1050
Pixel Pitch [mm] 0.282x 0.282
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode,Normally White
White Luminance [cd/m2]
Contrast Ratio 1000:1 (Typ)
Optical ResponseTime [msec] 5 (Typ, on/off); 8 (Typ, SPD on)
Nominal Input Voltage VDD [Volt] +5.0 V
www.jxlcd.com
www.jxlcd.com
300 cd/m
2 @ 7.0mA
(Typ)
FOR PROMATE INTERNAL USE ONLY
Power Consumption
(VDD line + CCFL line)
Weight [Grams]
Physical Size (H x V x D) [mm] 493.7(W) x 320.1(H) x 16.7(D) (Typ)
Electrical Interface Dual Channel LVDS
Support Colors 16.7M colors (6-bits + HiFRC)
Temperature Range
Operating
Storage (Shipping)
[Watt]
[oC]
[oC]
28.5W (Typ) SPD off / 32W (Typ) SPD on
(Without Invertor, All black pattern)
2385 Note1
0 to +50
-20 to +60
Surface Treatment
RoHS Compliance
Note1: 2500 gm (Max)
document version 1.0 5
Hard-coating (3H), Non-glare type
reflection ratio 2.5%
Page 6
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):Except
MPRT, all data are measured with SPD OFF.
Item Unit Conditions Min. Typ. Max. Note
Horizontal
(Right)+ (Left)
CR = 10
Viewing Angle [degree]
Vertical
(Up) + (Down)
CR = 10
160 170
150 160
-
-
1
Luminance Uniformity [%] 9 Points
Rising -
Falling -
Optical Response Time [msec]
Rising + Falling -
MPRT
www.jxlcd.com
www.jxlcd.com
Color / Chromaticity
Coordinates
(CIE 1931)
White Luminance
(At CCFL= 7.0mA)
FOR PROMATE INTERNAL USE ONLY
[cd/m2 ]
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
75 80
3.6
1.4 2.3
5 8
-
0.628 0.658 0.688
0.301 0.331 0.361
0.178 0.208 0.238
0.649 0.679 0.709
0.117 0.147 0.177
0.035 0.065 0.095
0.283 0.313 0.343
0.299 0.329 0.359
240 300 -
8 15
- 2, 3
5.7
4, 6
8
4
4
Contrast Ratio Normal Direction
Cross Talk (At 75Hz) [%]
Flicker [dB]
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
document version 1.0 6
600 1000 -
- - 1.5
- - -20
4
5
7
Page 7
Product Specification
Minimum
Luminance
of 9 points
=
Max
imum
Luminance
of 9 points
50 %
90 %
90 %
50 %
10 %
10 %
AU OPTRONICS CORPORATION
Note 1: Definition of viewing angle: measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal
and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as
follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The
measurement direction is typically perpendicular to the display surface with the screen rotated about its
center to develop the desired measurement viewing angle.
M220EW01 V4
Note 2: 9 points position
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance
document version 1.0 7
δ
W9
Page 8
Product Specification
TFT-LCD Module
LCD Panel
AU OPTRONICS CORPORATION
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
M220EW01 V4
Photo detector
Field=2°
50 cm
www.jxlcd.com
Note 5: Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
www.jxlcd.com
Center of the screen
FOR PROMATE INTERNAL USE ONLY
document version 1.0 8
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Page 9
Product Specification
Level
DC
AU OPTRONICS CORPORATION
Note 6: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response time
is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.
M220EW01 V4
Note 7: Subchecker Pattern
R G B R G B
Gray Level = L127
R G B R G B
R G B R G B
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
www.jxlcd.com
www.jxlcd.com
Gray Level = L0
FOR PROMATE INTERNAL USE ONLY
AC
DC
Time
Note 8: SPD Measurement is defined as below: measured by Otsuka MPRT-1000
MPRT(Moving Picture Response Time) is the average value of BET measured from 72
combinations of different gray levels.
We divide the measurement base on each 32 grey level. Because the brightness between L0 &
document version 1.0 9
log20(dB)Flicker =
Hz) 30Level(at AC
Page 10
Product Specification
72
AU OPTRONICS CORPORATION
L32 is so slight and it will cause noise to influence the outcome, we set L42 instead of L32. We can
get 72 combination data as the table below.
M220EW01 V4
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
BET...BETBET
(seconds) MPRT
BEW BET
BEW: Blur Edge Width (LCD pixel). The width is defined to be used for the values 10%~90% of
luminance.
Note: scrolling speed=8ppf (LCD pixel/frame rate) ; frame rate=75Hz
=
1
×=
×
+++
7221
rate frame speed scrolling
document version 1.0 10
Page 11
Product Specification
Connector
I/F + X
-
PCB
AU OPTRONICS CORPORATION
M220EW01 V4
3. Functional Block Diagram
The following diagram shows the functional block of the 22 inches wide Color TFT-LCD Module:
VDD=5V
LVDS
Receiver
DC/DC
Converter
www.jxlcd.com
www.jxlcd.com
Correction
Timing
Controller
Gamma
FOR PROMATE INTERNAL USE ONLY
G1
G1050
TFT-LCD
1680*(3)*1050
Pixels
D1 D5040
4 CCFL
Inverter
MDF76URW-30S-1H
FI-XB30SSRL-HF16 or compatible
Mating Type: FI-X30S-H
document version 1.0 11
YEON HO 35001HS-02L or compatible
Mating Type: 35001WR-02L or
SM02B-BHSS-1-TB
Page 12
Product Specification
Voltage
AU OPTRONICS CORPORATION
4. Absolute Maximum Ratings
Absolutely maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions
M220EW01 V4
Logic/LCD Drive
VDD -0.3 +5.5 [Volt] Note 1, 2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Conditions
CCFL Current ICFL - 8 [mA] rms Note 1, 2
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 12
Page 13
Product Specification
AU OPTRONICS CORPORATION
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions
M220EW01 V4
Operating Temperature
Operation Humidity HOP 5 90 [%RH]
Storage Temperature TST -20 +60 [oC]
Storage Humidity HST
Note 1: With in Ta= 25℃
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [oC]
8 90
[%RH]
Note 3
FOR PROMATE INTERNAL USE ONLY
Operating Range Storage Range
document version 1.0 13
Page 14
Product Specification
90%
10%
M220EW01 V4
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition
VDD
Logic/LCD Drive
Voltage
4.5 5.0 5.5 [Volt] ±10%
- 890 1500 [mA]
VDD= 5.0V, All black pattern
At 60Hz, SPD off
IDD Input Current
1200 1800 [mA]
- 5 7 [Watt]
VDD= 5.0V, All black pattern
At 75Hz, SPD on
VDD= 5.0V, All black pattern
At 60Hz, SPD off, Note 1
PDD VDD Power
6 8 [Watt]
VDD= 5.0V, All black pattern
At 75Hz, SPD on
IRush Inrush Current - - 2.5 [A] Note 2
VDDrp
Note 1: The variance of VDD power consumption is ±10% and SPD function turn on
Note 2: Measurement conditions:
(High to Low)
Control
Signal
Drive Ripple Voltage
www.jxlcd.com
www.jxlcd.com
+5.0V
FOR PROMATE INTERNAL USE ONLY
R1
47K
R2
100
Q3
AO6402
D6
D5
D2 S
D1
G
D2SD1D5
D6
G
Q3
AO6402
F1
Allowable logic/LCD
[mV]
p-p
VDD=5.0, All black pattern at
60Hz
(LCD Module Input)
C1
1uF/16V
VCC
1K
SW1
SW MAG-SPST
1 2
+12.0V
C2
1uF/25V
VR1
47K
C3
0.01uF/25V
5.0V
document version 1.0 14
VDD rising time
0V
0.5ms
Page 15
Product Specification
VID│
GND
AU OPTRONICS CORPORATION
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
Each signal characteristics are as follows;
M220EW01 V4
Symbol Parameter Min Typ
VTH
VTL
│VID│
VICM
Note: LVDS Signal Waveform
VTH
VTL
Differential Input
High Threshold
Differential Input
Low Threshold
Input Differential
Voltage
Differential Input
Common Mode
Voltage
www.jxlcd.com
www.jxlcd.com
VICM
- -
-100 -
100 400
1.0 1.2 1.5 [V]
FOR PROMATE INTERNAL USE ONLY
Max Units Condition
100 [mV]
- [mV]
600 [mV]
VICM = 1.2V Note
VICM = 1.2V Note
Note
VTH/VTL = ± 100mV
│
document version 1.0 15
Page 16
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
5.2 Backlight Unit
Parameter guideline for CCFL Inverter is under stable conditions at 25 (Room Temperature):
Parameter Min. Typ. Max. Unit Condition
CCFL Standard Current (ICFL)
CCFL Operation Current(IOCFL) 3.5 7.0 8.0 [mA] rms Note 2
CCFL Frequency(FCFL) 40 50 60 [KHz] Note 3,4
CCFL Ignition Voltage(ViCFL, Ta= 0)
(End of the lamp wire connector)
CCFL Ignition Voltage(ViCF, Ta= 25)
(End of the lamp wire connector)
CCFL Operation Voltage (VCFL) -
CCFL Power Consumption(PCFL) - 22.6 24.6 [Watt] Note 6
CCFL Life Time(LTCFL) 40,000 50,000 - [Hour] Note 7
Note 1: Typ. are AUO recommended design points.
*1 All of characteristics listed are measured under the condition using the AUO test inverter.
www.jxlcd.com
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.
Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker
at low power may happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of
CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
6.5 7.0 7.5
1730 - - [Volt] rms
1330 - - [Volt] rms
806
(@ 7.0mA)
[mA] rms Note 2
Note 5
[Volt] rms Note 6
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is
recommended to keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL
discharge frequency. So all the parameters of an inverter should be carefully designed so as not
to produce too much leakage current from high-voltage output of the inverter.
Note 2: It should be employed the inverter which has “Duty Dimming”, if IRCFL is less than 4mA.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter
and TFT LCD.
Note 4: The frequency range will not affect to lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,730
voltage. Lamp units need 1,730 voltage minimum for ignition.
Note 6: The variance of CCFL power consumption is ±10%. Calculator value for reference (ISCFL × VCFL ×
4 = PCFL)
Note 7: Definition of CCFL life Time (LTCFL): brightness becomes 50%. (The typical life time of CCFL is on
the condition at 7.0 mA lamp current).
document version 1.0 16
Page 17
Product Specification
R G B R G B
R G B R G B
R G B R G B
R G B R G B
1 2 1679 1680
1st Line
1050 Line
AU OPTRONICS CORPORATION
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
M220EW01 V4
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 17
Page 18
6.2 The Input Data Format
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
Note1: Normally, DE, VS, HS on EVEN channel are not used.
Note2: 8-bits signal input.
Note3: L:NS alike H:Thine alike
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 18
Page 19
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels
while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, H-Sync, V-Sync, DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, H-Sync, V-Sync, DSPTMG)
7 GND Power Ground
8 RxOCLKIN- Negative LVDS differential clock input (Odd clock)
9 RxOCLKIN+
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 GND Power Ground
www.jxlcd.com
15 RxEIN1- Positive LVDS differential data input (Even data)
16 RxEIN1+ Negative LVDS differential data input (Even data)
17 GND Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLKIN- Negative LVDS differential clock input (Even clock)
21 RxECLKIN+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 GND Power Ground
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
Positive LVDS differential clock input (Odd clock)
25 AGMODE L: enable
26 HVS H: 5V enable
27 SPDEN L: enable
28 POWER +5.0V Power Supply
29 POWER +5.0V Power Supply
30 POWER +5.0V Power Supply
document version 1.0 19
Page 20
Connector
RxO
IN
0
-
V
DD
Note1: Start from left side
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow PSWG.
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
30
document version 1.0 20
Page 21
6.4 Interface Timing
6.4.1 Timing Characteristics
Signal Item Symbol Min Typ Max Unit
Period Tv
Vertical
Section
Active Tdisp(v) 1050 1050 1050 Th
Blanking Tbp(v)+Tfp(v)+PWvs 8 16 998 Th
Product Specification
AU OPTRONICS CORPORATION
1058 1066 2048 Th
M220EW01 V4
Horizontal
Section
Clock
Frame Rate Frequency 1/Tv 50 60 75 Hz
Note : DE mode only
Period Th 880 1128 2048 Tclk
Active Tdisp(h) 840 840 840 Tclk
Blanking Tbp(h)+Tfp(h)+PWhs 40 288 1208 Tclk
Period Tclk 11.76 13.86 16.67 ns
Frequency Freq. 60 72.1 85 MHz
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 21
Page 22
6.4.2 Timing Diagram
Product Specification
M220EW01 V4
AU OPTRONICS CORPORATION
RGB Data
(Odd)
RGB Data
(Even)
DE
Invalid Data
Invalid Data
Tbp(h)
Pixel
Pixel
2
1
Pixel Pixel
Pixel
3 9 M-1
4
Pixel
6
5 M-3
www.jxlcd.com
www.jxlcd.com
Pixel Pixel Pixel Pixel Pixel Pixel
7
8
FOR PROMATE INTERNAL USE ONLY
10
11
12
Tdisp(h)
Hsync
PWhs
CLK
Tclk
RGB Data
DE
Line Line Line Line Line Line
N
Invalid Data
2
43
Hsync
Tfp(v)
Tbp(v)
Tdisp(v)
Vsync
PWvs
Tv
M-4
M-2
M
Invalid Data
document version 1.0 22
PixelPixel
Tfp(h)
Invalid Data
N1
Th
Invalid Data
PixelPixelPixelPixel
M-5
Page 23
Product Specification
T5
T2
T1
T6
AU OPTRONICS CORPORATION
M220EW01 V4
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off.
VALID
DATA
90%
10%
T7
T4
Power Supply VDD
LVDS Signal
Backlight On
90%
10%
T3
www.jxlcd.com
www.jxlcd.com
Power Sequence Timing
Parameter
FOR PROMATE INTERNAL USE ONLY
Value
Unit
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 40 50 [ms]
T3 200 - - [ms]
T4 200 - - [ms]
T5 0.5 16 50 [ms]
T6 - - 100 [ms]
T7 1000 - - [ms]
document version 1.0 23
Page 24
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card
Manufacturer
LVDS: HIROSE/ JAE or compatible
Type Part Number
Mating Housing Part Number
7.1.2 Pin Assignment
Pin# Signal Name Pin# Signal Name
1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 GND 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 GND
15 RxEIN1- 16 RxEIN1+
17 GND 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
LVDS :MDF76URW-30S-1H/ FI-XB30SSRL-HF16
FI-X30S-H ( Unlocked Type ) or equivalent
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 GND
25 AGMODE 26 HVS
27 SPDEN 28 POWER
29 POWER 30 POWER
Note : pin 25H (3.3V) or Floating disable AGMODE
pin 26 L or Floating disable HVS
document version 1.0 24
pin 27 H(3.3V) or Floating disable SPDEN
Page 25
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
Connector Name / Designation Lamp Connector / Backlight lamp
Manufacturer
Type Part Number
Mating Type Part Number
7.2.1 Signal for Lamp connector
Upper
Connector No.
CN1
CN2
www.jxlcd.com
www.jxlcd.com
Pin No. Input Color Function
1 Hot1 Sky Blue High Voltage (Lamp 1)
2 Cold1 Black Low Voltage (Lamp 1)
1 Hot2 Pink High Voltage (Lamp 2)
2 Cold2 W hite Low Voltage (Lamp 2)
Lower
Connector No.
FOR PROMATE INTERNAL USE ONLY
CN3
CN4
Pin No. Input Color Function
1 Hot1 Sky Blue High Voltage (Lamp 3)
2 Cold1 Black Low Voltage (Lamp 3)
1 Hot2 Pink High Voltage (Lamp 4)
2 Cold2 White Low Voltage (Lamp 4)
YEONHO or compatible
35001HS-02L
35001WR-02L or SM02B-BHSS-1-TB
document version 1.0 25
Page 26
Product Specification
AU OPTRONICS CORPORATION
8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition
Temperature Humidity Bias (THB) Ta= 50, 80%RH, 300hours
M220EW01 V4
Note
High Temperature Operation (HTO) Ta= 50, 300hours
Low Temperature Operation (LTO) Ta= 0, 300hours
High Temperature Storage (HTS) Ta= 60, 300hours
Low Temperature Storage (LTS) Ta= -20, 300hours
Acceleration: 1.5 G
Vibration Test
(Non-operation)
Shock Test
(Non-operation)
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -20/30min, 60/30min, 100 cycles
On/Off Test On/10sec, Off/10sec, 30,000 cycles
ESD (ElectroStatic Discharge)
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
Wave: Random
Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Wave: Half-sine
Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.
1
2
Altitude Test
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20℃ to 60℃, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
document version 1.0 26
Operation:10,000 ft
Non-Operation:30,000 ft
Page 27
Product Specification
AU OPTRONICS CORPORATION
9. Shipping Label
The shipping label format is shown as below.
M220EW01 V4
www.jxlcd.com
www.jxlcd.com
FOR PROMATE INTERNAL USE ONLY
document version 1.0 27
Page 28
Product Specification
AU OPTRONICS CORPORATION
10. Mechanical Characteristics
M220EW01 V4
www.jxlcd.com
www.jxlcd.com
document version 1.0 28
FOR PROMATE INTERNAL USE ONLY
Page 29
Product Specification
AU OPTRONICS CORPORATION
M220EW01 V4
www.jxlcd.com
www.jxlcd.com
document version 1.0 29
FOR PROMATE INTERNAL USE ONLY
Loading...