Datasheet M200O1-L03 Datasheet (Chi Mei Optoelectronics)

Page 1
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
TFT LCD Approval Specification
MODEL NO.: M200O1- L03
Customer:
Approved by:
Note:
www.jxlcd.com
www.jxlcd.com
核准時間 部門 審核 角色 投票
2009-07-01
09:32:48
MTR
產品管理處
2009.07.01
柏 勳
Director Accept
1 / 29
Version 2.0
Page 2
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
- CONTENTS -
REVISION HISTORY ............................................................................................................................... 4
1. GENERAL DESCRIPTION .................................................................................................................. 5
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS ....................................................................................................... 6
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS .................................................................................................... 8
3. 1.1 TFT LCD MODULE
3.1.2 Vcc Power Dip Condition
3.2 BACKLIGHT UNIT
4. BLOCK DIAGRAM ............................................................................................................................... 12
4.1 TFT LCD MODULE
4.2 BACKLIGHT UNIT
5. INPUT TERMINAL PIN ASSIGNMENT................................................................................................ 13
5.1 TFT LCD MODULE
5.2 LVD S DATA MAP P ING TABLE
5.3 BACKLIGHT UNIT
5.4 COLOR DATA INPUT ASSIGNMENT
6. INTERFACE TIMING ........................................................................................................................... 16
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE
7. OPTICAL CHARACTERISTICS........................................................................................................... 19
7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS
8. PACKAGING ........................................................................................................................................ 23
8.1 PACKING SPECIFICATIONS
8.2 PACKING METHOD
9. DEFINITION OF LABELS ................................................................................................................ ….25
10.RELIABILITY TEST ……………………………………………………………………………………….. 26
www.jxlcd.com
www.jxlcd.com
2 / 29
Version 2.0
Page 3
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
11. PRECAUTIONS …………………………………………………………………………………….. 27
11.1 ASSEMBLY AND HANDLING PRECAUTIONS
11.2 SAFETY PRECAUTIONS
11.3 SAFETY STANDARDS
11.4 STORAGE
11.5 OPERATION CONDITION GUIDE
11.6 OTHER
12. MECHANICAL CHARACTERISTICS ………………………………………………………….. 29
www.jxlcd.com
www.jxlcd.com
3 / 29
Version 2.0
Page 4
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
REVISION HISTORY
Version Date Section Description
Ver 2.0
17,Jun, 09’
www.jxlcd.com
www.jxlcd.com
-
M200O1 -L03 Approval specification was first issued.
4 / 29
Version 2.0
Page 5
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
M200O1-L03 is a 20.0” TFT Liquid Crystal Display module with 2 CCFL Backlight unit and 30 pins
2ch-LVDS interface. This module supports 1600 x 900 HD+ mode and can display up to 16.7M colors. The
inverter module for Backlight is not built in.
1.2 FEATURES
- Extra-wide viewing angle.
- High contrast ratio.
- Fast response time.
- High color saturation.
- HD+ (1600 x 900 pixels) resolution.
- DE (Data Enable) only mode.
- LVDS (Low Voltage Differential Signaling) interface.
- RoHS compliance.
- TCO03 compliance
1.3 APPLICATION
- TFT LCD Monitor
www.jxlcd.com
1.4 GENERAL SPECIFICATI0NS
Bezel Opening Area 446.8 (H) x 253.2 (V) mm
Transmissive Mode Normally White - -
Module Power Consumption 17.02 Watt (2)
www.jxlcd.com
Item Specification Unit Note
Active Area 442.8(H) x 249.075(V) (20.0” diagonal) mm
Driver Element a-Si TFT active matrix - -
Pixel Number 1600 x R.G.B. x 900 pixel -
Pixel Pitch 0.2768(H) x 0.2768 (V) mm -
Pixel Arrangement RGB vertical stripe - -
Display Colors 16.7M color -
Surface Treatment AG type, 3H hard coating, Haze 25 - -
(1)
1.5 MECHANICAL SPECIFICATIONS
Item Min. Typ. Max. Unit Note
Horizontal(H) 462.3 462.8 463.3 mm
Module Size
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
Note (2) Please refer to sec.3.1 & 3.2 for more information of power consumption
Vertical(V) 271.5 272.0 272.5 mm
Depth(D) 16.5 17 17.5 mm
Weight - 2300 2350 g -
5 / 29
(1)
Version 2.0
Page 6
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 60 ºC (1)
Operating Ambient Temperature TOP 0 50 ºC (1), (2)
Shock (Non-Operating) S
Vibration (Non-Operating) V
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max
- 50 G (3), (5)
NOP
- 1.5 G (4), (5)
NOP
Min. Max.
Value
Unit Note
Relative Humidity (%RH)
100
90
80
60
40
www.jxlcd.com
www.jxlcd.com
Note (3) 11ms, half sine wave, 1 time for ± X, ± Y, ± Z.
Note (4) 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
20
10
Temperature (ºC)
Operating Range
Storage Range
8060-20 40020-40
so that the module would not be twisted or bent by the fixture.
The fixing condition is shown as below:
6 / 29
Version 2.0
Page 7
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
Item Symbol
Power Supply Voltage Vcc -0.3 +6.0 V (1)
2.2.2 BACKLIGHT UNIT
Item Symbol
Lamp Voltage VL - 2.5K V Lamp Current IL 3.0 8.5 mA
Lamp Frequency FL 40 80 KHz
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
Min. Max.
Min. Max.
Value
Value
Unit Note
Unit Note
(1), (2)
RMS
RMS
(1), (2)
Note (2) Specified values are for lamp (Refer to 3.2 for further information).
www.jxlcd.com
www.jxlcd.com
7 / 29
Version 2.0
Page 8
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Power Supply Voltage Vcc 4.5 5.0 5.5 V -
Ripple Voltage VRP - - 200 mV -
Power on Rush Current I
Power Supply Current
RUSH
White 0.5 0.6 A (3)a Black 0.9 1.1 A (3)b
Vertical Stripe
3.0 A (2)
0.94 1.15 A (3)c
Power Consumption PLCD 4.7 5.75 Watt (4)
LVDS differential input voltage Vid 100 - 600 mV
LVDS common input voltage Vic 1.0 1.2 1.4 V
Note (1) The module should be always operated within above ranges.
Note (2) Power on rush current measurement conditions:
Value
Unit Note
+5.0V
R1
47K
Q1 2SK1475
FUSE
C3 1uF
Vcc
(LCD Module Input)
(High to Low)
(Control Signal)
SW
www.jxlcd.com
+12V
www.jxlcd.com
C1
1uF
VR1
R2
1K
47K
0.01uF
Q2
2SK1470
C2
Vcc rising time is 470µs
Vcc
0.9Vcc
0.1Vcc
GND
470µs
8 / 29
Version 2.0
Page 9
Doc No.: 400032801
≤≤≤
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, f
Hz, whereas a power dissipation check pattern below is displayed.
a. White Pattern
Active Area
c. Vertical Stripe Pattern
www.jxlcd.com
www.jxlcd.com
Active Area
b. Black Pattern
Active Area
R
G
R
B
G
R
B
G
R R
G
B B
B B
R R
R
G G
G G
B B
B B
R
R
= 60
v
Note (4)The power consumption is specified at the pattern with the maximum current
3.1.2 Vcc Power Dip Condition:
4.0V
4.5V
Vcc
Td
Dip condition:
msTdVVccV 20,5.40.4
9 / 29
Version 2.0
Page 10
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
3.2 BACKLIGHT UNIT
Parameter Symbol
Lamp Input Voltage VL 693 770 847 V
Lamp Current IL 3.0 8.0 8.5 mA
Lamp Turn On Voltage VS
Operating Frequency FL 40 55 80 KHz (3)
Lamp Life Time LBL 40,000 50,000 Hrs (5), IL = 8.0mA
Power Consumption PL 12.32 W (4), IL = 8.0mA
Note (1) Lamp current is measured by current amplify & oscilloscope as shown below:
www.jxlcd.com
Ta = 25 ± 2 ºC
www.jxlcd.com
HV (Red) LV (White)
HV (Blue)
LV (Black)
Current Probe
Min. Typ . Max.
1480(0 )℃ V 1230(25 ) V
1
2
1 2
Value
A
A
Measure equipment:
Current Amplify: Tektronix TCPA300 Current probe: Tektronix TCP312
Oscilloscope: TDS3054B
Ta = 25 ± 2 ºC
Unit Note
I
RMS
RMS
(2)
RMS
(2)
RMS
Current Amplify
= 8.0 mA
L
(1)
Oscilloscope
Note (2) The voltage that must be larger than Vs should be applied to the lamp for more than 1 second
after startup. Otherwise, the lamp may not be turned on normally. It is the value output voltage of
NF circuit.
Note (3) The lamp frequency may produce interference with horizontal synchronization frequency from the
display, which might cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronization frequency and its harmonics as
far as possible.
Note (4) P
Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition
(The effective ignition length is a scope that luminance is over 80% of that at the center point.)
Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the
= I
× VL × 2 (for 2lamps)
L
L
Ta = 25 ±2 (a) When the brightness becomes 50% of its original value. (b) When the effective ignition length becomes 80% of its original value.
inverter must have specifications for the modularized lamp. The performance of the Backlight,
such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for
o
C and IL = 8.0 mArms until one of the following events occurs:
10 / 29
Version 2.0
Page 11
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
much current leakage from high voltage output of the inverter. When designing or ordering the
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrument.
The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may
produce interface with horizontal synchronous frequency and as a result this may cause beat on the
display. Therefore lamp frequency shall be as away possible from the horizontal synchronous
frequency and from its harmonics in order to prevent interference.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its
leakage current.
a. The asymmetry rate of the inverter waveform should be 10% below;
b. The distortion rate of the waveform should be within 2 ± 10%;
c. The ideal sine wave form shall be symmetric in positive and negative polarities
* Asymmetry rate:
www.jxlcd.com
www.jxlcd.com
I p
I -p
| I
* Distortion rate
I
– I –p | / I
p
(or I –p) / I
p
rms
rms
* 100%
11 / 29
Version 2.0
Page 12
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
RXO0(+/-)
RXO1(+/-)
RXO2(+/-)
RXO3(+/-)
RXOC(+/-)
RXE0(+/-)
RXE1(+/-)
RXE2(+/-)
RXE3(+/-)
RXEC(+/-)
NC
Vcc
GND
VL
INPUT CONNECTOR
LAMP CONNECTOR
(YEONHO 35001HS-02L)
TIMING CONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
LVDS INPUT /
SCAN DRIVER IC
TFT LCD PANEL
(1600x3x900)
DA TA DRIVER IC
BACKLIGHT UNIT
4.2 BACKLIGHT UNIT
www.jxlcd.com
www.jxlcd.com
1 HV(Red)
2 LV(White)
1 HV(Blue)
2 LV(Black)
12 / 29
Version 2.0
Page 13
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE
Pin Name Description
1 RXO0- Negative LVDS differential data input. Channel O0 (odd) 2 RXO0+ Positive LVDS differential data input. Channel O0 (odd) 3 RXO1- Negative LVDS differential data input. Channel O1 (odd) 4 RXO1+ Positive LVDS differential data input. Channel O1 (odd) 5 RXO2- Negative LVDS differential data input. Channel O2 (odd) 6 RXO2+ Positive LVDS differential data input. Channel O2 (odd) 7 GND Ground 8 RXOC- Negative LVDS differential clock input. (odd) 9 RXOC+ Positive LVDS differential clock input. (odd)
10 RXO3- Negative LVDS differential data input. Channel O3(odd)
11 RXO3+ Positive LVDS differential data input. Channel O3 (odd) 12 RXE0- Negative LVDS differential data input. Channel E0 (even) 13 RXE0+ Positive LVDS differential data input. Channel E0 (even) 14 GND Ground 15 RXE1- Negative LVDS differential data input. Channel E1 (even) 16 RXE1+ Positive LVDS differential data input. Channel E1 (even) 17 GND Ground 18 RXE2- Negative LVDS differential data input. Channel E2 (even) 19 RXE2+ Positive LVDS differential data input. Channel E2 (even) 20 RXEC- Negative LVDS differential clock input. (even) 21 RXEC+ Positive LVDS differential clock input. (even) 22 RXE3- Negative LVDS differential data input. Channel E3 (even) 23 RXE3+ Positive LVDS differential data input. Channel E3 (even) 24 GND Ground 25 NC Not connection, this pin should be open. 26 NC Not connection, this pin should be open. 27 NC Not connection, this pin should be open. 28 Vcc +5.0V power supply 29 Vcc +5.0V power supply 30 Vcc +5.0V power supply
Note (1) Connector Part No.: STM MSAKT2407P30HA or Starconn 093G30-B0001A
www.jxlcd.com
www.jxlcd.com
Note (2) Mating Wire Cable Connector Part No.: FI-X30H(JAE) or FI-X30HL(JAE)
Note (3) Mating FFC Cable Connector Part No.: 217007-013001 (P-TWO) or JF05X030-1 (JAE)
Note (4) The first pixel is odd.
Note (5) Input signal of even and odd clock should be the same timing.
13 / 29
Version 2.0
Page 14
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
5.2 LVDS D ATA MAP P ING TABLE
LVDS Channel O0
LVDS Channel O1
LVDS Channel O2
LVDS Channel O3
LVDS Channel E0
LVDS Channel E1
LVDS Channel E2
LVDS Channel E3
LVDS output D7 D6 D4 D3 D2 D1 D0 Data order OG0 OR5 OR4 OR3 OR2 OR1 OR0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order OB1 OB0 OG5 OG4 OG3 OG2 OG1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA OB5 OB4 OB3 OB2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA OB7 OB6 OG7 OG6 OR7 OR6 LVDS output D7 D6 D4 D3 D2 D1 D0 Data order EG0 ER5 ER4 ER3 ER2 ER1 ER0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order EB1 EB0 EG5 EG4 EG3 EG2 EG1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA EB5 EB4 EB3 EB2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA EB7 EB6 EG7 EG6 ER7 ER6
5.3 BACKLIGHT UNIT:
Pin Symbol Description Remark
1 HV High Voltage Red 2 LV Low Voltage White 1 HV High Voltage Blue 2 LV Low Voltage Black
Note (1) Connector Part No.: YEONHO 35001HS-02L or equivalent
www.jxlcd.com
www.jxlcd.com
14 / 29
Version 2.0
Page 15
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
5.4 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for
the color. The higher the binary input, the brighter the color. The table below provides the assignment of
color versus data input.
Data Signal
Basic
Colors
Gray
Scale
Of
Red
Color
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
Red(0) / Dark
Red(1) Red(2)
Red(253) Red(254) Red(255)
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
:
:
:
:
:
:
1
1
1
1
1
1
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0 0 0 1 1 1 0 1 0 0 0
0 0 0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(0) / Dark
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Voltage, 1: High Level Voltage
Green(1) Green(2)
www.jxlcd.com
www.jxlcd.com
Green(253) Green(254) Green(255)
Blue(0) / Dark
Blue(1) Blue(2)
Blue(253) Blue(254) Blue(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
15 / 29
Version 2.0
Page 16
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency Fc 48.3 59.2 75.7 MHz ­Period Tc - 16.89 - ns Input cycle to cycle jitter Spread spectrum
LVDS Clock
LVDS Da t a
Vertical Active Display Term
Horizontal Active Display Term
Note: Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored.
www.jxlcd.com
www.jxlcd.com
modulation range Spread spectrum modulation frequency High Time Tch - 4/7 - Tc ­Low Time Tcl - 3/7 - Tc ­Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame Rate Fr 50 60 75 Hz Tv=Tvd+Tvb Total Tv 929 934 942 Th ­Display Tvd 900 900 900 Th ­Blank Tvb Tv-Tvd Tv-Tvd Tv-Tvd Th ­Total Th 1040 1056 1072 Tc Th=Thd+Thb Display Thd 800 800 800 Tc ­Blank Thb
T
- - +2%Tc ps (1)
rcl
clkin_mod
F
F
SSM
-2%Fc - +2%Fc MHz
- - 200 KHz
Th-Thd Th-Thd Th-Thd
Tc -
(2)
(3)
INPUT SIGNAL TIMING DIAGRAM
DE
Th
DCLK
C
T
DE
DATA
Thb
T
hd
16 / 29
Version 2.0
Page 17
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
Note (1) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T1 – TI
T1
Note (2) The SSCG (Spread spectrum clock generator) is defined as below figures.
www.jxlcd.com
www.jxlcd.com
Note (3) The LVDS timing diagram and setup/hold time is defined and showing as the following figures.
LVDS RECEIVER INTERFACE TIMING DIAGRAM
RXCLK+/-
RXn+/-
Tlvs
Tlvh
Tc
1
14
T
c
3
T
c
14
5
T
c
14
7
T
c
14
17 / 29
9
14
T
c
11
14
T
13
c
T
c
14
Version 2.0
Page 18
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
6.2 POWER ON/OFF SEQUENCE
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the
diagram below.
- Power Supply
for LCD, Vcc
- Interface Signal
(LVDS Signal of Transmitter), V
- Power for Lamp
Timing Specifications:
0.5< t1 10 msec 0 < t2 ≦ 50 msec 0 < t3 ≦ 50 msec
90%
0V
0V
I
t4 500 msec
www.jxlcd.com
www.jxlcd.com
t5 450 msec
10%
t1
Valid Data
ON OFF OFF
90%
t6 t5
50% 50%
t4
10%
t7
t3 t2
10%
t6 90 msec
5t7 100 msec
Note.
(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.
(2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation of the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
(3) In case of VCC = off level, please keep the level of input signals on the low or keep a high impedance.
(4) T4 should be measured after the module has been fully discharged between power off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
(6)
CMO won’t take any responsibility for the products which are damaged by the customers not following the
Power Sequence.
(7)
There might be slight electronic noise when LCD is turned off (even backlight unit is also off). To avoid this
symptom, we suggest "Vcc falling timing" to follow "t7 spec".
18 / 29
Version 2.0
Page 19
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta 25±2
Ambient Humidity Ha 50±10 %RH
Supply Voltage VCC 5V V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Lamp Current IL 8.0±0.5 mA
Inverter Operating Frequency FL 55±5 KHz
Inverter CMO 27-D026337(Logah MIT70070.50)
7.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown in 7.2. The following items should
o
C
be measured under the test conditions described in 7.1 and stable environment shown in Note (5).
Item Symbol Condition Min. Typ. Max. Unit Note
Red
Color
Chromaticity
(CIE 1931)
www.jxlcd.com
www.jxlcd.com
Center Luminance of White
(Center of Screen)
Contrast Ratio CR
Response Time
White Variation δW
Viewing Angle
Viewing Angle
Green
Blue
White
Horizontal
Vertica l
Horizontal
Vertica l
Rx
Ry
Gx Gy Bx
By
Wx
Wy
L
C
TR - 1.5 2.5
TF - 3.5 5.5
To ta l
T
θ
+ 75 85 -
x
θ
- 75 85 -
x
θ
+ 70 80 -
Y
θ
-
Y
θ
+
x
θ
-
x
θ
+
Y
-
θ
Y
=0°, θY =0°
θ
x
CS-1000T
θ
=0°, θY =0°
x
θ
=0°, θY =0°
x
USB2000
CR 10
USB2000
CR5
USB2000
Typ -
0.03
200 250 - - (4), (5)
700 1000 - - (2), (5)
70 80 -
80 80 75 75
0.650
0.335
0.283
0.604
0.152
0.070
0.313
0.329
5 8
- - 1.33 - (5), (6)
89 ­89 85
85
Typ +
0.03
-
-
-
- (1), (5)
ms (3)
Deg. (1), (5)
Deg. (1), (5)
19 / 29
Version 2.0
Page 20
Doc No.: 400032801
y
y
+
y
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
Note (1) Definition of Viewing Angle (θx, θy):
Normal
θX- = 90º
6 o’clock
- = 90º
θ
Note (2) Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
www.jxlcd.com
www.jxlcd.com
CR = CR (5)
x-
y-
θx = θ
θy- θy+
= 0º
θx
θx
12 o’clock direction
y+
+ = 90º
θ
x+
θX+ = 90º
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (3) Definition of Response Time (T
100%
90%
Optical
Response
10%
0%
Gray Level 255
, TF):
R
Gray Level 255
Gray Level 0
T
T
R
66.67ms 66.67ms
F
20 / 29
Version 2.0
Page 21
Doc No.: 400032801
500
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
Note (4) Definition of Luminance of White (L
Measure the luminance of gray level 255 at center point
LC = L (5)
L (x) is corresponding to the luminance of the point X at Figure in Note (6).
Note (5) Measurement Setup:
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 30 minutes in a windless room.
LCD Module
LCD Panel
USB2000
Center of the Screen
www.jxlcd.com
www.jxlcd.com
mm
):
C
CS-1000T
Light Shield Room (Ambient Luminance < 2 lux)
21 / 29
Version 2.0
Page 22
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
Note (6) Definition of White Variation (δW):
Measure the luminance of gray level 255 at 9 points
δW = Maximum [L (1), L (2) ……L (8), L (9)] / Minimum [L (1), L (2) …… L (8), L (9)]
Horizontal Line
D
W
Vertical Line
www.jxlcd.com
www.jxlcd.com
W/10
W/2
9W/10
D/10
1
4
7 8 9
D/2
2
5
Active Area
9D/10
3
6
X
: Test Point
X=1 to 9
22 / 29
Version 2.0
Page 23
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
8. PACKAGING
8.1 PACKING SPECIFICATIONS
(1) 10 LCD modules / 1 Box
(2) Box dimensions: 540(L) X 380 (W) X 355 (H) mm
(3) Weight: 22.7 Kg (10 modules per box)
8.2 PACKING METHOD
(1) Carton Packing should have no failure in the following reliability test items.
Test Item Test Conditions Note
ISTA STANDARD Random, Frequency Range: 1 – 200 Hz
Vibration
Dropping Test 1 Corner, 3 Edge, 6 Face, 45.7cm Non Operation
Top & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X) Back & Forth 10 minutes (Y)
Non Operation
For ocean shipping
www.jxlcd.com
www.jxlcd.com
Figure. 8-1 Packing method
23 / 29
Version 2.0
Page 24
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
For air transport
Corner Protector (50*50*1000mm)
PE Sheet
Film
Figure. 8-2 Packing method
www.jxlcd.com
www.jxlcd.com
Air Transportation
PP Belt
Corner Protector
(50*50*1250mm)
Pallet (1150*1080*143mm)
Carton label
Figure. 8-3 Packing method
24 / 29
Version 2.0
Page 25
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
9. DEFINITION OF LABELS
9.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.
(a) Model Name: M200O1-L03
(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.
(c) CMO barcode definition:
Serial ID: XX
Code Meaning Description
XX CMO internal use -
XX Revision Cover all the change
X CMO internal use -
XX CMO internal use -
YMD Year, month, day
www.jxlcd.com
www.jxlcd.com
L Product line # Line 1=1, Line 2=2, Line 3=3, …
NNNN Serial number Manufacturing sequence of product
(d) Customer’s barcode definition:
Serial ID: CM
Code Meaning Description
CM Supplier code CMO=CM
20O12 Model number M200O1-L03= 20O13
X Revision code Non ZBD: 1,2,~,8,9 / ZBD: A~Z
X Source driver IC code
X Gate driver IC code
-XX-X-XX-YMD-L-NNNN
Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C Day: 1~31=1, 2, 3, ~, 9, A, B, C, ~, W, X, Y, exclude I, O, and U.
-20O13-X-X-X-XX-L-XX-L-YMD-NNNN
Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6, Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C, OKI=D, Philips=E, Renasas=F, Samsung=G, Sanyo=H, Sharp=I, TI=J, Topro=K, Toshiba=L, Windbond=M
XX Cell location Tainan Taiwan=TN, Ningbo China=CN
L Cell line #
XX Module location
L Module line #
YMD Year, month, day
NNNN Serial number By LCD supplier
1,2,~,9,A,B,~,Y,Z
Tainan, Taiwan=TN ; Ningbo China=NP
1,2,~,9,A,B,~,Y,Z
Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C Day: 1~31=1, 2, 3, ~, 9, A, B, C, ~, T, U, V
25 / 29
Version 2.0
Page 26
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
(e) FAB ID(UL Factory ID):
Region Factory ID
TWCMO GEMN
NBCMO LEOO
NBCME CANO
NHCMO CAPG
10. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition Note
Temperature Humidity Bias (THB)
High Temperature Operation (HTO)
Low Temperature Operation (LTO)
High Temperature Storage (HTS)
Low Temperature Storage (LTS)
Vibration Test (Non-operation)
Shock Test (Non-operation)
Thermal Shock Test (TST)
On/Off Test
www.jxlcd.com
www.jxlcd.com
Ta= 5 0 , 80%RH, 240hours Ta= 5 0 ℃ , 50%RH , 240hours Ta= 0 , 240hours Ta= 6 0 , 240hours Ta= - 2 0 , 240hours
Acceleration: 1.5 Grms Wave: Half-sine Frequency: 10 - 300 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G Wave: Half-sine Active Time: 11 ms
Direction : ± X, ± Y, ± Z.(one time for each Axis)
-20/30min , 60 / 30min , 100 cycles 25 ,On/10sec , Off /10sec , 30,000 cycles
ESD (Electro Static Discharge)
Altitude Test
Contact Discharge: ± 8KV, 150pF(330) Air Discharge: ± 15KV, 150pF(330)
Operation:10,000 ft / 24hours Non-Operation:30,000 ft / 24hours
26 / 29
Version 2.0
Page 27
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
11. PRECAUTIONS
11.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil
may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will
be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage
LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD module within
the specified storage conditions.
(10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
response time will become slowly, and the starting voltage of CCFL will be higher than room
temperature.
www.jxlcd.com
www.jxlcd.com
11.2 SAFETY PRECAUTIONS
(1) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while
assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit.
(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(3) After the module’s end of life, it is not harmful in case of normal operation and storage.
11.3 SAFETY STANDARDS
The LCD module should be certified with safety regulations as follows:
(1) UL60950-1 or updated standard.
(2) IEC60950-1 or updated standard.
11.4. Storage
(1) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0 to 35
And relative humidity of less than 70%
(2) Do not store the TFT – LCD module in direct sunlight
(3) The module should be stored in dark place. It is prohibited to apply sunlight or fluorescent light in storing
27 / 29
Version 2.0
Page 28
Doc No.: 400032801
Issued Date:.17,Jun,2009
Model No.: M200O1-L03
Approval
11.5. Operation condition guide
(1) The LCD product should be operated under normal condition.
Normal condition is defined as below :
Temperature : 20±15
Humidity: 65±20%
Display pattern : continually changing pattern(Not stationary)
(2) If the product will be used in extreme conditions such as high temperature , high humidity , high altitude ,
display pattern or operation time etc…It is strongly recommended to contact CMO for application
engineering advice . Otherwise , Its reliability and function may not be guaranteed.
11.6 OTHER
When fixed patterns are displayed for a long time, remnant image is likely to occur.
www.jxlcd.com
www.jxlcd.com
28 / 29
Version 2.0
Page 29
www.jxlcd.com
www.jxlcd.com
Loading...