Page 1
Doc. No.: 44086418
A
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
TFT LCD Approval Specification
MODEL NO.: M190A1-L0C
Customer: Nexgen
pproved by:
Note:
www.jxlcd.com
www.jxlcd.com
記錄 工作 審核 角色 投票
2008-10-14
10:44:48 CST
PMMD II
Director
kevin_wu(吳柏勳
/56520/54894)
1 / 25
Director Accept
Version 3.1
Page 2
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
- CONTENTS -
REVISION HISTORY
1. GENERAL DESCRIPTION
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATI NGS OF ENVIRONMENT
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
2.2.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
3.2 Vcc POWER DIP CONDITION
3.3 BACKLIGHT UNIT
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
4.2 BACKLIGHT UNIT
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE
5.2 LVDS DATA MAPPING TABLE
5.3 BACKLIGHT UNIT
5.4 COLOR DATA INPUT ASSIGNMENT
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS
8. PACKAGING
8.1 PACKING SPECIFICATIONS
8.2 PACKING METHOD
9. DEFINITION OF LABELS
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
10.2 SAFETY PRECAUTIONS
11. MECHANICAL CHARACTERISTICS
www.jxlcd.com
www.jxlcd.com
2 / 25
Version 3.1
Page 3
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
REVISION HISTORY
Date Section Description
All
7.2
Jun. 09, 08’
Jul. 04, 08’
www.jxlcd.com
www.jxlcd.com
3.0
3.1
M190A1-L0C Specifications was first issued.
Bx value changes from 0.0152 to 0.152.
3 / 25
Version 3.1
Page 4
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
M190A1-L0C is a 19” wide TFT Liquid Crystal Display module with 4 CCFL Backlight unit and 30 pins
2ch-LVDS interface. This module supports 1440 x 900 WXGA+ mode and can display 16.7M colors. The
inverter module for Backlight is not built in.
1.2 FEATURES
- Super Wide viewing angle.
- Super High contrast ratio
- Super fast response time
- High color saturation
- WXGA+ (1440 x 900 pixels) resolution
- DE (Data Enable) only mode
- LVDS (Low Voltage Differential Signaling) interface
- RoHS Compliance
1.3 APPLICA TION
- TFT LCD Monitor
1.4 GENERAL SPECIFICATI0NS
Item Specification Unit Note
www.jxlcd.com
Diagonal Size 481.4 (18.95” diagonal) mm
Active Area 408.24 (H) x 255.15 (V) mm
Bezel Opening Area 412.24 (H) x 259.15 (V) mm
Driver Element a-si TFT active matrix - Pixel Number 1440 x R.G.B. x 900 pixel Pixel Pitch 0.2835 (H) x 0.2835 (V) mm Pixel Arrange ment RGB vertical stripe - Display Colors 16.7M color Transmissive Mode Normally White - Color Saturation 92%NTSC (typ.)
Surface Treatment Hard coating (3H), Anti-glare (Haze 25) - -
1.5 MECHANICAL SPECIFICATIONS
Module Size
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
www.jxlcd.com
Item Min. Typ. Max. Unit Note
Horizontal(H) 427.5 428 428.5 mm
Vertical(V) 277.5 278 278.5 mm
Depth(D) - 17.1 17.6 mm
Weight - 1835 1880 g -
(1)
(1)
4 / 25
Version 3.1
Page 5
Doc. No.: 44086418
A
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Symbol
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient T emperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) S
Vibration (Non-Operating) V
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta ≦ 40 ºC).
- 50 G (3), (5)
NOP
- 1.5 G (4), (5)
NOP
Min. Max.
Value
Unit Note
www.jxlcd.com
www.jxlcd.com
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.
Note (3) 50G/11ms, half sine wave, 1 time for ± X, ± Y, ± Z.
Note (4) 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
t Room Temperature
Side Mount Fixing Screw
LCD Module
Side Mount Fixing Screw
Stage
Gap=2mm
Bracket
5 / 25
Version 3.1
Page 6
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
2.2 ELECTRICAL ABSOLUTE RATINGS
2.2.1 TFT LCD MODULE
Item Symbol
Power Supply Voltage Vcc -0.3 +6.0 V (1)
2.2.2 BACKLIGHT UNIT
Item Symbol
Lamp Voltage VL - 2.0K V
Lamp Current IL - 10.0 mA
Lamp Frequency FL - 80 KHz
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Co nditions.
Note (2) Specified values are for lamp (Refer to 3.3 for further information).
Min. Max.
Min. Max.
Value
Value
Unit Note
Unit Note
(1), (2), IL = 7.0mA
RMS
RMS
(1), (2)
www.jxlcd.com
www.jxlcd.com
6 / 25
Version 3.1
Page 7
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Parameter Symbol
Min. Typ. Max.
Power Supply V oltage Vcc 4.5 5.0 5.5 V Ripple Voltage VRP - - 100 mV Rush Current I
White - 0.45 0.55 A (3)a
Power Supply Current
Black - 0.67 0.80 A (3)b
Vertical Stripe
-
RUSH
lcc
- 0.65 0.78 A (3)c
LVDS differential input voltage Vid 100 - 600 mV
LVDS common input voltage Vic - 1.2 - V
Note (1) The module should be always operated within above ranges.
Note (2) Measurement Conditions:
Value
-
Unit Note
3 A (2)
+5.0V
R1
47K
Q1 2SK1475
FUSE
C3
1uF
Vcc
(LCD Module Input)
(High to Low)
(Control Signal)
SW
www.jxlcd.com
www.jxlcd.com
+12V
C1
1uF
VR1
R2
1K
47K
0.01uF
Q2
2SK1470
C2
Vcc rising time is 470µs
Vcc
0.9Vcc
0.1Vcc
GND
470µs
7 / 25
Version 3.1
Page 8
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, fv = 60
Hz, whereas a power dissipation check pattern below is displayed.
a. White Pattern
Active Area
c. Vertical Stripe Pattern
b. Black Pattern
Active Area
R
G
R
B
G
R
B
G
R R
G
B
B
B
B
R
R
R
G
G
G
G
B
B
B
B
R
R
www.jxlcd.com
3.2 Vcc POWER DIP CONDITION:
Dip condition:
www.jxlcd.com
Active Area
Td
Vcc
4.5V
4.0V
msTdVVccV 20,5.40.4 ≤≤≤
8 / 25
Version 3.1
Page 9
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
3.3 BACKLIGHT UNIT
Parameter Symbol
Lamp Input Voltage VL --- 750 825 V
Lamp Current IL 3.0 7.0 8.0 mA
Lamp Turn On Voltage VS
Operating Frequency FL 40 --- 80 KHz (3)
Lamp Life Time LBL 40000 --- --- Hrs (5)
Power Consumption PL --- 21.0 --- W (4), IL = 7.0 mA
Note (1) Lamp current is measured by utilizing high frequency current meters as shown below:
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup.
LCD
HV (Pink)
LV (White)
HV (Blue)
LV (Black)
Min. Typ. Max.
--- ---
--- ---
1
2
1
2
Value
1220(25℃)
1620(0℃)
A
Inverter
A
Ta = 25 ± 2 ºC
Unit Note
I
RMS
RMS
V
(2)
RMS
V
(2)
RMS
Current Meter
YOKOGAWA 2016
= 7.0 mA
L
(1)
A
Otherwise the lamp may not be turned on.
Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
www.jxlcd.com
www.jxlcd.com
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.
Note (4) P
Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition
Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the
= IL ×VL × 4 CCFLs
L
Ta = 25 ±2
(a) When the brightness becomes or lower than 50% of its original value.
(b) When the effective ignition length becomes ≦ 80% of its origin al value.
(The effective ignition length is a scope that luminance is over 70% of that at the center point.)
inverter must have specifications for the modularized lamp. The performance of the Backlight,
such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for
the lamp. All the parameters of an inverter should be carefully designed to avoid producing too
much current leakage from high voltage output of the inverter. When designing or ordering the
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
o
C and IL = 7.0 mA rms until one of the following events occurs:
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrume nt.
9 / 25
Version 3.1
Page 10
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may
produce interface with horizontal synchronous frequency and as a result this may cause beat on the
display. Therefore lamp frequency shall be as away possible from the horizontal synchronous
frequency and from its harmonics in order to prevent interference.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its
leakage current.
a. The asymmetry rate of the inverter waveform should be 10% below;
b. The distortion rate of the waveform should be within √2 ± 10%;
c. The ideal sine wave form shall be symmetric in positive and negative polarities.
* Asymmetry rate:
I p
I -p
www.jxlcd.com
www.jxlcd.com
| I
* Distortion rate
I
– I –p | / I
p
(or I –p) / I
p
rms
rms
* 100%
10 / 25
Version 3.1
Page 11
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
RXO0(+/-)
RXO1(+/-)
RXO2(+/-)
RXO3(+/-)
RXOC(+/-)
RXE0(+/-)
RXE1(+/-)
RXE2(+/-)
RXE3(+/-)
RXEC(+/-)
NC
Vcc
GND
VL
(JAE- FI-X30SSL-HF or
INPUT CONNECTOR
-
LAMP CONNECTOR
(YEONHO 35001HS-02L )
LVDS INPUT /
TIMING CONTROLLER
DC/DC CONVERTER &
REFERENCE VOLTAGE
SCAN DRIVER IC
TFT LCD PANEL
(1440x3x900)
DA TA DRIVER IC
BACKLIGHT UNIT
4.2 BACKLIGHT UNIT
www.jxlcd.com
www.jxlcd.com
1 HV(Pink)
2 LV(White)
1 HV(Blue)
2 LV(Black)
1 HV(Pink)
2 LV(White)
1 HV(Blue)
2 LV(Black)
Note: On the same side, the same-polarity lamp voltage design for lamps is recommended.
11 / 25
Version 3.1
Page 12
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
5. INPUT TERMINAL PIN ASSIGNMENT
5.1 TFT LCD MODULE
Pin Name Description
1 RXO0- Negative LVDS diff erential data input. Channel O0 (odd)
2 RXO0+ Positive LVDS differential data input. Channel O0 (odd)
3 RXO1- Negative LVDS diff erential data input. Channel O1 (odd)
4 RXO1+ Positive LVDS differential data input. Channel O1 (odd)
5 RXO2- Negative LVDS diff erential data input. Channel O2 (odd)
6 RXO2+ Positive LVDS differential data input. Channel O2 (odd)
7 GND Ground
8 RXOC- Negative LVDS differential clock input. (odd)
9 RXOC+ Positive LVDS differential clock input. (odd)
10 RXO3- Negative LVDS differential data input. Channel O3(odd)
11 RXO3+ Positive LVDS differential data input. Channel O3 (odd)
12 RXE0- Negative LVDS diff erential data input. Channel E0 (even)
13 RXE0+ Positive LVDS differential data input. Channel E0 (even)
14 GND Ground
15 RXE1- Negative LVDS diff erential data input. Channel E1 (even)
16 RXE1+ Positive LVDS differential data input. Channel E1 (even)
17 GND Ground
18 RXE2- Negative LVDS diff erential data input. Channel E2 (even)
19 RXE2+ Positive LVDS differential data input. Channel E2 (even)
20 RXEC- Negative LVDS differential clock input. (even)
21 RXEC+ Positive L V DS differential clock input. (even)
22 RXE3- Negative LVDS diff erential data input. Channel E3 (even)
23 RXE3+ Positive LVDS differential data input. Channel E3 (even)
24 GND Ground
25 NC Not connection, this pin should be open.
26 NC Not connection, this pin should be open.
27 NC Not connection, this pin should be open.
28 Vcc +5.0V power supply
29 Vcc +5.0V power supply
30 Vcc +5.0V power supply
Note (1) Connector Part No.: JAE- FI-X30SSL-HF or STM MSAKT2407P30A.
www.jxlcd.com
www.jxlcd.com
Note (2) The first pixel is odd.
Note (3) Input signal of even and odd clock should be the same timing.
12 / 25
Version 3.1
Page 13
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
5.2 LVDS DATA MAPPING TABLE
L VDS Channel O0
L VDS Channel O1
L VDS Channel O2
L VDS Channel O3
L VDS Channel E0
L VDS Channel E1
L VDS Channel E2
L VDS Channel E3
LVDS output D7 D6 D4 D3 D2 D1 D0
Data order OG0 OR5 OR4 OR3 OR2 OR1 OR0
LVDS output D18 D15 D14 D13 D12 D9 D8
Data order OB1 OB0 OG5 OG4 OG3 OG2 OG1
LVDS output D26 D25 D24 D22 D21 D20 D19
Data order DE NA NA OB5 OB4 OB3 OB2
LVDS output D23 D17 D16 D11 D10 D5 D27
Data order NA OB7 OB6 OG7 OG6 OR7 OR6
LVDS output D7 D6 D4 D3 D2 D1 D0
Data order EG0 ER5 ER4 ER3 ER2 ER1 ER0
LVDS output D18 D15 D14 D13 D12 D9 D8
Data order EB1 EB0 EG5 EG4 EG3 EG2 EG1
LVDS output D26 D25 D24 D22 D21 D20 D19
Data order DE NA NA EB5 EB4 EB3 EB2
LVDS output D23 D17 D16 D11 D10 D5 D27
Data order NA EB7 EB6 EG7 EG6 ER7 ER6
www.jxlcd.com
www.jxlcd.com
13 / 25
Version 3.1
Page 14
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
5.3 BACKLIGHT UNIT
Pin Symbol Description Remark
1 HV High Voltage Pink
2 LV Low Voltage White
1 HV High Voltage Blue
2 LV Low Voltage Black
Note (1) Connector Part No.: YEONHO 35001 HS-02L or equivalent
Note (2) User’s connector Part No.: YEONHO 35001 WR-02L or equivalent
5.4 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for
the color. The higher the binary input, the brighter the color. The table below provides the assignment of
color versus data input.
Data Signal
Basic
Colors
Gray
Scale
Of
Red
Color
R7 R6 R5 R4 R3 R2 R1 R0 R7 R6 G5 G4 G3 G2 G1 G0 R7 R6 B5 B4 B3 B2 B1 B0
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
Red(0) / Dark
Red(1)
www.jxlcd.com
www.jxlcd.com
Red(2)
:
:
Red(253)
Red(254)
Red(255)
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
:
:
:
:
1
1
1
1
1
1
Red Green Blue
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green(0) / Dark
Gray
Scale
Of
Green
Gray
Scale
Of
Blue
Note (1) 0: Low Level Volt age, 1: High Level Voltage
Green(1)
Green(2)
:
:
Green(253)
Green(254)
Green(255)
Blue(0) / Dark
Blue(1)
Blue(2)
:
:
Blue(253)
Blue(254)
Blue(255)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
14 / 25
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Version 3.1
Page 15
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency Fc 40 44.5 61 MHz -
LVDS Clock
LVDS Data
Vertical Active Display Term
Horizontal Active Display Term
Period Tc 16.4 22.5 28.6 ns
High Time Tch - 4/7 - Tc Low Time Tcl - 3/7 - Tc Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame Rate Fr 47 60 75 Hz Tv=Tvd+Tvb
Total Tv 905 926 1200 Th Display Tvd 900 900 900 Th Blank Tvb Tv-Tvd 26 Tv-Tvd Th Total Th 770 800 960 Tc Th=Thd+Thb
Display Thd 720 720 720 Tc Blank Thb Th-Thd 80 Th-Thd Tc -
Note: Because this module is operated by DE only mode, Hsync and Vsync input signals should be set
to low logic level or ground. Otherwise, this module would operate abnormally.
INPUT SIGNAL TIMING DIAGRAM
www.jxlcd.com
www.jxlcd.com
DE
Th
DCLK
C
DE
DATA
T
Thb
T
hd
15 / 25
Version 3.1
Page 16
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
6.2 POWER ON/OFF SEQUENCE
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the
diagram below.
10%
Restart
10%
t4
Power Supply
for LCD, Vcc
- Interface Signal
(LVDS Signal of
Transmitter), V
Power On
90%
0V
0V
I
10%
t1
t2
Valid Data
Power Off
90%
t3
t6 t5
- Power for Lamp
Timing Specifications:
0.5< t1 ≦ 10 msec
0 < t2 ≦ 50 msec
0 < t3 ≦ 50 msec
www.jxlcd.com
www.jxlcd.com
t4 ≧ 500 msec
t5 ≧ 450 msec
t6 ≧ 90 msec
Note.
(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.
(2) Apply the lamp volt age within the LCD operation range. When the backlight turns on before the LCD
operation of the LCD turns off before the backlight turns off, the display may momentarily become abnormal
ONOFF OFF
50%50%
screen.
(3) In case of Vcc = off level, please keep the level of input signals on the low or keep a high impedance.
(4) T4 should be measured after the module has been fully discharged between power off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
16 / 25
Version 3.1
Page 17
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Supply Volt age VCC 5.0 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Lamp Current IL 7.0 mA
Inverter Operating Frequency FL 55 KHz
Inverter Darfon VK.13165.101
25±2
50±10
7.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown in 7.2. The following items should
be measured under the test conditions described in 7.1 and stable environment shown in Note (5).
Item Symbol Condition Min. Typ. Max. Unit Note
Red
Color
Chromaticity
Center Luminance of White L
Contrast Ratio CR
Response Time
White Variation
Viewing Angle
www.jxlcd.com
www.jxlcd.com
Green
Blue
White
Horizontal
Vertical
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
TR --- 1.5 6.5 ms
T
δW θ
θ
θ
θ
θ
Typ –
=0°, θY =0°
θ
x
CS-1000T
C
=0°, θY =0°
θ
F
+
x
-
x
+
Y
-
Y
x
=0°, θY =0°
x
CR ≧ 10
0.035
220 280 --- cd/m2(4), (5)
630 1000 --- - (2), (5)
--- 3.5 8.5 ms
--75 85 ---
75
70
70
0.669
0.319
0.197
0.684
0.152
0.079
0.321
0.329
1.3 1.5
85 --80 --80 ---
Typ +
0.035
o
C
%RH
(1), (5)
(3)
- (5), (6)
Deg. (1), (5)
17 / 25
Version 3.1
Page 18
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
Note (1) Definition of Viewing Angle (θx, θy):
Note (2) Definition of Contrast Ratio (CR):
θX- = 90º
6
o’clock
The contrast ratio can be calculated by the following expression.
x-
y-
Normal
θx = θy = 0º
θy- θy+
θx−
θx+
y+
12 o’clock direction
θ
y+ = 90º
x+
θX+ = 90º
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
www.jxlcd.com
www.jxlcd.com
L 0: Luminance of gray level 0
CR = CR (1)
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (3) Definition of Response Time (T
100%
90%
Optical
Response
10%
0%
Gray Level 255
R
T
R
, TF):
Gray Level 0
Gray Level 255
Time
T
F
66.67ms
66.67m
18 / 25
Version 3.1
Page 19
Doc. No.: 44086418
A
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
Note (4) Definition of Luminance of White (LC):
Measure the luminance of gray level 255 at center point
LC = L (1)
L (x) is corresponding to the luminance of the point X at Figure in Note (6).
Note (5) Measurement Setup:
The LCD module should be stabilized at given temperature for 40 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 40 minutes in a windless room.
www.jxlcd.com
Note (6) Definition of White Variation (δW):
www.jxlcd.com
LCD Module
LCD Panel
Center of the Screen
Photometer
(CS-1000T, USB-2000)
=
º
Light Shield Room
(Ambient Luminance < 2
Measure the luminance of gray level 255 at 9 points
δW = Maximum [L (1), L (2) ……L (4), L (9)] / Minimum [L (1), L (2) …… L (4), L (9)]
W
W/10
W/2
9W/10
Vertical Line
D/10
1
4
7 8 9
Horizontal Line
D
D/2
2
5
Active Area
9D/10
3
6
X
: Test Point
X=1 to 9
19 / 25
ctive area
Version 3.1
Page 20
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
8. PACKAGING
8.1 PACKIN G SPECIFICATIONS
(1) 7 LCD modules / 1 Box
(2) Box dimensions: 525(L) X 300 (W) X 360 (H) mm
(3) Weight: approximately 15.19 Kg (7 modules per box)
8.2 PACKING METHOD
(1) Carton Packing should have no failure in the following reliability test items.
Test Item Test Conditions Note
ISTA STANDARD
Random, Frequency Range: 1 – 200 Hz
Vibration
Dropping Test 1 Corner, 3 Edge, 6 Face, 61cm Non Operation
www.jxlcd.com
Top & Bottom: 30 minutes (+Z), 10 min (-Z),
Right & Left: 10 minutes (X)
Back & Forth 10 minutes (Y)
www.jxlcd.com
Non Operation
Figure. 8-1 Packing method
20 / 25
Version 3.1
Page 21
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
For ocean shipping
Sea / Land Transportation (40ft HQ Container)
PP Belt
Carton label
Film
Film
PE Sheet
PE Sheet
Corner Protector
(50*50*1000mm)
Corner Protector
(50*50*1000mm)
Corner Protector
(50*50*1000mm)
Pallet
(1150*1150*143mm)
Sea / Land Transportation (40ft Container)
PP Belt
Carton label
Corner Protector
(50*50*625mm)
Corner Protector
(50*50*1000mm)
Pallet
(1150*1150*143mm)
Film
Film
PE Sheet
PE Sheet
Corner Protector
(50*50*1000mm)
Figure. 8-2 Packing method
For air transport
Corner Protector
(50*50*1000mm)
PE Sheet
Film
www.jxlcd.com
www.jxlcd.com
Air Transportation
PP Belt
Corner Protector
(50*50*1000mm)
Pallet
(1150*1150*143mm)
Carton label
Figure. 8-3 Packing method
21 / 25
Version 3.1
Page 22
Doc. No.: 44086418
X
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
9. DEFINITION OF LABELS
9.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.
M190A1-L0C Rev. X
(Fab ID)
RoHS
XXXXXXXYMDLNNNN
CM19A1CXXXXXLXXLYM DNNNN
(a) Model Name: M190A1-L0C
(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc .
(c) CMO barcode definition:
Serial ID: XX
Code Meaning Description
XX CMO internal use XX Revision Cover all the change
X CMO internal use -
YMD
L Product line # Line 1=1, Lin e 2=2, Line 3=3, …
NNNN Serial number Manufacturing sequence of product
www.jxlcd.com
(d) Customer’s barcode definition:
www.jxlcd.com
-XX-X-XX-YMD-L-NNNN
Year, month, day Year: 2001=1, 2002=2, 2003=3, 2004=4…
Month: 1~12=1, 2, 3, ~, 9, A, B, C
Day: 1~31=1, 2, 3, ~, 9, A, B, C, ~, W, X, Y, exclude I, O, and U.
Serial ID: CM
Code Meaning Description
CM Supplier code CMO=CM
19A1C Model number M190A1-L0C=19A1C
X Revision code Non ZBD: 1,2,~,8,9 / ZBD: A~Z
X Source driver IC code
X Gate driver IC code
XX Cell location Tainan, Taiwan=TN
L Cell line # 1,2,~,9,A,B,~,Y,Z
XX Module location Tainan, Taiwan=TN ; Ningbo China=NP
L Module line # 1,2,~,9,A,B,~,Y,Z
YMD
NNNN Serial number Manufacturing sequence of product
(e) UL Factory ID:
Region Factory ID
TWCMO GEMN
NBCMO LEOO
NBCME CANO
-19A1C-X-X-X-XX-L-XX-L-YMD-NNNN
Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6,
Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C,
OKI=D, Philips=E, Renasas=F, Samsung=G, Sanyo=H, Sharp=I,
TI=J, Topro=K, Toshiba=L, Windbond=M
Year, month, day Year: 2001=1, 2002=2, 2003=3, 2004=4…
Month: 1~12=1, 2, 3, ~, 9, A, B, C
Day: 1~31= 1, 2, 3, ~, 9, A, B, C, ~, T, U, V
22 / 25
Version 3.1
Page 23
Doc. No.: 44086418
Issued Date: Jul, 04, 2008
Model No.: M190A1-L0C
Approval
NHCMO CAPG
10. PRECAUTIONS
10.1 ASSEMBL Y AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil
may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will
be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage
LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD module within
the specified storage conditions.
(10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
response time will become slowly, and the starting voltage of CCFL will be higher than room
temperature.
10.2 SAFETY PRECAUTIONS
(1) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while
assembling with inverter. Do not disa ssemble the module or insert anything into the Backlight unit.
(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washe d away thoroughly with soap.
(3) After the module’s end of life, it is not harmful in case of normal operation and storage.
www.jxlcd.com
www.jxlcd.com
23 / 25
Version 3.1
Page 24
www.jxlcd.com
www.jxlcd.com
Page 25
www.jxlcd.com
www.jxlcd.com
Loading...